Add support to reassign vif in switch_vif_chanctx. This is similar to
the existing CHANCTX_SWMODE_SWAP_CONTEXTS mode, but doesn't delete the
old context nor creates a new one, doing to switch between two
existing contexts.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Currently we only support the CHANCTX_SWMODE_SWAP_CONTEXTS mode, but
we need to support other modes as well. Spin a new function off in
order to make it easier to support other modes.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We only need the csa_vif in AP/GO modes, and assigning for other
interfaces may cause problems, because csa_vif is never cleared. To
prevent this, only assign the value if the iftype is
NL80211_IFTYPE_AP. Use a switch to do this, even though, for now,
only the AP interface type is handled, because soon other interface
types will be added as well.
Additionally, convert the WARN() in the error case when a
channel-switch is already running to WARN_ONCE().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
A new callback has been added to prepare the device for a channel
switch. Use the new callback instead of the old channel_switch_beacon
operation.
This makes it possible to remove the channel_switch_beacon operation
from mac80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Maintain a TDLS channel-switch state and update it according to
notifications from FW and timeouts. Explicitly check all state
transitions are valid.
When switching is initiated by mac80211, use a delayed work to
periodically reschedule it from iwlwifi.
Give the FW mac80211 generated TDLS channel-switch request/response
templates. It will change appropriate values (switch timings) and Tx
them at appropriate times.
Enable the channel switch wiphy capability bit when the FW supports it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Block TID 4 (VI) on a vif when using TDLS. This TID will be used by FW
for TDLS channel-switch requests and PTI requests.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When adding a TDLS station, allocate 4 new queues for it. Configure them
to FW and enable them. On station removal, drain the queues if needed
and disable them when empty.
Make sure to flush all packets in the private queues of TDLS stations in
the mac80211 flush() callback.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS peers are present the FW will send packets on a dedicated
TID vs. the peer when performing TDLS channel-switches. The driver
configures the TID on connection to the peer and the FW is responsible
for maintaining the state of QoS seqno and PN/IV for encryption.
If the FW asserts, the driver cannot correctly reconfigure the starting
seqno/PN to the reloaded FW, thus forcing us to reconnect the peer.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TDLS stations will have private queues, so consider them as well when
allocating a new one. Consolidate the HW-queue iterating code into
a single exported function, to be used by the TDLS code in the future.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send a dedicated TDLS_CONFIG command when a TDLS peer joins/leaves. The
fields for the command are mostly place-holders, as most of the FW
functionality is not implemented. In the future the dedicated FW TID
will be used for channel-switching and buffer-sta functionality.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a channel-switch command and a switch-start notification. Also add a
FW TLV bit indicating TDLS channel switching support.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver/FW combination now support TDLS.
Check the FW support with the TLV bit.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we pre-populate the skb->head for the stack, we only pull
in the 802.11 header including crypto (assuming the packet isn't
short enough to be in there completely.) This is fine, but in
ieee80211_data_to_8023() we later unconditionally pull 8 more
bytes for the SNAP header and ethertype field (except for mesh
or 4-addr, where it's even more, but we don't care as much about
them).
Avoid the additional later pull by pulling in those 8 bytes here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we pre-populate the skb->head for the stack, we only pull
in the 802.11 header (assuming the packet isn't short enough to
be in there completely.) This is fine, but in many cases we'll
pull in the crypto headers pretty much immediately afterwards,
so to avoid that pull in the crypto header early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of building the rx_status on the stack and then
copying it to the skb, allocate the skb a bit earlier
and then build the rx_status in place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the original driver, we decided to not implement WEP RX hardware
offload because of a quirk with the firmware API - it allows setting
global WEP keys that then get used for all virtual interfaces, which
is clearly wrong if more than one exists, and it allows setting per-
station keys but then separates multicast and unicast keys.
In order to implement WEP RX hardware offload, work around these
limitations by uploading each WEP key twice, once as multicast and
once as unicast, but point them both to the same key slot (offset)
and use the same key material so the slot overwrite on the second
upload doesn't actually change anything. Upon removal, also remove
the key twice so the station no longer references it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the key add/remove functions to be able to reuse parts
of them later for RX WEP keys, which need to be uploaded twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a flow that handles the requests to cancel the roc time event,
that has been triggered via the aux framework.
