Separate IF and BW based registers.
Add support for DVB-T and DVB-T2 6MHz channel bandwidth.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is not ready enough to be released on mainline.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement initial support for DVB-T and DVB-T2 modes. Now driver has
basic support for all the modes, DVB-C/T/T2.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It uses I2C bus so better to implement it as a standard I2C driver
model. It was using proprietary DVB binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Original plan was to implement driver as one file per used demod
standard (mn88472_c.c, mn88472_t.c and mn88472_t2.c). However, that
plan was a mistake as driver code differences are so small between
different standards. Due to that rename this file and implement all
the needed functionality to that file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
400ms delay seems to be enough in order to gain DVB-C lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wrong symbol name causes demod attach failure.
Reported-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only DVB-C mode is supported, DVB-T and DVB-T2 are not supported.
Very much feature reduced version, no signal statistics nor normal
chip configuration options.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1> When m88ds3103 works in serial ts mode, its serial ts clock is equal to ts master clock and the clock divider is bypassed.
2> The serial ts clock is configed by the bridge driver just like parallel ts clock.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
move the return to happen before the logic. This way, we can
avoid one extra identation.
This also fixes an identation issue on this function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is hard to read what's there, because it doesn't follow the
CodingStyle.
Add missing whitespaces to split function arguments.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is actually a false positive:
drivers/media/dvb-frontends/cx24110.c:210 cx24110_set_fec() error: buffer overflow 'rate' 7 <= 8
But fixing it is easy: just ensure that the table size will be
limited to FEC_AUTO.
While here, fix spacing on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by spatch:
drivers/media/dvb-frontends/stb0899_drv.c:720 stb0899_send_diseqc_msg() error: buffer overflow 'cmd->msg' 6 <= 7
The buffer size is 6 and not 8. Anyway, the best is to use sizeof(),
to avoid such mistakes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As sparse complains:
drivers/media/dvb-frontends/stv090x.c:3471:30: warning: mixing different enum types
drivers/media/dvb-frontends/stv090x.c:3471:30: int enum fe_delivery_system versus
drivers/media/dvb-frontends/stv090x.c:3471:30: int enum stv090x_delsys
There's actually an error when setting the delivery system on
stv090x_search(): it is using the DVBv5 macros as if they were
the stv090x ones.
Instead, we should convert between the two namespaces, returning
an error if an unsupported delivery system is requested.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That case is not IO error, so better to jump out now, but still
continue polling.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch changed both AF9030 and IT9130 SNR reporting from
dB to relative. Restore AF9030 to old behavior as it has been always
returning 0.1 dB value. Leave IT9130 relative as old IT9130 was
returning relative values.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Snr returns value not correct. Fix it.
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Check return status after each register access routine and avoid
masking return status values.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch changes used signal strength firmware register from
0x800048 to 0x80004a in case of AF9033/AF9035 chip. In practice
reported values were running upside-down, when RR strength increases
reported value decreases and vice versa. That is because of 0x80004a
returns values that are dBm scale, but negative RF strength dBm
returned as positive number.
0x800048 returns 0-100, like percentage
0x80004a returns 0-255 dBm, without a negative sign
So restore old measurement now.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Register 0x800048 is not dB measure but relative scale. Fix it and conform to NorDig specifications.
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It repeated "found a 'Silicon Labs Si2168' in warm state" everytime
when device was opened. Message is aimed to point out firmware is
downloaded, up and running. So print it only in case firmware download
is performed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
M88RS6000 is the integrated chip, which includes tuner and demod. Its
internal demod is similar with M88DS3103 except some registers
definition.
The main different part of this internal demod from others is its
clock/pll generation IP block sitting inside the tuner die. So clock/pll
functions should be configed through its tuner i2c bus, NOT its demod
i2c bus.
The demod of M88RS6000 need the firmware: dvb-demod-m88rs6000.fw
firmware download link:
http://www.dvbsky.net/download/linux/dvbsky-firmware.tar.gz
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This code is needlessly complicated and checkpatch.pl complains that we
go over the 80 characters per line limit.
If we flip the "if (!lock) {" test to "if (lock) return;" then we can
remove an indent level from the rest of the function.
We can add two returns in the "if (state->srate >= 10000000) {"
condition and move the else statement back an additional indent level.
There is another "if (!lock) {" check which can be removed since we have
already checked "lock" and know it is zero at this point. This second
check on "lock" is also a problem because it sets off a static checker
warning. I have reviewed this code for some time to see if something
else was intended, but have concluded that it was simply an oversight
and should be removed. Removing this duplicative check gains us an
third indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Improves lock performance with signals from the ZeeVee family
of modulators.
Signed-off-by: Richard Vollkommer <linux@hauppauge.com>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not
automatically power down. This blocks other receivers connected
to a satellite channel router (EN50494), since the receivers can not send the
required DiSEqC sequences when the Tevii card is connected to a the same SCR.
This patch switches off the LNB supply voltage on initialization of the frontend.
[mchehab@osg.samsung.com: add a comment about why we're explicitly
turning off voltage at device init]
Cc: stable@vger.kernel.org
Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Incorrect struct used in the SP2 driver.
Reported-by: Max Nibble <nibble.max@gmail.com>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch partially reverts 0fb220f2a5. What happened is
that the conversion of debug messages to use pr_debug() was a
bad idea, because one needing to debug would need to both
enable debug level via a modprobe parameter, and then to
enable the dynamic printk's.
So, for now, let's use printk() directly at dprintk().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dib7000p is for DVB, and not ISDB. So, there's no layer.
