The MIPSsim platform is no longer supported or used.
[ralf@linux-mips.org: Also remove mipssim from arch/mips/Kbuild.platforms
and delete arch/mips/include/asm/mach-mipssim/*.]
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If it's set, SIGPENDING is also set. And SIGPENDING is present in
the masks...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No need to keep 4 copies of that stuff; merged and taken to
entry.S, unused public symbols there killed off.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
YAMON requires and enforces the RTC Data Mode (Register B, DM bit) to
binary, that is the bit is set every time the board goes through the
firmware bootstrap sequence. Likewise its calendar manipulation commands
interpret or set the RTC registers unconditionally as binary, never
actually checking what the value of the DM bit is, under the (correct)
assumption that it has been previously set, to indicate the binary mode.
A change to Linux a while ago however introduced a platform-specific
tweak that clears that bit and therefore forces the data mode to BCD.
This causes clock corruption and misinterpretation that has to be fixed up
by user-mode tools in system startup scripts as the initial clock is often
incorrect according to the BCD interpretation forced.
This change removes the hack; a comment included refers to alarm code,
but even if it was broken at one point by requiring the BCD mode, it
should have been trivially corrected and even if not, given how rarely the
alarm feature is used, that was not really a reasonable justification to
break the system clock that is indeed used by virtually everything. And
either way the alarm code has been since fixed anyway.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4336/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gpio_chip struct allows us to set a .to_irq callback. Once this is set
we can rely on the generic __gpio_to_irq() function to map gpio->irq allowing
more than one gpio_chip to register an interrupt
Signed-off-by: John Crispin <blogic@openwrt.org>
Implement support for pinctrl on lantiq/falcon socs. The FALCON has 5 banks
of up to 32 pins.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Implement support for pinctrl on lantiq/xway socs. The IO core found on these
socs has the registers for pinctrl, pinconf and gpio mixed up in the same
register range. As the gpio_chip handling is only a few lines, the driver also
implements the gpio functionality. This obseletes the old gpio driver that was
located in the arch/ folder.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
For CIUv1 controllers, we were relying on all calls to the irq_chip
functions to be done from the CPU that received the irq, and that they
would all be done from interrupt contest. These assumptions do not
hold for threaded handlers.
We make all the masking actually mask the irq source, and use real
raw_spin_locks instead of manually twiddling the Status[IE] bit.
Signed-off-by: David Daney <david.daney@cavium.com>
The cn68XX has a new interrupt controller named CIU2, add support for
this, and use it if cn68XX detected at runtime.
Signed-off-by: David Daney <david.daney@cavium.com>
Add support for cn68xx, cn61xx, cn63xx, cn66xx and cnf71XX.
Add little-endian register layouts.
Patch cvmx-interrupt-rsl.c for changed definition.
Signed-off-by: David Daney <david.daney@cavium.com>
Also add cvmx_get_octeon_family().
Both of these are needed by the upcoming register definition refresh
patch.
Signed-off-by: David Daney <david.daney@cavium.com>
This improves code readability, and ensures that
all resource fields will be initialized correctly.
Additionally, it helps to reduce the size of the
kernel image by using uninitialized resource
variables.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4171/
Signed-off-by: John Crispin <blogic@openwrt.org>
See commit b6999b191 which did the same modification for x86's mm/gup,
Quote from commit b6999b191:
"If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that."
[ralf@linux-mips.org: fixed rejects caused by the original patch getting
linewrapped.]
Signed-off-by: Jovi Zhang <boojovi@gmail.com>
Cc: Youquan Song <youquan.song@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/4291/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the controller has no PCIe module attached, accessing of the device
configuration space causes a data bus error. Avoid this by checking the
status of the PCIe link in advance, and indicate an error if the link
is down.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4293/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Lantiq socs have a General Purpose Timer Unit (GPTU). This driver allows us to
initialize the timers. The voice firmware needs these timers as a reference.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4236/
The xrx200 SoC family has the same PCI clock register layout as the AR9.
Enable the same quirk as for AR9
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4235/
As a result of a non populated ->bits field inside the clock struct, the clock
domains were never powered on the Falcon. Until now we only used domains that
were also used and powered by the bootloader.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4234/
Register nmi and ejtag bootrom vectors for FALC-ON SoC.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4238/
Support for the external interrupt unit was broken when the code was converted
to devicetree support.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4231/
The SVIP SoC has its timer IRQ on a different IRQ than 7. Fix up the irq
code to be able to handle this.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4229/
Up to now all our SoCs had the 5 IM ranges in a consecutive order. To accomodate
the SVIP we need to support IM ranges that are scattered inside the register range.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4237/
2ec8663f9c03a96f2c328c7c483603c31d62ad37 (lmo) rsp.