The roc for bss is different than the roc for p2p devices, and is done
via the aux framework using the aux queue, thus requires a different flow
to cancel the time event.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove warning on scan complete with unknown ID, since this
scan could be already cleared in abort flow.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The ssid_bitmap should be unsigned, though it doesn't matter
much as the high bits aren't used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Identify 7265-D devices using the hardware revision (they have the
same PCI IDs as 7265) and change the configuration for them taking
the differences (currently only the firmware image) into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Older firmwares do not provide support for the HOT_SPOT_CMD command.
Check for the appropriate TLV flag that declares hotspot support in
the firmware to prevent a firmware assertion failure that can be
triggered from the userspace,
Cc: stable@vger.kernel.org [3.17+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Toggle the LMPM_CHICK register when writing chunks into the FW's extended
SRAM. This tells the FW to put the chunk into a different memory space.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no reason to pass every 50th beacon if
nothing was changed.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of allocating nd_ies separately, make it part of the iwl_mvm
structure so it's easier to handle its lifetime.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We were toggling the wrong bit when we reset the device,
fix that. Moreover, since the reset can take time, we need
to wait before we set the rfkill interrupt. Not doing so
can be racy since the driver is enabling the rfkill
interrupt while the device is resetting which will clear
all the registers including the CSR_INT_MASK.
This can basically lead to a situation where we don't
enable the rfkill interrupt. If that happens, the user will
not be able to re-enable the device when de-asserting
rfkill.
This scenario happened to the submitter of:
https://bugzilla.kernel.org/show_bug.cgi?id=87191
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For background and scheduled scan, using the new unified scan API,
support random MAC address scanning.
Unfortunately, the firmware right now doesn't support randomising
itself, so for now do it on the host - we'll change this once the
firmware supports randomising the address for each scan iteration
using the address/mask.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LMAC TLV bit may be on in FWs that support UMAC scan; so check
for UMAC TLV bit first.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The fw now indicates missing BA with ampdu_ack_len=0.
This will make the whole aggregation being marked
as failed, although it's most likely not the case (and
only the BA itself was failed).
Consider this case as a single tx failure.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The TTC and RRC features are supported by the newer
firmwares. It allows to reach better overall WiFi and BT
performance. When the RRC is enabled, we don't need to force
the AP to send SISO frames, but it can keeps sending MIMO
frames.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This API uses second CPU scan commands, and can support multiple
simultaneous scans.
Adding the new API, and adding new mechanisms to deal with up to
8 simultaneous scans instead of the old scan status.
New scan API requires scan configuration for default scan parameters,
adding it in _up flow. Also updating scan configuration after updating
valid scan antennas via debugfs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver must set the keep alive period regardless of power
management state. The keep alive period must be greater or equal to
both the NIC's maximum sleep period, and the listen interval.
However, we were confusing time units (TU) and msec, so fix that.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our firmware scheduler suffers from false wake-up on 500 time units.
that is if the dtim interval exceeds 500 time units, the fw wakes up,
understands that the next wake-up event is still ahead, and if this event
is more than 10msec in the future - goes back to sleep, otherwise - stay
awake. For example, say that the beacon interval is 101 and the dtim
period is 5, the dtim interval is 101 x 5 = 505, and we will stay awake
for those extra 5msec.
So on the one hand the dtim interval should be congruent to the beacon
interval times the dtim period, and on the other should minimize
the false wake-ups event.
This change applies only to D0/D3 power modes.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The deferred d0i3 exit is currently implemented in the
resume op, which is called when mac80211 starts its
resume process.
However, mac80211 still doesn't handle frames at this stage,
which results in frames being dropped.
Move the deferred d0i3 handling to the reconfig_complete
callback, in order to make sure mac80211 is fully available
at this point.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After the corresponding mac80211 patch, we can now report the airtime
used for each transmitted packet and mac80211 will be able to implement
WMM-AC with that information.
To support WMM-AC in the driver then, report the airtime and advertise
support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add two new parameters to iwl_cfg:
max_ht_ampdu_exponent and max_vht_ampdu_exponent.