That removes this compilation warning:
drivers/media/dvb-frontends/dib7000p.c:1972: warning: 'i' is used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DUbD
-----END PGP SIGNATURE-----
Merge tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new IR driver: hix5hd2-ir
- the virtual test driver (vivi) was replaced by vivid, with has an
almost complete set of features to emulate most v4l2 devices and
properly test all sorts of userspace apps
- the as102 driver had several bugs fixed and was properly split into a
frontend and a core driver. With that, it got promoted from staging
into mainstream
- one new CI driver got added for CIMaX SP2/SP2HF (sp2 driver)
- one new frontend driver for Toshiba ISDB-T/ISDB-S demod (tc90522)
- one new PCI driver for ISDB-T/ISDB-S (pt3 driver)
- saa7134 driver got support for go7007-based devices
- added a new PCI driver for Techwell 68xx chipsets (tw68)
- a new platform driver was added (coda)
- new tuner drivers: mxl301rf and qm1d1c0042
- a new DVB USB driver was added for DVBSky S860 & similar devices
- added a new SDR driver (hackrf)
- usbtv got audio support
- several platform drivers are now compiled with COMPILE_TEST
- a series of compiler fixup patches, making sparse/spatch happier with
the media stuff and removing several warnings, especially on those
platform drivers that didn't use to compile on x86
- Support for several new modern devices got added
- lots of other fixes, improvements and cleanups
* tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (544 commits)
[media] ir-hix5hd2: fix build on c6x arch
[media] pt3: fix DTV FE I2C driver load error paths
Revert "[media] media: em28xx - remove reset_resume interface"
[media] exynos4-is: fix some warnings when compiling on arm64
[media] usb drivers: use %zu instead of %zd
[media] pci drivers: use %zu instead of %zd
[media] dvb-frontends: use %zu instead of %zd
[media] s5p-mfc: Fix several printk warnings
[media] s5p_mfc_opr: Fix warnings
[media] ti-vpe: Fix typecast
[media] s3c-camif: fix dma_addr_t printks
[media] s5p_mfc_opr_v6: get rid of warnings when compiled with 64 bits
[media] s5p_mfc_opr_v5: Fix lots of warnings on x86_64
[media] em28xx: Fix identation
[media] drxd: remove a dead code
[media] saa7146: remove return after BUG()
[media] cx88: remove return after BUG()
[media] cx88: fix cards table CodingStyle
[media] radio-sf16fmr2: declare some structs as static
[media] radio-sf16fmi: declare pnp_attached as static
...
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
drivers/media/dvb-frontends/drxd_hard.c:2839 drxd_init() info: ignoring unreachable code.
Firmware request/release is not at drxd_init. So, we can remove
that dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PLP selection was implemented for Si2168 last month (patchwork 25387). However, FE_CAN_MULTISTREAM was not added to dvb_frontend_ops of si2168. This patch adds FE_CAN_MULTISTREAM, which indicates that multiple PLP are supported.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/built-in.o: In function `tc90522t_get_frontend':
>> tc90522.c:(.text+0x260b64c): undefined reference to `__divdi3'
>> tc90522.c:(.text+0x260b685): undefined reference to `__divdi3'
>> tc90522.c:(.text+0x260b6bb): undefined reference to `__divdi3'
>> tc90522.c:(.text+0x260b713): undefined reference to `__divdi3'
drivers/built-in.o:tc90522.c:(.text+0x260bb64): more undefined references to `__divdi3' follow
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/tc90522.c:706:5: warning: symbol 'tc90522_functionality' was not declared. Should it be static?
drivers/media/dvb-frontends/tc90522.c:706:5: warning: no previous prototype for 'tc90522_functionality' [-Wmissing-prototypes]
u32 tc90522_functionality(struct i2c_adapter *adap)
^
Cc: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds driver for tc90522 demodulator chips.
The chip contains 4 demod modules that run in parallel and are independently
controllable via separate I2C addresses.
Two of the modules are for ISDB-T and the rest for ISDB-S.
It is used in earthsoft pt3 cards.
Note that this driver does not init the chip,
because the initilization sequence / register setting is not disclosed.
Thus, the driver assumes that the chips are initilized externally
by its parent board driver before fe->ops->init() are called.
Earthsoft PT3 PCIe card, for example, contains the init sequence
in its private memory and provides a command to trigger the sequence.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"len" is user controlled and can be up to 255. Anything more than 59
will cause a buffer overflow so we need to add a test for that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Additionally print chip name with revision symbolically.
This is a preparation for supporting new Hauppauge WinTV-HVR-900-H based
on cx231xx.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current firmware is only for revision D.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
cab_state->modulation is initialized with a wrong value:
drivers/media/dvb-frontends/stv0367.c:3000:42: warning: mixing different enum types
drivers/media/dvb-frontends/stv0367.c:3000:42: int enum fe_modulation versus
drivers/media/dvb-frontends/stv0367.c:3000:42: int enum stv0367cab_mod
as it was declared as "enum stv0367cab_mod". While it could be fixed,
there's no value on it, as this is never used.
So, just remove the modulation from cab_state structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It was using the wrong constant for QAM256 on get_frontend.
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just returns whatever error that was returned by the i2c core,
in the case of errors, only returning -EREMOTEIO if the transfer size
is not what it was expected.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The returned code is 0, 1 or an error. It doesn't make sense to
print it in hexadecimal.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to init supported stats here in order signal app which
stats are supported.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Statistics are now calculated for DVBv5 and those DVBv5 values are
returned for legacy DVBv3 calls also. So we could remove all old
statistics calculation logic.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBv5 BER is calculated anyway, so just return it for legacy
read_ber() API too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement following DTV API commands:
DTV_STAT_POST_ERROR_BIT_COUNT
DTV_STAT_POST_TOTAL_BIT_COUNT
These will provide post-Viterbi bit error rate reporting.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement following API commands:
DTV_STAT_ERROR_BLOCK_COUNT
DTV_STAT_TOTAL_BLOCK_COUNT
These returns total and uncorrected error packets from outer FEC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let the demod firmware estimate RF signal strength and return it
to the app as a dBm. To handle that, use thread which reads signal
strengths from firmware in 2 sec intervals when device is active.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I2C driver address is passed as a i2c_new_device() parameter when
device is created. Thus no need to keep it in config struct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It uses I2C client so logging system prints module name
automatically. Function name is also added automatically, if it is
requested from dynamic debug by setting proper format.
