The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.
Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.
It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.
Fixes: 29dd908d35 ("net: dsa: sja1105: Cancel PTP delayed work on unregister")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224 ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov says:
====================
action fixes for flow_offload infra compatibility
Fix rcu warnings due to usage of action helpers that expect rcu read lock
protection from rtnl-protected context of flow_offload infra.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao says:
====================
net: hisilicon: Fix a few problems with hip04_eth
During the use of the hip04_eth driver,
several problems were found,
which solved the hip04_tx_reclaim reentry problem,
fixed the problem that hip04_mac_start_xmit never
returns NETDEV_TX_BUSY
and the dma_map_single failed on the arm64 platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak says:
====================
Fix batched event generation for vlan action
When adding or deleting a batch of entries, the kernel sends up to
TCA_ACT_MAX_PRIO (defined to 32 in kernel) entries in an event to user
space. However it does not consider that the action sizes may vary and
require different skb sizes.
For example, consider the following script adding 32 entries with all
supported vlan parameters (in order to maximize netlink messages size):
% cat tc-batch.sh
TC="sudo /mnt/iproute2.git/tc/tc"
$TC actions flush action vlan
for i in `seq 1 $1`;
do
cmd="action vlan push protocol 802.1q id 4094 priority 7 pipe \
index $i cookie aabbccddeeff112233445566778800a1 "
args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%
patch 1 adds callback in tc_action_ops of vlan action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().
patch 2 updates the TDC test suite with relevant vlan test cases.
====================
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update TDC tests with cases varifying ability of TC to install or delete
batches of vlan actions.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add get_fill_size() routine used to calculate the action size
when building a batch of events.
Fixes: c7e2b9689 ("sched: introduce vlan action")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Fixes for -net
Couple of fixes for -net. More info in commit log.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not try to return a fragment entry from TC list. Otherwise we may not
clean properly allocated entries.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queues >= 4 we use different registers but we were not subtracting
the offset of 4. Fix this.
Found out by Coverity.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixup the XGMAC selftests by correctly finishing the implementation of
set_filter callback.
Result:
$ ethtool -t enp4s0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters -95
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdSWJ0AAoJEG4XJFUm622bwb4H/1cbH/VoPkNPfRb6783G3Fuc
SWcI655nMDHY3cElhLPGQrR4OuNYbFpBDT7O73XMIVqnkHlgq3L/VZD2qaacSd4H
tY4HEkkHobil9gdsEt8hpBstp9xNi36klDiq9gEOLT88eatdukCZTsCnBwaTFSEQ
84QxsVsHWuB+khVDay6jprA+vwL6YopOlPwfY9+q0LHWCHq1C98ZqPZoxjb8dzN7
bbW4hWIhMHRtN9ixPwvoRhscev2ZgRPHAncoGFE8bmRM79srZpG0mDeAhQPLGrJz
YSoGtylHpQxg3vzz2y80fMpH6jsUHFeA56xuKPQ5gnUm4bPeFbhx7h29DuABsAw=
=GDUP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-08-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.3
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
be_process_mcc() is invoked in 3 different places and
always with BHs disabled except the be_poll function
but since it's invoked from softirq with BHs
disabled it won't hurt.
v1->v2: added explanation to the patch
v2->v3: add a missing call from be_cmds.c
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to 'kfree_skb()' is missing in the error handling path of
'init_one()'.
This is already present in 'remove_one()' but is missing here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sun4i-emac uses the "phy" property to find the PHY it's supposed to
use. This property was deprecated in favor of "phy-handle" in commit
8c5b094476 ("dt-bindings: net: sun4i-emac: Convert the binding to a
schemas").
