Test for null pointer prior to access.
Print "Not Allocated" if null pointer.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The length contained in the status word doesn't
include the status word's length itself, so we
need to account for that for tracing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The flow id (scd_flow) in a compressed BA packet should match the txq_id
of the queue from which the aggregated packets were sent. However, in
some hardware like the 1000 series, sometimes the flow id is 0 for the
txq_id (10 to 19). This can cause the annoying message:
[ 2213.306191] iwlagn 0000:01:00.0: Received BA when not expected
[ 2213.310178] iwlagn 0000:01:00.0: Read index for DMA queue txq id (0),
index 5, is out of range [0-256] 7 7.
And even worse, if agg->wait_for_ba is true when the bad BA is arriving,
this can cause system hang due to NULL pointer dereference because the
code is operating in a wrong tx queue!
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Pradeep Kulkarni <pradeepx.kulkarni@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We are seeing some race conditions between incoming station management
requests (station add/remove) and the internal unassoc RXON command that
modifies station table. Modify these flows to require the mutex to be held
and thus serializing them.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2207
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Using ieee80211_find_sta() needs to be under
RCU read lock, which iwlwifi currently misses,
so fix it.
Cc: stable@kernel.org
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the revert of "iwlwifi: move _agn statistics related structure", I
need to use CONFIG_IWLWIFI_DEBUGFS instead of CONFIG_IWLWIFI_DEBUG in
the private structure definition. Without this patch, it is possible
to get this:
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_accumulative_statistics':
drivers/net/wireless/iwlwifi/iwl-rx.c:304: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:305: error: 'struct iwl_priv' has no member named 'delta_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:306: error: 'struct iwl_priv' has no member named 'max_delta'
drivers/net/wireless/iwlwifi/iwl-rx.c:321: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:323: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:325: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:327: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:329: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:331: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_reply_statistics':
drivers/net/wireless/iwlwifi/iwl-rx.c:484: error: 'struct iwl_priv' has no member named 'accum_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:486: error: 'struct iwl_priv' has no member named 'delta_statistics'
drivers/net/wireless/iwlwifi/iwl-rx.c:488: error: 'struct iwl_priv' has no member named 'max_delta'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fairly complex code in iwlagn_tx_status_reply_tx handle the status reports for
aggregated packet batches sent by the NIC. This code aims to handle the case
where the NIC retransmits failed packets from a previous batch; the status
information for these packets can sometimes be inserted in the middle of a
batch and are actually not in order by sequence number! (I verified this can
happen with printk's in the function.)
The code in question adaptively identifies the "first" frame of the batch,
taking into account that it may not be the one corresponding to the first agg
status report, and also handles the case when the set of sent packets wraps the
256-character entry buffer. It generates the agg->bitmap field of sent packets
which is later compared to the BlockAck response from the receiver to see which
frames of those sent in this batch were ACKed. A small logic error (wrapping by
0xff==255 instead of 0x100==256) was causing the agg->bitmap to be set
incorrectly.
Fix this wrapping code, and add extensive comments to clarify what is going on.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Compressed BlockAck frames store the ACKs/NACKs in a 64-bit bitmap that starts
at the sequence number of the first frame sent in the aggregated batch. Note
that this is a selective ACKnowledgement following selective retransmission;
e.g., if frames 1,4-5 in a batch are ACKed then the next transmission will
include frames 2-3,6-10 (7 frames). In this latter case, the Compressed
BlockAck will not have all meaningful information in the low order bits -- the
semantically meaningful bits of the BA will be 0x1f3 (where the low-order frame
is seq 2).
The driver code originally just looked at the lower (in this case, 7) bits of
the BlockAck. In this case, the lower 7 bits of 0x1f3 => only 5 packets,
maximum, could ever be ACKed. In reality it should be looking at all of the
bits, filtered by those corresponding to packets that were actually sent. This
flaw meant that the number of correctly ACked packets could be significantly
underreported and might result in asynchronous state between TX and RX sides as
well as driver and uCode.
Fix this and also add a shortcut that doesn't require the code to loop through
all 64 bits of the bitmap but rather stops when no higher packets are ACKed.
In my experiments this fix greatly reduces throughput swing, making throughput
stable and high. It is also likely related to some of the stalls observed in
aggregation mode and maybe some of the buffer underruns observed, e.g.,
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1968http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2098http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2018
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The internal scanning created a problem where
when userspace tries to scan, the scan gets
rejected. Instead of doing that, queue up the
user-initiated scan when doing an internal
scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In "iwlwifi: make scan antenna forcing more generic"
I introduced generic scan RX antenna forcing, which
here I rename to make it more evident. Also add scan
TX antenna forcing, since I will need that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Channel switch host command do not need to allocate huge command buffer
since its size is already included in the iwl_device_cmd structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently, the driver allocates up to 19 skb pointers
for each TFD, of which we have 256 per queue. This
means that for each TX queue, we allocate 19k/38k
(an order 4 or 5 allocation on 32/64 bit respectively)
just for each queue's "txb" array, which contains only
the SKB pointers.
