For device tree based booting, we need to use wake-up
interrupts like we already do for some omaps. This fixes
a PM regression on beagleboard compared to legacy booting.
Tested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel has never supported clk32g as a regulator since it is a clock
and not a regulator. Fortunately nothing actually references this node so
we can just remove it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.
By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.
With this change, the following now works:
interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
Fixes: 6e58b8f1da ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was used
for NAND on this board.
Commit c06c527016 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So revert back to
using software ECC scheme.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hummingboard has no over current hardware, so disable the over current
detection for both ports.
Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:
pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table
Remove it to fix this.
Fixes: commit 1d41f36a68 ("ARM: shmobile:
koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.
(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)
Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
dts files and addition of the new Rockchip list to MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJT+hwkAAoJEPOmecmc0R2Bda4IAJ7rxypWxi8RtfxULHu1oGxZ
cdmAsaedAkjTn6tye/99lv1WkLzUD+Q3AxLX6Glu8PgTkocbwtkVTP+gMbv7zwfN
Z9bA6kazPL4Rskr6Am8BFKkGhXHCXChGP1J3z9Gyh07Vu2+3zsvRzyM7hySt3TqZ
EA2dL/uODlukw6EPzFaqGWZLn1OuJmkHXDfnZ3lBI/GFZD9qt5DnYswMBlDlIwr6
D08jmcleRA3wpnY1HXYR2cN1sJmcEP6xVE8ApXd71X0MtumEy49ZTR+4T5/Sh/XN
OPheoH3UUVtXVrAa5fsoUE2xsKs3PZgnIHk1kQklpbw+HArbN+aW0Jh6CySb65Q=
=aNJj
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:
Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.
* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: Olof Johansson <olof@lixom.net>
During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.
This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only a single patch in here that fixes a DTC warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PL45
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner DT changes, take 2" from Maxime Ripard:
Only a single patch in here that fixes a DTC warning.
* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Add an "interrupt-parent = <&gic>;" at the top, which is inherited by
all child nodes, so the "interrupt-parent" properties can be removed
from the individual child nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There's already an "interrupt-parent = <&gic>;" at the top, which is
inherited by all child nodes, so the "interrupt-parent" property in
the sound node can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There's already an "interrupt-parent = <&gic>;" at the top, which is
inherited by all child nodes, so the "interrupt-parent" property in
the sound node can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There's already an "interrupt-parent = <&gic>;" at the top, which is
inherited by all child nodes, so the "interrupt-parent" properties in
the serial nodes can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic IPQ8064 SoC include device tree and support for basic booting on
the AP148 Reference board with support for UART, I2C, and SPI.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the necessary DT node to probe the serial driver on
APQ8084 platforms.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the necessary node to probe the global clock
controller on APQ8084 platforms.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.
sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ODROID kernel shows that the PMIC interrupt line is hooked up
to pin GPX3-2.
This is needed for the max77686-irq driver to create the PMIC IRQ
domain, which is needed by max77686-rtc.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch gathers a few devicetree patches needed for the reworks found in
the later patches to be sent. More precisely, it holds:
- The addition of ddrck for the sama5d3 and the sam9 SoCs
- The addition of the shutdown controller node in the sama5d3 DTSI
- The slight rework of the ramc bindings for the SoCs that have several RAM
controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4QeK
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux
Pull AT91 ramc and reset/poweroff related DT patches from Maxim Ripard:
"This branch gathers a few devicetree patches needed for the reworks found in
the later patches to be sent. More precisely, it holds:
- The addition of ddrck for the sama5d3 and the sam9 SoCs
- The addition of the shutdown controller node in the sama5d3 DTSI
- The slight rework of the ramc bindings for the SoCs that have several RAM
controllers"
Conflicts:
arch/arm/boot/dts/at91sam9g45.dtsi
The current pinfunc define all uart CTS_B IO port for DCE uart 'CTS_B'
IP port. Since uart IP port 'CTS_B' is output, and it don't need to
set 'SELECT_INPUT' bit.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Previous version had an extra 'fsl' which made the pins not match
any entry. The console message,
vf610-pinctrl 40048000.iomuxc: no fsl,pins property in node \
/soc/aips-bus@40000000/iomuxc@40048000/vf610-twr/esdhc1grp
is displayed without the fix. The prior version would generally
work as u-boot sets the pins properly for sdhc. This change allows
Linux sdhc use even if u-boot is built without sdhc support.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Fixes: 0517fe6aa8 ("ARM: dts: vf610-twr: Add support for sdhc1")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This commit adds the required pin muxing for the network interfaces and
the MDIO interface to be properly initialized. For instance, this makes
it possible for a bootloader to initialize and access the network interfaces
Only the second network interface is pin muxed. The first network interface is
connected to the PHY using SGMII, which uses a dedicated SerDes lane.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1407759281-11513-7-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the required pin muxing for the network interfaces and
the MDIO interface to be properly initialized. For instance, this makes
it possible for a bootloader to initialize and access the network interfaces
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1407759281-11513-6-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the required pin muxing for the network interfaces and
the MDIO interface to be properly initialized. For instance, this makes
it possible for a bootloader to initialize and access the network interfaces
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1407759281-11513-5-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the required pin muxing for the network interfaces and
the MDIO interface to be properly initialized. For instance, this makes
it possible for a bootloader to initialize and access the network interfaces
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1407759281-11513-4-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the required pin muxing for the network interfaces and
the MDIO interface to be properly initialized. For instance, this makes
it possible for a bootloader to initialize and access the network interfaces.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1407759281-11513-3-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the pin mux configuration for the two network interfaces
and the MDIO interface in the Armada 370 SoC .dtsi file. Only the
configuration for RGMII is added for now.
