Add dev_type parameter to struct ath10k_bus_params.
The dev type specifies if the device is a high latency device (usb and
sdio) or low latency device (pci, ahb and snoc)
The setup of high latency chips is sometimes different than
for chips using low latency interfaces.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This struct is used as argument to ath10k_core_register in order to
make it easier to add more bus parameters in the future.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Downloading firmware via BMI protocol takes too long time. For example,
a ~700K bytes firmware takes about 500ms to download via BMI protocol.
This is too long especially in suspend and resume scenario where firmware
is re-downloaded unless WoWLAN is enabled. Downloading firmware via diag CE
can reduce the time to ~40ms for a ~700K bytes firmware binary.
Ath10k driver parses the firmware to segments and downloads the segments
to the specified address directly. If the firmware is compressed or has
unsupported segments, ath10k driver will try BMI download again.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To download firmware via diag interface, driver needs to write the target
memory space below 1M. It means the bit20 should be zero for the converted
address if the target memory space is below 1M. Otherwise, bit20 is one if
the target address is larger or equal to 1M space.
As downloading firmware via diag interface is only required for qca6174
and qca9377, a new specific function is introduced to convert the target
address to ce address: ath10k_pci_qca6174_targ_cpu_to_ce_addri().
This function supports to convert any target address to ce address.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delay 1ms is too long for both diag read and write operations.
This is observed when writing a big memory buffer to target or
reading a big memory buffer from target. Take writing/reading
512k bytes as example, the delay itself is 256ms as the maximum
length of every write/read is 2k size.
Reduce the delay to 50us for read and write operations.
Take the ath10k_pci_targ_cpu_to_ce_addr() out of loop and put it
in the beginning of the loop for ath10k_pci_diag_read_mem().
The ath10k_pci_targ_cpu_to_ce_addr() is to convert the address
from target cpu's perspective to CE's perspective, so it makes
no sense to convert a CE's perspective address again in the loop.
It's a wrong implementation but happens to work.
If the target address is below 1M space, then the convert in the loop
from the second time becomes wrong because the previously converted address
is larger than 1M. The counterpart ath10k_pci_diag_write_mem() has the
correct implementation.
With this change, ath10k_pci_diage_read_mem() works correctly no matter
the target address is below 1M or above 1M.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Average ack rssi value is weighted average of ack rssi for
no of msdu's has been sent.
This feature is enabled by the host driver if firmware is capable.
After receiving event from host, firmware allocates the necessary
memory to store the ack_rssi for data packets during the init time.
After each successful transmission, If tx completion status is OK
and 24th bit is set in HTT message header then host will fetch the
ack_rssi else host can ignore the ack_rssi field.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
array "ctl_power_table" access index "pream" is initialized with -1 and
is raised as a static analysis tool issue.
[drivers\net\wireless\ath\ath10k\wmi.c:4719] ->
[drivers\net\wireless\ath\ath10k\wmi.c:4730]: (error) Array index -1 is
out of bounds.
Since the "pream" index for accessing ctl_power_table array is initialized
with -1, there is a chance of memory access violation for the cases below.
1) wmi_pdev_tpc_final_table_event change frequency is between 2483 and 5180
2) pream_idx is out of the enumeration ranges of wmi_tpc_pream_2ghz,
wmi_tpc_pream_5ghz
Signed-off-by: K.T.VIJAYAKUMAAR <vijay.bvb@samsung.com>
[kvalo@codeaurora.org: clean up the warning message]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds 'tx_stats' in per station debugfs entry.
Use this command to dump tx_stats:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds per station tx statistics support.
Per station tx stats include
- pkts/bytes transmitted at all possible rates(mcs/nss/bw/gi).
- ACK fails count
- ampdu bytes/pkts transmitted at all possible rates(mcs/nss/bw/gi).
- BA fails count
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds debugfs entry to enable/disable extended
tx statistics. Extended tx statistics are from peer stats
feature.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get the legacy rate index to update the pkts/bytes counter
against each possible tx rate.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The comparison of cid >= 0 is always true because cid is of type u8
(8 bits, unsigned).
Fix this by removing such comparison and updating the type of
variable cid to u8 in the caller function.