Because of that, we could simplify logging in our driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
foo_dev seems to be most correct term for the structure holding data
of each device instance. It is most used term in Kernel codebase and also
examples from book Linux Device Drivers, Third Edition, uses it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
AF9030 and IT9130 series has different memory location for firmware
version. Choose correct location according to chip type.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
AF903x/IT913x demod provides clock source(s). It seems that this
clock source is used for integrated RF tuner of IT913x. It is
enabled by default, but firmware disables it automatically when
suspend is requested (suspend_flag (0x004c) + trigger_ofsm
(0x0000)). Automatic disable behavior seems to be similar for both
AF903x and IT913x I tested, though there is no likely any real
clock user in a case of AF903x.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a variable to keep track if firmware is loaded or not and skip parts of the
initialization if fw is already loaded. Resume from sleep with a different
command compared to initial power up and run command 85 after resume command.
This behaviour is observed when using manufacturer provided binary-only si2168
driver for TechnoTrend CT2-4400.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove function name from debug logs. Logging system could add it
automatically.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sample rate calculation gives a little bit too large results because
in real life there was around one milliseconds (~one usb packet) too
much data for given time. Calculate time more accurate in order to
provide better results.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init flags before calling spin_lock_irqsave().
spin_lock_irqsave is macro which stores value to 'flags'
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IT9135 RF tuner clock is coming from demodulator. We need enable it
early in demod init, before any tuner I/O. Currently it is enabled
by tuner driver itself, but it is too late and performance will be
reduced as some registers are not updated correctly. Clock is
disabled automatically when demod is put onto sleep.
Cc: <stable@vger.kernel.org> # v3.15+
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxk_hard.c:2224:3-22: code aligned with following code on line 2227
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by cocinelle:
drivers/media/dvb-frontends/drxd_hard.c:2632:3-51: code aligned with following code on line 2633
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by cocinelle:
drivers/media/dvb-frontends/sp8870.c:395:2-14: code aligned with following code on line 397
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
instead of testing if it is false or true, just use
if (!foo) or if (foo). That makes the code easier to
read and shorter.
Also, properly initialize booleans with true or false.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using 0 or 1 for boolean, use the true/false
defines.
Also, instead of testing foo == false, just use the
simplified notation if(!foo).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The error return code STV0900_NO_ERROR happens only once, at
the end of the functions. So, just return it directly.
This driver should actually be fixed to return standard
Linux error codes, instead of its own macros, but this
should be done on a separate patchset.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/stv0367.c:557:5: warning: symbol 'stv0367cab_RF_LookUp1' was not declared. Should it be static?
drivers/media/dvb-frontends/stv0367.c:569:5: warning: symbol 'stv0367cab_RF_LookUp2' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/mb86a16.c:31:14: warning: symbol 'verbose' was not declared. Should it be static?
drivers/media/dvb-frontends/mb86a20s.c:36:4: warning: symbol 'mb86a20s_subchannel' was not declared. Should it be static?
drivers/media/dvb-frontends/mb86a20s.c:1333:24: warning: symbol 'cnr_qpsk_table' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/dib7000p.c:2562:5: warning: symbol 'dib7090_set_diversity_in' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add some error checking and implement functionality a little bit
differently.
Cc: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver for the CIMaX SP2 common interface chip. It is very much based on
the existing cimax2 driver for cx23885, but should be more reusable. The
product has been sold with name Atmel T90FJR as well and the data sheets
for that chip seem to be publicly available.
It seems that the USB device that I have and the cx23885 based devices will
need to interact differently with the chip for the CAM operations. Thus
there is one callback function that is passed on to the sp2 driver
(see function sp2_ci_op_cam for that one).
IRQ functionality is not included currently (not needed by USB devices
and I don't have a PCIe device for development).
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Luis Alves submitted a TS mode patch to si2168 earlier, but the
patch was rejected due to a small issue. Here is a working version.
Also, setting of TS mode is moved from si2168_set_frontend to
si2168_init.
This patch adds the TS mode as a config option for the si2168 demod:
- ts_mode added to config struct.
- Possible (interesting) values are
* Parallel mode = 0x06
* Serial mode = 0x03
Currently the modules using this demod only use parallel mode.
Patches for these modules later in this patch series.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement set voltage operation.
Separate TS clock as a own configuration parameter.
Add TS clock polarity parameter.
[crope@iki.fi: merge em28xx driver m88ds3103 config change patch
to that one, in order to keep build unbroken]
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Same thing for si2168 as Antti did earlier for tda18212:
There is no need to print module name nor function name as those
are done by kernel logging system when dev_xxx logging is used and
driver is proper I2C driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to get FE_HAS_SYNC, the viterbi should already be
locked too. So, add the missing FE_HAS_VITERBI lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Kbuildtest:
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:57:9: warning: 'struct si2165_config' declared inside parameter list [enabled by default]
struct i2c_adapter *i2c)
^
drivers/media/dvb-frontends/si2165.h:57:9: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:157:21: error: variable 'hauppauge_930C_HD_1113xx_si2165_config' has initializer but incomplete type
static const struct si2165_config hauppauge_930C_HD_1113xx_si2165_config = {
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: error: unknown field 'i2c_addr' specified in initializer
.i2c_addr = 0x64,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: warning: excess elements in struct initializer [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: error: unknown field 'chip_mode' specified in initializer
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:15: error: 'SI2165_MODE_PLL_XTAL' undeclared here (not in a function)
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: warning: excess elements in struct initializer [enabled by default]
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: error: unknown field 'ref_freq_Hz' specified in initializer
.ref_freq_Hz = 16000000,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: warning: excess elements in struct initializer [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:163:21: error: variable 'pctv_quatro_stick_1114xx_si2165_config' has initializer but incomplete type
static const struct si2165_config pctv_quatro_stick_1114xx_si2165_config = {
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: error: unknown field 'i2c_addr' specified in initializer
.i2c_addr = 0x64,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: warning: excess elements in struct initializer [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: error: unknown field 'chip_mode' specified in initializer
.chip_mode = SI2165_MODE_PLL_EXT,
^
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:165:15: error: 'SI2165_MODE_PLL_EXT' undeclared here (not in a function)
.chip_mode = SI2165_MODE_PLL_EXT,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: warning: excess elements in struct initializer [enabled by default]
.chip_mode = SI2165_MODE_PLL_EXT,
^
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: error: unknown field 'ref_freq_Hz' specified in initializer
.ref_freq_Hz = 24000000,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: warning: excess elements in struct initializer [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c: In function 'dvb_init':
drivers/media/usb/cx231xx/cx231xx-dvb.c:731:3: warning: passing argument 1 of 'si2165_attach' from incompatible pointer type [enabled by default]
dev->dvb->frontend = dvb_attach(si2165_attach,
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:55:36: note: expected 'const struct si2165_config *' but argument is of type 'const struct si2165_config *'
static inline struct dvb_frontend *si2165_attach(
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:764:3: warning: passing argument 1 of 'si2165_attach' from incompatible pointer type [enabled by default]
dev->dvb->frontend = dvb_attach(si2165_attach,
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:55:36: note: expected 'const struct si2165_config *' but argument is of type 'const struct si2165_config *'
static inline struct dvb_frontend *si2165_attach(
^
That happens because the frontend was disabled by .config, but the
si2165_attach void stub require those structs, and also the
drivers that call it.