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1407759281-11513-2-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 375 SoC has the same real time clock as the one used in
other Marvell EBU platforms. This patch consequently updates the
Device Tree of the Armada 375 SoC to describe the internal RTC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1406817122-15675-1-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the Lager board specific device node part for VIN1 (composite video in);
add the device node for Analog Devices ADV7180 video decoder to IIC2 bus.
Add the necessary subnodes to interconnect VIN1 and ADV7180 devices.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[Sergei: rebased, edited changelog and summary]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the four video input controllers on the R8A7790.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[Sergei: renamed VIN device nodes, edited changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add register sets used for access by the DMA engine, and DMA properties to
the MSIOF nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DMA property to the QSPI node
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add register sets used for access by the DMA engine, and DMA properties to
the MSIOF nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DMA property to the QSPI node
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two system DMA controllers in the r8a7791 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two system DMA controllers in the r8a7790 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the SYS-DMAC0 and SYS-DMAC1 clocks to the MSTP2 clock node. They
will be used by the upcoming DMAC DT nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Koelsch board dependent part of the VIN1 device node. Add the device
node for Analog Devices ADV7180 video decoder to I2C2 bus. Add the necessary
subnodes to interconnect VIN1 and ADV7180 devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the VIN0 device node. Add the
device node for Analog Devices ADV7180 video decoder to I2C2 bus. Add the
necessary subnodes to interconnect VIN0 and ADV7180 devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 parts of the VIN[0-2] device nodes. Add aliases for
the VIN[0-2] device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC interrupt pinctrl line was added to the rk3288-evb-act8846,
but it's the same line on both the ACT8846 version and the RK808
version. This makes a lot of sense since they share the same SoC
daugherboard. Move the pinctrl definition to the common file so we
can use it for the RK808 version.
NOTE: The PMIC interrupt doesn't _actually_ go to the PMIC on the
ACT8846 version of the board (it does on the RK808), but our
convention is to label things as they're labelled on the schematics.
In the very least you can argue that this is the interrupt from the
PMIC daughtercard even if it doesn't actually go to the PMIC chip.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables basic SD and eMMC support. Things are not yet running at
the fastest speed and we don't have the regulators specified, but we
can at least use the eMMC and SD cards now.
A note:
* Though MMC DDR50 mode is partially supported in the dw_mmc
rk3288-specific code in Addy's patch, Addy's patch doesn't add
tuning support. That means DDR50 mode is not reliable. From the
3288 TRM: "Tuning is required for other speed modes-such as
DDR50-even though the output delay from the card is less than one
cycle." Thus, we don't enable MMC DDR50 mode in this patch.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the sdmmc and emmc ports on the rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
This was caused by commit 5a8da52404 ("ARM: dts: exynos5420: add dsi
node"), which conflicted with d51cad7df8 ("ARM: dts: remove display
power domain for exynos5420").
The DTS addition should never have been merged through the DRM tree in
the first place, and it lacked an ack from the platform maintainer
(who would have known that the disp_pd reference got removed).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
The EHCI and HSIC device tree nodes were added in the wrong place.
Fix them.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
development cycle:
- Get rid of the .disable() callback from the driver callback
vtable. This callback was abused and counterintuitive since
a pin or group of pins can be said to always be in some
setting, and never really disabled. We now only enable a
certain muxing, and move between some certain muxings, we
never "disable" a mux setting.
- Some janitorial moving the MSM, Samsung and Nomadik and
drivers to their own subdirectories for a clearer view in
the subsystem. This will continue.
- Kill off the use of the return value from gpiochip_remove(),
this will be done in parallel in the GPIO subsystem and
hopefully not trigger too many unchecked return value
warnings before we get rid of this altogether.
- A huge set of changes and improvements to the Allwinner
sunxi drivers especially for their latest A23 and A31 SoCs,
and some ground work for the new sun8i platform family.
- A large set of Rockchip driver improvements adding support
for the RK3288 SoC.
- Advances in migration of older Freescale platforms to pin
control, especially i.MX1.
- Samsung and Exynos improvements.
- Support for the Qualcomm MSM8960 SoC.
- Use the gpiolib irqchip helpers for the ST SPEAr and
Intel Baytrail drivers.
- A bunch of nice janitorial work done with cppcheck.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t1pR
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"This is the bulk pin control changes for the v3.17 merge development
cycle:
- get rid of the .disable() callback from the driver callback vtable.