However, due to the way we use these pointers only the
first one can ever be assigned. When the driver was
initially written, the idea was that it could be
passed multiple SKBs for each TFD and attach all
those to implement gather DMA. However, due to
constraints in the userspace API and lack of TCP/IP
level checksumming in the device, this is in fact not
possible. And even if it were, the SKBs would be
chained, and we wouldn't need to keep pointers to
each anyway.
Change this to only keep track of one SKB per TFD,
and thereby reduce memory consumption to just one
pointer per TFD, which is an order 0 allocation per
transmit queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we allocate queues, we currently don't
use kzalloc() right now. When we then free
those queues again without having used all
entries, we may end up trying to free random
pointers found in the txb array since it was
never initialised. This fixes it simply by
using kzalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The iwl_hw_txq_free_tfd() function can be
called from contexts with IRQs disabled,
so it must not call dev_kfree_skb() but
rather dev_kfree_skb_any() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we free a txq that had no txb array allocated,
we still try to access it. Fix that, and also free
all SKBs that may be in the txb array (although it
can just be a single one).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This variable is now no longer used, so it
can be removed completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
use TIME_UNIT define for beacon internal calculation
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Support channel switch in driver as a separated mac80211 callback
function instead of part of mac_config callback; by moving to this
approach, uCode can have more control of channel switch timing.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the ucode beacon formation related helper function from 3945 to
iwlcore, so both _3945 and _agn devices can utilize those functions.
When driver pass the beacon related timing information to uCode in both
spectrum measurement and channel switch commands, the beacon timing
parameter require in uCode beacon format; those helper functions will do
the conversation from uSec to the correct uCode format
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
restrict_refcnt is no longer used, remove it from iwl_priv
structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Chain noise calibration data are cleared after the calibration is done
in iwlagn_gain_computation() and iwl4965_gain_computation(). This cause
the debugfs entries for those data useless. To provide valid debugging
info, clear those data right before starting the calibration instead.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This can now be much better achieved using
tracing and post-processing of the trace,
rather than doing the processing in place
in the driver, so remove a lot of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For probe request frames sent during scan, we
should use the virtual interface's mac address
that the scan was initiated on to avoid issues
when the wrong address is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we do not have an interface, priv->mac_addr
is all zeroes, so the memcpy() is not useful as
the RXON buffer has been cleared previously.
Therefore, use the interface's address that we
are setting up the RXON for, if available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
priv->mac_addr is the address of the operating
interface, not the permanent MAC address. They
are usually the same, but the user can override
the operating address, so we shouldn't set the
variable to the permanent one, it is assigned
when an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
There's no microcode that actually uses this
variable, and it is reserved for functionality
that the driver doesn't support anyway, so we
shouldn't be setting it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_connection_init_rx_config() will already
have set up the entire RXON command, so these
assignments are duplicate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Port of internal scan to iwl3945 missed introduction
of iwl3945_get_single_channel_for_scan.
Fix the following bug by introducing the iwl3945_get_single_channel_for_scan
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2208
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This can be cleanly applied to wireless-2.6 and iwlwifi git trees.
=
From: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Subject: [PATCH] iwlwifi: use the DMA state API instead of the pci equivalents
This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.
No functional change.
For further information about the background:
http://marc.info/?l=linux-netdev&m=127037540020276&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.
The debugfs code I recently added got this wrong
as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a single use of this struct member, but
as it is write-only it clearly not necessary.
Thus we can free up some space here, even if we
don't need it right now it seems pointless to
carry around the variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a2064b7a4a.
when CONFIG_IWLAGN=n:
drivers/net/wireless/iwlwifi/iwl-rx.c:254: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:303: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:304: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:305: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:306: error: 'struct iwl_priv' has no member named '_agn'
and many more.
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn-debugfs.c
drivers/net/wireless/iwlwifi/iwl-debugfs.c
drivers/net/wireless/iwlwifi/iwl-dev.h
drivers/net/wireless/iwlwifi/iwl-rx.c
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intent here is to test that "sta_id_r" is a valid pointer. We do
this same test later on in the function.
Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.
Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
there is some locking missing around the "is_internal_short_scan"
variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
scan and thus causes problems with wrong memory being accessed.
The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
switch and while statements don't need semicolons at end of statement
[ Fixup minor conflicts with recent wimax merge... -DaveM ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new PCI IDs for 6000 Series Gen2 devices
and also defines a new sku of device: 6000g2b 2x2 bgn.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cleanup the code and move all the uCode related functions specific to _agn
devices to iwl-agn-ucode.c
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The short preamble setting might change on the
fly, and then we already use the right mac80211
variable. However, in other places we don't,
which is especially wrong in the AP code since
in that case the assoc_capability is invalid.
Also, the IBSS special case is not needed since
"use_short_slot" will be properly cleared, but
the "assoc_capability" might be invalid (which
must be the reason for the special case).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
It may be desirable in some systems to have
insight into the driver via debugfs, but not
affect its operation via the debug logging
code that is inserted everywhere when DEBUG
is configured.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some comments in iwl-dev.h still refer to 4965 but used by all the _agn
devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move configuration structure for _agn devices from iwl-dev.h to
iwl-agn.h. Those data structures are for _agn devices and should be keep
for _agn devices only.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch enables all remaining 6000 series Gen2 devices.