497e5ff03f (kernel.org) [MIPS: Malta: Move
PIIX4 PCI fixup to where it belongs.] attempted to move this PCI fixup
but really only added it at it's new location without deleting the old
instance.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ath79 platform code allows to run a single kernel image on various
SoCs which are based on the 24Kc and 74Kc cores. The current code
explicitely disables the DSP ASE, but that is available in the 74Kc core.
Remove the override in order to let the kernel to detect the availability
of the DSP ASE at runtime.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current implementation of synchronise_count_{master,slave} blocks
slave CPUs in early boot until all of them come up. This no longer
works because blocking a CPU with interrupts off after notifying the
CPU to be online causes problems with the current kernel.
Specifically, after the workqueue changes
(commit a08489c569 "Pull workqueue changes from Tejun Heo")
the CPU_ONLINE notification callback workqueue_cpu_up_callback()
will hang on wait_for_completion(&idle_rebind.done), if the slave
CPUs are blocked for synchronize_count_slave().
The changes are to update synchronize_count_{master,slave}() to handle
one CPU at a time and to call synchronise_count_master() in __cpu_up()
so that the CPU_ONLINE notification goes out only after the COP0 COUNT
register is synchronized.
[ralf@linux-mips.org: This matter only to those few platforms which are
using the cp0 counter as their clocksource which are XLP, XLR and MIPS'
CMP solution.]
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In case a series of R_MIPS_HI16 relocations was not followed by an
R_MIPS_LO16 relocation we were leaking the hi16 relocation chain.
Handle that error and return an error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace. In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore. Fix race by moving it into
mod_arch_specific.
[ralf@linux-mips.org: folded in Tony's followup fix. Thanks Tony!]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/4189/
Commit 6f5d2e970452b5c86906adcb8e7ad246f535ba39 (lmo) /
477c4b0740 (kernel.org) [[MIPS: VPE: Free
relocation chain on error.] fixed the same issue in the vpe loader in 2009
but back then the same bug in module.c went unfixed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Akhilesh Kumar <akhilesh.lxr@gmail.com>
Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is needed in order to get rid of the following errors:
arch/mips/ath79/clock.c:353:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/ath79/clock.c:377:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/ath79/clock.c:383:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/ath79/clock.c:388:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/ath79/clock.c:394:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4170/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The currently assigned IRQ number to the OHCI controller is incorrect for
the AR7240 SoC, and that leads to the following error message from the
OHCI driver:
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ath79-ohci ath79-ohci: Atheros built-in OHCI controller
ath79-ohci ath79-ohci: new USB bus registered, assigned bus number 1
ath79-ohci ath79-ohci: irq 14, io mem 0x1b000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new full-speed USB device number 2 using ath79-ohci
ath79-ohci ath79-ohci: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Fix this by using the correct IRQ number.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 3.6.0-rc1, We are getting many messages like:
WARNING: at kernel/irq/irqdomain.c:444 irq_domain_associate_many+0x23c/0x260()
Modules linked in:
Call Trace:
[<ffffffff814cb698>] dump_stack+0x8/0x34
[<ffffffff81133d00>] warn_slowpath_common+0x78/0xa8
[<ffffffff81187e44>] irq_domain_associate_many+0x23c/0x260
[<ffffffff81187f38>] irq_create_mapping+0xd0/0x220
[<ffffffff81188104>] irq_create_of_mapping+0x7c/0x158
[<ffffffff813e5f08>] irq_of_parse_and_map+0x28/0x40
.
.
.
Both the CIU and GPIO interrupt domains were somewhat screwed up.
For the CIU domain, we need to call irq_domain_associate() for each of
the preassigned irq numbers. For the GPIO domain, we were applying
the register bit offset in octeon_irq_gpio_xlat, but it should be done
in octeon_irq_gpio_map instead.
Also: Reserve all 8 'core' irqs for the 'core' irq_chip so that they
don't get used by the other domains. Remove unused OCTEON_IRQ_*
symbols.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"The lion share of this pull request are fixes for clk-related breakage
caused by other changes during this merge window. For some platforms
the fix was as simple as selecting HAVE_CLK, for others like the
Loongson 2 significant restructuring was required.
The remainder are changes required to get the Lantiq code to work
again."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Loongson 2: Sort out clock managment.
MIPS: Loongson 1: more clk support and add select HAVE_CLK
MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: Lantiq: Platform specific CLK fixup
MIPS: Lantiq: Add device_tree_init function
MIPS: Lantiq: Fix interface clock and PCI control register offset
