This adds a new quirk NVME_QUIRK_NO_TEMP_THRESH_CHANGE to avoid changing
the value of the temperature threshold feature for specific devices that
show undesirable behavior.
Guenter reported:
"On my Intel NVME drive (SSDPEKKW512G7), writing any minimum limit on the
Composite temperature sensor results in a temperature warning, and that
warning is sticky until I reset the controller.
It doesn't seem to matter which temperature I write; writing -273000 has
the same result."
The Intel NVMe has the latest firmware version installed, so this isn't
a problem that was ever fixed.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jean Delvare <jdelvare@suse.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
According to the NVMe specification, the over temperature threshold and
under temperature threshold features shall be implemented for Composite
Temperature if a non-zero WCTEMP field value is reported in the Identify
Controller data structure. The features are also implemented for all
implemented temperature sensors (i.e., all Temperature Sensor fields that
report a non-zero value).
This provides the over temperature threshold and under temperature
threshold for each sensor as temperature min and max values of hwmon
sysfs attributes.
The WCTEMP is already provided as a temperature max value for Composite
Temperature, but this change isn't incompatible. Because the default
value of the over temperature threshold for Composite Temperature is
the WCTEMP.
Now the alarm attribute for Composite Temperature indicates one of the
temperature is outside of a temperature threshold. Because there is only
a single bit in Critical Warning field that indicates a temperature is
outside of a threshold.
Example output from the "sensors" command:
nvme-pci-0100
Adapter: PCI adapter
Composite: +33.9°C (low = -273.1°C, high = +69.8°C)
(crit = +79.8°C)
Sensor 1: +34.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 2: +31.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 5: +47.9°C (low = -273.1°C, high = +65261.8°C)
This also adds helper macros for kelvin from/to milli Celsius conversion,
and replaces the repeated code in hwmon.c.
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jean Delvare <jdelvare@suse.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Sagi and I have been pretty busy lately, and Chaitanya has been
helping a lot with target work and agreed to share the load.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Users observe IOMMU related errors when performing discard on nvme from
non-compliant nvme devices reading beyond the end of the DMA mapped
ranges to discard.
Two different variants of this behavior have been observed: SM22XX
controllers round up the read size to a multiple of 512 bytes, and Phison
E12 unconditionally reads the maximum discard size allowed by the spec
(256 segments or 4kB).
Make nvme_setup_discard unconditionally allocate the maximum DSM buffer
so the driver DMA maps a memory range that will always succeed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202665 many
Signed-off-by: Eduard Hasenleithner <eduard@hasenleithner.at>
[changelog, use existing define, kernel coding style]
Signed-off-by: Keith Busch <kbusch@kernel.org>
nvme devices report temperature information in the controller information
(for limits) and in the smart log. Currently, the only means to retrieve
this information is the nvme command line interface, which requires
super-user privileges.
At the same time, it would be desirable to be able to use NVMe temperature
information for thermal control.
This patch adds support to read NVMe temperatures from the kernel using the
hwmon API and adds temperature zones for NVMe drives. The thermal subsystem
can use this information to set thermal policies, and userspace can access
it using libsensors and/or the "sensors" command.
Example output from the "sensors" command:
nvme0-pci-0100
Adapter: PCI adapter
Composite: +39.0°C (high = +85.0°C, crit = +85.0°C)
Sensor 1: +39.0°C
Sensor 2: +41.0°C
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Check validity of offset into ANA log buffer before accessing
nvme_ana_group_desc. This check ensures the size of ANA log buffer >=
offset + sizeof(nvme_ana_group_desc)
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Prabhath Sajeepa <psajeepa@purestorage.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_set_op_attrs has been long deprecated, replace it with a direct
assignment of the flags to bio->bi_opf.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With reference to the following issue reported on the mailing list :-
http://lists.infradead.org/pipermail/linux-nvme/2019-October/027604.html
this patch adds plugging for the bdev-ns under nvmet_bdev_execute_rw().
We can see the following performance improvement in random write
workload I/Os with the setup described in the link when device_path
configured as /dev/md0.