Add support for this new property name, and fall back to the old one in
case the device tree hasn't been updated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl1EJXQTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIHxvB/4jwFTPPBzCFxajnV2A38xantSrzz1X
p1t0JjWHUh1arN0d8P39CGwHCUKtA65uJQbrUmJO38Mon+/I8PnYksziWapC+x+A
GzucFoXwKj0SjzGnKfiM9OF5L2UZQnt2duT2DOiA4qqd0ROLPu9e3Es/++cYheHv
oRq9HQNnvHIekKiJJmZhdOwRHZB7/9W+NOecYwYZl8IDGQeguLTCFTrA/FSSmuDE
9xzZtpN5xz7ohSwp1IdKvA6gSgV42iHuRBoH4RAqIC7qCguQge1iLhqHP4DcZkik
f1C9EbQcK8J0S7n816rSEUu8vFj4tXsMA4a1EN7J0zz45eb1nL6NERbS
=JPX0
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.3-20190802' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-08-02
this is a pull request of 4 patches for net/master.
The first two patches are by Wang Xiayang, they force that the string buffer
during a dev_info() is properly NULL terminated.
The last two patches are by Tomas Bortoli and fix both a potential info leak of
kernel memory to USB devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the bridge device's vlan init bugs come from the fact that its
default pvid is created at the wrong time, way too early in ndo_init()
before the device is even assigned an ifindex. It introduces a bug when the
bridge's dev_addr is added as fdb during the initial default pvid creation
the notification has ifindex/NDA_MASTER both equal to 0 (see example below)
which really makes no sense for user-space[0] and is wrong.
Usually user-space software would ignore such entries, but they are
actually valid and will eventually have all necessary attributes.
It makes much more sense to send a notification *after* the device has
registered and has a proper ifindex allocated rather than before when
there's a chance that the registration might still fail or to receive
it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush
from br_vlan_flush() since that case can no longer happen. At
NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by
br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything
depending why it was called (if called due to NETDEV_REGISTER error
it'll still be == 1, otherwise it could be any value changed during the
device life time).
For the demonstration below a small change to iproute2 for printing all fdb
notifications is added, because it contained a workaround not to show
entries with ifindex == 0.
Command executed while monitoring: $ ip l add br0 type bridge
Before (both ifindex and master == 0):
$ bridge monitor fdb
36:7e:8a:b3:56:ba dev * vlan 1 master * permanent
After (proper br0 ifindex):
$ bridge monitor fdb
e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent
v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
v3: send the correct v2 patch with all changes (stub should return 0)
v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in
the br_vlan_bridge_event stub when bridge vlans are disabled
[0] https://bugzilla.kernel.org/show_bug.cgi?id=204389
Reported-by: michael-dev <michael-dev@fami-braun.de>
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FASTOPEN is not possible with SMC. sendmsg() with msg_flag MSG_FASTOPEN
triggers a fallback to TCP if the socket is in state SMC_INIT.
But if a nonblocking connect is already started, fallback to TCP
is no longer possible, even though the socket may still be in state
SMC_INIT.
And if a nonblocking connect is already started, a listen() call
does not make sense.
Reported-by: syzbot+bd8cc73d665590a1fcad@syzkaller.appspotmail.com
Fixes: 50717a37db ("net/smc: nonblocking connect rework")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setsockopts options TCP_NODELAY and TCP_CORK may schedule the
tx worker. Make sure the socket is not yet moved into SMC_CLOSED
state (for instance by a shutdown SHUT_RDWR call).
Reported-by: syzbot+92209502e7aab127c75f@syzkaller.appspotmail.com
Reported-by: syzbot+b972214bb803a343f4fe@syzkaller.appspotmail.com
Fixes: 01d2f7e2cd ("net/smc: sockopts TCP_NODELAY and TCP_CORK")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
desc_cnt and data_cnt should always be equal. In the case of a dropped
packet desc_cnt was still getting updated (correctly), data_cnt
was not. To eliminate this bug and prevent it from recurring this
patch combines them into one ring level cnt.
Signed-off-by: Catherine Sullivan <csully@google.com>
Reviewed-by: Sagi Shahar <sagis@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop path in rt6_update_exception_stamp_rt needs to call
rcu_read_unlock if it fails to find a fib6_nh match rather than
just returning.