This callback was abused and counterintuitive since a pin or group
of pins can be said to always be in some setting, and never really
disabled. We now only enable a certain muxing, and move between
some certain muxings, we never "disable" a mux setting
- some janitorial moving the MSM, Samsung and Nomadik and drivers to
their own subdirectories for a clearer view in the subsystem. This
will continue
- kill off the use of the return value from gpiochip_remove(), this
will be done in parallel in the GPIO subsystem and hopefully not
trigger too many unchecked return value warnings before we get rid
of this altogether
- a huge set of changes and improvements to the Allwinner sunxi
drivers especially for their latest A23 and A31 SoCs, and some
ground work for the new sun8i platform family
- a large set of Rockchip driver improvements adding support for the
RK3288 SoC
- advances in migration of older Freescale platforms to pin control,
especially i.MX1
- Samsung and Exynos improvements
- support for the Qualcomm MSM8960 SoC
- use the gpiolib irqchip helpers for the ST SPEAr and Intel Baytrail
drivers
- a bunch of nice janitorial work done with cppcheck"
* tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (61 commits)
pinctrl: baytrail: Convert to use gpiolib irqchip
pinctrl: sunxi: number gpio ranges starting from 0
pinctrl: sunxi: use gpiolib API to mark a GPIO used as an IRQ
pinctrl: rockchip: add drive-strength control for rk3288
pinctrl: rockchip: add separate type for rk3288
pinctrl: rockchip: set is_generic in pinconf_ops
pinctrl: msm: drop negativity check on unsigned value
pinctrl: remove all usage of gpio_remove ret val in driver/pinctl
pinctrl: qcom: Make muxing of gpio function explicit
pinctrl: nomadik: move all Nomadik drivers to subdir
pinctrl: samsung: Group all drivers in a sub-dir
sh-pfc: sh73a0: Introduce the use of devm_regulator_register
sh-pfc: Add renesas,pfc-r8a7791 to binding documentation
pinctrl: msm: move all qualcomm drivers to subdir
pinctrl: msm: Add msm8960 definitions
pinctrl: samsung: Allow pin value to be initialized using pinfunc
pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes
pinctrl: exynos: Consolidate irq_chips of GPIO and WKUP EINTs
pinctrl: samsung: Handle GPIO request and free using pinctrl helpers
pinctrl: samsung: Decouple direction setting from pinctrl
...
Merging in the few fixes we had also received, no need to keep those in
a separate branch.
* next/fixes-non-critical:
drivers: CCI: Correct use of ! and &
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
ARM: omap2+: gpmc-nand: Use dynamic platform_device_alloc()
omap16xx: Removes fixme no longer needed in ocpi_enable()
ARM: dts: OMAP5: Add device nodes for ABB
ARM: omap2+: usb-tusb6010.c: Cleaning up variable is set more than once
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
A quiet release, more bug fixes than anything else. A few things do
stand out though:
- Updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- Support for Rockchip SPI controllers (their first mainline
submission).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT4RsmAAoJELSic+t+oim9Kd0P/A3bTbf7UiK9t3NgbpIDO+yJ
JHe8O5OtxeAWGiuv9RF47Gutr8061Rww0yzX2+iiRBkaOYE7TZfdUVSBT8LnTrw6
WFye5pmxy25mDX97OJnhlsddPEoCxb/a4MlcqcCxULsHcyU9jIM+uId1v6LxMC3d
QtuB2Fuxzhhqmdfg9NLdsVsMWiwVwZn20Cmxt7Fc9EzwK6BBs1U50/X/wJHzBQ4K
fbl3hwxKODBd7aMG9DRHt4cW04WG5wQYkJS54ThUAROebqjEx8YWbNIszKA1fQcW
jBcd8Oieo724/jGZq1/U4RJUpRKmwx/ug31nrYx/Mcp+Za+yIZ1dwxAcK5AkdJNa
1lw5LGMLcP04EN0pdKKyrVwwkzV60fwrV9ELcZcnbpKhcvR0G4g7pbKufNIcGu64
0RGTnq1Y0HD1/0Zcomdt1oSSA4gv1B2Va7ZBM/SaphA+MW6EN0KfGMmcopJA5gAD
Dv66ijnIUjkKqJb4HsWa4gcq6EnqiK/GUzr9Pjng4ogl8/OF+OYOa+mYnj4DP98p
aXy/IUKSNDRwY6tV6Z4eEXnhsHWmkzfqYwZoEZVZIR7Dytl1oxdK4kW5BC0hJRc1
DrgnVMgxsIMfVD3RVbqLN4zPyFBmKHwXrcTMHQuv4ndfhiDck0u4uiF5CNCap1I1
ThAHObRbw+X/9D0ywFK/
=u37g
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release, more bug fixes than anything else. A few things do
stand out though:
- updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- support for Rockchip SPI controllers (their first mainline
submission)"
* tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device
spi: davinci: add support to configure gpio cs through dt
spi/pl022: Explicitly truncate large bitmask
spi/atmel: Fix pointer to int conversion warnings on 64 bit builds
spi: davinci: fix to support more than 2 chip selects
spi: topcliff-pch: don't hardcode PCI slot to get DMA device
spi: orion: fix incorrect handling of cell-index DT property
spi: orion: Fix error return code in orion_spi_probe()
spi/rockchip: fix error return code in rockchip_spi_probe()
spi/rockchip: remove redundant dev_err call in rockchip_spi_probe()
spi/rockchip: remove duplicated include from spi-rockchip.c
ARM: dts: fix the chip select gpios definition in the SPI nodes
spi: s3c64xx: Update binding documentation
spi: s3c64xx: use the generic SPI "cs-gpios" property
spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin"
spi: atmel: Use dmaengine_prep_slave_sg() API
spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API
spi: sh-msiof: Use correct device for DMA mapping with IOMMU
spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully
spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully
...
Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2ZIACgkQMUfUDdst+ylvQwCfQKPKcwhtq4vJ2imUzJROEZwN
ygYAnRpFpH/19X59uGSdE7DAdhbitqKg
=uPh1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2C4ACgkQMUfUDdst+yllVgCgtZl/Mcr/LlxPgjsg2C1AE7nX
YJ4An3o4N112bkdGqhZ7RjAE6K/8YILx
=rPhE
-----END PGP SIGNATURE-----
Merge tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver update from Greg KH:
"Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while"
* tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (82 commits)
tty/n_gsm.c: fix a memory leak in gsmld_open
pch_uart: don't hardcode PCI slot to get DMA device
tty: n_gsm, use setup_timer
Revert "ARC: [arcfpga] stdout-path now suffices for earlycon/console"
serial: sc16is7xx: Correct initialization of s->clk
serial: 8250_dw: Add support for deferred probing
serial: 8250_dw: Add optional reset control support
serial: st-asc: Fix overflow in baudrate calculation
serial: st-asc: Don't call BUG in asc_console_setup()
tty: serial: msm: Make of_device_id array const
tty/n_gsm.c: get gsm->num after gsm_activate_mux
serial/core: Fix too big allocation for attribute member
drivers/tty/serial: use correct type for dma_map/unmap
serial: altera_jtaguart: Fix putchar function passed to uart_console_write()
serial/uart/8250: Add tunable RX interrupt trigger I/F of FIFO buffers
Serial: allow port drivers to have a default attribute group
tty: kgdb_nmi: Automatically manage tty enable
serial: altera_jtaguart: Adpot uart_console_write()
serial: samsung: improve code clarity by defining a variable
serial: samsung: correct the case and default order in switch
...
Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no one
was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1wYACgkQMUfUDdst+ykrNwCgswPkRSAPQ3C8WvLhzUYRZZ/L
AqEAoJP0Q8Fz8unXjlSMcx7pgcqUaJ8G
=mrTQ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no
one was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while"
* tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (2199 commits)
staging: comedi: addi_apci_1564: remove diagnostic interrupt support code
staging: comedi: addi_apci_1564: add subdevice to check diagnostic status
staging: wlan-ng: coding style problem fix
staging: wlan-ng: fixing coding style problems
staging: comedi: ii_pci20kc: request and ioremap memory
staging: lustre: bitwise vs logical typo
staging: dgnc: Remove unneeded dgnc_trace.c and dgnc_trace.h
staging: dgnc: rephrase comment
staging: comedi: ni_tio: remove some dead code
staging: rtl8723au: Fix static symbol sparse warning
staging: rtl8723au: usb_dvobj_init(): Remove unused variable 'pdev_desc'
staging: rtl8723au: Do not duplicate kernel provided USB macros
staging: rtl8723au: Remove never set struct pwrctrl_priv.bHWPowerdown
staging: rtl8723au: Remove two never set variables
staging: rtl8723au: RSSI_test is never set
staging:r8190: coding style: Fixed checkpatch reported Error
staging:r8180: coding style: Fixed too long lines
staging:r8180: coding style: Fixed commenting style
staging: lustre: ptlrpc: lproc_ptlrpc.c - fix dereferenceing user space buffer
staging: lustre: ldlm: ldlm_resource.c - fix dereferenceing user space buffer
...