Addresses-Coverity-ID: 1473079 ("Unsigned compared against 0")
Fixes: b9010f105f ("wil6210: add FT roam support for AP and station")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 target uses separate htc service for pktlog.
Add pktlog service request and support for pktlog
rx path handling.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Existing copy engine interrupt enable logic assumes that last
CE is using polling mode and due to this interrupt for last copy engine
are always disabled. WCN3990 uses last CE for pktlog and
interrupt remains disabled with existing logic.
To mitigate this issue, introduce CE_ATTR_POLL flag and control
the interrupt based on the flag which can be set in ce_attr.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support dual-band variant of QCA9984, new extended board data (eBDF)
is introduced since existing board data ran out of space.
Below is the brief implementation & design detail,
----------------------------------------------------
1. New OTP changes to inform eBDF support in existing OTP download to
fetch board ID and chip ID. This is backward compatible and older
card sends 0 by default for eBDF support bit (bit 18 of OTP response) we
check in ath10k driver.
2. If eBDF is supported, then we need to fetch eBDF ID which is bundled
in downloaded board data. So again OTP is executed for knowing the eBDF ID.
This is done once we set 'board_data_initialized' bit. If eBDF ID
returned is zero, we continue booting with previous board data downloaded.
3. Based on the eBDF ID fetched, ath10k driver tries to download the
extended board data to a new offset ahead of already downloaded board
data address.
4. A new BD IE type, ATH10K_BD_IE_BOARD_EXT is added to differentiate in
bundling eBDF separately in board-2.bin and also to parse through
board bundle for eBDF download in ath10k boot.
5. If eBDF is not present in the board-2.bin bundle or when board ID is
zero, we do a fallback boot to "eboard.bin" in the same QCA9984/hw1.0 dir.
This is same as done to existing "board.bin" if board ID is not present
in board-2.bin bundle.
Current design is that eBDF size will be 2KB and eBDF ID will be
byte value.
Tested the above changes with dual-band variant of QCA9984 card. OTP
update needed for the test will be part of next FW release 10.4-3.6-xxxx.
Below are the logs with ath10k BOOT debugs enabled.
First OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for board id
boot get otp board id result 0x00040400 board_id 1 chip_id 0 ext_bid_support 1
..
Second OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for ext board id
boot get otp ext board id result 0x00000005 ext_board_id 5
boot using eboard name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
..
Extended board data download:
------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 65 62 6f 61 72 64 -id=0,bmi-eboard
00000020: 2d 69 64 3d 35 -id=5
boot found match for name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
boot found eboard data for 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
using board api 2
boot writing ext board data to addr 0xc3000
..
Fallback Extended board data download from "eboard.bin":
---------------------------------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 62 6f 61 72 64 2d -id=0,bmi-board-
00000020: 69 64 3d 31 30 id=10
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-eboard-id=5 from ath10k/QCA9984/hw1.0/board-2.bin
boot fw request 'ath10k/QCA9984/hw1.0/eboard.bin': 0
using board api 1
boot writing ext board data to addr 0xc3000
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Just moving functions down in the file, no functional changes.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ATH10K_SNOC builds just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are some tx packets pending in firmware, and then system
enters suspend, firmware will fail for wow enable. This will trigger
mac80211 to stop ath10k and download firmware again, then it is
non-wow suspend.
After add the waiting htt tx complete, then firmware will have some
time window to send or flush the pending tx packets.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Devices may provide their own MAC address via system firmware (e.g.,
device tree), especially in the case where the device doesn't have a
useful EEPROM on which to store its MAC address (e.g., for integrated
Wifi).
Use the generic device helper to retrieve the MAC address, and (if
present) honor it above the MAC address advertised by the card.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.20. Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check rx_buff_mgmt is allocated before accessing its internal fields.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This feature is needed for enterprise APs and clients to enable
fast roaming as defined in 802.11r between APs in the same ESS.
On AP side, this feature is supported only when disable_ap_sme
is enabled.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil_addba_rx_request allocates the rx reorder buffer regardless
of use_rx_hw_reordering settings.
Fix this by checking wil->use_rx_hw_reordering before allocating
the reorder buffer.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil6210 supports channels 1-3 of the 60GHz band.
