Commit Graph

602962 Commits

Author SHA1 Message Date
Bjorn Andersson
6f10b4e1e6 wcn36xx: Correct DXE chip version differentiation
The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 16:58:27 +03:00
Bjorn Andersson
05ddce497c wcn36xx: Split mmio space into explicit regions
Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 16:58:22 +03:00
Bjorn Andersson
1c41fd5fb7 wcn36xx: Change indication list lock to spinlock
In preparation for handling incoming messages from IRQ context, change
the indication list lock to a spinlock

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 16:58:18 +03:00
Bjorn Andersson
909aa60c05 wcn36xx: Fold indication payload into message header
Merge the two allocation instead of separately allocating room for the
indication payload.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 16:58:14 +03:00
Mohammed Shafi Shajakhan
ce30c4fe1a ath10k: replace warning with an error message if HTT op version is unset
Print an ath10k error message rather a call trace when HTT op version is
not found from firmware META data (IE). This should be sufficient to figure
out what went wrong.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:53:44 +03:00
Anilkumar Kolli
e565c3125e ath10k: enable support for QCA9888
QCA9888 shares the same configuration with QCA99X0
with NSS=2.

Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:50:45 +03:00
Anilkumar Kolli
2225378d84 ath10k: remove unused member in ath10k_hw_regs
rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.

Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:50:41 +03:00
Ben Greear
d0eeafad11 ath10k: Clean up peer when sta goes away.
If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:48:22 +03:00
Ben Greear
c5ace87a88 ath10k: Add WARN_ON if we over-write peer-map pointer.
Not sure this can happen, but seems like a reasonable sanity
check.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:48:17 +03:00
Eduardo Abinader
9802977dcc ath10k: remove extra space on ath10k_update_channel_list
just to comply to coding style.

Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:47:10 +03:00
Ashok Raj Nagarajan
34293f7558 ath10k: simplify pktlog htt event processing
It is expected that all pktlog events for 10.4 firmware based solutions
should come through CE8 where as in case of 10.2 firmware based solutions,
it should come through one of the HTT events (HTT_T2H_MSG_TYPE_PKTLOG).

But from experiments with 10.4 based solutions, it is observed that pktlog
event for ATH_PKTLOG_TYPE_TX_MSDU_ID is coming through HTT pktlog event.
Currently, we always parse with 10.2 pktlog header which will lead to
pktlog decoding issues (payload length mismatch exceptions)

For trace points, it is required to provide only the payload size. So
fixing this by simplifying the payload size calculation without the use of
ath10k pktlog headers.

While there, remove the unused ath10k pktlog headers.

Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:46:03 +03:00
Chaehyun Lim
a3dadad733 ath10k: remove unused <linux/semaphore.h>
<linux/semaphore.h> is not used anymore, so just remove the include.

Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:43:59 +03:00
Ben Greear
6d68f7900d ath10k: ensure peer_map references are cleaned up
While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.

Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:41:59 +03:00
Ben Greear
de0170beaa ath10k: ensure txrx-compl-task is stopped when cleaning htt-tx
Otherwise, the txrx-compl-task may access some bad memory?

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:41:55 +03:00
Mohammed Shafi Shajakhan
2ba1f37094 ath10k: remove debugfs support for Per STA total rx duration
cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics'  mac80211 callback is implemented
to extend support for per station statistics from the driver.

Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:37:51 +03:00
Mohammed Shafi Shajakhan
120a1f02a5 ath10k: add support for ath10k_sta_statistics support
Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211

This can also act as a placeholder for any new per STA stats support

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:37:47 +03:00
Mohammed Shafi Shajakhan
4a49ae94a4 ath10k: fix 10.4 extended peer stats update
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled

The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats

{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}

Fixes: f9575793d4 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08 09:36:41 +03:00
Sven Eckelmann
aaab50fcea ath9k: Fix programming of minCCA power threshold
The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.

Fixes: 3533bf6b15 ("ath9k: Fix regulatory compliance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 14:13:31 +03:00
Eduardo Abinader
0f27ac40fb ath9k: return false when reading wrong eeprom offset
Just setting the proper return for reading beyond the eeprom data.

Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 14:10:12 +03:00
Mohammed Shafi Shajakhan
3fa35bacc1 ath10k: fix some typo in spectral code commments
Found this obvious typo while going through the spectral
code design in ath10k

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 14:04:52 +03:00
Mohammed Shafi Shajakhan
34663241d8 ath10k: disable TX_STBC for tx chainmask of 1
Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 14:00:39 +03:00
Mohammed Shafi Shajakhan
343bf960f0 ath10k: enable beacon loss detection support for 10.4
Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 13:59:42 +03:00
Bob Copeland
a66cd733a7 ath10k: fix potential null dereference bugs
Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.

Fix these by making the dereference happen later.