While here, remove the duplicated info about the possible I2C
addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DVB-T was tested with 8MHz BW channels in germany
This driver is the simplest possible, it uses automatic mode for all
parameters (TPS).
Added spectrum inversion support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drx39xxj_set_lna() and drx39xxj_set_frontend() set LNA. Instead of
duplicating LNA configure code, change to use drxj_set_lna_state()
which sets LNA to the caller requested state (on or off).
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Several functions ignore the return values in error legs and always
return -EIO. This makes it hard to debug and take proper action in
calling routines.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drx39xyj driver lacks resume support. Add support by changing
its fe ops init interface to detect the resume status by checking
fe exit flag and do the necessary initialization. With this change,
driver resume correctly in both dvb adapter is not in use and in use
by an application cases.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change drx39xyj_release() to check fe exit flag to detect the
device disconnect state and avoid accessing the device after
it has been removed.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes error:
[next:master 7435/8702] ERROR: "usb_alloc_urb
[drivers/media/dvb-frontends/rtl2832_sdr.ko] undefined!
rtl2832_sdr driver implements own USB streaming for SDR data.
Logically that functionality belongs to USB interface driver, but
currently it is implemented here.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the null test on ch. ch is initialized at the
beginning of the function to &demod->dtv_property_cache. Since demod
is dereferenced prior to the null test, demod must be a valid pointer,
and &demod->dtv_property_cache cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of looking at the guard interval field, it was using
the interval length, with is wrong. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Interleaving code was wrong at mb86a20s: instead, it was looking
at the Guard Interval. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver was reporting an incorrect mode, when mode 2
is selected.
While testing it, noticed that neither mode 1 or guard
interval 1/32 is supported by this device. Document it,
and ensure that it will report _AUTO when it doesn't lock,
in order to not report a wrong detection to userspace.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was 32-bit calculation overflow. Use div_u64.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This cleans up some line over 80 character violations.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This removes checks of struct member addresses since they likely result
in the condition always being true. Also in the stb6100_get_bandwidth
and tda8261_get_bandwidth functions the pointers frontend_ops and
tuner_ops are assigned the same addresses twice.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This updated patch also fixes out of bound access to b[].
In dib9000_risc_apb_access_write() an out of bound access to mb[].
The current test to avoid out of bound access to mb[] is insufficient.
For len = 19 non-existent mb[10] will be accessed.
For odd values of len b[] is accessed out of bounds.
For large values of len an of bound access to mb[] may occur in
dib9000_mbx_send_attr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
>From the context this should be hex 0x80 instead of decimal 80.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset a733291d69 didn't merge the fixes well. It ended by
restoring some bad logic removed there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da
(v4l2-ctrls: increase internal min/max/step/def to 64 bit)
changes v4l2 controls to 64-bit. Driver it not working on 32-bit
arch as it uses directly control 'step' which is changed to 64-bit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Testing demod presence on probe fails if the demod was sleep mode.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case of failure the return value was always 0. Return proper
error code (ENODEV) instead.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Improve scanning performance by setting property 0301 with a value
from Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds symbol rate setting to the driver.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move emulated format behind module parameter as those are not
supported. Format conversions will be on library eventually.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rework firmware selection logic a little bit.
Print notice asking user update firmware when old Si2168 B40
firmware is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver uses that new firmware too, so advertise it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add handling for different chip revisions and firmwares.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Command 0x14 returns 4 bytes as a reply. It is used for setting
key/value pairs to firmware and it returns 4 bytes back including
old value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to set explicitly value that are already defaulted same.
Setting new value returns old value. Firmware default values can
be found just looking returned value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Same command was executed twice, but different value. Remove
redundant command.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use memcpy for set cmd buffer in order to keep style in line with
rest of file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Detected symbol rate value was returned too small.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Inversion ON was reported as inversion OFF and vice versa.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
FEC AUTO is valid for PSK-8 modulation too. Add it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only supported modulation for DVB-S is QPSK. Modulation parameter
contains invalid value for DVB-S on some cases, which leads driver
refusing tuning attempt. Due to that, hard code modulation to QPSK
in case of DVB-S.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The message is currently highly encoded:
[70299.863521] DiB8000: Mpeg locks [ L0 : 0 | L1 : 1 | L2 : 0 ]
And doesn't properly reflect that some problems might have happened.