drivers and fixes/enhancements to existing clock drivers. There are also
some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
* improvements to printks on errors
* flattening the previously hierarchal structure of per-clock entries
in debugfs
* allow per-clock debugfs entries that are specific to a particular
clock driver
* configure initial clock parent and/or initial clock rate from Device
Tree
* several feature enhancements to the composite clock type
* misc fixes
New clock drivers added include:
* TI Palmas PMIC
* Allwinner A23 SoC
* Qualcomm APQ8084 and IPQ8064 SoCs
* Rockchip rk3188, rk3066 and rk3288 SoCs
* STMicroelectronics STiH407 SoC
* Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK down"
power saving feature for their Exynos4 & Exynos5 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=48y9
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.17 are mostly additions of new clock
drivers and fixes/enhancements to existing clock drivers. There are
also some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
- improvements to printks on errors
- flattening the previously hierarchal structure of per-clock entries
in debugfs
- allow per-clock debugfs entries that are specific to a particular
clock driver
- configure initial clock parent and/or initial clock rate from
Device Tree
- several feature enhancements to the composite clock type
- misc fixes
New clock drivers added include:
- TI Palmas PMIC
- Allwinner A23 SoC
- Qualcomm APQ8084 and IPQ8064 SoCs
- Rockchip rk3188, rk3066 and rk3288 SoCs
- STMicroelectronics STiH407 SoC
- Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK
down" power saving feature for their Exynos4 & Exynos5 SoCs"
* tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: Add missing of_clk_set_defaults export
clk: checking wrong variable in __set_clk_parents()
clk: Propagate any error return from debug_init()
clk: clps711x: Add DT bindings documentation
clk: Add CLPS711X clk driver
clk: st: Use round to closest divider flag
clk: st: Update frequency tables for fs660c32 and fs432c65
clk: st: STiH407: Support for clockgenA9
clk: st: STiH407: Support for clockgenD0/D2/D3
clk: st: STiH407: Support for clockgenC0
clk: st: Add quadfs reset handling
clk: st: Add polarity bit indication
clk: st: STiH407: Support for clockgenA0
clk: st: STiH407: Support for A9 MUX Clocks
clk: st: STiH407: Support for Flexgen Clocks
clk: st: Adds Flexgen clock binding
clk: st: Remove uncessary (void *) cast
clk: st: use static const for clkgen_pll_data tables
clk: st: use static const for stm_fs tables
clk: st: Update ST clock binding documentation
...
This patch adds common part of dsi node.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This is based on tags/exynos-power because this DT changes
are depending PMU cleanup.
Fixes boot for exynos5260 and exynos5410,
- Since exynos cannot boot without obtaining PMU address via
DT from now on, add PMU node for exynos5260 and exynos5410
For preparing exynos5250-spring,
- move max77686 and cypress,cyapa trackpad from exynos5250-
cros-common to exynos5250-snow DT file
(Note exynos5250-spring is not included in this branch yet)
For exynos3250,
- add TMU node and remove duplicated interrupt-parent
- add missing pinctrl property for uart0 and uart1
For exynos5250-smdk5250 board
- add max77686 pmic interrupt property which is connected to
gpx3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aXEe
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT 2nd updates for v3.17" from Kukjin Kim:
This is based on tags/exynos-power because this DT changes
are depending PMU cleanup.
Fixes boot for exynos5260 and exynos5410,
- Since exynos cannot boot without obtaining PMU address via
DT from now on, add PMU node for exynos5260 and exynos5410
For preparing exynos5250-spring,
- move max77686 and cypress,cyapa trackpad from exynos5250-
cros-common to exynos5250-snow DT file
(Note exynos5250-spring is not included in this branch yet)
For exynos3250,
- add TMU node and remove duplicated interrupt-parent
- add missing pinctrl property for uart0 and uart1
For exynos5250-smdk5250 board
- add max77686 pmic interrupt property which is connected to
gpx3
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (28 commits)
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
ARM: dts: Document exynos5410 PMU
ARM: EXYNOS: Move cpufreq and cpuidle device registration to init_machine
ARM: EXYNOS: Refactored code for using PMU address via DT
ARM: EXYNOS: Support cluster power off on exynos5420/5800
ARM: EXYNOS: populate suspend and powered_up callbacks for mcpm
ARM: EXYNOS: do not allow cpuidle registration for exynos5420
cpuidle: big.LITTLE: init driver for exynos5420
cpuidle: big.LITTLE: Add ARCH_EXYNOS entry in config
ARM: EXYNOS: add generic function to calculate cpu number
cpuidle: big.LITTLE: add of_device_id structure
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds socfpga Ethernet filter attributes for multicast
and unicast filters per Synopsys Ethernet IP configuration chosen
by Altera for the Cyclone 5 and Arria SOC FPGAs.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use CPU_METHOD_OF_DECLARE() instead. And declare smp method in dts file.
Changelog:
v6:
* Use hisilicon,hi3620-smp as enable-method property in Hi3620 dts.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJT2crRAAoJEPOmecmc0R2B8cAIAIke/dswgq4Kmk/G6spgdict
UXusTcy3mgnzz9X93fl+naGOopCJBSZFkTJFvNNo9nw7V+Knt1R7OW5uXMuOnwZ2
MNMEp9bmZNNKrUNqtrvZeda+Y71TCY8OKLOAnnyfnCToVQ+OCYhW4qkq/G5B3KfI
8YXK8jjhVERUG94+N6AIOxNq0qlmyoc+ZCErjUu6y3BlP/Z7OCLkEhfMmHiwMT7m
CwowMIjE0WhTt4GlVaFhHx5FvBMWI4cQWC61kCJash+U84UY1uGZ/ejPbOcIW0XP
76PCG4wt63sbpeUDjJR52e7HIzP/UGtVdVZACT82YJLpotqB3C5Mc7k/PQw46YM=
=5B5W
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rockchip-rk3288-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Basic rk3288 usb support" from Heiko Stübner:
Add support for rk3288 ehci controllers.