Fixes: e659ba31d8 ("ipv6: Handle all fib6_nh in a nexthop in exception handling")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that shutdown never works, and at the same time document how
I tested to came to the conclusion that currently reuse is not possible.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like we were slightly overzealous with the shutdown()
cleanup. Even though the sock->sk_state can reach CLOSED again,
socket->state will not got back to SS_UNCONNECTED once
connections is ESTABLISHED. Meaning we will see EISCONN if
we try to reconnect, and EINVAL if we try to listen.
Only listen sockets can be shutdown() and reused, but since
ESTABLISHED sockets can never be re-connected() or used for
listen() we don't need to try to clean up the ULP state early.
Fixes: 32857cf57f ("net/tls: fix transition through disconnect with close")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer says:
====================
net: fix regressions for generic-XDP
Thanks to Brandon Cazander, who wrote a very detailed bug report that
even used perf probe's on xdp-newbies mailing list, we discovered that
generic-XDP contains some regressions when using bpf_xdp_adjust_head().
First issue were that my selftests script, that use bpf_xdp_adjust_head(),
by mistake didn't use generic-XDP any-longer. That selftest should have
caught the real regression introduced in commit 458bf2f224 ("net: core:
support XDP generic on stacked devices.").
To verify this patchset fix the regressions, you can invoked manually via:
cd tools/testing/selftests/bpf/
sudo ./test_xdp_vlan_mode_generic.sh
sudo ./test_xdp_vlan_mode_native.sh
====================
Link: https://www.spinics.net/lists/xdp-newbies/msg01231.html
Fixes: 458bf2f224 ("net: core: support XDP generic on stacked devices.")
Reported by: Brandon Cazander <brandon.cazander@multapplied.net>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generic-XDP was moved to a later processing step by commit
458bf2f224 ("net: core: support XDP generic on stacked devices.")
a regression was introduced when using bpf_xdp_adjust_head.
The issue is that after this commit the skb->network_header is now
changed prior to calling generic XDP and not after. Thus, if the header
is changed by XDP (via bpf_xdp_adjust_head), then skb->network_header
also need to be updated again. Fix by calling skb_reset_network_header().
Fixes: 458bf2f224 ("net: core: support XDP generic on stacked devices.")
Reported-by: Brandon Cazander <brandon.cazander@multapplied.net>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given the increasing number of BPF selftests, it makes sense to
reduce the time to execute these tests. The ping parameters are
adjusted to reduce the time from measures 9 sec to approx 2.8 sec.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In-order to test both native-XDP (xdpdrv) and generic-XDP (xdpgeneric)
create two wrapper test scripts, that start the test_xdp_vlan.sh script
with these modes.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change BPF selftest test_xdp_vlan.sh to (default) use generic XDP.
This selftest was created together with a fix for generic XDP, in commit
2972495699 ("net: fix generic XDP to handle if eth header was
mangled"). And was suppose to catch if generic XDP was broken again.
The tests are using veth and assumed that veth driver didn't support
native driver XDP, thus it used the (ip link set) 'xdp' attach that fell
back to generic-XDP. But veth gained native-XDP support in 948d4f214f
("veth: Add driver XDP"), which caused this test script to use
native-XDP.
Fixes: 948d4f214f ("veth: Add driver XDP")
Fixes: 97396ff0bc ("selftests/bpf: add XDP selftests for modifying and popping VLAN headers")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 069d11465a ("net/mlx5e: RX, Enhance legacy Receive Queue
memory scheme") introduced an undefined behaviour below due to
"frag->last_in_page" is only initialized in mlx5e_init_frags_partition()
when,
if (next_frag.offset + frag_info[f].frag_stride > PAGE_SIZE)
or after bailed out the loop,
for (i = 0; i < mlx5_wq_cyc_get_size(&rq->wqe.wq); i++)
As the result, there could be some "frag" have uninitialized
value of "last_in_page".