Instead, display it as:
[75160.822321] DiB8000: Not all ISDB-T layers locked in 32 ms: Layer A NOT LOCKED, Layer B locked, Layer C not enabled
In order to better reflect what's happening with layer locking.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When debug is enabled:
- Report when frontend gets restarted;
- Be coherent on the displayed lines;
- Show the transmission mode;
- Hide unused layers.
No functional changes (except at the printk's).
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This table doesn't match the new one.
Update it.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of doing the tuning delays and timeouts using
current_kernel_time(), use jiffies. That consumes less
CPU cycles, and it is monotonic.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
msleep() is not too precise: its precision depends on the
HZ config. As the driver selects precise timings for the
state machine, change it to usleep_range().
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
msleep() is not too precise: its precision depends on the
HZ config. As the driver selects precise timings for the
state machine, change it to usleep_range().
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the Windows driver, restart SAD during reset
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TV broadcasters generally use partial reception. So, enable it by
default in auto-search mode. The driver will latter detect if the
transmission is on some other mode.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The symbol duration was already obtained at CT_DEMOD_START.
No need to do it again at CT_DEMOD_STEP_3.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Without that, tuning may fail on 4K FFT mode, as the transmission
parameter cache will be initialized with a wrong value.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are two tabs instead of one aligning this struct.
Worse than that, on some places, the alignment is wrong.
Fix it.
No functional changes.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADC OFF values are wrong. This causes troubles on detecting
weak signals.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If interleave is bigger than 2, the code will set it to 0, as
dib8000 registers use a log2(). So, change the code to handle
it accordingly.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add static to tda m_* variables in the header. They don't need to be global.
With some cleanup they could probably even be marked const.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=68191
Reported-by: Christian Schneider <christian@ch-sc.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several issues on the current code:
1) msleep(1) is actually equivalent to msleep(10);
2) au8522_video_set() will set reg 0xa4 to the
proper value for SIF, CVBS or S-Video. No need
to force it to CVBS;
3) Let's not hardcode 0x9d for CBS on audio_set.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
setup_decoder_defaults() doesn't really care about the input
port. All it needs to know is if the input port is s-video or
not.
As the caller function already knows that, just pass a boolean
instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's set the the audio routing also at stream start. With this change,
we don't risk enabling the analog demux while not streaming, reducing
the risk of interfering with a DVB demux that might be happening.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same demod is used on both analog and digital mode. We should
not let the commands for analog mode to happen while the device
is in digital mode. So, monitor it via streamon.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The input mode is used not only inside the setup_decoder_defaults()
but also at au8522_*_mode routines.
So, move it one level up. As an advantage, we can now group the
function that sets the input into just one.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
First 8 bytes belonging to firmware image were hard-coded and uploaded
by the driver mistakenly. Introduce new corrected firmware file and
remove those 8 bytes from the driver.
New firmware image could be extracted from the PCTV 292e driver CD
using following command:
$ dd if=/TVC 6.4.8/Driver/PCTV Empia/emOEM.sys ibs=1 skip=1089408 count=2728 of=dvb-demod-si2168-02.fw
$ md5sum dvb-demod-si2168-02.fw
d8da7ff67cd56cd8aa4e101aea45e052 dvb-demod-si2168-02.fw
$ sudo cp dvb-demod-si2168-02.fw /lib/firmware/
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix following warnings:
si2168_cmd_execute() warn: add some parenthesis here?
si2168_cmd_execute() warn: maybe use && instead of &
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Calibrate the signal strength to dB.
For this callibration, I used adapter 0 (antenna 1), connected
via a normal cable to a DTF-2111 generator.
The same cabling and RF generator connected to adapter 1
(antenna 2) has a difference of +3dBm (signal was stronger
there).
Yet, changing the RF for a difference of, let's say, 6dB
reflected on a 6dB difference at the measured signal, with
is good.
So, the signal strengh can indeed be used to measure the
antenna gain, if the antenna is repositioned. It is
not precise to measure the absolute dBm value, however.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds DVBv5 stats support. For now, just mimic whatever dib8000
does, as they're very similar, with regards to statistics.
However, dib7000p_get_time_us() likely require some
adjustments, as I didn't actually reviewed the formula
for it to work with DVB-T. Still, better than nothing,
as latter patches can improve it.
This patch also doesn't show the signal strength in dB
yet. The code is already there, but it requires to be
callibrated.
A latter patch will do the calibration.
It seems that this patch is also a bug fix: Before this
patch, the frontend were not tuning with some userspace
tools. I suspect that dib7000p firmware or hardware
internally expects that the statistics to be collected,
in order for it to work. With this patch, the DVB core
will always retrive statistics, even if userspace doesn't
request. So, it makes the device work on all tested apps.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
The bug happens when:
CONFIG_DVB_DIB8000=m
CONFIG_DVB_USB_DIB0700=y
As a bonus, dib8000 won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with both Pixelview PV-D231 and MyGica S870.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function,
but, on dib8000, there are several exported symbols.
We need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename this function, in order to prepare for
a next patch that will add a new attach() function that
will be the only one exported by this module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
bit3 was not cleared always leaving driver reporting demod is not
fully locked. Do not check bit0 as it seems to be always 0.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add sleep ops to lgdt3304_ops to invoke lgdt3305_sleep() to be called
from dvb_frontend_suspend(). lgdt3305_soft_reset() is called for both
3304 and 3305 devices. soft_reset and sleep touch LGDT3305_GEN_CTRL_3
on 3304 and 3305 devices. Hence, adding sleep to lgdt3304_ops will help
suspend 3304 properly from dvb_frontend_suspend().
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Kconfig entry for "Micronas DRX-J demodulator" defaults to modular
if DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, because MEDIA_SUBDRV_AUTOSELECT's logic is the opposite of
the former logic.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fix the following warnings:
m88rs2000.c:300:16: warning: symbol 'm88rs2000_setup' was not declared. Should it be static?
m88rs2000.c:318:16: warning: symbol 'm88rs2000_shutdown' was not declared. Should it be static?
m88rs2000.c:328:16: warning: symbol 'fe_reset' was not declared. Should it be static?
m88rs2000.c:366:16: warning: symbol 'fe_trigger' was not declared. Should it be static?
