The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 7cbeb2e1bf ("media: smiapp: Move definitions under driver
directory") moved the definitions in include/media/i2c/smiapp.h into other
files and removed include/media/i2c/smiapp.h.
Since then, ./scripts/get_maintainer.pl --self-test complains:
warning: no file matches F: include/media/i2c/smiapp.h
Remove MAINTAINER file entry to this removed file and while at it, update
Sakari's email address in this section.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add entry for my @iki.fi e-mail address to the mailmap.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, imgu is working on 450MHz for all cases, however
in some cases (input frame less than 2048x1152), the imgu
did not need work in high frequency.
This patch make imgu work on 200MHz if the imgu input
frame is less than 2048x1152 to save power.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.
Change this by brinting the register values hex formatted and the states
as more readable string.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.
Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document the optional binding to limit the possible sdtv standards on the
input connectors.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use underlines to highlight optional and required properties. This is
quite common for all bindings. Align descriptions and start sentence
with uppercase letter. Also reword the usage of the required
endpoint properties for the output port in case BT.656 should be used.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.
This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As documented in [1] the runtime-pm ops are used to set the device into
a fully 'workable' state. Therefore it can be used to enable or disable
the irqs.
[1] https://www.kernel.org/doc/html/latest/power/runtime_pm.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.
Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is
no way to try different selections. The patch adds a helper function to
select the correct selection memory space (sub-device file handle or
driver state) which will be set/returned.
The selection rectangle is updated if the format is FORMAT_ACTIVE and
the rectangle position and/or size differs from the current set
rectangle.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently a local copy of sel->r is made and adapted to the hardware
constraints. After the adaption the value is applied to the hardware but
the driver forgot to reflect the adapted value to the user space.
Drop the local copy and work directly on the requested rectangle
instead to fix this.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TVP5150/1 decoders support different video input sources to their
AIP1A/B pins.
Possible configurations are as follows:
- Analog Composite signal connected to AIP1A.
- Analog Composite signal connected to AIP1B.
- Analog S-Video Y (luminance) and C (chrominance)
signals connected to AIP1A and AIP1B respectively.
This patch extends the device tree bindings documentation to describe
how the input connectors for these devices should be defined in a DT.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds the of_graph support to describe the tvp input connections.
Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result
of discussion [1],[2] the device-tree maps these ports 1:1. Look at the
Documentation for more information. Since the TVP5150 is a converter/bridge
the device-tree must contain at least 1-input and 1-output port. The
mc-connectors and mc-links are only created if the device-tree contains the
corresponding connector nodes. If more than one connector is available the
media_entity_operations.link_setup() callback ensures that only one
connector is active.
[1] https://www.spinics.net/lists/linux-media/msg138545.html
[2] https://www.spinics.net/lists/linux-media/msg138546.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit f7b4b54e63 ("[media] tvp5150: add HW input connectors support")
added input signals support for the tvp5150, but the approach was found
to be incorrect so the corresponding DT binding commit 82c2ffeb21
("[media] tvp5150: document input connectors DT bindings") was reverted.
This left the driver with an undocumented (and wrong) DT parsing logic,
so lets get rid of this code as well until the input connectors support
is implemented properly.
It's a partial revert due other patches added on top of mentioned commit
not allowing the commit to be reverted cleanly anymore. But all the code
related to the DT parsing logic and input entities creation are removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The patch adds the initial connector parsing code, so we can move from a
driver specific parsing code to a generic one. Currently only the
generic fields and the analog-connector specific fields are parsed. Parsing
the other connector specific fields can be added by a simple callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[hverkuil-cisco@xs4all.nl: replace ; with break; in a empty case]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently every driver needs to parse the connector endpoints by it self.
This is the initial work to make this generic. A generic connector has
common members and connector specific members. The common members are:
- type
- label (optional)
- links
- nr_of_links
The specific members are stored within a union, since only one of them
can be available at the time. Since this is the initial support the
patch adds only the analog-connector specific ones.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A link is between two endpoints not between two ports to be more
precise. Add the local_id/remote_id field which stores the endpoint
reg/port property to the link. Now the link holds all necessary
information about a link.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This helper was introduced before those helpers where awailable. Convert
it to cleanup the code and improbe readability.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver differentiate the port number property handling for
ACPI and DT. This is wrong as because ACPI should use the "reg" val too
[1].