To work-around a firmware crash problem, we disable sending
bt coex command for 6000g2b series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In order to debug problems before the ALIVE
notification is received, new firmware files
contain the event/error log information in
the file. Use that information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
There are a few places where sta_lock is used, but the
station information protected by it is accessed outside
of the lock. Address this in two ways, if the access
won't sleep then just move the access into the lock, if
the access can sleep then copy the needed station
information to the stack to be accessed without risk of
it changing while access in progress.
Additionally, a number of other places access station
station information without holding the sta_lock, fix
those as well.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This constant is not used, and incorrect, since
the broadcast ID must be used for multicast too.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The stations debugfs entry doesn't even show
the stations' MAC addresses Also, the TID
information is formatted very oddly, and
misses the important tfds_in_queue variable.
Fix this to make the file more useful.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is only used by the agn drivers,
so doesn't have to be in core and exported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Unlike agn, where the sequence numbers must
match with the TFD index, the driver for 3945
devices can use the sequence numbers provided
by mac80211 for QoS frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
If a firmware file misses one of the required
instruction or data pieces, the driver currently
crashes. Let it gracefully refuse that firmware
file instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since agn and 3945 have different statistics_notif data structure, each
should has its own statistics_flag function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
agn and 3945 has different statistics_notif data structure; since 3945
has it statistics_notif data structure inside the _3945 portion of
iwl_priv, it make sense to move the agn statistics_notif into _agn portion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
There are now five places where we need to
look up the station ID, but the sta pointer
may be NULL due to mac80211 passing that to
indicate a certain special state.
Replace all these by a new inline function,
called iwl_sta_id_or_broadcast(), and add
documentation about when to use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
During a hw restart, mac80211 will attempt to
reconfigure all stations. Currently, that fails
and leads to warnings because we still have the
stations marked active. Therefore, clear all
stations when doing down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Remove the check before invoking iwl_set_ht_add_station(),
since neither of the conditions in this check makes sense,
as either we pass in a NULL ht_info (first branch) or in
the IBSS case an ht_info with ht_enabled=false.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is now only used for the special
IBSS BSSID station, so rename it to indicate
this. The new name is iwl_add_bssid_station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
4965 code is the only thing that now still
needs iwl_find_station(), so move it there
and make it static. Everything else can
rely on the station data passed by mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With the station ID being stored in the
station struct, which mac80211 gives us
for TKIP phase 1 key updates, we can also
remove the use of iwl_find_station() in
that code path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With the station ID being stored in the
station struct, which mac80211 gives us
for aggregation callbacks, we can also
remove the use of iwl_find_station() in
those code paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since we now store the station ID in each station
struct, many places need not look at the station
table any more since they can just pull the station
ID out of the struct. Remove iwl_get_sta_id() and
use iwl_sta_id() instead as appropriate.
This reduces the amount of code needed to find the
right station significantly, and works since
mac80211 passes the station only after it has been
fully initialised, ie. even if TX races with
station addition it will only be passed to TX once
the addition is complete.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In places where the station struct is
guaranteed to exist (presumably), use
this helper to get the station ID out
of it (and warn if there's no station
struct after all).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 allows us to store private data per
station, so put the station ID there. This
allows us to avoid the station ID lookup when
removing regular stations. To also be able to
avoid the lookup to remove the special IBSS
BSSID station, track its ID in the per-vif
private data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Provide comments for newly added cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move "tx power per chain" into ucode_tx_stats, it is debugging
information provided by uCode as part of statistics notification.
The "tx power per chain" parameters are optional parameters which only
supported by 6000 series device today; those are reserved fields for all
the other devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When station is using an HT channel to communicate to AP and communication
is lost then driver will first be notified that channel is not an HT
channel anymore before AP station is removed. A consequence of that is that
the driver will know that it is not communicating on HT anymore, but the
rate scaling table is still under the impression it is operating in HT. Any
time after driver has been notified channel is not HT anymore there will
thus be a firmware SYSASSERT when the current active LQ command is sent.
A workaround for this issue is to not send a LQ command in the short time between
being notified channel is not HT anymore and rate scaling table being
updated.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2173
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently, the broadcast station is managed along
with the interface type, rather than always being
present. That leads to a bug with injection -- it
is currently not possible to inject frames when
the only virtual interface is a monitor, because
in that the required broadcast station is missing.
Additionally, allocating and deallocating the
broadcast station's LQ all the time is wasteful,
and the code to support this is fairly complex.
So this changes completely the way we manage the
broadcast station. Rather than manage it along
with any interface, we now allocate it when we
bring the device up, and remove it again when we
bring the device down. When we bring the device
up, we don't immediately program the broadcast
station into it, instead we just mark it active
and rely on the next restore cycle to upload it
to the device. This works because an unassociated
RXON is always required at least once to set up
device parameters, which implies a reprogramming
of stations into the device.