* tag 'v3.17-rockchip-rk3288-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the top USB port on the evb (the one closest to the Ethernet
connector).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3288 has two kind of usb controller; this adds the ehci variant for
host0 and hsic.
At the moment we don't add any phys for these controllers, but the
default settings seem to work OK.
There is a hardware problem in ohci controller which make it
unavailable and host0 controller can only support high-speed devices.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is no phy driver that works on the Rockchip board for either USB
host port yet. For now just hardcode the vbus signal to be on all the
time which makes both the dwc2 host and the EHCI port work.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Working on sound support I noticed the Apalis T30 Evaluation board
device tree missing the more generic Apalis T30 compatible string.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Indentation of the clock property used a hodgepodge of tabs and spaces.
Make them more consistent (tabs for indentation followed by spaces for
alignment).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).
After commit 78f87df2b4
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.
So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add model a5 which have additional jack detection.
Signed-off-by: Marek Belisko <marek@goldelico.com>
[tony@atomide.com: fixed a typo for make dtbs to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch is preparation of adding more boards which have common moved
to omap3-gta04.dtsi. Other boards have only small additions to omap3-gta04a4.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch add missing pinctrl for uart0/1 for Exynos3250. The gpio pin (
uart0_data, uart0_fctl, uart1_data) is only used for UART IP.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes duplicat 'interrupt-parent' property for Exynos3250
because exynos3250.dtsi already defined 'interrupt-parent' property
as following:
In arch/arm/boot/dts/exynos3250.dtsi:
compatible = "samsung,exynos3250";
interrupt-parent = <&gic>;
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add TMU (Thermal Management Unit) dt node to monitor the high
temperature for Exynos3250.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The IRQB interrupt pin of MAX77686 PMIC is connected to GPX3[2] pin of
Exynos5250 on the Exynos5250 SMDK board. Specify this connection using
interrupts property for the max77686 pmic node.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an Atmel maXTouch instead.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an s5m8767 instead.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5XAH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap n900 regression fix for v3.16 rc series" from Tony Lindgren:
Minimal regression fix for n900 display that got broken with
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
* tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert enabling of twl configuration for n900
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.
Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DMA engine is enabled for all DTs that derive from zynq-7000.dtsi.
There is no need to override the 'status' property in board DTs.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Exynos initialization code now relies on obtaining the PMU address,
so prepare a PMU node for Exynos5410.
Fixes: fce9e5bb25 ("ARM: EXYNOS: Add support for mapping PMU base
address via DT")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Update the bindings for touchscreen size.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Update the bindings for touchscreen size.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- BCM Mobile SMP support
- BRCM STB platform support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZOoN
-----END PGP SIGNATURE-----
Merge tag 'for-3.17/bcm-dt' of git://github.com/broadcom/mach-bcm into next/dt
Merge "ARM: mach-bcm: dt updatees for 3.17" from Matt Porter:
- BCM Mobile SMP support
- BRCM STB platform support
* tag 'for-3.17/bcm-dt' of git://github.com/broadcom/mach-bcm:
ARM: brcmstb: dts: add a reference DTS for Broadcom 7445
ARM: brcmstb: gic: add compatible string for Broadcom Brahma15
ARM: brcmstb: add misc. DT bindings for brcmstb
ARM: brcmstb: add CPU binding for Broadcom Brahma15
ARM: dts: enable SMP support for bcm21664
ARM: dts: enable SMP support for bcm28155
devicetree: bindings: document Broadcom CPU enable method
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc6' into next/dt
Update to Linux 3.16-rc6 as a dependency for the broadcom changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Armada XP
- New board, Lenovo ix4-300d NAS
- Add Lenovo to vendor-prefixes
- Dove
- Add LCD controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ixkt
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.17-4' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu DT changes for v3.17 (round 4)" from Jason Cooper"
- Armada XP
- New board, Lenovo ix4-300d NAS
- Add Lenovo to vendor-prefixes
- Dove
- Add LCD controllers
* tag 'mvebu-dt-3.17-4' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add dts definition for Lenovo Iomega ix4-300d NAS
of: Add Lenovo Group Ltd. to the vendor-prefixes list.