These parameters, if set, will set new values to the maximum of
HT and VHT A-MPDU exponent for the A-MPDU length exponent.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since it's too complicated for the fw to insert a DS Parameter Set
element in the middle of the frame, it was decided that it should be
done by the host. The fw will only parse the frame and update the
current channel field.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A properly set alpha2 value consists of two chars that both contain
letters or digits. If no value is set, both chars keep their initial
value zero. Therefore do not send the alpha2 parameter to user space
if either of the characters has been left at its initial zero value.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adds new VID/PID for the Marvell 88W8766. The kernel currently only supports
the device as PCI, but it is also available using USB. An example of a device
delivered with the 88W8766 as USB is the Globalscale Mirabox.
TX buffer size is set to driver default (2K), as we do not know the firmware
requirement.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions brcmu_pkt_buf_free_skb() and release_firmware() test whether
their argument is NULL and then return immediately. Thus the test around
the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people
-----BEGIN PGP SIGNATURE-----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=q4e6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.
This issue was revealed by kbuild testing
when <asm/unaligned.h> was added in <linux/ieee80211.h>
resulting in redefinition of get_unaligned_be16 (and
probably others).
Cc: stable@vger.kernel.org # v3.17
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmented Rx wasn't reporting everything. With
the reworked Rx code it's very easy to fix it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it more in line with the new Rx path.
It also makes the code more reusable because Rx
descriptor is more accessible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original fix has been moved into a different
place in the code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This creates a single, common path for MSDU,
A-MSDU and fragmented Rx.
Hopefully this will make it easier to understand
Rx path and make it easier to work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the rx_confused be handled by the rx
indication handlers instead of the buffer popping
function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since htt_rx_mpdu_status isn't used anymore
(instead attention flags are used) simplify the
loop.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using manual sk_buff linking via ->next
use sk_buff_head. It's more robust, cleaner and
there's plenty of helper functions in kernel
already to manage sk_buff_head.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
currently ath9k_common depends on this components.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HWSIM_CMD_GET_RADIO returns information about a specific radio id or
all of them in response to a dump. Create the netlink skb or use the
one provided by the dump functionality. Use the existing attribute
appending function to fill in the same attributes when creating a
new hwsim radio.
Save alpha2 and struct ieee80211_regdomain in the hwsim data or else
they will be lost in the depths of regulatory infrastructure.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out netlink message attribute appending in order to reuse it
with later code. As a result move netlink skb allocation to the
calling function.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The hwname will always be set if idx is negative (as it's
a u32 read into an s64 it can't overflow either) so we can
remove the unnecessary check for hwname being non-NULL.
This was reported by smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can always know the hwname of the radio so use the value
from wiphy.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for scanning with random MAC address for
both software and hardware scan.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This brings in some mwifiex changes that further patches will
need to work on top to not cause merge conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when a roc period expires, the offchannel
timer calls ieee80211_remain_on_channel_expired(), but
the roc state is cleared only when the queued work
to switch to the operating channel gets a chance to run.
This race is a problem because mac80211 can issue a
new roc request in this window. To avoid this, handle
roc completion in the offchannel timer itself.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a GO/STA setup, when we switch to the STA context,
the channel context timer is scheduled with a period of
half the beacon interval. If a beacon is received in
this duration, the timer is adjusted to accommodate
TSF sync done by the HW.
But, if the actual channel switch is delayed for some
reason, we end up rearming the timer every time a new
beacon is received. Avoid this by doing the adjustment
only once.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If for some reason a beacon with a new NoA is
not sent out, then reset the mgd_prepare_tx flag.
Not doing this will result in a situation where
a GO will send a new NoA when it shouldn't.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that pending roc/scan
operations are cancelled properly when a new
context is assigned/unassigned.
The flush_work() call to flush out any scheduled
channel context work is removed, instead, sc->mutex
is dropped to allow any pending work to get a chance
to complete by the channel scheduler. Also, increase
the timeout to allow a switch to an active GO.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a pending roc or scan operation is cancelled,
the offchannel operation is cleared, but the offchannel
state in the main scheduler is not cleared. This causes
problems since an active GO will try to process a stale
offchannel request that was deferred earlier. Fix this
by clearing the state when there is no pending offchannel
(roc/scan) operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers that control the on-chip thermometer
need to be programmed based on the chainmask that
the solution supports, not the chainmask that is
present in the eeprom.
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.
Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.
So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.