New FW added support for channel 4. Add support for channel 4 also in
wil6210 driver.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset file is not used and may cause race conditions
with operational driver if used.
Signed-off-by: Karthick Gopalasubramanian <kargop@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Array firstep_table is being assigned but is never used
hence it is redundant and can be removed.
Cleans up clang warning:
warning: 'firstep_table' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.
Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.
2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
Wang.
3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
Borkmann.
4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
attackers using it as a side-channel. From Eric Dumazet.
5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.
6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
Liu.
7) hns and hns3 bug fixes from Huazhong Tan.
8) Fix RIF leak in mlxsw driver, from Ido Schimmel.
9) iova range check fix in vhost, from Jason Wang.
10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.
11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.
12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.
13) TCP BBR congestion control fixes from Kevin Yang.
14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.
15) qed driver fixes from Tomer Tayar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: sched: Fix memory exposure from short TCA_U32_SEL
qed: fix spelling mistake "comparsion" -> "comparison"
vhost: correctly check the iova range when waking virtqueue
qlge: Fix netdev features configuration.
net: macb: do not disable MDIO bus at open/close time
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
i40e: fix condition of WARN_ONCE for stat strings
i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
ixgbe: fix driver behaviour after issuing VFLR
ixgbe: Prevent unsupported configurations with XDP
ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
igb: Use an advanced ctx descriptor for launchtime
e1000: ensure to free old tx/rx rings in set_ringparam()
e1000: check on netif_running() before calling e1000_up()
ixgb: use dma_zalloc_coherent instead of allocator/memset
ice: Trivial formatting fixes
...
The email was botched in one entry, and I also forgot to update the
location of the git tree. It'll be under the linux-block umbrella, just
with different branches.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Fixes: 7634ccd2da ("libata: maintainership update")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Via u32_change(), TCA_U32_SEL has an unspecified type in the netlink
policy, so max length isn't enforced, only minimum. This means nkeys
(from userspace) was being trusted without checking the actual size of
nla_len(), which could lead to a memory over-read, and ultimately an
exposure via a call to u32_dump(). Reachability is CAP_NET_ADMIN within
a namespace.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer update from Thomas Gleixner:
"New defines for the compat time* types so they can be shared between
32bit and 64bit builds. Not used yet, but merging them now allows the
actual conversions to be merged through different maintainer trees
without dependencies
We still have compat interfaces for 32bit on 64bit even with the new
2038 safe timespec/val variants because pointer size is different. And
for the old style timespec/val interfaces we need yet another 'compat'
interface for both 32bit native and 32bit on 64bit"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
y2038: Provide aliases for compat helpers
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
- Lift gcc test into Kconfig
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=8D/M
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugin fix from Kees Cook:
"Lift gcc test into Kconfig. This is for better behavior when the
kernel is built with Clang, reported by Stefan Agner"
* tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Disable when building under Clang
Pull perf updates from Thomas Gleixner:
"Kernel:
- Improve kallsyms coverage
- Add x86 entry trampolines to kcore
- Fix ARM SPE handling
- Correct PPC event post processing
Tools:
- Make the build system more robust
- Small fixes and enhancements all over the place
- Update kernel ABI header copies
- Preparatory work for converting libtraceevnt to a shared library
- License cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
tools arch x86: Update tools's copy of cpufeatures.h
perf python: Fix pyrf_evlist__read_on_cpu() interface
perf mmap: Store real cpu number in 'struct perf_mmap'
perf tools: Remove ext from struct kmod_path
perf tools: Add gzip_is_compressed function
perf tools: Add lzma_is_compressed function
perf tools: Add is_compressed callback to compressions array
perf tools: Move the temp file processing into decompress_kmodule
perf tools: Use compression id in decompress_kmodule()
perf tools: Store compression id into struct dso
perf tools: Add compression id into 'struct kmod_path'
perf tools: Make is_supported_compression() static
perf tools: Make decompress_to_file() function static
perf tools: Get rid of dso__needs_decompress() call in __open_dso()
perf tools: Get rid of dso__needs_decompress() call in symbol__disassemble()
perf tools: Get rid of dso__needs_decompress() call in read_object_code()
tools lib traceevent: Change to SPDX License format
perf llvm: Allow passing options to llc in addition to clang
perf parser: Improve error message for PMU address filters
...
