Those entries are not used anymore.
CC: Florian Westphal <fw@strlen.de>
Fixes: 09c7570480 ("xfrm: remove flow cache")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We currently don't reload pointers pointing into skb header
after doing pskb_may_pull() in _decode_session4(). So in case
pskb_may_pull() changed the pointers, we read from random
memory. Fix this by putting all the needed infos on the
stack, so that we don't need to access the header pointers
after doing pskb_may_pull().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If an xfrmi is associated to a vrf layer 3 master device,
xfrm_policy_check() fails after traffic decapsulation. The input
interface is replaced by the layer 3 master device, and hence
xfrmi_decode_session() can't match the xfrmi anymore to satisfy
policy checking.
Extend ingress xfrmi lookup to honor the original layer 3 slave
device, allowing xfrm interfaces to operate within a vrf domain.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
esp_output_udp_encap can produce a length that doesn't fit in the 16
bits of a UDP header's length field. In that case, we'll send a
fragmented packet whose length is larger than IP_MAX_MTU (resulting in
"Oversized IP packet" warnings on receive) and with a bogus UDP
length.
To prevent this, add a length check to esp_output_udp_encap and return
-EMSGSIZE on failure.
This seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In commit 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
I introduced a check for xfrm protocol, but according to Herbert
IPSEC_PROTO_ANY should only be used as a wildcard for lookup, so
it should be removed from validate_tmpl().
And, IPSEC_PROTO_ANY is expected to only match 3 IPSec-specific
protocols, this is why xfrm_state_flush() could still miss
IPPROTO_ROUTING, which leads that those entries are left in
net->xfrm.state_all before exit net. Fix this by replacing
IPSEC_PROTO_ANY with zero.
This patch also extracts the check from validate_tmpl() to
xfrm_id_proto_valid() and uses it in parse_ipsecrequest().
With this, no other protocols should be added into xfrm.
Fixes: 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
Reported-by: syzbot+0bf0519d6e0de15914fe@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Removed info log-message if ipip tunnel registration fails during
module-initialization: it adds nothing to the error message that is
written on all failures.
Fixes: dd9ee34440 ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If tunnel registration failed during module initialization, the module
would fail to deregister the IPPROTO_COMP protocol and would attempt to
deregister the tunnel.
The tunnel was not deregistered during module-exit.
Fixes: dd9ee34440 ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This reverts commit f10e0010fa.
This commit was just wrong. It caused a lot of
syzbot warnings, so just revert it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When unloading xfrm6_tunnel module, xfrm6_tunnel_fini directly
frees the xfrm6_tunnel_spi_kmem. Maybe someone has gotten the
xfrm6_tunnel_spi, so need to wait it.
Fixes: 91cc3bb0b04ff("xfrm6_tunnel: RCU conversion")
Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
For rcu protected pointers, we'd better add '__rcu' for them.
Once added '__rcu' tag for rcu protected pointer, the sparse tool reports
warnings.
net/xfrm/xfrm_user.c:1198:39: sparse: expected struct sock *sk
net/xfrm/xfrm_user.c:1198:39: sparse: got struct sock [noderef] <asn:4> *nlsk
[...]
So introduce a new wrapper function of nlmsg_unicast to handle type
conversions.
This patch also fixes a direct access of a rcu protected socket.
Fixes: be33690d8fcf("[XFRM]: Fix aevent related crash")
Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In esp4_gro_receive() and esp6_gro_receive(), secpath can be allocated
without adding xfrm state to xvec. Then, sp->xvec[sp->len - 1] would
fail and result in dereferencing invalid pointer in esp4_gso_segment()
and esp6_gso_segment(). Reset secpath if xfrm function returns error.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Reported-by: syzbot+b69368fd933c6c592f4c@syzkaller.appspotmail.com
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
UBSAN report this:
UBSAN: Undefined behaviour in net/xfrm/xfrm_policy.c:1289:24
index 6 is out of range for type 'unsigned int [6]'
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.162-514.55.6.9.x86_64+ #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
0000000000000000 1466cf39b41b23c9 ffff8801f6b07a58 ffffffff81cb35f4
0000000041b58ab3 ffffffff83230f9c ffffffff81cb34e0 ffff8801f6b07a80
ffff8801f6b07a20 1466cf39b41b23c9 ffffffff851706e0 ffff8801f6b07ae8
Call Trace:
<IRQ> [<ffffffff81cb35f4>] __dump_stack lib/dump_stack.c:15 [inline]
<IRQ> [<ffffffff81cb35f4>] dump_stack+0x114/0x1a0 lib/dump_stack.c:51