This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n
and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing TDLS discovery
frames. After parsing, we update peer RSSI information.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds auto TDLS support to mwifiex.
Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WMM support for TDLS link. Patch
add WMM info IE for TDLS setup request/response frames
while WMM parameter for TDLS confirm frame.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX packet descriptor structure has recently changed in FW.
This patch updates rxpd accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.
So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.
Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.
Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Cc: stable@vger.kernel.org # v3.17
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kill the submitted URB in brcmf_usb_dl_cmd if the request timed out. This
assures the URB is never submitted twice. It also prevents a possible
use-after-free of the URB transfer buffer if a timeout occurs.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.
To record tx ieee80211 headers
trace-cmd record -e ath10k_tx_hdr
To record complete packets
trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While preparing an ad-hoc start command, the capability info bitmap is
needlessly set from the command, and then the ESS bit cleared.
Change to set the bitmap directly without reference to the command.
Signed-off-by: James Cameron <quozl@laptop.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wlcore_cmd_send_failsafe() function is only called in the cmd.c
file, where it is definde. Make it static.
Additionally, move the EXPORT_SYMBOL macro for wl1271_cmd_send() to
the right place.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for the minimum required buffer length in wlcore_cmd_send() and
wlcore_cmd_configure_failsafe. This ensures that we will never try to
use a buffer that is smaller than the required header.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's been observed that wrong firmware version (ex. 66.14.96.p9
instead of 14.66.9.p96) is displayed on big endian platforms.
The problem is fixed here.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use code provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use values provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason it didn't coused obvious problems.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
not sure why.
Initially provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename exports from ath9k_spectral_* to ath9k_cmn_spectral_*
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we should be ready to make this code common.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
last preparation before moving ath9k_spectral_scan_ to spectral.c
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we don't have here any ieee80211_hw dependencies any way.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spectral code mostly depends on ath_hw, not on ath_softc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this will alow us to make ath_softc independent code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and move rfs_chan_spec_scan to this struct. We will need it
for common spectral scan code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We see this warning while starting mwifiex AP:
Unsupported RX-STBC, default to 2x2
This was happening because of wrong offset while copying HT
capabilities from BSS configuration of start_ap handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is observed that device sometimes sends BA setup requests for
broadcast mac address.
This patch adds a check to avoid checking availability of
AMPDU/AMSDU streams for broadcast mac address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some platforms, system goes out of memory during heavy
Rx traffic with our USB chipsets.
In case of SDIO/PCIe, after receiving 50 packets in Rx queue
we stop processing interrupts till packets pending fall below
low threshold i.e 20. We don't have similar logic for USB,
so if host platform is slow, we would hit a case where firmware
keeps on pushing packets at high speed than driver/kernel can
process.
We will stop submitting URBs for Rx data when pending packet
count reaches high threshold and restart them when enough
packets are consumed to solve the problem.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=85071
Reported-by: Marek Belisko <marek.belisko@gmail.com>
Tested-by: Marek Belisko <marek.belisko@gmail.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes redundant data complete handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds RX workqueue support for USB interfaces.