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Band switching didn't worked always reliably as there was one
register bit set wrong.
Thanks to Robert Schlabbach for pointing this bug and solution.
Reported-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting functions for hardware filter is a bad idea, as it
breaks compilation if:
CONFIG_DVB_USB_AF9035=y
CONFIG_DVB_AF9033=m
Because the PID filter function calls would be hardcoded at
af9035.
The same doesn't happen with af9033_attach() because the
dvb_attach() doesn't hardcode it. Instead, it dynamically
links it at runtime.
However, calling dvb_attach() multiple times is problematic,
as it increments module kref.
So, the better is to pass one parameter for the af9033 module
to fill the hardware filters, and then use it inside af9035.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement PID filter and export it via symbol.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It was possible that tuner_frequency variable, used for carrier offset
compensation, was uninitialized. That happens when tuner
.get_frequency() callback is not defined.
Currently that case is not possible as only used tuner has this callback.
Coverity CID 1166057: Uninitialized scalar variable (UNINIT)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Coverity CID 1166051: Logically dead code (DEADCODE)
TS clock calculation could be more accurate, but as it is not,
remove those unused clock speeds.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are two troubles there:
1) the bit error measure were not accumulating;
2) it was missing the bit count.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:9468:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
^
By reading the comment, it is said that BER should be calculated as:
qam_pre_rs_ber = frac_times1e6( ber_cnt, rs_bit_cnt );
Also, it makes sense to take the mantissa into account, so fix the
code to do what's commented.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that everything is set, let's enable DVBv5 stats, for
applications that support it.
DVBv3 apps will still work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just assuming that the min resolution is 1E-6,
pass both bit error and bit counts for userspace to calculate
BER. The same applies for PER, for 8VSB. It is not clear how
to get the packet count for QAM. So, for now, don't expose PER
for QAM.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the stats internally to use DVBv5. For now, it will keep
showing everything via DVBv3 API only, as the .len value were
not initialized.
That allows testing if the new stats code didn't break anything.
A latter patch will add the final bits for the DVBv5 stats to
fully work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We'll need to use this function. Restore it from the
git history.
This function will be used on the next patch.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
State is already used on other places for the state struct.
Don't use it here, to avoid troubles with latter patches.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported when compiled with W=1:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘ctrl_set_channel’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:10340:26: warning: variable ‘common_attr’ set but not used [-Wunused-but-set-variable]
struct drx_common_attr *common_attr = NULL;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:10336:6: warning: variable ‘intermediate_freq’ set but not used [-Wunused-but-set-variable]
s32 intermediate_freq = 0;
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is currently not used. However, it was meant to
be called at device release. So, add it there.
While here, remove the bad check, as reported by Dan, as
smatch warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:20041 drxj_close() warn: variable dereferenced before check 'demod' (see line 20036)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are large chunks of code at drx-j that aren't used. Most
of them are due to analog TV support. Well, just enabling them
won't make analog support work, as devices with DRX and analog
support requires an extra chip (avf4910).
We don't have drivers for it, nor the current device that uses
this frontend has support for analog TV.
So, let's just get rid of this code. If latter needed, this
patch can easily be reverted from git history.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot <fengguang.wu@intel.com>:
drivers/built-in.o: In function `em28xx_dvb_init':
em28xx-dvb.c:(.text+0x876f2c): undefined reference to `drx39xxj_attach'
That happens when CONFIG_VIDEO_EM28XX_DVB is selected, and neither
CONFIG_MEDIA_SUBDRV_AUTOSELECT or DVB_DRX39XYJ is selected.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:65: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:71: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:52: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:58: warning: Using plain integer as NULL pointer
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No functional changes, but removes a duplicate check, if
!state->type_A.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix sparse warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1039:16: sparse: symbol 'drxj_default_aud_data_g' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Delay possible I2C gate close a little bit in order to see if there
is next message coming to tuner in a sequence.
Also, export private muxed I2C adapter. That is aimed only for SDR
extension module as SDR belongs to same RTL2832 physical I2C bus (it
is physically property of RTL2832, whilst it is own kernel module).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was a deadlock between master I2C adapter and muxed I2C
adapter. Implement two I2C muxed I2C adapters and leave master
alone, just only for offering I2C adapter for these mux adapters.
Reported-by: Luis Alves <ljalvs@gmail.com>
Reported-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 provides gated / repeater I2C adapter for tuner.
Implement it as a muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of those were reported by checkpatch.pl...
debug module parameter is not used anywhere so remove it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All used tuners has get_if_frequency() callback and that parameter
is not needed and will not needed as all upcoming tuner drivers
should implement get_if_frequency().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, there's just one device using this frontend: PCTV 80e,
and it works on serial mode.
Change the default here to serial mode. If we add more devices,
then this option should be set via config structure.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The cfg_mpeg_output has more fields than what it is initialized
when the code is called. Be sure to initialize everything before
use, in order to avoid random behaviors.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the windows driver, disable OOB after setting the driver
version.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DJH_DEBUG only code path in drxbsp_i2c_write_read() dereferences
w_dev_addr and subsequently w_dev_addr->user_data->i2c which results
in failure during boot. This patch fixes the null pointer derefence
bug as well as the following compile errors:
LD arch/x86/built-in.o
CC drivers/media/dvb-frontends/drx39xyj/drxj.o
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxbsp_i2c_write_read’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:25: error: redeclaration of ‘state’ with no linkage
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1512:25: note: previous declaration of ‘state’ was here
struct drx39xxj_state *state;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1560:17: error: redeclaration of ‘msg’ with no linkage
struct i2c_msg msg[2] = {
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1513:17: note: previous declaration of ‘msg’ was here
struct i2c_msg msg[2];
^
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mimic what windows driver does here: it writes 0x07 to
SIO_CC_SOFT_RST__A, instead of just 0x03.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As drxj_close puts the device in powerdown, we need to power it up
properly at drxj_open.