ARM: dts: dove: add DT LCD controllers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a sample DTS which will allow bootup of a board populated
with the BCM7445 chip.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Matt Porter <mporter@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Define nodes representing the two Cortex A9 CPUs in a bcm21644 SoC.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Define nodes representing the two Cortex A9 CPUs in a bcm28155 SoC.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
- convert to new clock driver
- bring structure in line with recent rk3288 comments
(no soc-nodes, using phandles when adding changes, sorted by address)
- i2c, board-pmic and pwm nodes nodes
- sd card slot and ir receiver on radxa rock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJT1jA+AAoJEPOmecmc0R2BjLUH/0tqosFsfksVGJY+MX7+foRh
KClPetsBuktT+XbOxg9LkLE8MbBvEMbtMzQDoeUk4sRyBdbX5Je+EYkF4V97KkDv
zSAAfHCXOoPPVJpuxHoVQO/sCRG38oKUhtngTPzY70Lw3Gax8R0bAPRcG8c3R++C
Tep4q8TBkRenSnHBf94rk6kiyfs0ktUAroW4oWVWICPAGpKGpQU9kUpw91QmONe1
RdqUCW3g1yKHXj3n0DYjZmouIwrc/5fybMFH0tgy/PXeGFv02kZz+3ZkBTrWr/uz
yy9hhrIKrBvRbpz0WP5b6Ij5INQBDUSx3/rU2zGnWl2DRZl7YTPAMwXAUJCPLKs=
=wLux
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rockchip-rk3xxx-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: dts: changes for existing rockchip boards" from Heiko Stuebner:
Collected changes for existing Rockchip boards
- convert to new clock driver
- bring structure in line with recent rk3288 comments
(no soc-nodes, using phandles when adding changes, sorted by address)
- i2c, board-pmic and pwm nodes nodes
- sd card slot and ir receiver on radxa rock
* tag 'v3.17-rockchip-rk3xxx-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rk3188-radxarock: add GPIO IR receiver node
ARM: dts: rockchip: add pwm nodes
ARM: dts: rockchip: add both clocks to uart nodes
ARM: dts: rk3188-radxarock: enable sd-card slot
ARM: dts: add i2c and regulator nodes to rk3188-radxarock
ARM: dts: rockchip: add tps65910 regulator for bqcurie2
ARM: dts: add rk3066 and rk3188 i2c device nodes and pinctrl settings
ARM: dts: rockchip: oder nodes by register address
ARM: dts: rockchip: remove address from pinctrl nodes
ARM: dts: uses handles to reference nodes for changes
ARM: dts: rockchip: add handles for shared nodes that don't have one yet
ARM: dts: rockchip: remove soc subnodes
arm: dts: rockchip: remove obsolete clock gate definitions
ARM: dts: rockchip: move oscillator input clock into main dtsi
ARM: dts: rockchip: add cru nodes and update device clocks to use it
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc was giving warnings for missing #address-cells and #size-cells for
the new sun6i-a31-hummingbird.dts, which has a i2c-based rtc device.
This patch adds the properties for all i2c controller nodes for sun6i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds a device tree node for the infrared receiver connected to a
GPIO pin on the Radxa Rock.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the necessary nodex and pinctrl settings for the Rockchip PWM-driver.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Modified to use the new clock defines and added rk3066 pins.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use the newly ammended dw_8250 clock binding to define both the baudclk as
well as the pclk supplying the ip.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables the 2nd i2c bus and adds the act8846 pmic as device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Curie2 uses a tps659102 as its main pmic, so add the i2c1 and tps65910
node as well as define the used voltages and regulator-names according to
the schematics.
Also fix the supply of the sd0 regulator, as it is supplied by the vio reg.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pincontroller uses the GRF and PMU syscons nowadays, so should not
contain an address in its device node.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some nodes that are changed in the dtsi hierarchy do not have handles yet.
As it was suggested in the rk3288 submission to do subsequent nodes changes
through such handle-references, add the missing ones.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Comments received from the rk3288 submission indicated that a generic subnode
to group soc components should not be used.
So to keep all rockchip devicetree files similar, remove it from rk3066 and rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The clock and reset unit is now provided by the rk3188-cru clock driver and thus
the old style definitions of the gate clocks can go away.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
The clock definitions get a lot shorter due to the soc clocks being handled by
rk3188-cru and only the input clock remains. These can now simply live
in the main rk3xxx.dtsi without affecting readability.
At the same time, rename the node to oscillator, adding a clock-output-names
property to match how the rk3288 handles this.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
This adds a node for the clock and reset unit on rk3188 and rk3066 SoCs and
also updates the device nodes retrieve their clocks from there, instead of
the previous gate clock nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
This resolves a nontrivial conflict against a bug fix
in another branch.
Conflicts:
arch/arm/mach-exynos/pm.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This allows the "make dtbs" target to work.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
There exist 2 variants using either the act8846 or rk808 as pmic, while the
rest of the board stays the same.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Node definitions shared by all rk3288 based boards.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fix the address of L2 controler register in hi3620 SoC.