Without this patch :-
write: IOPS=40.8k, BW=159MiB/s (167MB/s)(4777MiB/30002msec)
write: IOPS=41.2k, BW=161MiB/s (169MB/s)(4831MiB/30011msec)
slat (usec): min=8, max=10823, avg=15.64, stdev=16.85
slat (usec): min=8, max=401, avg=15.40, stdev= 9.56
clat (usec): min=54, max=2492, avg=759.07, stdev=172.62
clat (usec): min=56, max=1997, avg=768.06, stdev=178.72
With this patch :-
write: IOPS=123k, BW=480MiB/s (504MB/s)(14.1GiB/30011msec)
write: IOPS=123k, BW=481MiB/s (504MB/s)(14.1GiB/30002msec)
slat (usec): min=8, max=9941, avg=13.31, stdev= 8.04
slat (usec): min=8, max=289, avg=13.31, stdev= 3.37
clat (usec): min=43, max=17635, avg=245.46, stdev=171.23
clat (usec): min=44, max=17751, avg=245.25, stdev=183.14
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the special cases for fabrics commands and the discovery controller
to nvmet_parse_admin_cmd in preparation for adding passthrough support.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Discovery controllers need this information as well.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that nvmet_req_execute does nothing, open code it.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[split patch, update changelog]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of storing the expected length and checking it when it's
executed, just check the length inside the command themselves.
A new helper, nvmet_check_data_len() is created to help with this
check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[split patch, udpate changelog]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Push the lid and cns check into their respective handlers and, while
we're at it, rename the functions to be consistent with other
discovery handlers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[split patch, update changelog]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of picking the sub-command handler to execute in a nested
switch statement introduce a landing functions that calls out
to the appropriate sub-command handler.
This will allow us to have a common place in the handler to check
the transfer length in a future patch.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[split patch, update change log]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It's not apprporiate for the transports to set the data_len
field of the request which is only used by the core.
In this case, just use a variable on the stack to store the
length of the sgl for comparison.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
None of the other transports check data_len which is verified
in core code. The function should instead check that the sgl length
is non-zero.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce the new helper function nvme_lba_to_sect() to convert a device
logical block number to a 512B sector number. Use this new helper in
obvious places, cleaning up the code.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename nvme_block_nr() to nvme_sect_to_lba() and use SECTOR_SHIFT
instead of its hard coded value 9. Also add a comment to decribe this
helper.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update enumerations and structures in include/linux/nvme.h
to resync with the nvmecli.
All the updates are mentioned in the ratified NVMe 1.4 spec
https://nvmexpress.org/wp-content/uploads/NVM-Express-1_4-2019.06.10-Ratified.pdf
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvme_cleanup_cmd should be called for each call to nvme_setup_cmd
(symmetrical functions). Move the call for nvme_cleanup_cmd to the common
core layer and call it during nvme_complete_rq for the good flow. For
error flow, each transport will call nvme_cleanup_cmd independently. Also
take care of a special case of path failure, where we call
nvme_complete_rq without doing nvme_setup_cmd.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix the status code of canceled requests initiated by the host according
to TP4028 (Status Code 0x371):
"Command Aborted By host: The command was aborted as a result of host
action (e.g., the host disconnected the Fabric connection)."
Also in a multipath environment, unless otherwise specified, errors of
this type (path related) should be retried using a different path, if
one is available.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The calls to nvmet_req_alloc_sgl and rdma_rw_ctx_init should usually
succeed, so add this simple optimization to the fast path.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The call to sgl_alloc shouldn't fail so add this simple optimization to
the fast path.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This commit doesn't change any logic.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function improves code readability and reduces code duplication.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Code today only clears the association_id if a Disconnect LS is transmit.
Remove ambiguity and unconditionally clear the association_id if the
association has been terminated.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Change wording on a couple of messages to clarify what happened.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set the new category field in the FC-NVME CMND_IU based on queue number.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sync sources with revised structure and field names to correspond with
FC-NVME-2 header sync-up.
Tested interoperability with success:
- prior initiator with new target
- prior target with new initiator
- new on new
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sync the header to FC-NVME-2 r1.06 (T11-2019-00210-v001).