This is the behavior noticed at the Windows driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are no other I2C masters here. Also, the Windows driver uses
this mode (and both drxd and drxk Kernel drivers). So, switch
to it.
That helps to compare the logs between the Linux driver and the
Windows one.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just disabling the LNA every time, allow to control it from
userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On several places, the I2C functions are just wrappers to others.
Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This struct contains the first abstraction layer for the I2C
access routines. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains an abstract layer for the I2C transfer
functions. Get rid of it, merging it at drxj. This will allow
to remove another abstraction layer there, making the code
easier to read, and removing the functions that just return
-EIO.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reorder functions and data at drx_dap_fasi.c, in order to avoid
having function prototypes.
This is in preparation to merge this code inside drxj, removing
some duplicated bits there, and getting rid of yet another
abstraction layer.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is not used anywere. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
QAM/256 currently doesn't work, as the code is only called if
channel->mirror is DRX_MIRROR_AUTO, but a prevous if prevents
this condition to happen.
While here, returns -EINVAL to not supported QAM modes and
simplify the code, reducing the number of indents.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those struct data aren't used anymore. Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Checking if a time is after another one can have issues, as
times are generally u32 wide.
Use the proper macros for that at scu_command().
It should be noticed that other places also use jiffies
calculus on an improper way. This should be fixed too,
but the logic there is more complex. So, let's do it in
separate patches.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modulation and other parameters might have changed. So, better
to call ctrl_set_standard() even if the device is already
powered.
That helps to put the device into a sane state, if something
got wrong on a previous set_frontend call.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When switching from one video standard to another one,
power_down_vsb is called twice. Well, as the device is already
in power_down mode, the second call always fail. This causes that
any subsequent frontend set to fail as well:
[145074.501243] drx39xyj:power_down_vsb: called
[145089.195396] drx39xyj:power_down_vsb: error -5
[145089.195404] drx39xyj:ctrl_set_standard: error -5
[145089.195417] drx39xyj:drx39xxj_set_frontend: Failed to set standard! result=fffffffb
[145089.195470] drx39xyj:ctrl_sig_quality: error -5
[145089.195473] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195475] drx39xyj:ctrl_sig_quality: error -5
[145089.195477] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195479] drx39xyj:ctrl_sig_quality: error -5
[145089.195480] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195482] drx39xyj:ctrl_sig_quality: error -5
[145089.195484] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145089.195498] drx39xyj:ctrl_sig_quality: error -5
[145089.195500] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195502] drx39xyj:ctrl_sig_quality: error -5
[145089.195503] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195505] drx39xyj:ctrl_sig_quality: error -5
[145089.195506] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195508] drx39xyj:ctrl_sig_quality: error -5
[145089.195510] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196291] drx39xyj:drx39xxj_read_status: drx39xxj: could not get lock status!
[145090.196508] drx39xyj:ctrl_sig_quality: error -5
[145090.196511] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196514] drx39xyj:ctrl_sig_quality: error -5
[145090.196515] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196518] drx39xyj:ctrl_sig_quality: error -5
[145090.196519] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196522] drx39xyj:ctrl_sig_quality: error -5
[145090.196523] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196553] drx39xyj:ctrl_sig_quality: error -5
[145090.196554] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196557] drx39xyj:ctrl_sig_quality: error -5
[145090.196558] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196560] drx39xyj:ctrl_sig_quality: error -5
[145090.196562] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196564] drx39xyj:ctrl_sig_quality: error -5
[145090.196565] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145091.119265] drx39xyj:ctrl_sig_quality: error -5
[145091.119271] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145091.119274] drx39xyj:ctrl_sig_quality: error -5
[145091.119276] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145091.119278] drx39xyj:ctrl_sig_quality: error -5
[145091.119280] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145091.119282] drx39xyj:ctrl_sig_quality: error -5
[145091.119283] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just hardcoding an IF value of 5MHz, use the one
provided by the tuner, with can be different for QAM and
VSB.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those functions will never be used with Linux DVB binding.
Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file does an ugly binding between drxj and DVB frontend.
Remove most of the functions there. We still need to get rid of
get_frequency and set_frequency, but such patch is a little more
complex, as it should also remove some previous tuner bindings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to avoid warnings and to remove dead code, remove
the functions that don't make sense to happen, while commenting
the others that might still be useful some day.
That reduced a lot the text size:
Before:
text data bss dec hex filename
58419 2916 4 61339 ef9b drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
After:
text data bss dec hex filename
78331 2916 4 81251 13d63 drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
Without any functional changes.
It could be make sense latter to remove those drivers or to
move them into an analog-specific part of the driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With this change, we finally got rid of all abstraction
layers on this driver.
This patch also fixes the LNA GPIO settings, as the original
code were using a wrong control name for it.
This patch exposes the several functions that aren't used.
Some of them are related to analog demod that might be
used some day, but others will likely never be needed, as
they don't fit on Linux media APIs.
Latter patches will clean up this mess.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While drxj is already too big, moving the code there will
make easier to get rid of the drxj_ctrl function.
It will also help to detect and remove the unused functions,
helping to remove lots of dead code there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of drx_open and drx_close, as those are just wrapper
functions to drxj_open/drxj_close.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is used only as an abstraction layer to call the
two firmware functions. Remove it.
As a bonus, the drx_ctrl_function is now unused and can be
removed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the duplicated firmware upload code that was commented
inside drxj.c.
This code is not used, and will not work anyway, as it doesn't
download the firmware from userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The version is initialized with zero at drx_driver.c. Keep it,
in order to avoid the risk of causing any regression.
While here, remove the drx_driver.h from drxj, as this is not
required there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains just the firmware load code, that it is also
somewhat duplicated at drxj.c.
Move the code into there. Latter patches will remove the
duplicated code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to prepare to get rid of drx_driver.c, prepend all functions
there with drx_.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is mostly CodingStyle fixes and improvements.
