The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
Since there is no public documentation, this driver is mostly the
one published by MOXA that has been heavily cleaned up / ported
from linux 2.6.9.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding paged frags skbs to af_unix sockets introduced a performance
regression on large sends because of additional page allocations, even
if each skb could carry at least 100% more payload than before.
We can instruct sock_alloc_send_pskb() to attempt high order
allocations.
Most of the time, it does a single page allocation instead of 8.
I added an additional parameter to sock_alloc_send_pskb() to
let other users to opt-in for this new feature on followup patches.
Tested:
Before patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 46861.15
After patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 57981.11
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_stream_sendmsg() currently uses order-2 allocations,
and we had numerous reports this can fail.
The __GFP_REPEAT flag present in sock_alloc_send_pskb() is
not helping.
This patch extends the work done in commit eb6a24816b
("af_unix: reduce high order page allocations) for
datagram sockets.
This opens the possibility of zero copy IO (splice() and
friends)
The trick is to not use skb_pull() anymore in recvmsg() path,
and instead add a @consumed field in UNIXCB() to track amount
of already read payload in the skb.
There is a performance regression for large sends
because of extra page allocations that will be addressed
in a follow-up patch, allowing sock_alloc_send_pskb()
to attempt high order page allocations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Encrypt the cookie with both server and client IPv4 addresses,
such that multi-homed server will grant different cookies
based on both the source and destination IPs. No client change
is needed since cookie is opaque to the client.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
callid_sock array is referenced via rcu_dereference and
sparse rcu checks complains about address space mismatch.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the new procfs knobs:
/proc/sys/net/ipv4/conf/*/igmpv2_unsolicited_report_interval
/proc/sys/net/ipv4/conf/*/igmpv3_unsolicited_report_interval
Which will allow userspace configuration of the IGMP unsolicited report
interval (see below) in milliseconds. The defaults are 10000ms for IGMPv2
and 1000ms for IGMPv3 in accordance with RFC2236 and RFC3376.
Background:
If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent. The
delay between joins is the "IGMP Unsolicited Report Interval".
Prior to this patch this value was hard coded in the kernel to 10s for
IGMPv2 and 1s for IGMPv3. 10s is unsuitable for some use-cases, such as
IPTV as it can cause channel change to be slow in the presence of packet
loss.
This patch allows the value to be overridden from userspace for both
IGMPv2 and IGMPv3 such that it can be tuned accoding to the network.
Tested with Wireshark and a simple program to join a (non-existent)
multicast group. The distribution of timings for the second join differ
based upon setting the procfs knobs.
igmpvX_unsolicited_report_interval is intended to follow the pattern
established by force_igmp_version, and while a procfs entry has been added
a corresponding sysctl knob has not as it is my understanding that sysctl
is deprecated[1].
[1]: http://lwn.net/Articles/247243/
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The procfs knob /proc/sys/net/ipv4/conf/*/force_igmp_version allows the
IGMP protocol version to use to be explicitly set. As a side effect this
caused the routing cache to be flushed as it was declared as a
DEVINET_SYSCTL_FLUSHING_ENTRY. Flushing is unnecessary and this patch
makes it so flushing does not occur.
Requested by Hannes Frederic Sowa as he was reviewing other patches
adding procfs entries.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent. The
delay between joins is the "IGMP Unsolicited Report Interval".
Previously this value was hard coded to be chosen randomly between 0-10s.
This can be too long for some use-cases, such as IPTV as it can cause
channel change to be slow in the presence of packet loss.
The value 10s has come from IGMPv2 RFC2236, which was reduced to 1s in
IGMPv3 RFC3376. This patch makes the kernel use the 1s value from the
later RFC if we are operating in IGMPv3 mode. IGMPv2 behaviour is
unaffected.
Tested with Wireshark and a simple program to join a (non-existent)
multicast group. The distribution of timings for the second join differ
based upon setting /proc/sys/net/ipv4/conf/eth0/force_igmp_version.
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of bond_add_vlan() failure currently we'll have the vlan's
refcnt bumped up in all slaves, but it will never go down because it
failed to get added to the bond, so properly unwind the added vlan if
bond_add_vlan fails.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have vlan_vids_add/del_by_dev() which serve the same purpose as
bond's bond_add/del_vlans_on_slave() with the good side effect of
reverting the changes if one of the additions fails.