As we now manage all stations properly, there no
longer is a need for forcing a clearing of them
via iwl_clear_ucode_stations(), which can become
a lot simpler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename iwl_sta_init_lq to iwl_sta_alloc_lq and
move sending it out into the caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The "is_ap" argument to iwl_sta_init_lq is never true,
so it and the corresponding code can be removed. However,
it needs to have the station ID because it is also used
for the IBSS BSSID station, and that doesn't have the
broadcast ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The bssid member of struct iwl_priv is now
only used by 3945 code, so note that. It
shouldn't be used by any other code in the
future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Pass the virtual interface pointer to iwl_ht_conf()
so it doesn't need to rely on iw_mode and other
global variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This check is not useful, since we now no
longer dereference priv->vif at this spot.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Most of the TX aggregation handling can be passed
the virtual interface directly instead of having
to rely on priv->vif.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rather than keeping every bit of information
around in priv and the virtual interface, add
a virtual interface to many functions and use
the information directly from it.
This removes beacon_int, assoc_capability and
assoc_id from struct iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since iwl_configure_filter can now sleep since
the mac80211 callback was changed, we can now
apply filter flags changes directly.
Also, while at it, make the code a bit more
generic with a local macro. There's no need
to check changed_flags since we apply all at
the same time anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We need not check iw_mode, since we have
the vif pointer available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is only needed by 4965, so
it need not be in core code and can be
made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We never use that member of struct iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add plcp error checking for 3945. After threshold of plcp
is reached , it resets the radio
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The old firmware file type does not allow indicating
any firmware capabilities, which we frequently want
to make things easier.
This implements a new firmware type that is based on
a TLV structure, and adds a TLV for the maximum length
of probe requests in scans.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently the first four bytes in a firmware file
indicate the major, minor and api versions as well
as the serial number. These combined can never be
zero, so we can use that special case for a new,
future, file format.
This patch simply shuffles the code and prepares
for that new format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
It doesn't belong into firmware loading,
it should instead be printed after loading
the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
AGN devices all use the same ucode operations,
except for 4965, because 4965 uses only v1 file
headers.
Therefore, we can remove all the indirection
we have here and just code the API distinction
in place, with a small special case for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
As these function pointers will always point to
the 3945 functions, we can just call them directly
and avoid the indirection.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We currently display the build number only if debugging
is enabled, but it is really helpful so show it all the
time. Also store it so it can be retrieved later via
ethtool.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently iwlwifi will eventually exhaust the station
table when adding the BSSID station for IBSS mode,
unless the interface is set down.
The new mac80211 ibss joined/left notification allows
us to fix that easily by moving the code to add the
IBSS station to the notification, and also adding
code to remove it again when we leave the IBSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We'll need that function for IBSS station management,
so pass it the address, which is the only thing it
uses from the station struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl3945 should not use iwl_add_local_station(..., false)
because that would leave the IWL_STA_UCODE_INPROGRESS flag
set for the station, which is not desirable. Instead it
can use iwl3945_add_bcast_station() here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When adding the broadcast station the link quality command is
generated on demand, sent to device, and disappears. It is thus not
available for later cases when we need to restore stations and need
to send the link quality command afterwards. Now, when first adding the
broadcast station, also generate its link quality command to always be
available for later restoring.
Also fix an issue when adding local stations where the "in progress" state
is never cleared.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Dump the firmware version and build number in case of firmware SW
error. This would help firmware engineer analyze the error log.
Requested-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple error condition require fw/rf reset, driver should check all
the possible errors as long as the error checking functions for the
devices are available.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
wifi/wimax co-exist command is part of _agn device configuration
sequence; move it to iwl-agn-ucode.c which is more appropriate place for the
function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Return -EAGAIN when request tx power information and uCode is not ready;
so it will not confuse with tx power information not available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
sensitivity calibration and chain noise calibration are not available
for all the devices; use .cfg to configure the availability of those
calibration functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Instead of checking device type for enable/disable continuous ucode
trace function; put it in .cfg for better control and more
flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Instead of checking device type for enable/disable tx power control,
move it to .cfg for better control and more flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The iw_mode will always follow the only vif we
have, but using the vif directly seems easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The "chain_tx_power" debugfs function is to display the tx power per
chain based. Name it "tx_power" is misleading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For the devices do not have power save support, remove the power save
control related debugfs files.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename the current 6000 series Gen2 devices to Gen2a.
Rename the ucode name prefix to iwlwifi-6000g2a.
Also corrected the device IDs for Gen2a series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we kick off a firmware loading process,
and then unbind from the pci device right
away, we get into trouble. Avoid that by
waiting for the firmware loading to finish
(whether successfully or not) before the
unbind in iwl_pci_remove.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This mutex_unlock() has been here from the initial commit, but as nearly
as I can tell, there isn't a reason for it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.