Includes some minor mods where pre-release field names changed
by the time the spec was released.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, if the loop device receives a WRITE_ZEROES request, it asks
the underlying filesystem to punch out the range. This behavior is
correct if unmapping is allowed. However, a NOUNMAP request means that
the caller doesn't want us to free the storage backing the range, so
punching out the range is incorrect behavior.
To satisfy a NOUNMAP | WRITE_ZEROES request, loop should ask the
underlying filesystem to FALLOC_FL_ZERO_RANGE, which is (according to
the fallocate documentation) required to ensure that the entire range is
backed by real storage, which suffices for our purposes.
Fixes: 19372e2769 ("loop: implement REQ_OP_WRITE_ZEROES")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull MD changes from Song.
* 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md: no longer compare spare disk superblock events in super_load
md: improve handling of bio with REQ_PREFLUSH in md_flush_request()
md/bitmap: avoid race window between md_bitmap_resize and bitmap_file_clear_bit
md/raid0: Fix an error message in raid0_make_request()
We have a test case as follow:
mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] \
--assume-clean --bitmap=internal
mdadm -S /dev/md1
mdadm -A /dev/md1 /dev/sd[b-c] --run --force
mdadm --zero /dev/sda
mdadm /dev/md1 -a /dev/sda
echo offline > /sys/block/sdc/device/state
echo offline > /sys/block/sdb/device/state
sleep 5
mdadm -S /dev/md1
echo running > /sys/block/sdb/device/state
echo running > /sys/block/sdc/device/state
mdadm -A /dev/md1 /dev/sd[a-c] --run --force
When we readd /dev/sda to the array, it started to do recovery.
After offline the other two disks in md1, the recovery have
been interrupted and superblock update info cannot be written
to the offline disks. While the spare disk (/dev/sda) can continue
to update superblock info.
After stopping the array and assemble it, we found the array
run fail, with the follow kernel message:
[ 172.986064] md: kicking non-fresh sdb from array!
[ 173.004210] md: kicking non-fresh sdc from array!
[ 173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[ 173.022406] md1: failed to create bitmap (-5)
[ 173.023466] md: md1 stopped.
Since both sdb and sdc have the value of 'sb->events' smaller than
that in sda, they have been kicked from the array. However, the only
remained disk sda is in 'spare' state before stop and it cannot be
added to conf->mirrors[] array. In the end, raid array assemble
and run fail.
In fact, we can use the older disk sdb or sdc to assemble the array.
That means we should not choose the 'spare' disk as the fresh disk in
analyze_sbs().
To fix the problem, we do not compare superblock events when it is
a spare disk, as same as validate_super.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
If pers->make_request fails in md_flush_request(), the bio is lost. To
fix this, pass back a bool to indicate if the original make_request call
should continue to handle the I/O and instead of assuming the flush logic
will push it to completion.
Convert md_flush_request to return a bool and no longer calls the raid
driver's make_request function. If the return is true, then the md flush
logic has or will complete the bio and the md make_request call is done.
If false, then the md make_request function needs to keep processing like
it is a normal bio. Let the original call to md_handle_request handle any
need to retry sending the bio to the raid driver's make_request function
should it be needed.
Also mark md_flush_request and the make_request function pointer as
__must_check to issue warnings should these critical return values be
ignored.
Fixes: 2bc13b83e6 ("md: batch flush requests.")
Cc: stable@vger.kernel.org # # v4.19+
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
The first argument to WARN() is supposed to be a condition. The
original code will just print the mdname() instead of the full warning
message.
Fixes: c84a1372df ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
A zoned block device maintains a write pointer within a zone, and reads
beyond the write pointer are undefined. Fill data buffer returned above
the write pointer with 0xFF.
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch makes it possible to test blk_mq_update_nr_hw_queues() from
inside a VM.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce a local variable to make the code easier to read. This patch
does not change any functionality but makes the next patch in this
series easier to read.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In commit 4ed2863951 ("fs, elf: drop MAP_FIXED usage from elf_map") we
changed elf to use MAP_FIXED_NOREPLACE instead of MAP_FIXED for the
executable mappings.