No functional changes.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ClearQAM is currently not working. Add support for it too.
Unlikely other ATSC tuners, though, this device will not
auto-detect between ATSC and ClearQAM. So, the delivery
system should be properly set.
Also, this frontend seems to also support DVB-C annex A/C. Add
experimental support for them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Without this fixup, the DRX-J will not be properly initialized,
loosing several PIDs.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of handling endiannes with its own internal way, use the
already existing macros.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several drx-j code there that are never used, as
they don't even fit into Linux DVB subystem model.
Remove them, in order to simplify the code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The firmware upload routine is already complex enough. Split the
first loop that verifies the firmware size into a separate routine,
making the code more readable.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of hardcoding the firmware files together with the driver,
use request_firmware() way, loading it from userspace.
The firmware files are placed at:
http://linuxtv.org/downloads/firmware/#8
And they'll be latter submitted to linux-firmware git tree.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The state struct is allocated without cleaning the memory.
This causes random bugs.
Clean it, and move the memcpy functions just below each kalloc,
to be clearer that all those data are properly filled.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are memory leaks on both DVB release and
dvb attach error path. Fix them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This var is not used. Remove it from the code, as we'll now be
converting the driver to load the firmware from an external
file.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is empty (actually, all commented there). So, remove it.
We should latter remove those macros too, or convert them into
a struct to allow dynamically enable the options during device
probing time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of another typedef defined on this driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using printk's, use the pr_foo() macros.
That fixes some checkpatch warnings and provide a better error,
warning and debug support.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of defining its own set of error codes, use the linux
native ones.
Please note that this patch made a "stupid" error code mapping, just
replacing the codes with the closest one. In special, -EIO is being
used on several places. I'm pretty sure this could be better assigned,
but a change like that would require lots o time and efforts, without
much benefit.
So lets do adjstments at the error codes latter, when we have more
time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix almost all checkpatch.pl warnings/errors on drxj.c, except for:
- 80 cols whitespacing;
- too many leading tabs;
- a false positive at DRXJ_16TO8() macro.
- static char array declaration should probably be static const char
as adding "const" would cause warnings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove three typedefs from drxj.c, using the following script:
use File::Find;
use strict;
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
# This replaces the typedef declaration for a simple struct declaration - style 1
# This replaces the typedef declaration for a simple struct declaration - style 2
# Replace struct occurrences
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't need to test boolean x == true or x == false.
That makes the code more compact.
patch generated with make coccicheck and manually reviewed.
While here, remove uneeded ';'.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CodingStyle fix: don't use parenthesis on return, as it is not
a function.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_scu_atomic_read_reg16’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u16) (buf[0] + (buf[1] << 8));
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_atomic_read_reg32.isra.59’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:2186:7: warning: ‘*((void *)&buf+3)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u32) buf[3];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2188:10: warning: ‘*((void *)&buf+2)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[2];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2190:10: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[1];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2192:10: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[0];
^
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This were fixed with the help of this small perl script:
#!/usr/bin/perl
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Some manual work were needed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the changes were done with scripts like:
for i in drivers/media/dvb-frontends/drx39xyj/*.[ch]; do perl -ne '$var = "drx_sig_quality"; s,\b($var)_t\s+,struct \1 ,g; s,\bp_*($var)_t\s+,struct \1 *,g; s,\b($var)_t\b,struct \1,g; s,\bp_*($var)_t\b,struct \1 *,g; print $_' <$i >a && mv a $i; done
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is not used anywhere. Drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
None of those vars are used on those functions. Just remove them.
After this patch, there's just one of such warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:7872:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
We'll keep it, as BER count will be useful when converting the
frontend to report statistics via DVBv5 API
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is not static. Also, it is not used anywhere.
So, drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This time, use checkpatch --strict --fix.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no reason at all to use CamelCase here. Convert all of
them to normal case.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of manually fixing the issues, use the --fix experimental
checkpatch. That solves a bunch of checkpatch issues.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch generated with this script:
for i in drivers/media/dvb-frontends/drx39xyj/*.[ch]; do perl -ne 's,(enum|struct|void|int|u32|u64|u16|u8|s8|s16|s32|s64)\s+(\S+)\s+\*[ ]+,\1 \2 *,g; print $_' <$i >a && mv a $i; done
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are lots of typedefs there. Let's get rid of them.
Most of the work here is due to this small script:
if [ "$3" == "" ]; then
echo "usage: $0 type DRXName drx_name"
fi
t=$1; f=$2; g=$3
for i in *.[ch]; do
sed s,"p${f}_t","$t $g *",g <$i >a && mv a $i && \
sed s,"${f}_t","$t $g",g <$i >a && mv a $i
done
Just kept there the function typedefs, as those are still useful.
Yet, all those tuner_ops can likely be just removed on a latter
cleanup patch.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move them into drx_driver.h
That makes easier to cleanup further what's there at the
headers.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the work were done by those small scripts:
for i in *; do sed s,pDRXFrequency_t,"s32 *",g <$i >a && mv a $i; done
for i in *; do sed s,DRXFrequency_t,"s32",g <$i >a && mv a $i; done
for i in *; do sed s,pDRXSymbolrate_t,"u32 *",g <$i >a && mv a $i; done
for i in *; do sed s,DRXSymbolrate_t,"u32",g <$i >a && mv a $i; done
for i in *; do sed s,FALSE,false,g <$i >a && mv a $i; done
for i in *; do sed s,TRUE,true,g <$i >a && mv a $i; done
for i in *; do sed s,Bool_t,bool,g <$i >a && mv a $i; done
for i in *; do sed s,pbool,"bool *",g <$i >a && mv a $i; done
The only remaining things there are the return values.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch created using this small script:
for j in 8 16 32; do for i in *; do sed s,pu${j}_t,"u$j *",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,ps${j}_t,"s$j *",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,s${j}_t,"s$j",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,u${j}_t,"u$j",g <$i >a && mv a $i; done; done
and fixing the bsp_types.h header.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