The BUG_ON was introduced by:
commit 3110bef78c
Author: Guy Cohen <guy.cohen@intel.com>
Date: Tue Sep 9 10:54:54 2008 +0800
iwlwifi: Added support for 3 antennas
... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greenfield is a 11n feature, remove it from non-11n devices
configuration parameters list
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Separate the hw_set_hw_params() function to per device based; different
devices can have different hardware parameters set, when separate the
function based on device type can avoid mistakes, give more flexibilities and
easier to read.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The TX status code is currently abusing the ampdu_ack_map field (a bitmap) to
count the number of successfully received frames. The comments in mac80211.h
show there are actually three different, relevant variables, of which we are
currently using two, both incorrectly. Fix this by making
- ampdu_ack_len -> the number of ACKed frames (i.e. successes)
- ampdu_ack_map -> the bitmap
- ampdu_len -> the total number of frames sent (i.e., attempts)
to match the header file (and verified with ath9k's usage) and updating Intel's
RS code to match.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add general, rx and tx uCode statistics to 3945. This will help
in debugging
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When starting an aggregation session, the swq_id is generated in function
iwl_virtual_agg_queue_num() where the first parameter is supposed to be
the Access Class, but it used the tx fifo ID instead. This means the AC
value stored in swq_id is incorrect. To test this, look at the tx_queue
file in debugfs while transmitting Best Effort flow (ac=2), it shows:
hwq 10: read=0 write=0 stop=0 swq_id=0xa9 (ac 1/hwq 10)
After this fix, it will show:
hwq 10: read=0 write=0 stop=0 swq_id=0xaa (ac 2/hwq 10)
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We removed resetting of PCI_RETRY_TIMEOUT register
in merge of suspend resume work.
'Suspend and resume' resets the PCI configuration space, so we
have to disable the RETRY_TIMEOUT register again here.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
IEEE80211_CONF_SHORT_SLOT_TIME is no longer a possible setting in
ieee80211_conf->flags
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The low level transmission function is performed at uCode layer
for all the "agn" NICs, there is no statistics information available
for mac80211 get_stats() call. Remove the callback function to
avoid misleading information that returned success when indeed it is not
supported. Now return "not supported".
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Patch "iwlwifi: work around passive scan issue" was merged into
wireless-2.6, but touched a lot of code since modified (and moved)
in wireless-next-2.6. This caused some conflicts.
Conflicts:
drivers/net/wireless/iwlwifi/iwl-scan.c
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some firmware versions don't behave properly when
passive scanning is requested on radar channels
without enabling active scanning on receiving a
good frame. Work around that issue by asking the
firmware to only enable the active scanning after
receiving a huge number of good frames, a number
that can never be reached during our dwell time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some future hardware will also require some antenna
overrides so make the current logic more generic;
right now it is semantically based on a workaround
for off-channel reception but the reasons for the
new antenna overrides will be different.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Off-channel reception is acceptable in monitor
mode, and checking for monitor mode this way is
not really correct anyway since it could be the
case while operating.
Now iwl_is_monitor_mode() is no longer used so
remove it completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitor mode operation need not (and probably should
not) affect scanning this way since real monitoring
can not properly happen while scanning anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The flag name is a little misleading, this
flag instructs the device to ignore bluetooth
messages for purposes of frame transmissions,
so rename the flag to TX_CMD_FLG_IGNORE_BT.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some future hardware will require a different command to
be sent for bluetooth coexist, so make this a virtual
method that can be changed on a per-device basis.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since multiple new devices having similar uCode architecture and use same
registers address, remove more reference to 5000 series to eliminate the
confusion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Perform sanity check for turn on aggregation tid. Also remove the
option for turn on all the aggregation tids at once since it is
deprecated function and not being used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 6000g2 series of NICs, PA type is determined by uCode, driver do not
have to set the register for internal/external PA. It is a workaround
just for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add hardware revision for 6000g2 series of NIC
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is called twice in a row, remove the second one.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Use the show uCode statistics function for uCode debugging purposes only; it
is being duplicated in both debugfs and sysfs. remove the one from sysfs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch is to bring up 6000 Series 2x2 AGN Gen2 adapters.
Seperate various version numbers from 6000 Series definitions;
Add module firmware declaration for the new adapters;
Add additional device IDs and subsystem IDs;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some definition for eeprom apply to more than 5000 series device, change
the name to reflect it for easy reading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Scan requesting doesn't need to be asynchronous
since all code paths leading up to it can sleep.
Make the scan request a new util operation that
is hw-specific (to account for 3945 vs. agn)
and call it right in place.
This patch moves a lot of code into iwlagn as
it need not be in iwlcore.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
I keep checking what "priv->scan" is, so rename
it to "priv->scan_cmd" which more clearly tells
us what it is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since we no longer do a multi-pass scan,
keeping track of how long each pass took
is pointless since there will only be one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This logic is just confusing, if anything it
belongs into mac80211. Also, even if we do
scan during the EAPOL handshake, that will
not cause any problems, just a short delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With atomic bitops, test_and_{set,clear}_bit
should be used instead of separate test_bit
and set_bit/clear_bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since mac80211 will now never request scanning
multiple bands, we can remove all the associated
logic and scan a single band only in each scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Even the initial single/dual stream values will be overridden later when
issue link quality command; but still make sense not to use hard-code
value during initialization. Single/Dual stream mask are used to indicate the
best antenna for SISO/MIMO; different NIC has different tx antenna
configuration; so the parameter need to based on the valid tx antenna.
1x2 device: single tx antenna available, only SISO is valid
configuration, but still need to set up MIMO configuration, so set it up
with antenna A & B as default.
2x2 device: two tx antenna available, dual_stream will use both valid
antenna.
3x3 device: three tx antenna available, skip the first antenna and
choice the second and third antenna for dual_stream.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.
Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_wimax_coex_cmd.flags can be really uninitialized, so fix
that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mac80211 we always check both scan_req->ie and scan_req->ie_len
against zero before usage, in iwlwifi we should do the same.
