Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi channel context (AP + STA case), adjust the TSF time of
the AP chanctx to keep its beacons at half beacon interval offset
relative to the STA chanctx.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update current offchannel duration during scan or roc request.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a basic state machine for switch channel context
for beacon transmission.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save TSF in channel context for multiple operating channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrieve appropriate operating channel context while switching
between operating and off channels.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add channel context operations (add, remove, change, assign and
unassign) to enable support for multiple channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add remain on channel support in order to enable multi-channel
concurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement hw_scan support for enabling multi-channel cuncurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving from or entering to active channel context, send out
nullfunc frame to inform to the AP about the presence of station.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force queueing of all frames that belong to a virtual interface on
a different channel context, to ensure that they are sent on the
correct channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context worker is used to switch to next requested
channel context.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to maintain per-channel ACs list.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context structure is defined to enable
multi-channel concurrency support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since CL_PRINTF only ever takes a single argument, make sure a format
string cannot leak into printk.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rsi_module_init() to propagate sdio_register_driver() errors.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
module_usb_driver eliminates the boilerplate and makes the code simpler,
in addition to the fact currently rsi_module_init() ignores usb_deregister() error.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For users who do not need wowlan, load mwifiex.ko with
disconnect_on_suspend = 1; or iw phy0 wowlan disable.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When magic-packet is generated as a UDP packet the offset should
be 20+8 more bytes to cover IPv4 header and UDP header. So the
total offset become 56.
Add a new MEF entry to support both magic-packet patterns
generated by different tools.
Cc: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Zhiyuan Yang <yangzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've here a device detected as:
bcma: bus0: Found chip with id 0xD144, rev 0x01 and package 0x08
I couldn't find GPIO handling hw button until trying GPIO 20. It seems
BCM53572 also has 32 GPIOs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We setup BCN_OFFSET{0,1} registers dynamically, don't have to
initialize them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no beaconing is needed, first stop beacon queue (disable beaconing
globally) to avoid possible sending of not prepared beacon on short
period after clearing beacon and before stop of BCN queue.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We setup MAC_BSSID_DW1_BSS_BCN_NUM dynamically when numbers of active
beacons increase. Change default to 0 to tell hardware that we want to
send only one beacon as default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Matthias, on 5572 chip, even if we clear up TXWI
of corresponding beacon, hardware still try to send it or do other
action that increase power consumption peak up to 1A.
To avoid the issue, setup beaconing dynamically by configuring offsets
of currently active beacons and MAC_BSSID_DW1_BSS_BCN_NUM variable,
which limit number of beacons that hardware will try to send.
Reported-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is needed for further changes to keep global variables
consistent when changing beaconing on diffrent vif's.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A custom regulatory domain was introduced in this commit:
cc0ba0d mwifiex: support custom world regulatory domain
The commit description says that it was introduced because the world
regulatory domain does not include channels 52-64 and 100-140. These
channels are described in the world regulatory domain now, so we can
drop this custom regulatory domain.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a risk that the variables will be used without being initialized.
Have also moved variable to the part of the code where it is used.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Band switching code needs to know what channel we switch to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY may need to be re-initialized during runtime (e.g. on band switch).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is tiny optimization and grouping band/channel ops.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There aren't devices with multiple 802.11 cores supported by b43.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was never used, b43_switch_channel is always called with hw_value
(from mac80211) or whatever get_default_chan returns.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX descriptor data must be read only if the descriptor has been fully
updated by HW.
There is a "ownership" flag in the descriptor itself to test this.
The driver code contains a read for the "ownership" flag and, after
it, other read access for descriptor data.
This is in DMA coherent memory, that is _not_ guaranteed to be immune
to instruction reordering, thus it is possible that the descriptor
data is read _before_ the "ownership" flag.
This can theoretically lead to a DMA/CPU race that may end up with the
driver reading the data when it is still not valid, and the "ownership"
bit just after enough time that the HW make the whole descriptor valid.
The driver will in this case believe the data is valid, but it will use
the invalid data read earlier.
In order to avoid this, this patch adds a rmb() to force the "ownership"
bit read to be issued before other descriptor data reads are attempted.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the driver report signal information for rtl8185
boards using dBm instead of unspecified unit.
Rtl8180 remains untouched.
I did some tests to confirm the correctness of the measure performed
by the board and it seems reasonably correct.
The test setup has been made by connecting an AP with coax and
RF attenuators to the card antenna port.
In order to get a reference measure I tried with several cards with
different chipset I own. I found that many gave different results, and
I finally selected two cards that gave me consistent results to use
as reference: AR9271 and Prism54-usb (isl3887 with Frisbee radio).
Using this references I compared the RSSI information with my rtl8185
and I repeated tests with three different attenuation values, increasing
attenuation by 10dB each step.
I made only relative measures, making NO assumption about source power.
CCK measures seem very close to my references, OFDM are a little bit
less precise but, considering that these cards are not measuring
instrumentation, IMHO this is still fairly good.
CCK measures (1Mbps beacons)
ATTENUATOR 1
p54usb: -58dBm
ath9k_htc: -59dBm
rtl8185: -59dBm
ATTENUATOR 2
p54usb: -67dBm
ath9k_htc: -68dBm
rtl8185: -70dBm
ATTENUATOR 3
p54usb: -78dBm
ath9k_htc: -79dBm
rtl8185: -79dBm
OFDM measures (54Mbps ping)
ATTENUATOR 1
p54usb: -58dBm
ath9k_htc: -57dBm
rtl8185: -62dBm
ATTENUATOR 2
p54usb: -68dBm
rtl8185: -71dBm
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove the if-else chains and use switch-case to make code more
readable and avoiding long lines that broke in several lines
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