There's only 1 change in the behaviour of enslave: if adding of the
vlans to the slave fails, we'll fail the enslaving because otherwise we
might delete some vlan that wasn't added by the bonding.
The only way this may happen is with ENOMEM currently, so we're in trouble
anyway.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With GRO/LRO processing, there is a problem because Ip[6]InReceives SNMP
counters do not count the number of frames, but number of aggregated
segments.
Its probably too late to change this now.
This patch adds four new counters, tracking number of frames, regardless
of LRO/GRO, and on a per ECN status basis, for IPv4 and IPv6.
Ip[6]NoECTPkts : Number of packets received with NOECT
Ip[6]ECT1Pkts : Number of packets received with ECT(1)
Ip[6]ECT0Pkts : Number of packets received with ECT(0)
Ip[6]CEPkts : Number of packets received with Congestion Experienced
lph37:~# nstat | egrep "Pkts|InReceive"
IpInReceives 1634137 0.0
Ip6InReceives 3714107 0.0
Ip6InNoECTPkts 19205 0.0
Ip6InECT0Pkts 52651828 0.0
IpExtInNoECTPkts 33630 0.0
IpExtInECT0Pkts 15581379 0.0
IpExtInCEPkts 6 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commits:
0f75b09c79cbd89acb9ec483e02614
Amongst other things, it's modifies the SKB header
to pull the ethernet headers off via eth_type_trans()
on the output path which is bogus.
It's causing serious regressions for people.
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8873mll_read_status() is used only in this file.
Fix the following sparse warning:
drivers/net/phy/micrel.c:147:5: warning: symbol 'ksz8873mll_read_status' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_copy_datagram_from_iovec() to avoid code duplication and make it easy to
be read. Also we can do the skipping inside the zero-copy loop.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To let it be reused and reduce code duplication. Also document this function.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP tunnel hash heads can be embedded in the per-net structure
since it is a fixed size. Reduce the size so that the total structure
fits in a page size. The original size was overly large, even NETDEV_HASHBITS
is only 8 bits!
Also, add some white space for readability.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL and power state changes will now be done in the shutdown handler.
open/close/ethtool will no longer change the power state. NVRAM
operations can now be permitted whether the device is up or down.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate MAC and PHY WoL setup code into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by closing the device if necessary. Otherwise, since NAPI state is
already disabled, a subsequent close will hang the system.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uninitialized value was being returned in the non-failure case.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log the event type for unknown async events
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BE2 FW GET_PHY_DETAILS cmd does not return fixed speeds supported.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SH-R and Lancer-R, use the FW supported values for Max unicast MACs,
Max VLANs and Max multicast MACs.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a chip wide value and the PFs already report it.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new speeds are supported by variants of the Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup gfar_start_xmit()'s fast path by factoring out "redundant"
FCB insertion code (repeated gfar_add_fcb() calls and related)
and by reducing the number of if() clauses (i.e. if(fcb) checks).
Improve maintainability (e.g. there's less code and easier to read)
also by introducing do_csum and do_vlan to mark the other 2 Tx TOE
functionalities, following the same model as do_tstamp.
fcb_len may also be 0 now, to mark that Tx FCB insertion conditions
(do_csum, do_vlan, do_tstamp) have not been met.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.
The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're already protected by RTNL lock, so nothing can happen to bond/its
slaves, and thus the locking is useless here (both bond->lock and
bond->curr_active_slave).
Also, add ASSERT_RTNL() both to bond_set_rx_mode() and bond_hw_addr_swap()
to catch possible uses of it without RTNL locking.
This patch also saves us from a lockdep false-positive in
bond_set_rx_mode() vs bond_hw_addr_swap().
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version has a minor changes and the offsets are same as the
previous version, so adding new IP version support in the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use a lot of time comparison math for arp_interval
comparisons, which are sometimes quite hard to read and understand.
All the time comparisons have one pattern:
(time - arp_interval_jiffies) <= jiffies <= (time + mod *
arp_interval_jiffies + arp_interval_jiffies/2)
Introduce a new helper - bond_time_in_interval(), which will do the math in
one place and, thus, will clean up the logical code. This helper introduces
a bit of overhead (by always calculating the jiffies from arp_interval),
however it's really not visible, considering that functions using it
usually run once in arp_interval milliseconds.
There are several lines slightly over 80 chars, however breaking them would
result in more hard-to-read code than several character after the 80 mark.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