Remove not needed "left -= ie_len" while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Check return code on iwl_send_cmd_pdu() to get rid of compiler warning.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-agn-rs.o
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2419: warning: unused variable ‘priv’
CC [M] drivers/net/wireless/iwlwifi/iwl-sta.o
drivers/net/wireless/iwlwifi/iwl-sta.c: In function ‘iwl_send_add_sta’:
drivers/net/wireless/iwlwifi/iwl-sta.c:197: warning: unused variable ‘sta_id’
drivers/net/wireless/iwlwifi/iwl-3945.c: In function ‘iwl3945_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-3945.c:601: warning: unused variable ‘rx_stats_noise_diff’
drivers/net/wireless/iwlwifi/iwl-3945.c:600: warning: unused variable ‘rx_stats_sig_avg’
drivers/net/wireless/iwlwifi/iwl-3945-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-3945-rs.c:650: warning: unused variable ‘priv’
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
REPLY_TX_LINK_QUALITY_CMD was used by 4965, 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Update to include additional tx command response status for "_agn"
devices.
The following status indicate the transmission was postponed:
TX_STATUS_POSTPONE_DELAY
TX_STATUS_POSTPONE_FEW_BYTES
TX_STATUS_POSTPONE_BT_PRIO
TX_STATUS_POSTPONE_QUIET_PERIOD
TX_STATUS_POSTPONE_CALC_TTAK
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When sys assert happen, driver will dump the error table information
provided by uCode. There are more information available but is not being
display by the driver; adding program counter and last host command the
to log to help uCode debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The last_phy_res[100] variable is used in an odd
way. The first byte of it is used as a flag, and
the rest as the data. Thus, the array need only
be 61 bytes, since it is just the flag and a
struct iwl_rx_phy_res (which is 60 bytes).
Clean this up by splitting the variable into two:
last_phy_res and last_phy_res_valid, using correct
types for both (struct and bool). While doing all
this also move the variables to the _agn part of
the hw-specific union since they only apply to
A-MPDUs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
lq->sta_id cannot be invalid here since this
function will only be called after the station
has been added properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Simplify the WEP group key check by checking the
sta pointer instead of the sta_id we calculate
with it; also clean up the comment formatting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Default WEP keys and regular keys are not allocated
from the same space in the firmware, so we shouldn't
use the same bits to indicate in use.
For default WEP keys, however, mac80211 won't allow
using the same key index twice, so the check is not
necessary at all -- add/remove are perfectly nested
due to those checks.
Other keys are allocated in the device in a global
array that only has a certain number of slots, so
for that we need to keep the allocation bitmap; but
the 802.11 key index isn't relevant there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The firmware clears default WEP keys on
transitions to !associated, so we need
to restore them just like stations. This
is rather implicit as part of sending a
station right now, which is odd. Make it
explicit instead and only for agn since
3945 doesn't use hw crypto for WEP.
Due to that, iwl_send_static_wepkey_cmd
is now only used in iwl-sta.c and can be
static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Size of event log is determined by uCode which is different per NICs.
Set the maximum event log size per device to better match uCode
configuration.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.
The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.
This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
Includes minor improvements in debugging messages in iwl-4965.c,
function iwl4965_is_temp_calib_needed().
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some defines used by all agn devices, but the definitions were in
iwl-4965-hw.h, move those to iwl-agn-hw.h which is the better place for
those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In iwl_rx_queue_reset(), we didn't clear the rxq->queue[]. This might
cause the same rxb appears on multiple places in rxq->queue. Although
this won't cause any problem because of the read and write pointers
protection in rxq, we'd better clear it to avoid misleading.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Module parameters used to be defined in both iwl-5000.c and iwl-4965.c,
after the code re-structure, merge into iwl-agn.c for easy to read and
maintenance.
Number of module parameters are deprecated after this merge. These are also
scheduled for removal by 2.6.40.
The current supported parameters are:
parm: debug50:50XX debug output mask (deprecated) (uint)
parm: debug:debug output mask (uint)
parm: swcrypto50:using crypto in software (default 0 [hardware])
(deprecated) (bool)
parm: swcrypto:using crypto in software (default 0 [hardware]) (int)
parm: queues_num50:number of hw queues in 50xx series (deprecated)
(int)
parm: queues_num:number of hw queues. (int)
parm: 11n_disable50:disable 50XX 11n functionality (deprecated) (int)
parm: 11n_disable:disable 11n functionality (int)
parm: amsdu_size_8K50:enable 8K amsdu size in 50XX series (deprecated)
(int)
parm: amsdu_size_8K:enable 8K amsdu size (int)
parm: fw_restart50:restart firmware in case of error (deprecated) (int)
parm: fw_restart:restart firmware in case of error (int)
parm: disable_hw_scan:disable hardware scanning (default 0) (int)
Remove "antenna" module parameter, it is not being used in "agn" driver.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().
To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Henry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We activate/deactivate QoS and setup default queue parameters in iwlwifi
driver. Mac stack do the same, so we do not need repeat that work here.
Stack also will tell when disable QoS, this will fix driver when working
with older APs, that do not have QoS implemented.