Addresses the following smatch warnings:

drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 13:54:15 +03:00
Mohammed Shafi Shajakhan
569fba2cbb ath10k: remove unneccessary WARN_ON_ONCE in rx during ACS
The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)

	[scan channel] --> [rx channel] --> [peer channel] -->
	[vdev channel] -->  [any vdev channel] --> [target oper channel]

'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.

During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.

'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")

    WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
    [<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
    (ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
    [<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
    [<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
    [<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
    [<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
    [<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])

Fixes:3b0499e9ce42 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 13:52:23 +03:00
Mohammed Shafi Shajakhan
fb7caababc ath10k: fix crash during card removal
Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)

	ath10k_core_unregister -> ath10k_core_free_board_files

	...... device unplug spurious interrupt .........

	ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump  ...etc

Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.

Call trace:

 EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
 f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
  [<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-06-30 13:50:02 +03:00
Guy Mishol
535633a5ba wlcore: reconfigure sta rates on authorization
Since stations can now be added before association
(NL80211_FEATURE_FULL_AP_CLIENT_STATE support),
no supported rates are set when the station is added
to the fw, resulting in fw recovery.

Fix it by first configuring the AP basic rates as
the station configured rates (when the station is
first added to the driver), and after the station
was authorized re-configure it, now with the actual
supported rates.

Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 19:03:16 +03:00
Rafał Miłecki
20856adf22 brcmfmac: add missing break when deleting P2P_DEVICE
We obviously don't want to fall through in that switch. With this change
1) We wait for event (triggered by p2p_disc) as expected
2) We remove interface manually on timeout
3) We return 0 on success instead of -ENOTSUPP

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 19:01:57 +03:00
Rafał Miłecki
bda9d01427 brcmfmac: include also core.h header in cfg80211.h
This header provides two inline functions using struct brcmf_if so we
need core.h to avoid:

drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_prof’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:368:13: error: dereferencing pointer to incomplete type
  return &ifp->vif->profile;
             ^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_vif’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:374:12: error: dereferencing pointer to incomplete type
  return ifp->vif;
            ^

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 19:00:35 +03:00
Rafał Miłecki
54264e7ea0 brcmfmac: use const char * for interface name in brcmf_add_if
This function can work just fine with const pointer, it only calls
alloc_netdev which take const as well. Moreover it makes this function
more flexible as some cfg80211 callback may provide const char * as
well, e.g. add_virtual_intf. This will be needed for more advanced
interface management.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:59:59 +03:00
Rafał Miłecki
b50ddfa853 brcmfmac: fix lockup when removing P2P interface after event timeout
Removing P2P interface is handled by sending a proper request to the
firmware. On success firmware triggers an event and driver's handler
removes a matching interface.

However on event timeout we remove interface directly from the cfg80211
callback. Current code doesn't handle this case correctly as it always
assumes rtnl to be unlocked.

Fix it by adding an extra rtnl_locked parameter to functions and calling
unregister_netdevice when needed.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:57:19 +03:00
Arnd Bergmann
6f07e0f12a wireless: ipw2200: fix old-style declaration
Modern C standards expect the 'inline' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":

drivers/net/wireless/intel/ipw2x00/ipw2200.c:4096:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:56:21 +03:00
Arnd Bergmann
2a063835ce wireless: brcmsmac: fix old-style declaration
Modern C standards expect the 'static' keyword to come first in a
declaration, and we get a warning for this with "make W=1":

drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3353:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:56:21 +03:00
Arnd Bergmann
88e97c3206 wireless: airo: rename 'register' variable
'register' is a keyword in C and cannot be used in place of a
variable name, as shown by this -Wextra warning:

drivers/net/wireless/cisco/airo.c:1105:29: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]

This replaces the 'register' keyword with a 'reg' identifier in
the declaration, which matches the definition and has the intended
meaning.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:56:20 +03:00
Amitkumar Karwar
7311ea8500 mwifiex: fix AP start problem for newly added interface
It's been observed that if interface type is changed from managed to
__ap, AP can be successfully started. But there is a problem if new
ap interface is added.

The problem got resolved after sending appropriate commands to firmware
in add_interface handler.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:54:02 +03:00
Amitkumar Karwar
568fb26ec8 mwifiex: fix AP unable to start in VHT40 problem
This patch populates secondary channel offset and downloads it to
firmware to fix the problem.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:54:01 +03:00
Amitkumar Karwar
437322ea2a mwifiex: fix system hang problem after resume
On some platforms, driver is unable to wakeup firmware after system resume
due to a problem at MMC subsystem. Triggering card reset in this case has
a race with card removal from MMC which causes system hang. This patch
resolves the problem by not triggering card reset.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:54:01 +03:00
Xinming Hu
dec277f781 mwifiex: cancel pending scan during disconnect
It is obeserved that sometimes scan operation will block the disconnect
during system suspend. It's ok to cancel ongoing scan in this case. It
reduces unnecessary system suspend delay.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:54:00 +03:00
Xinming Hu
a9c790ba23 mwifiex: factor out mwifiex_cancel_scan
This patch creates common function mwifiex_cancel_scan to remove
duplication of code.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:54:00 +03:00
Ganapathi Bhat
4699fc3f2d mwifiex: Fix an issue spotted by KASAN
When an association command is sent to firmware but the process is
killed before the command response arrives, driver will try to
access bss_desc which is already freed. This issue is fixed by
checking return value of bss_start.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:53:59 +03:00
Arnd Bergmann
08aba42fcc rtlwifi: use s8 instead of char
Compiling the rtlwifi drivers for ARM with gcc -Wextra warns about lots of
incorrect code that results from 'char' being unsigned here, e.g.