Currently rx_pending is applicable for cmd/events and Rx
data in USB interface. Let's use it only for Rx data.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track it per channel context instead of in the softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function chandef_to_chanspec() failed when converting a
chandef with bandwidth set to NL80211_CHAN_WIDTH_20_NOHT. This
was reported by user running the device in AP mode.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 304 at
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:381
chandef_to_chanspec.isra.11+0x158/0x184()
Modules linked in:
CPU: 0 PID: 304 Comm: hostapd Not tainted 3.16.0-rc7-abb+g64aa90f #8
[<c0014bb4>] (unwind_backtrace) from [<c0012314>] (show_stack+0x10/0x14)
[<c0012314>] (show_stack) from [<c001d3f8>] (warn_slowpath_common+0x6c/0x8c)
[<c001d3f8>] (warn_slowpath_common) from [<c001d4b4>] (warn_slowpath_null+0x1c/0x24)
[<c001d4b4>] (warn_slowpath_null) from [<c03449a4>] (chandef_to_chanspec.isra.11+0x158/0x184)
[<c03449a4>] (chandef_to_chanspec.isra.11) from [<c0348e00>] (brcmf_cfg80211_start_ap+0x1e4/0x614)
[<c0348e00>] (brcmf_cfg80211_start_ap) from [<c04d1468>] (nl80211_start_ap+0x288/0x414)
[<c04d1468>] (nl80211_start_ap) from [<c043d144>] (genl_rcv_msg+0x21c/0x38c)
[<c043d144>] (genl_rcv_msg) from [<c043c740>] (netlink_rcv_skb+0xac/0xc0)
[<c043c740>] (netlink_rcv_skb) from [<c043cf14>] (genl_rcv+0x20/0x34)
[<c043cf14>] (genl_rcv) from [<c043c0a0>] (netlink_unicast+0x150/0x20c)
[<c043c0a0>] (netlink_unicast) from [<c043c4b8>] (netlink_sendmsg+0x2b8/0x398)
[<c043c4b8>] (netlink_sendmsg) from [<c04066a4>] (sock_sendmsg+0x84/0xa8)
[<c04066a4>] (sock_sendmsg) from [<c0407c5c>] (___sys_sendmsg.part.29+0x268/0x278)
[<c0407c5c>] (___sys_sendmsg.part.29) from [<c0408bdc>] (__sys_sendmsg+0x4c/0x7c)
[<c0408bdc>] (__sys_sendmsg) from [<c000ec60>] (ret_fast_syscall+0x0/0x44)
---[ end trace 965ee2158c9905a2 ]---
Cc: stable@vger.kernel.org # v3.17
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.
For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.
Patch fixes skb_under_panic problems reported from time to time:
https://bugzilla.kernel.org/show_bug.cgi?id=84911https://bugzilla.kernel.org/show_bug.cgi?id=72471http://marc.info/?l=linux-wireless&m=139108549530402&w=2https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi>
Debugged-by: Antti S. Lankila <alankila@bel.fi>
Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lnlA
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aborting d0i3 due to taken refs, other threads might
already wait on d0i3_exit_waitq for IWL_MVM_STATUS_IN_D0I3
to get cleared (it's somewhat likely, as synchronize_rcu()
might take a while), so make sure to wake them up.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some rare cases, the firmware can put the device to
sleep after the driver requested the access. This is
because the access request can take a short time to be
propagated to the firmware.
If that happens, the driver may think that it has access
since the firmware hasn't put the device to sleep yet, but
right after the driver's check, the firmware might put the
device to sleep.
Warn when this happens by allowing the firmware to finish
the "put the device sleep" flow so that the driver will
not get access to the device. This will make the issue
visible.
This still doesn't fix the race, but at least it makes
it more visible.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently, the firmware only sends temperature notificaitions inside
RX statistics notifications, which are tied to beacon filtering. This
is a problem because beacon filtering is not used with vifs that don't
receive beacons (e.g. P2P GO and AP), so the driver doesn't receive
temperature notifications in those cases. To solve that, the firmware
will be changed so that it sends DTS_MEASUREMENT_NOTIFICATIONs,
independently from the beacon filtering flows.
To support that, the driver needs to also handle unsolicited
DTS_MEASUREMENT_NOTIFICATIONs, that are not triggered by
DTS_TRIGGER_CMD_FLAGS_TEMP requests.
This change is backwards compatible and will simply not be used with
firmware versions that do not send the notifications.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the temperature handling code so that it is easier to reuse
it with other notification flows.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The code to capture firmware errors works during the reconfiguration
phase after an error. As the D3->D0 transition uses the same flow to
get the D0 image reconfigured, this triggered and caused a firmware
coredump to be collected. This in turn, if it isn't picked up by
userspace, can cause module unloading to fail, which is how the bug
was detected.
To fix this issue, introduce a new status flag (D3_RECONFIG) and use
it to detect that during reconfiguration no coredump should be taken
and reported.
Reported-by: Avi Kraif <avix.kraif@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we need only one antenna, we should refrain from using
the antenna that is shared with BT if BT load is high.
Fix this.
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When Tx STBC is being used and RS switches to a search column
using the alternate antenna from the current one there is a
problem with using rs_rate_match to figure out which table
is the active and which one is the search one. The root cause
is because in STBC the antenna mask in the ucode rate is set
to ANT_AB and in this specific scenario it matches both the
active and search table (e.g. SISO_ANT_A and SISO_ANT_B).