Patch make "force = true" in iwl_active_qos() assuming we always want
to do with QoS what mac stack wish.
Patch also remove unused qos_cap bits, do not initialize qos_active = 0,
as we have it initialized to zero by kzalloc.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove skb_linearize() in the iwlwifi drivers since
mac80211 supports paged rx SKBs now.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.
IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.
rates = kzalloc((sizeof(struct ieee80211_rate) * IWL_RATE_COUNT_LEGACY),
GFP_KERNEL);
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: stable@kernel.org
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously in interrupt handling tasklet, iwlwifi driver only clear/ack
those interrupts that are enabled by the driver through inta_mask.
If the hardware generates unattended interrupts, driver will not ack them,
defeating the interrupt coalescing feature. This results in high number
of interrupts per second and high CPU utilization.
This patch addresses this issue by acking those unattended interrupts
in the tasklet. Local test showed an order of magnitude improvement
in terms of the number of interrupts without sacrificing networking
throughput. This is a workaround for hardware issue.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Forget one hunk in 4965 during "iwlwifi: error checking for number of tfds
in queue" patch.
Reported-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
iwl-devtrace.h is used to declare and define trace points and
including iwl-dev.h from the file, which in turn includes other
generic headers, can lead to problems like generating duplicate copies
of generic trace points depending on the order of includes. Don't
include iwl-dev.h from iwl-devtrace.h but include it from its users -
iwl-io.h and iwl-devtrace.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Avoid checking for specified device type to perform certain function,
switch to .cfg approach as more generic and better implementation
method.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Use spin_lock_irqsave() in interrupt handler to disable interrupts locally
and provide the spinlock on SMP. This covers both interrupt and SMP
concurrency.
With this changes, also fix the sparse warning issues.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Remove the "\n" from following module parameter description:
- enable wifi/bluetooth co-exist
- led mode: 0=blinking, 1=On(RF On)/Off(RF Off), (default 0)
to be consistence with the rest of iwlagn/iwlcore module parameters format.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In stead of checking for 4965 and do KELVIN_TO_CELSIUS conversation, add
.cfg parameter for more generic approach.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We go to great lengths to calculate this value
that is never used by mac80211. Additionally,
it is now deprecated by mac80211 and is causing
driver compilation to give warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
After re-structure the agn files layout and move all the
agn shared functions out from iwl-5000.c, all those functions and data
structures do not need to be declare "extern" from iwl-5000.c in
iwl-dev.h.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move more functions only used by agn driver from iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Identify the rx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Identify the tx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
agn module parameter data structure shared by all agn devices, move it
iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Each device has it own eeprom, so the tx power version could be
different, define TX_POWER_VERSION per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices share the same common functions.
Move those functions from iwl-5000.c to iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
uCode alive for iwlagn based devices share the same functions.
Move those functions from iwl-5000.c to iwl-agn-ucode.c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hw definitions.
Move device hardware related defines from iwl-5000-hw.h to iwl-agn-hw.h
file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same tansmit queue functions.
Move tx queue related code from iwl-5000.c to iwl-agn-tx.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hcmd related functions.
Move from iwl-5000.c to iwl-agn-hcmd.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Loading uCode functions are shared across multiple agn devices.
Move those functions to iwl-agn-ucode.c file with other uCode
related functions.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same ucode loading procedure.
Move loading related code from iwl-5000.c to iwl-agn-ucode.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_good_ack_health() check for expected and actual ack count which only
apply to aggregation mode. Move the function to iwlagn module.
Reported-by: Chantry Xavier <chantry.xavier@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This reverts commit 76232ebf89.
iwl_good_ack_health only applies to aggregation and thus only to iwlagn. We
can thus move the function to iwlagn instead of modifying compile flags.
This is done in following patch.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_good_ack_health':
drivers/net/wireless/iwlwifi/iwl-rx.c:647: error: 'struct iwl_priv' has no member named '_agn'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the connectivity check and recovery routine into separated
functions based on the types
1. iwl_good_ack_health() - check for ack count
2. iwl_good_plcp_health() - check for plcp error
Based on the type of errors being detected, different recovery methods
will be used to bring the system back to normal operational state.
Because different NIC has different HW and uCode, the behavior is also
different; these functions thus now form part of the ops infrastructure,
so we can have more control on how to monitor and recover from error condition
case per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the
expected_ack_count also drops. At the same time, the aggregated
ba_timeout (the number of ba timeout retries) also rises. If the
actual_ack_count/expected_ack_count ratio is 0 and the number of ba
timeout retries rises to BA_TIMEOUT_MAX, no tx packets can be delivered.
Reloading the uCode and bring the system back to normal operational
state.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the plcp error checking into stand alone function and pointed by ops
to accommodate devices not needing this recovery.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the internal TX queues periodically. When a queue is stuck
for some unknown conditions causing the throughput to drop and the
transfer is stop, the driver will force firmware reload and bring the
system back to normal operational state.
The iwlwifi devices behave differently in this regard so this feature is
made part of the ops infrastructure so we can have more control on how to
monitor and recover from tx queue stall case per device.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Align the driver names with official product names for 1000/5000/6000
series. This change mainly affects the debug messages show up in system
log. No functional changes.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The only caller of this is iwl_rs_rate_init
which is only called with a valid sta_id.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 recently implemented two new callbacks that are used to request
station add/remove from the driver. The benefot from these new callbacks
are that they enable the driver to sleep while performing this work.