[<ffffffff81d94225>] ubsan_epilogue+0x12/0x8f lib/ubsan.c:164
[<ffffffff81d954db>] __ubsan_handle_out_of_bounds+0x16e/0x1b2 lib/ubsan.c:382
[<ffffffff82a25acd>] __xfrm_policy_unlink+0x3dd/0x5b0 net/xfrm/xfrm_policy.c:1289
[<ffffffff82a2e572>] xfrm_policy_delete+0x52/0xb0 net/xfrm/xfrm_policy.c:1309
[<ffffffff82a3319b>] xfrm_policy_timer+0x30b/0x590 net/xfrm/xfrm_policy.c:243
[<ffffffff813d3927>] call_timer_fn+0x237/0x990 kernel/time/timer.c:1144
[<ffffffff813d8e7e>] __run_timers kernel/time/timer.c:1218 [inline]
[<ffffffff813d8e7e>] run_timer_softirq+0x6ce/0xb80 kernel/time/timer.c:1401
[<ffffffff8120d6f9>] __do_softirq+0x299/0xe10 kernel/softirq.c:273
[<ffffffff8120e676>] invoke_softirq kernel/softirq.c:350 [inline]
[<ffffffff8120e676>] irq_exit+0x216/0x2c0 kernel/softirq.c:391
[<ffffffff82c5edab>] exiting_irq arch/x86/include/asm/apic.h:652 [inline]
[<ffffffff82c5edab>] smp_apic_timer_interrupt+0x8b/0xc0 arch/x86/kernel/apic/apic.c:926
[<ffffffff82c5c985>] apic_timer_interrupt+0xa5/0xb0 arch/x86/entry/entry_64.S:735
<EOI> [<ffffffff81188096>] ? native_safe_halt+0x6/0x10 arch/x86/include/asm/irqflags.h:52
[<ffffffff810834d7>] arch_safe_halt arch/x86/include/asm/paravirt.h:111 [inline]
[<ffffffff810834d7>] default_idle+0x27/0x430 arch/x86/kernel/process.c:446
[<ffffffff81085f05>] arch_cpu_idle+0x15/0x20 arch/x86/kernel/process.c:437
[<ffffffff8132abc3>] default_idle_call+0x53/0x90 kernel/sched/idle.c:92
[<ffffffff8132b32d>] cpuidle_idle_call kernel/sched/idle.c:156 [inline]
[<ffffffff8132b32d>] cpu_idle_loop kernel/sched/idle.c:251 [inline]
[<ffffffff8132b32d>] cpu_startup_entry+0x60d/0x9a0 kernel/sched/idle.c:299
[<ffffffff8113e119>] start_secondary+0x3c9/0x560 arch/x86/kernel/smpboot.c:245
The issue is triggered as this:
xfrm_add_policy
-->verify_newpolicy_info //check the index provided by user with XFRM_POLICY_MAX
//In my case, the index is 0x6E6BB6, so it pass the check.
-->xfrm_policy_construct //copy the user's policy and set xfrm_policy_timer
-->xfrm_policy_insert
--> __xfrm_policy_link //use the orgin dir, in my case is 2
--> xfrm_gen_index //generate policy index, there is 0x6E6BB6
then xfrm_policy_timer be fired
xfrm_policy_timer
--> xfrm_policy_id2dir //get dir from (policy index & 7), in my case is 6
--> xfrm_policy_delete
--> __xfrm_policy_unlink //access policy_count[dir], trigger out of range access
Add xfrm_policy_id2dir check in verify_newpolicy_info, make sure the computed dir is
valid, to fix the issue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e682adf021 ("xfrm: Try to honor policy index if it's supplied by user")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b27 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.
In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:
"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"
That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/core-api/printk-formats.rst, size_t should be
printed with %zu, rather than %Zu.
In addition, using %Zu triggers a warning on clang (-Wformat-extra-args):
net/sctp/chunk.c:196:25: warning: data argument not used by format string [-Wformat-extra-args]
__func__, asoc, max_data);
~~~~~~~~~~~~~~~~^~~~~~~~~
./include/linux/printk.h:440:49: note: expanded from macro 'pr_warn_ratelimited'
printk_ratelimited(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
./include/linux/printk.h:424:17: note: expanded from macro 'printk_ratelimited'
printk(fmt, ##__VA_ARGS__); \
~~~ ^
Fixes: 5b5e0928f7 ("lib/vsprintf.c: remove %Z support")
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Matthias Maennich <maennich@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly
[10258690.371129] kernel BUG at net/core/skbuff.c:4028!
[10258690.371748] invalid opcode: 0000 [#1] SMP PTI
[10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G W 5.0.0-rc6 #2
[10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
[10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
[10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
[10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
[10258690.372094] FS: 0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
[10258690.372094] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
[10258690.372094] Call Trace:
[10258690.372094] <IRQ>
[10258690.372094] skb_to_sgvec+0x11/0x40
[10258690.372094] start_xmit+0x38c/0x520 [virtio_net]
[10258690.372094] dev_hard_start_xmit+0x9b/0x200
[10258690.372094] sch_direct_xmit+0xff/0x260
[10258690.372094] __qdisc_run+0x15e/0x4e0
[10258690.372094] net_tx_action+0x137/0x210
[10258690.372094] __do_softirq+0xd6/0x2a9
[10258690.372094] irq_exit+0xde/0xf0
[10258690.372094] smp_apic_timer_interrupt+0x74/0x140
[10258690.372094] apic_timer_interrupt+0xf/0x20
[10258690.372094] </IRQ>
In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.
Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.
To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.
Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
Signed-off-by: Sheng Lan <lansheng@huawei.com>
Reported-by: Qin Ji <jiqin.ji@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both
errors are embarassingly simple, and the fixes are straightforward.
As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: Jann Horn <jannh@google.com>
Fixes: 446fda4f26 ("[NetLabel]: CIPSOv4 engine")
Fixes: 3faa8f982f ("netlabel: Move bitmap manipulation functions to the NetLabel core.")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input_rcu expects the original ingress device (e.g., for
proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
so dev needs to be saved prior to calling it. This was the behavior prior
to the listify changes.
Fixes: 5fa12739a5 ("net: ipv4: listify ip_rcv_finish")
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
selftests: pmtu: fix and increase coverage
This series includes a fixup for the pmtu.sh test script, related to IPv6
address management, and adds coverage for the recently reported and fixed
PMTU exception issue
v2 -> v3:
- more cleanups
v1 -> v2:
- several script cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of new tests, explicitly checking that the kernel
timely releases PMTU exceptions on related device removal.
This is mostly a regression test vs the issue fixed by
commit f5b51fe804 ("ipv6: route: purge exception on removal")
Only 2 new test cases have been added, instead of extending all
the existing ones, because the reproducer requires executing
several commands and would slow down too much the tests otherwise.
v2 -> v3:
- more cleanup, still from Stefano
v1 -> v2:
- several script cleanups, as suggested by Stefano
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, the configured IPv6 address could be still "tentative"
at test time, possibly causing tests failures.
We can also drop some sleep along the code and decrease the
timeout for most commands so that the test runtime decreases.
v1 -> v2:
- fix comment (Stefano)
Fixes: d1f1b9cbf3 ("selftests: net: Introduce first PMTU test")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.
Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Fail route add with unsupported nexthop attribute
RTA_VIA was added for MPLS as a way of specifying a gateway from a
different address family. IPv4 and IPv6 do not currently support RTA_VIA
so using it leads to routes that are not what the user intended. Catch
and fail - returning a proper error message.
MPLS on the other hand does not support RTA_GATEWAY since it does not
make sense to have a nexthop from the MPLS address family. Similarly,
catch and fail - returning a proper error message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __icmp_send function having ip_options struct parameter
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9060cb719e ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat(). However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:
- base_sock_release
- bnep_sock_release
- cmtp_sock_release
- data_sock_release
- dn_release
- hci_sock_release
- hidp_sock_release
- iucv_sock_release
- l2cap_sock_release
- llcp_sock_release
- llc_ui_release
- rawsock_release
- rfcomm_sock_release
- sco_sock_release
- svc_release
- vcc_release
- x25_release
Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().
Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:
#include <pthread.h>
#include <stdlib.h>
#include <sys/socket.h>
#include <unistd.h>
pthread_t t;
volatile int fd;
void *close_thread(void *arg)
{
for (;;) {
usleep(rand() % 100);
close(fd);
}
}
int main()
{
pthread_create(&t, NULL, close_thread, NULL);
for (;;) {
fd = socket(rand() % 50, rand() % 11, 0);
fchownat(fd, "", 1000, 1000, 0x1000);
close(fd);
}
}
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
Fixes: ee28bb56ac ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the file names of the FW files which this driver handles into
the module description.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:
# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.
Fixes: c749cdda90 ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4e8ddd7f17 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:
# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.
Fixes: 4e8ddd7f17 ("net: sched: don't release reference on action overwrite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcclOnAAoJEL/70l94x66DAjIH/28XLAkaAtJIsm4nTy3sb6nC
UC7suhEEst4zyRCzUlMdeaMkuWJitx5Bun0x9k5uYvMXqmndXcGq3wLmrRhOY2u2
iN1myLESOn0+lubVcK/+ht2rat2AO9XqpOKPojBRs/c6MW1UAIJIPKly/ls1++Ee
TmdIKrgqGgE5Ywx4ObvXBDOeWSKUwxqqNi7FUkWpACJckvmQoKJX0Hre5ICW6lom
+yUBC1rR9apMLTe2QIW2kBZ9JTKCX0aErdmnLXlyZbFOOk0udzNaDy+kXSs7w9Bk
tu8biO7xBNJrcR5e+fEipVFIdN9au0aM5pJWq9s4yeqSnDKB1FRekoJj5yvTqus=
=1GQR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