Later, get_frag() obtains those "frag" and check "frag->last_in_page" in
mlx5e_put_rx_frag() and triggers the error during boot. Fix it by always
initializing "frag->last_in_page" to "false" in
mlx5e_init_frags_partition().
UBSAN: Undefined behaviour in
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:325:12
load of value 170 is not a valid value for type 'bool' (aka '_Bool')
Call trace:
dump_backtrace+0x0/0x264
show_stack+0x20/0x2c
dump_stack+0xb0/0x104
__ubsan_handle_load_invalid_value+0x104/0x128
mlx5e_handle_rx_cqe+0x8e8/0x12cc [mlx5_core]
mlx5e_poll_rx_cq+0xca8/0x1a94 [mlx5_core]
mlx5e_napi_poll+0x17c/0xa30 [mlx5_core]
net_rx_action+0x248/0x940
__do_softirq+0x350/0x7b8
irq_exit+0x200/0x26c
__handle_domain_irq+0xc8/0x128
gic_handle_irq+0x138/0x228
el1_irq+0xb8/0x140
arch_cpu_idle+0x1a4/0x348
do_idle+0x114/0x1b0
cpu_startup_entry+0x24/0x28
rest_init+0x1ac/0x1dc
arch_call_rest_init+0x10/0x18
start_kernel+0x4d4/0x57c
Fixes: 069d11465a ("net/mlx5e: RX, Enhance legacy Receive Queue memory scheme")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently init call of all actions (except ipt) init their 'parm'
structure as a direct pointer to nla data in skb. This leads to race
condition when some of the filter actions were initialized successfully
(and were assigned with idr action index that was written directly
into nla data), but then were deleted and retried (due to following
action module missing or classifier-initiated retry), in which case
action init code tries to insert action to idr with index that was
assigned on previous iteration. During retry the index can be reused
by another action that was inserted concurrently, which causes
unintended action sharing between filters.
To fix described race condition, save action idr index to temporary
stack-allocated variable instead on nla data.
Fixes: 0190c1d452 ("net: sched: atomically check-allocate action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to drop the adjust_link callback in order to finally migrate to
phylink.
Otherwise we get the following warning during startup:
"mv88e6xxx 2188000.ethernet-1:10: Using legacy PHYLIB callbacks. Please
migrate to PHYLINK!"
The warning is generated in the function dsa_port_link_register_of in
dsa/port.c:
int dsa_port_link_register_of(struct dsa_port *dp)
{
struct dsa_switch *ds = dp->ds;
if (!ds->ops->adjust_link)
return dsa_port_phylink_register(dp);
dev_warn(ds->dev,
"Using legacy PHYLIB callbacks. Please migrate to PHYLINK!\n");
[...]
}
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two reset-gpio sanity checks which were never converted to use
gpio_is_valid(), and make sure to use -EINVAL to indicate a missing
reset line also for the UART-driver module parameter and for the USB
driver.
This specifically prevents the UART and USB drivers from incidentally
trying to request and use gpio 0, and also avoids triggering a WARN() in
gpio_to_desc() during probe when no valid reset line has been specified.