[1] https://patchwork.kernel.org/patch/11421985/
Fixes: ca50c197bd ("[media] v4l: fwnode: Support generic fwnode for parsing standardised properties")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since we expose the definition to the dt-bindings we need to keep those
definitions in sync. To address this the patch adds a simple cross
reference to the dt-bindings.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add defines which can be included to easily describe the supported
standard tv norms 'sdtv-standards' within the device tree.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some connectors no matter if in- or output supports only a limited
range of sdtv standards. It doesn't matter if the hardware behind that
connector supports more than the listed formats since the users are
restriced by a label e.g. to plug only a camera into this connector
which uses the PAL format.
This patch adds the capability to describe such limitation within the
firmware. There are no format restrictions if the property isn't
present, so it's completely backward compatible.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling ccdc_data_size_max_bit() to validate data_sz in
vpfe_ccdc_validate_param(), it's treated as an enumeration ranging from
0 to 7 while essentially it's an 32 bit unsigned integer directly from
user space. This can make the return value of ccdc_data_size_max_bit()
underflow and bypass the following check.
To fix this, an additional check is added to the following if clause to
keep this enumaration variable in range. And if its value is not legal,
return -EINVAL properly.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.
This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().
In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.
So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Previously, vpu->recv_buf and send_buf are forced cast from
void __iomem *tcm. vpu->recv_buf->share_buf is passed to
vpu_ipi_desc.handler(). It's not able to do unaligned access. Otherwise
kernel would crash due to unable to handle kernel paging request.
struct vpu_run {
u32 signaled;
char fw_ver[VPU_FW_VER_LEN];
unsigned int dec_capability;
unsigned int enc_capability;
wait_queue_head_t wq;
};
fw_ver starts at 4 byte boundary. If system enables
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS, strscpy() will do
read_word_at_a_time(), which tries to read 8-byte: *(unsigned long *)addr
vpu_init_ipi_handler() calls strscpy(), which would lead to crash.
vpu_init_ipi_handler() and several other handlers (eg.
vpu_dec_ipi_handler) only do read access to this data, so they can be
const, and we can use memcpy_fromio() to copy the buf to another non iomem
buffer then pass to handler.
Fixes: 85709cbf15 ("media: replace strncpy() by strscpy()")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add encoder control for enabling/disabling frame rate control via
V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE. It is enabled by default.
Signed-off-by: Jeffrey Kardatzke <jkardatzke@google.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes the following smatch warning in the error path:
drivers/media/platform/qcom/venus/vdec.c:968 vdec_start_streaming()
warn: inconsistent returns 'mutex:&inst->lock'.
Locked on: line 952
Unlocked on: line 963
line 968
by goto mutex unlock.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The variable gate is being initialized and also checked and re-assigned
with values that are never read as it is being re-assigned later in a
for-loop with a new value. The assignments are redundant and can be
removed.
Addresses Coverity ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 267897a470 ("[media] tda10071: implement DVBv5 statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is required to support the Terratec S2 USB Box Revision 4, which
reused usb vid:pid, but has a different demodulator (m88ds3103b) at
i2c address 0x6a.
[fixed checkpatch issues]
Signed-off-by: Michael Bunk <micha@freedict.org>
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hauppauge 461e rev2 is a DVB-S/S2 usb device containing:
- m88ds3103b demod
- ts2022 tuner
- A8293 SEC
Device is the same as Hauppauge 461e,
except it contains updated m88ds3103b demod.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ds3103b demodulator identifies as an m88rs600, but requires different
clock settings and firmware, along with differences in register settings.
Changes were reverse engineered using an instrumented downstream GPLv2
driver to compare i2c traffic and clocking. The mclk functions are from
the downstream GPLv2 driver.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are many protocols that encode more than 32 bit. We want 64 bit
support so that BPF IR decoders can decode more than 32 bit. None of
the existing kernel IR decoders/encoders support 64 bit, for now.
The MSC_SCAN event can only contain 32 bit scancodes, so we only generate
MSC_SCAN events if the scancode fits into 32 bits. The full 64 bit
scancode can be read from the lirc chardev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This adds VP9 decoding for the Amlogic GXL, G12A & SM1 SoCs, using
the commong "HEVC" HW decoder.