This is a big patch since a few things need to be coordinated in this move.
First we need to decouple station management from rate scaling, which
caused a lot of code to be moved and/or deleted. Next we needed to tie in
with mac80211's station management callback and let it direct our station
management as well as trigger the rate scaling initialization.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently the broadcast station is added after every RXON command. Change
this to only add the broadcast station when interface is added by mac80211.
With this we need some extra work to ensure broadcast station is always
present since station table is cleared when RXON without ASSOC bit set is
sent. To deal with this we re-add all driver known stations to uCode after
such an RXON command is sent.
We also do some cleanup and remove the various calls to clear the station
table. We now only clear the station table in two scenarios:
- only clear uCode portion of station table when RXON command without ASSOC
bit is sent
- clear uCode and driver portion when interface goes down or is removed.
We need to do this clearing when interface goes down to deal with the
device restart/reconfigure routines which do not remove the interface, but
do add the interface during reconfiguration.
Previously the keys were also cleared when station table in driver is
cleared, this is not done anymore since mac80211 will take care that keys
are set and cleared correctly.
There is a known issue with this change. Associating with different AP
without bringing interface down fails with a firmware error. This is
because of the lack of full station notification support and the later
patches in this series that complete the station notification support will
fix this.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
FH register dump debug feature was recently added for 5000 and later;
4965 can use it also.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Commit a239a8b47c introduced a
noisy message, that fills up the log very fast.
The error seems not to be fatal (the connection is stable and
performance is ok), so make it IWL_DEBUG_TX rather than IWL_ERR.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable@kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 21b2d8bd2f.
As explained by Johannes:
When we
build a probe request frame in the buffer with the SSID, we could
arrive over the limit of 200 bytes. When we build it in the buffer
without the SSID (wildcard) we don't arrive over 200 bytes, but the
ucode still allows direct probe in addition because it has an internal
buffer that is larger when it inserts the SSID...
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Recent patch "iwlwifi: move 3945 clip groups to 3945 data" exposed a memory
corruption problem. When initializing the clip groups the code was
mistakenly using the iwlagn rate count, not the 3945 rate count. This
resulted in more memory being written than was allocated.
"iwlwifi: move 3945 clip groups to 3945 data" moved the location where the
clip groups are stored and the impact is now severe in that the number of
configured TX queues is modified. Previously the
"temperature" field was overwritten, which did not seem to affect the
operation.
Fix this one instance where wrong rate count was used. I also noticed one
more location where the iwlagn rate count was used to index an iwl3945
array, fix this. I also modified one location that modified the iwlagn rate
count to obtain the iwl3945 rate count ... just use the iwl3945 rate count
directly.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2165 and
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2168
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Check successful completion of BSM loading. Give a chance to
load BSM again. If BSM loading is unsuccessful we should exit
and not initilize NIC. Before this checking even if the BSM loading failed
driver tries to initilize the NIC which should not be the case.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
4965 hardware has 7 queues reserved and the
remaining ones used for aggregation, 5000
and higher need to have 10 reserved. This
is not very clear in the code right now,
unfortunately.
Introduce a new IWL_TX_FIFO_UNUSED constant
and make the queue/FIFO mapping arrays able
to hold that value, and change the setup
code to reserve all queues in the arrays
(the queue number is the index) and use the
new unused constant to not map those queues
to any FIFO.
Additionally, clear up the AC/queue mapping
code to be more understandable. The mapping
is the identity mapping right now, but with
the mapping function I think it's easier to
understand what happens there.
Finally, HCCA isn't implemented at all and
I think newer microcode removed it, so let's
remove all mention of it in the code, some
comments remain for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add internal short scan support for 3945 NIC, This allows 3945 NIC
to support radio reset request like the other series of NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small change to remove unnecessary "ret" parameter since it not being
used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"internal_scan" debugfs function serves the same propose of mode "0" of
"force_reset" debugfs function. Remove it to avoid duplicate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_apm_stop_master and iwl_internal_short_hw_scan
are only used within iwlcore and thus do not need to be exported.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For later station notification support we would like WEP key setting to be
done synchronously always. Currently all places from which WEP key is set
can sleep, but the usage of sta_lock prevents it to do so. Modify the
locking to use priv->mutex instead and thus enable this call to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small code cleanup to remove un-necessary parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
These files are incompatible with some changes
I'm making, and don't really belong into sysfs
anyway as they can only be used for debugging.
Since writing them will probably crash the
firmware, keep only the reading part and move
them into debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since rfkill integration, mac80211 can no
longer add an interface while the hardware
is not ready, so STATUS_MODE_PENDING can
never be set.
Also, remove another superfluous channel
sanity check and return the commit_rxon
return value in case it failed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This code will never trigger, because when
we call this during interface start, neither
priv->vif nor priv->iw_mode conditions will
be true, and when it happens during reset
then priv->vif is also NULL. Also, in both
cases the same code will be executed as part
of iwl_bss_info_changed(), which contains a
copy of this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Only used on 3945, so it can be in the
3945-specific part of the data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