Then, people reported that it broke some binaries that had overlapping
segments from the same file, and commit ad55eac74f ("elf: enforce
MAP_FIXED on overlaying elf segments") re-instated MAP_FIXED for some
overlaying elf segment cases. But only some - despite the summary line
of that commit, it only did it when it also does a temporary brk vma for
one obvious overlapping case.
Now Russell King reports another overlapping case with old 32-bit x86
binaries, which doesn't trigger that limited case. End result: we had
better just drop MAP_FIXED_NOREPLACE entirely, and go back to MAP_FIXED.
Yes, it's a sign of old binaries generated with old tool-chains, but we
do pride ourselves on not breaking existing setups.
This still leaves MAP_FIXED_NOREPLACE in place for the load_elf_interp()
and the old load_elf_library() use-cases, because nobody has reported
breakage for those. Yet.
Note that in all the cases seen so far, the overlapping elf sections
seem to be just re-mapping of the same executable with different section
attributes. We could possibly introduce a new MAP_FIXED_NOFILECHANGE
flag or similar, which acts like NOREPLACE, but allows just remapping
the same executable file using different protection flags.
It's not clear that would make a huge difference to anything, but if
people really hate that "elf remaps over previous maps" behavior, maybe
at least a more limited form of remapping would alleviate some concerns.
Alternatively, we should take a look at our elf_map() logic to see if we
end up not mapping things properly the first time.
In the meantime, this is the minimal "don't do that then" patch while
people hopefully think about it more.
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: 4ed2863951 ("fs, elf: drop MAP_FIXED usage from elf_map")
Fixes: ad55eac74f ("elf: enforce MAP_FIXED on overlaying elf segments")
Cc: Michal Hocko <mhocko@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- revert an incorret hunk from a patch that caused problems
on various arm boards (Andrey Smirnov)
-----BEGIN PGP SIGNATURE-----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=kS6W
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.4-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping regression fix from Christoph Hellwig:
"Revert an incorret hunk from a patch that caused problems on various
arm boards (Andrey Smirnov)"
* tag 'dma-mapping-5.4-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: fix false positive warnings in dma_common_free_remap()
A few fixes this time around:
- Fixup of some clock specifications for DRA7 (device-tree fix)
- Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
warnings at boot
- A few more minor fixups for OMAPs, most around display
- Enable STM32 QSPI as =y since their rootfs sometimes comes from
there
- Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool
- Fix of thermal zone definition for ux500 (5.4 regression)
-----BEGIN PGP SIGNATURE-----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=+lB0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes this time around:
- Fixup of some clock specifications for DRA7 (device-tree fix)
- Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
warnings at boot
- A few more minor fixups for OMAPs, most around display
- Enable STM32 QSPI as =y since their rootfs sometimes comes from
there
- Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool
- Fix of thermal zone definition for ux500 (5.4 regression)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: multi_v7_defconfig: Fix SPI_STM32_QSPI support
ARM: dts: ux500: Fix up the CPU thermal zone
arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to y
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
- remove unneeded ar-option and KBUILD_ARFLAGS
- remove long-deprecated SUBDIRS
- fix modpost to suppress false-positive warnings for UML builds
- fix namespace.pl to handle relative paths to ${objtree}, ${srctree}
- make setlocalversion work for /bin/sh
- make header archive reproducible
- fix some Makefiles and documents
-----BEGIN PGP SIGNATURE-----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=fSXc
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- remove unneeded ar-option and KBUILD_ARFLAGS
- remove long-deprecated SUBDIRS
- fix modpost to suppress false-positive warnings for UML builds
- fix namespace.pl to handle relative paths to ${objtree}, ${srctree}
- make setlocalversion work for /bin/sh
- make header archive reproducible
- fix some Makefiles and documents
* tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kheaders: make headers archive reproducible
kbuild: update compile-test header list for v5.4-rc2
kbuild: two minor updates for Documentation/kbuild/modules.rst
scripts/setlocalversion: clear local variable to make it work for sh
namespace: fix namespace.pl script to support relative paths
video/logo: do not generate unneeded logo C files
video/logo: remove unneeded *.o pattern from clean-files
integrity: remove pointless subdir-$(CONFIG_...)