Pull x86 fixes from Thomas Gleixner:
- Correct the L1TF fallout on 32bit and the off by one in the 'too much
RAM for protection' calculation.
- Add a helpful kernel message for the 'too much RAM' case
- Unbreak the VDSO in case that the compiler desides to use indirect
jumps/calls and emits retpolines which cannot be resolved because the
kernel uses its own thunks, which does not work for the VDSO. Make it
use the builtin thunks.
- Re-export start_thread() which was unexported when the 32/64bit
implementation was unified. start_thread() is required by modular
binfmt handlers.
- Trivial cleanups
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/l1tf: Suggest what to do on systems with too much RAM
x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM
x86/kvm/vmx: Remove duplicate l1d flush definitions
x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
x86/process: Re-export start_thread()
x86/mce: Add notifier_block forward declaration
x86/vdso: Fix vDSO build if a retpoline is emitted
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
Pull licking update from Thomas Gleixner:
"Mark the switch cases which fall through to the next case with the
proper comment so the fallthrough compiler checks can be enabled"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Mark expected switch fall-throughs
* memory_failure() gets confused by dev_pagemap backed mappings. The
recovery code has specific enabling for several possible page states
that needs new enabling to handle poison in dax mappings. Teach
memory_failure() about ZONE_DEVICE pages.
-----BEGIN PGP SIGNATURE-----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=Ftop
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm memory-failure update from Dave Jiang:
"As it stands, memory_failure() gets thoroughly confused by dev_pagemap
backed mappings. The recovery code has specific enabling for several
possible page states and needs new enabling to handle poison in dax
mappings.
In order to support reliable reverse mapping of user space addresses:
1/ Add new locking in the memory_failure() rmap path to prevent races
that would typically be handled by the page lock.
2/ Since dev_pagemap pages are hidden from the page allocator and the
"compound page" accounting machinery, add a mechanism to determine
the size of the mapping that encompasses a given poisoned pfn.
3/ Given pmem errors can be repaired, change the speculatively
accessed poison protection, mce_unmap_kpfn(), to be reversible and
otherwise allow ongoing access from the kernel.
A side effect of this enabling is that MADV_HWPOISON becomes usable
for dax mappings, however the primary motivation is to allow the
system to survive userspace consumption of hardware-poison via dax.
Specifically the current behavior is:
mce: Uncorrected hardware memory error in user-access at af34214200
{1}[Hardware Error]: It has been corrected by h/w and requires no further action
mce: [Hardware Error]: Machine check events logged
{1}[Hardware Error]: event severity: corrected
Memory failure: 0xaf34214: reserved kernel page still referenced by 1 users
[..]
Memory failure: 0xaf34214: recovery action for reserved kernel page: Failed
mce: Memory error not recovered
<reboot>
...and with these changes:
Injecting memory failure for pfn 0x20cb00 at process virtual address 0x7f763dd00000
Memory failure: 0x20cb00: Killing dax-pmd:5421 due to hardware memory corruption
Memory failure: 0x20cb00: recovery action for dax page: Recovered
Given all the cross dependencies I propose taking this through
nvdimm.git with acks from Naoya, x86/core, x86/RAS, and of course dax
folks"
* tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pmem: Restore page attributes when clearing errors
x86/memory_failure: Introduce {set, clear}_mce_nospec()
x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses
mm, memory_failure: Teach memory_failure() about dev_pagemap pages
filesystem-dax: Introduce dax_lock_mapping_entry()
mm, memory_failure: Collect mapping size in collect_procs()
mm, madvise_inject_error: Let memory_failure() optionally take a page reference
mm, dev_pagemap: Do not clear ->mapping on final put
mm, madvise_inject_error: Disable MADV_SOFT_OFFLINE for ZONE_DEVICE pages
filesystem-dax: Set page->index
device-dax: Set page->index
device-dax: Enable page_mapping()
device-dax: Convert to vmf_insert_mixed and vm_fault_t