This leads to tx stats being updated in the wrong table and later
on to getting stuck in a test window and not moving on to other
columns. If this happens during the initial search cycle we
never end it and therefore never enable aggregation which leads
naturally to severe througput degradation.
Fix it by deducing which table is which by knowing whether we're
in a search or not like it's being done in rs_rate_scale_perform
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Other contexts might call iwl_mvm_ref_sync() right before
we set IWL_MVM_STATUS_IN_D0I3, and then assume the fw/bus
is not in d0i3 state.
However, since we currently don't check for held references
in the d0i3_enter flow, we might enter d0i3 although there
is an active reference.
Solve it by aborting the d0i3 enter flow if there is an
active reference. Since users are assumed to use
iwl_mvm_ref_sync, which takes a ref before checking the
flag, we don't need further locking.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This was taken care of in case we're doing STBC with HT
but not when working with VHT.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Even if running the driver with param init_dbg=1 - on INIT
image error - iwl_trans_stop_device() was still called. This
patch fixes that and calls iwl_trans_stop_device() on INIT
image failure only if init_dbg=0.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.
Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2cf7 ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The variable 'tid' is already defined in this function, so use
just 't' for the new one. As we return from the function just
overwriting 'tid' would be acceptable, but less obvious to the
reader.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Mostly functions related to building Tx-commands for sending to FW.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The status variable should be unsigned as the function call
requires a u32 not int pointer, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
phy_read and phy_write are not set for every phy any more sine this:
commit d342b95dd7
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Thu Jul 31 21:59:43 2014 +0200
b43: don't duplicate common PHY read/write ops
b43_phy_copy() accesses phy_read and phy_write directly and will fail
with some phys. This patch fixes the regression by using the
b43_phy_read() and b43_phy_write() functions which should be used for
read and write access.
This should fix this bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=87731
Reported-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Tested-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes in the vendor driver were added to rtlwifi, but some updates
to rtl8192se were missed, and the driver could neither scan nor connect.
There are other changes that will enhance performance, but this minimal
set fix the basic functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are typos in the handling of the descriptor pointers where the wrong
descriptor is referenced. There is also an error in which the pointer is
incremented twice.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device RTL8192EE uses a new form of trx flow. This fix sets up the descriptors
correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions
-----BEGIN PGP SIGNATURE-----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=6GIj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel.
-----BEGIN PGP SIGNATURE-----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=8uwd
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3v6b
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware was crashing when we were trying to warm reset it
after suspend. This was due to the fact that target registeres
can be accessed only if the hardware is awaken.
This patch makes sure to awake the device also on the hif up,
not only in case of probe call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing implementation of reset_resume handler just calls
ath6kl_usb_remove() that deallocates all resources.
It can lead to double free, etc. on disconnect.
The patch removes reset_resume handler,
so usb core could conservatively reset the driver.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.
Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231
CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch add cfg80211 dump_survey handler for mwifiex.
This handler will be called to report channel statistics
to cfg80211.
This in turn adds ACS support for mwifiex AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to record channel statistics during
scan. With extended scan, scan results are returned as events from
FW while channel statistics are part of scan command response.
We store these channel statistics in adapter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When deleting old radio via HWSIM_CMD_DEL_RADIO then listeners on the
multicast group "config" are informed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding new radio via HWSIM_CMD_NEW_RADIO then listeners on the
multicast group "config" are informed.
While at it, refactor the configuration parameters to be able to
pass them directly and have fewer function arguments.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix my mistake while sending Johannes's
commit aadede6e9f
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Oct 9 17:01:36 2014 +0200
iwlwifi: mvm: port to devcoredump framework
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A few recent additions to the netlink attributes neglected
to add policy entries, fix that now.
Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.
Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.
Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now it was possible to simulate soft and
hard fw crashes but it wasn't possible to trigger
an immediately hw restart itself (without the fw
crash).
This can be useful when stress testing hw
restarting stability, e.g. during heavy tx/rx
traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While testing other things I've found that CE
items aren't cleared properly. This could lead to
null dereferences in BMI.
To prevent that make sure CE revoking clears the
nbytes value (which is used as a buffer completion
indication) and memset the entire CE ring data
shared between host and target when
(re)initializing.