For G12A & SM1, it uses the IOMMU support from the firmware.
For 10bit decoding, the firmware can only decode in the proprietary
Amlogic Framebuffer Compression format, but can output in 8bit NV12
buffer while writing the decoded frame.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Amlogic VP9 decoder requires an additional 16-byte payload before every
frame header.
The source buffer is updated in-place, then given to the Parser FIFO DMA.
The FIFO DMA copies the blocks into the 16MiB parser ring buffer, then parses
and copies the slice into the decoder "workspace".
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the HEVC & VP9 common decoder support, handling
Amlogic GXBB, GXL, G12A and SM1 platforms.
This handles the "HEVC" hw decoder used for HEVC and VP9, and will be
using in the new H264 multi-instance decoder for G12A & SM1 platforms.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add helpers to support the lossless framebuffer compression format that
will be used in HEVC & VP9 decoders when decoding 10bit content for
downsampling to 8bit NV12 and later proper compressed buffer support.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HEVC/VP9 aligns the plane stride on 32, so align the planes stride
for all codecs to 32 to satisfy HEVC/VP9 decoding using the "HEVC" HW.
This fixes VP9 decoding of streams with following (not limited) widths:
- 264
-288
- 350
- 352
- 472
- 480
- 528
- 600
- 720
- 800
- 848
- 1440
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the H264 compressed format (V4L2_PIX_FMT_H264).
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add all the necessary bits to pass v4l2-compliance in stateful decoding
mode.
Mostly includes tracking the state of the decoder, allowing the OUTPUT
queue to stream while the CAPTURE queue is inactive, handling resolution
change events, draining with V4L2_DEC_CMD_STOP, copying more metadata
from the src buffers to the dst buffers, etc.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the previously introduced v4l2-mem2mem core APIs to handle the drainig,
stopped and next-buf-is-last states.
With these changes, the v4l2-compliance still passes with the following
commands :
>>>><><><><><><><><><><><><><><><><>< 15.53 fps
15.53 fps
><><><><><><><><><><><><>< 13.99 fps
13.99 fps
><><><><><><><><><><><>< 13.52 fps
13.52 fps
><><><><><><><><><><><><>< 13.41 fps
13.41 fps
><><><><><><><><><><><><>< 13.21 fps
13.21 fps
><><><><><><><><><><><>< 13.09 fps
13.09 fps
><><><><><><><
STOP ENCODER
<<<
EOS EVENT
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video0: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [1]
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video1: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [2]
No functional changes should be noticed.
[1] https://termbin.com/25nn
[2] https://termbin.com/dza4
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since the draining and stop phase of the HW decoder mem2mem bahaviour is
now clearly defined, we can move handling of the following states to the
common v4l2-mem2mem core code:
- draining
- stopped
- next-buf-is-last
By introducing the following v4l2-mem2mem APIs:
- v4l2_m2m_encoder_cmd/v4l2_m2m_ioctl_encoder_cmd to handle start/stop command
- v4l2_m2m_decoder_cmd/v4l2_m2m_ioctl_decoder_cmd to handle start/stop command
- v4l2_m2m_update_start_streaming_state to update state on start of streaming
of the de/encoder queue
- v4l2_m2m_update_stop_streaming_state to update state on stop of streaming
of the de/encoder queue
- v4l2_m2m_last_buffer_done to make the current dest buffer as the last one
And inline helpers:
- v4l2_m2m_mark_stopped to mark the de/encoding process as stopped
- v4l2_m2m_clear_state to clear the de/encoding state
- v4l2_m2m_dst_buf_is_last to detect the current dequeued dst_buf is the last
- v4l2_m2m_has_stopped to detect the de/encoding stopped state
- v4l2_m2m_is_last_draining_src_buf to detect the current source buffer should
be the last processing before stopping the de/encoding process
The special next-buf-is-last when min_buffers != 1 case is also handled
in v4l2_m2m_qbuf() by reusing the other introduced APIs.
This state management has been stolen from the vicodec implementation,
and is no-op for drivers not calling the v4l2_m2m_encoder_cmd or
v4l2_m2m_decoder_cmd and v4l2_m2m_update_start/stop_streaming_state.
The vicodec will be the first one to be converted as an example.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