integrity: remove unneeded, broken attempt to add -fshort-wchar
modpost: fix static EXPORT_SYMBOL warnings for UML build
kbuild: correct formatting of header in kbuild module docs
kbuild: remove SUBDIRS support
kbuild: remove ar-option and KBUILD_ARFLAGS
Twelve patches mostly small but obvious fixes or cosmetic but small
updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXZgfWiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaVOAQDnuANx
QGEuQ1dZPALeZPOlEOsJzzpHPd3O+mQauIE96wD9FMypt/UKF9+fvlp4mCP+ya66
0fz1kmTQIcAADdYaNYM=
=aQi7
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twelve patches mostly small but obvious fixes or cosmetic but small
updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix Nport ID display value
scsi: qla2xxx: Fix N2N link up fail
scsi: qla2xxx: Fix N2N link reset
scsi: qla2xxx: Optimize NPIV tear down process
scsi: qla2xxx: Fix stale mem access on driver unload
scsi: qla2xxx: Fix unbound sleep in fcport delete path.
scsi: qla2xxx: Silence fwdump template message
scsi: hisi_sas: Make three functions static
scsi: megaraid: disable device when probe failed after enabled device
scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue
scsi: qedf: Remove always false 'tmp_prio < 0' statement
scsi: ufs: skip shutdown if hba is not powered
scsi: bnx2fc: Handle scope bits when array returns BUSY or TSF
This makes getdents() and getdents64() do sanity checking on the
pathname that it gives to user space. And to mitigate the performance
impact of that, it first cleans up the way it does the user copying, so
that the code avoids doing the SMAP/PAN updates between each part of the
dirent structure write.
I really wanted to do this during the merge window, but didn't have
time. The conversion of filldir to unsafe_put_user() is something I've
had around for years now in a private branch, but the extra pathname
checking finally made me clean it up to the point where it is mergable.
It's worth noting that the filename validity checking really should be a
bit smarter: it would be much better to delay the error reporting until
the end of the readdir, so that non-corrupted filenames are still
returned. But that involves bigger changes, so let's see if anybody
actually hits the corrupt directory entry case before worrying about it
further.
* branch 'readdir':
Make filldir[64]() verify the directory entry filename is valid
Convert filldir[64]() from __put_user() to unsafe_put_user()
This has been discussed several times, and now filesystem people are
talking about doing it individually at the filesystem layer, so head
that off at the pass and just do it in getdents{64}().
This is partially based on a patch by Jann Horn, but checks for NUL
bytes as well, and somewhat simplified.
There's also commentary about how it might be better if invalid names
due to filesystem corruption don't cause an immediate failure, but only
an error at the end of the readdir(), so that people can still see the
filenames that are ok.
There's also been discussion about just how much POSIX strictly speaking
requires this since it's about filesystem corruption. It's really more
"protect user space from bad behavior" as pointed out by Jann. But
since Eric Biederman looked up the POSIX wording, here it is for context:
"From readdir:
The readdir() function shall return a pointer to a structure
representing the directory entry at the current position in the
directory stream specified by the argument dirp, and position the
directory stream at the next entry. It shall return a null pointer
upon reaching the end of the directory stream. The structure dirent
defined in the <dirent.h> header describes a directory entry.
From definitions:
3.129 Directory Entry (or Link)
An object that associates a filename with a file. Several directory
entries can associate names with the same file.
...
3.169 Filename
A name consisting of 1 to {NAME_MAX} bytes used to name a file. The
characters composing the name may be selected from the set of all
character values excluding the slash character and the null byte. The
filenames dot and dot-dot have special meaning. A filename is
sometimes referred to as a 'pathname component'."
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
Also note that if this ends up being noticeable as a performance
regression, we can fix that to do a much more optimized model that
checks for both NUL and '/' at the same time one word at a time.
We haven't really tended to optimize 'memchr()', and it only checks for
one pattern at a time anyway, and we really _should_ check for NUL too
(but see the comment about "soft errors" in the code about why it
currently only checks for '/')
See the CONFIG_DCACHE_WORD_ACCESS case of hash_name() for how the name
lookup code looks for pathname terminating characters in parallel.
Link: https://lore.kernel.org/lkml/20190118161440.220134-2-jannh@google.com/
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