Fixes: e33a3f84f8 ("NFC: nfcmrvl: allow gpio 0 for reset signalling")
Reported-by: syzbot+cf35b76f35e068a1107f@syzkaller.appspotmail.com
Tested-by: syzbot+cf35b76f35e068a1107f@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
There are a lot of those warnings with GCC8+ 64-bit,
In file included from ./include/linux/sctp.h:42,
from net/core/skbuff.c:47:
./include/uapi/linux/sctp.h:395:1: warning: alignment 4 of 'struct
sctp_paddr_change' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:728:1: warning: alignment 4 of 'struct
sctp_setpeerprim' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:727:26: warning: 'sspp_addr' offset 4 in
'struct sctp_setpeerprim' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage sspp_addr;
^~~~~~~~~
./include/uapi/linux/sctp.h:741:1: warning: alignment 4 of 'struct
sctp_prim' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:740:26: warning: 'ssp_addr' offset 4 in
'struct sctp_prim' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage ssp_addr;
^~~~~~~~
./include/uapi/linux/sctp.h:792:1: warning: alignment 4 of 'struct
sctp_paddrparams' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:784:26: warning: 'spp_address' offset 4 in
'struct sctp_paddrparams' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage spp_address;
^~~~~~~~~~~
./include/uapi/linux/sctp.h:905:1: warning: alignment 4 of 'struct
sctp_paddrinfo' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:899:26: warning: 'spinfo_address' offset 4
in 'struct sctp_paddrinfo' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage spinfo_address;
^~~~~~~~~~~~~~
This is because the commit 20c9c825b1 ("[SCTP] Fix SCTP socket options
to work with 32-bit apps on 64-bit kernels.") added "packed, aligned(4)"
GCC attributes to some structures but one of the members, i.e, "struct
sockaddr_storage" in those structures has the attribute,
"aligned(__alignof__ (struct sockaddr *)" which is 8-byte on 64-bit
systems, so the commit overwrites the designed alignments for
"sockaddr_storage".
To fix this, "struct sockaddr_storage" needs to be aligned to 4-byte as
it is only used in those packed sctp structure which is part of UAPI,
and "struct __kernel_sockaddr_storage" is used in some other
places of UAPI that need not to change alignments in order to not
breaking userspace.
Use an implicit alignment for "struct __kernel_sockaddr_storage" so it
can keep the same alignments as a member in both packed and un-packed
structures without breaking UAPI.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is likely that PAL_BDC_CR should be PLA_BDC_CR.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like FSL_ENETC, when CONFIG_FSL_ENETC_VF is set,
we should select PHYLIB, otherwise building still fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c:(.text+0x2744): undefined reference to `phy_start'
enetc.c:(.text+0x282c): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c:(.text+0x28f8): undefined reference to `phy_stop'
enetc.c:(.text+0x2904): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x3f8): undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x400): undefined reference to `phy_ethtool_set_link_ksettings'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
strncpy() does not ensure NULL-termination when the input string
size equals to the destination buffer size 30.
The output string is passed to qed_int_deassertion_aeu_bit()
which calls DP_INFO() and relies NULL-termination.
Use strlcpy instead. The other conditional branch above strncpy()
needs no fix as snprintf() ensures NULL-termination.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
board is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/iphase.c:2765 ia_ioctl() warn: potential spectre issue 'ia_dev' [r] (local cap)
drivers/atm/iphase.c:2774 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2782 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2816 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2823 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2830 ia_ioctl() warn: potential spectre issue '_ia_dev' [r] (local cap)
drivers/atm/iphase.c:2845 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2856 ia_ioctl() warn: possible spectre second half. 'iadev'
Fix this by sanitizing board before using it to index ia_dev and _ia_dev
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition for an established connection that is being closed
by the guest: the refcnt is 4 at the end of hvs_release() (Note: here the
'remove_sock' is false):
1 for the initial value;
1 for the sk being in the bound list;
1 for the sk being in the connected list;
1 for the delayed close_work.
After hvs_release() finishes, __vsock_release() -> sock_put(sk) *may*
decrease the refcnt to 3.
Concurrently, hvs_close_connection() runs in another thread:
calls vsock_remove_sock() to decrease the refcnt by 2;
call sock_put() to decrease the refcnt to 0, and free the sk;
next, the "release_sock(sk)" may hang due to use-after-free.
In the above, after hvs_release() finishes, if hvs_close_connection() runs
faster than "__vsock_release() -> sock_put(sk)", then there is not any issue,
because at the beginning of hvs_close_connection(), the refcnt is still 4.
The issue can be resolved if an extra reference is taken when the
connection is established.
Fixes: a9eeb998c2 ("hv_sock: Add support for delayed close")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com
Fixes: f14e22435a ("net: can: peak_usb: Do not do dma on the stack")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string is
passed to dev_info() which relies on the NULL-termination.
Use strlcpy() instead.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