This has been wrong from the point that the file was merged
in v3.14.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7b91
-----END PGP SIGNATURE-----
Merge tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung S5PV210 DT support for v3.17" from Kukjin Kim:
- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210
* tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: samsung: s5pv210: Remove legacy board support
ARM: SAMSUNG: Remove remaining legacy code
gpio: samsung: Remove legacy support of S5PV210
ARM: S5PV210: Enable multi-platform build support
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: S5PV210: Register cpufreq platform device
ARM: S5PV210: move debug-macro.S into the common space
ARM: S5PV210: Untie PM support from legacy code
ARM: S5PV210: Remove support for board files
ARM: dts: Add Device tree for s5pc110/s5pv210 boards
ARM: dts: Add Device tree for s5pv210 SoC
ARM: S5PV210: Add board file for boot using Device Tree
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: SAMSUNG: Remove legacy clock code
serial: samsung: Remove support for legacy clock code
cpufreq: s3c24xx: Remove some dead code
ARM: S5PV210: Migrate clock handling to Common Clock Framework
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge branches 'samsung/cleanup' and 'samsung/s5p-cleanup-v2', tag 'v3.16-rc6' into next/soc
The following samsung branches are based on these cleanups,
which are already in mainline before this branch gets pulled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
rc series. Mostly a fix for GPMC allocation and omap5 ABB
(Adaptive Body Bias).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT0PLHAAoJEBvUPslcq6VzVicQANRgbrIUKCHiYvi2ngRafAzT
JrJ6xDn1Z9gQSXErlc1syxrH8YFZuNth+jGBs+yvZ+kN5kh6vCXk34MANxxv/IjO
Qkm3qAjpEwGlzeW9LKwGfA9vqcnvbNJtf+xXXsaS6vB4Eac2epBjNF1aRLHqUN1n
x3buaT7otHNUYzDts5mEPkF1W8ZmmyROvcdedAYaM5wayGK/7ETO7oto4l2l9h39
rsPKX5IL+L36EDCbz45FlmiRf5jXZhR80vfcC9wR1I6om8jov4KZTPTapoSGvaxg
17UaZ2RzMvTbapUJ8kRH7fGt43GPqGO9tqxTzUEXyf1IwP6BhPmVNXNCPWlSbcGn
6zATw4DtKtqEDGu3eOLEvo5yb2QydrC3p9CIl7cmVqRECCBSEtHcoQ8pbGeMCzOP
XPaCw3TKJe5lzAqVqGcgryq7NnzhzvAzLW3MfDvSq5nsYbr8bkvv+6RqyZ7RpY7Q
sv0pROA1Niwi8XyGeFMvh+NB2MtmPXRbV4if0SeKwZAxWIvUk+RXejxyhP7WEqCe
MiUUx/tYjzDi8wjL6BqT7elpjPizR3jy1iuevmTUdsTK6Ks5QcCSwXtlKwr/VzbA
pn4u5ylclXcOuR2EOdPwjTk3++HXvDGKZtRhyjFIf6dnQB/ThJs+5yF1QrWvkiD1
alomdF9oL2wy4cf4dOLA
=nbzr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge non-urgent omap fixes from Tony Lindgren:
Fixes for omaps that were not considered urgent enough for the
rc series. Mostly a fix for GPMC allocation and omap5 ABB
(Adaptive Body Bias).
* tag 'omap-for-v3.17/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2+: gpmc-nand: Use dynamic platform_device_alloc()
omap16xx: Removes fixme no longer needed in ocpi_enable()
ARM: dts: OMAP5: Add device nodes for ABB
ARM: omap2+: usb-tusb6010.c: Cleaning up variable is set more than once
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add device tree and hwmod data for various devices
for new SoCs
- Remove legacy mailbox hwmod data that's no longer
needed for SoCs that are DT only. Note that this may
cause a minor merge conflict in mach-omap2/devices.c
with omap_init_mbox() and omap_init_hdmi_audio(), both
are legacy code that is getting removed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lKl0
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/soc-new' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "SoC related changes for omaps for v3.17 merge window"
from Tony Lindgren:
- Add device tree and hwmod data for various devices
for new SoCs
- Remove legacy mailbox hwmod data that's no longer
needed for SoCs that are DT only. Note that this may
cause a minor merge conflict in mach-omap2/devices.c
with omap_init_mbox() and omap_init_hdmi_audio(), both
are legacy code that is getting removed
* tag 'omap-for-v3.17/soc-new' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Add data for RTC
arm: dra7xx: Add hwmod data for MDIO and CPSW
arm: dra7xx: Add hwmod data for pcie1 and pcie2 subsystems
arm: dra7xx: Add hwmod data for pcie1 phy and pcie2 phy
ARM: DRA7: hwmod: Add OCP2SCP3 module
ARM: DRA7: hwmod: remove interrupts for DMA
ARM: OMAP2+: DMA: remove requirement of irq for platform-dma driver
ARM: AM33xx: hwmod_data: Remove legacy mailbox addrs
ARM: OMAP4: hwmod_data: Remove legacy mailbox addrs
ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs
ARM: OMAP2+: Avoid mailbox legacy device creation for DT-boot
ARM: DRA7: hwmod_data: Add mailbox hwmod data
ARM: dts: DRA7: Add mailbox nodes
ARM: dts: AM4372: Correct mailbox node data
ARM: dts: AM33xx: Add mailbox node
ARM: dts: OMAP4: Add mailbox node
ARM: dts: OMAP2+: Add mailbox fifo and user information
ARM: AM43xx: hwmod: add DSS hwmod data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch extends nodes of PMU system controller on Exynos4210, 4x12,
5250 and 5420 SoCs with newly defined properties used by Exynos CLKOUT
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This allows to boot the Adapteva Parallella board to serial console.
Cc: Andreas Olofsson <andreas@adapteva.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