Also make sure to check BMI xfer pointer and print
a splat instead of crashing the kernel.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently hif_power_up performs effectively a
reset and hif_stop resets the chip as well so
there's no point in resetting here.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power up procedure was overly complex due to
warm/cold reset workarounds and issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One of the problems with warm reset I've found is
that it must be guaranteed that copy engine
registers are not being accessed while being
reset. Otherwise in worst case scenario the host
may lock up.
Instead of using sleeps and hoping the device is
operational in some arbitrary timeframes use
firmware indication register.
As a side effect this makes driver
boot/stop/recovery faster.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make ath10k_pci_init_pipes() effectively only
alter shared target-host data.
The per_transfer_context is a host-only thing.
It is necessary to preserve it's contents for a
more robust ring cleanup.
This is required for future warm reset fixes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The kbuild test robot reports that there are extra semicolons in this
driver. All of them are caused by using "};" rather than "}" at the
end of a switch statement. This patch does not change any functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 802.11 statistics obtained from the device can be retrieved
dumping the 'macstat' file in debugfs folder.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 802.11 core statistics are retrieved from the core registers
but not stored. So the debug code was never triggered to give a
warning message on tx underruns or rx overflows. This patch fixes
this and assures the statistics are stored in the snapshot.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the inline function instead of directly indexing the array.
This allows some architectures with hardware instructions
for bit reversals to eliminate the array.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible to configure driver using mtu_max module parameter
by setting it to value in range of 68..7920 inclusive.
This is sub-optimal performance-wise in case packet is larger than 1 page.
mtu_max default value is 2228.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of FW error, make it clear (in dmesg) what branch is taken
in the error recovery code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnect flow may be invoked either from upper layer request,
or from event reported by the firmware.
In case of firmware event, driver need to release resources for the station but
not send another disconnect WMI command.
In case of upper layer request, WMI_DISCONNECT_STA_CMDID command need to
be issued for the firmware to perform disconnect on the MAC layer. Eventually,
event is expected to confirm MAC disconnect, but it is better to not wait for
firmware event and release station resources immediately. FW may fail to
report disconnect for various reasons, so one could not rely on event always reported.
Introduce parameter to distinguish 2 cases above to prevent double WMI command
issuing.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As communicated with the firmware & hardware teams
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When interface is down, recovery flow should not be attempted.
Next ndo_open() will trigger target reset, that is FW recovery.
Doing recovery while interface is down cause internal "up", leaving
internal driver state in conflict with network stack. Then, when network
stack will call ndo_open(), kernel oops will be triggered.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
prec_enq is a sdio specific function. Move it to sdio.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename sdio_host.h to sdio.h and dhd_sdio.c to sdio.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename sdio_host.h to sdio.h and dhd_sdio.c to sdio.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__brcmf_err is a tracepoint specific function. Move it to
tracepoint.c.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packet filters got configured but never used.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Passing the firmware error codes up the driver may be mapped to
linux error numbers which may impact proper fault analysis. So
better pass up a generic failure code, ie. -EBADE and only show
firmware error code in FIL debug message.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The define EBRCMF_UNSUPPORTED is not used in the source file so this
patch removes it.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Showing the firmware error allows to quickly give a clue what
went wrong and directly look in the firmware code that gave us
back the error.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds wowl support for SDIO bus devices. This feature
requires FW which has support for wowl built in.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds wowl support for USB bus devices. This feature
requires FW which has support for wowl built in.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce pulse_rssi threshold to 15 in order to improve radar pattern detection
probability on ext channel
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
firmware to wake up the platform when a specific network
is detected. Along with that I have fixes for d3 operation.
The usual amount of rate scaling stuff - we now support STBC.
The other commit that stands out is Johannes's work on
devcoredump. He basically starts to use the standard
infrastructure he built.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GpBe
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-john-2014-10-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Emmanuel Grumbach <egrumbach@gmail.com> says:
"The big new thing here is netdetect which allows the
firmware to wake up the platform when a specific network
is detected. Along with that I have fixes for d3 operation.
The usual amount of rate scaling stuff - we now support STBC.
The other commit that stands out is Johannes's work on
devcoredump. He basically starts to use the standard
infrastructure he built."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error in the code makes the allocated space for firmware to be too
small.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
