* Since we stop rx/tx dma and pcu durring reset there is no need to
call ath5k_hw_stop_rx/tx_dma before, also there is no need to call
them durring stop_locked since we can use ath5k_hw_dma_stop for
both.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Stop PCU receive logic (DRU) durring reset
We need to be sure pcu is not active when trying to stop rx dma
right now this is done on ath5k_reset (base.c) but later we are
going to clean it up.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add a new function to stop rx/tx dma and use in when reset starts
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* No functional changes
* Clean up reset:
Introduce init functions for each unit and call them instead
of having everything inside ath5k_hw_reset (it's just c/p for
now so nothing changes except calling order -I tested it with
various cards and it's ok-)
* Further cleanups:
ofdm_timings belongs to phy.c
rate_duration belongs to pcu.c
clock functions are general and belong to reset.c (more to follow)
* Reorder functions for better organization:
We start with helpers and other functions follow in categories,
init functions are last
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.
This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX aggregation locking documentation was
wrong, which led Christian to also code the
timer timeout handling for it somewhat wrongly.
Fix the documentation, the two places that
need to hold the reorder lock across accesses
to the structure, and the debugfs code that
should just use RCU.
Also, remove acquiring the sta->lock across
reorder timeouts since it isn't necessary, and
change a few places to GFP_KERNEL because the
code path here doesn't need atomic allocations
as I noticed when reviewing all this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent tx path cleanups moved the software retry count tracking
from the ath_buf to the skb cb, however the actual counter update
referred to the wrong location, confusing block-ack window tracking.
Fix this by using the retries counter in the struct ath_frame_info.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 446fad5a5b.
The change had broken the packet injection on monitoring mode.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not ideal to enable btcoex based on subsys id as it is
not unique, they are so random. It is also a pain keeping
all of them in a table to enable btcoex for a particular
hw. Going back to the old idea.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the new off-channel TX API
in mac80211 with a new work item type. The
operation doesn't add a new work item when
we're on the right channel and there's no
wait time so that for example p2p probe
responses will be transmitted without delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change to offical name for 100 devices:
"Intel(R) Centrino(R) Wireless-N 100"
Change to offical name for 130 devices:
"Intel(R) Centrino(R) Wireless-N 130"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Change to offical name for 6000g2b devices:
"Intel(R) Centrino(R) Wireless-N 1030"
"Intel(R) Centrino(R) Advanced-N 6230"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of hardcoding the numbers that must
match mac80211, use the constants. Not that
this means we could change the constants,
but at least this way it's clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Our hardware has reliable TX status, but we're
not currently advertising that to mac80211.
Since the packet loss monitoring will depend
on it, advertise it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since aggregation queues are station-specific, the
device will not reject packets in them but rather
will stop the appropriate aggregation queues when
a station goes to sleep. I forgot to account for
this in the driver, so if a station went to sleep
that had aggregation enabled, traffic would stop
indefinitely.
Fix this by only accounting frames queued on the
normal AC queues for associated station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Through races, a packet may be enqueued for
transmission to a station while that station
is going to sleep, in which case the warning
here triggers. Instead of warning, check the
condition -- if this packet is not a PS-poll
response then we still enqueue it but it will
be rejected by the device since the station
is marked as asleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The valid tx/rx antenna information is part of EEPROM, so use it
to configure the device.
For few cases, the EEPROM did not reflect the correct antenna, but
it is too late to modify the EEPROM, so overwrite with .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Categorize AR7010 & AR9287 devices based on driver_info
of usb_device_id, instead of PIDs. This avoids per-device cases
and minimize code changes for new device addition.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 devices (PCI/USB) use different eeprom start location
to read nvram. New devices might endup with same devid. So use
driver_info to set offset, instead of devid. driver_info is
valid for HTC devices alone which is filled in usb_device_id.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver_info stores the device category information which
is used to load appropriate device firmware, select firmware offset
and eeprom starting location. The driver_info is accessed across
ath9k_htc and ath9k_hw. Hence placed under common structure.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6000g2b and up, adding advance power management support
for better power consumption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If shadow register is enable, modify the power management
command to inform uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the BT PSPoll flag when fill PM command to uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding additional power management option available for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 7 of BT config flag is used to enable/disable PSPoll sync.
Make the name to match it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For drivers that have accurate TX status reporting
we can report the number of consecutive lost packets
to userspace using the new cfg80211 CQM event. The
threshold is fixed right now, this may need to be
improved in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help with latency issues which can happen when
using aggregation.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help with latency issues which can happen when
using aggregation.
Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since nullfunc frames are transmitted as unicast frames, they're more
reliable than the broadcast probe requests, so we need fewer retries
to figure out whether the AP is really gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nullfunc frames are better for connection monitoring, because probe requests
are answered even if the AP has already dropped the connection, whereas
nullfunc frames from an unassociated station will trigger a disassoc/deauth
frame from the AP (WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA), which allows
the station to reconnect immediately instead of waiting until it attempts to
transmit the next unicast frame.
This only works on hardware with reliable tx ACK reporting, any other hardware
needs to fall back to the probe request method.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the connection by probing the AP (either using nullfunc or a
probe request). If nullfunc probing is supported and the assoc is no
longer valid, the AP will send a disassoc/deauth immediately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a fixed 2 second timeout, calculate beacon loss interval
from the advertised beacon interval and a frame count. With this beacon
loss happens after N (default 7) consecutive frames are missed which
for a typical setup (100TU beacon interval) is ~700ms (or ~1/3 previous).
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some typos, warnings, initialize some values to follow wl's code path.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