realtek/rtlwifi/rc.c:113:18: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8188ee/dm.c:1070:22: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ce/trx.c:54:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192cu/mac.c:601:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192de/trx.c:53:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ee/phy.c:1268:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192se/rf.c:150:20: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/dm.c:877:29: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/phy.c:386:16: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/dm.c:1514:38: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:1558:11: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:386:24: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/trx.c:55:12: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/stats.c:31:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]

This patch changes all uses of 'char' in this driver that refer to
8-bit integers to use 's8' instead, which is signed on all architectures.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:48:15 +03:00
Pavel Andrianov
f52b041aed libertas: Add spinlock to avoid race condition
lbs_mac_event_disconnected may free priv->currenttxskb
while lbs_hard_start_xmit accesses to it.
The patch adds a spinlock for mutual exclusion.

Tested on OLPC XO-1 (usb8388) and XO-1.5 (sd8686) with v4.7-rc3.

Confirmed that lbs_mac_event_disconnected is being called on the
station when hostapd on access point is given SIGHUP.

Signed-off-by: Pavel <andrianov@ispras.ru>
Tested-by: James Cameron <quozl@laptop.org>
Acked-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:46:56 +03:00
Bruno Herrera
6edc119ed3 wlcore: sdio: Fix crash on wlcore_probe_of when failing to parse/map irq
pdev_data pointer is being freed with kfree but the pointer is not dynamic allocated.

Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:45:19 +03:00
Andy Shevchenko
2b9c9f52dc rtl8xxxu: tuse %*ph to dump buffers
Use %*ph specifier to dump small buffers in hex format instead of doing this
byte-by-byte.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:44:32 +03:00
Jes Sorensen
08eca32ebc rtl8xxxu: Add additional documentation for RX DMA registers
This also renames REG_USB_AGG_{TO,TH} to REG_USB_AGG_{TIMEOUT,THRESH}

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:44:32 +03:00
Jes Sorensen
e4ac0a8ac8 rtl8xxxu: Add bit definitions for REG_USB_SPECIAL_OPTION
Documentation for enabling USB aggregation and whether to select
interrupt or bulk delivery of interrupt events.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:44:31 +03:00
Bhaktipriya Shridhar
452fa86e98 libertas_tf: Remove create_workqueue
alloc_workqueue replaces deprecated create_workqueue().

A dedicated workqueue has been used since the workitem (viz
&priv->cmd_work per priv, which maps to lbtf_cmd_work) is involved in
actual command processing and may be used on a memory reclaim path.
The workitems require forward progress under memory pressure and hence,
WQ_MEM_RECLAIM has been set. Since there are only a fixed number of work
items, explicit concurrency limit is unnecessary here.

Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:42:43 +03:00
Rafał Miłecki
f568adac7d brcmfmac: slightly simplify building interface combinations
This change reorders some operations in brcmf_setup_ifmodes in hope to
make it simpler:
1) It allocates arrays right before filling them. This way it's easier
   to follow requested array length as it's immediately followed by
   code filling it. It's easier to check e.g. why we need 4 entries for
   P2P. Other than that it deduplicates some checks (e.g. for P2P).
2) It reorders code to first prepare limits and then define a new combo.
   Previously this was mixed (e.g. we were setting num of channels
   before preparing limits).
3) It modifies mbss code to use i variable just like other combos do.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-06-29 18:41:34 +03:00
Grygorii Strashko
742fb20fd4 net: ethernet: ti: cpdma: switch to use genalloc
TI CPDMA currently uses a bitmap for tracking descriptors alloactions
allocations, but The genalloc already handles the same and can be used
as with special memory (SRAM) as with DMA cherent memory chank
(dma_alloc_coherent()). Hence, switch to using genalloc and add
desc_num property for each channel for limitation of max number of
allowed descriptors for each CPDMA channel. This patch do not affect
on net throuput.

Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-29 04:16:11 -04:00
Zhao Qiang
c37d4a0085 Maxim/driver: Add driver for maxim ds26522
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-29 04:05:14 -04:00
Philippe Reynes
8a79813c14 net: ethernet: dwc_eth_qos: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-28 09:12:36 -04:00