Commit Graph

796173 Commits

Author SHA1 Message Date
Jeff Barnhill
6915ed86cc net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.

Fixes: 2384d02520 ("net/ipv6: Add anycast addresses to a global hashtable")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-05 13:36:27 -08:00
Jarod Wilson
ea53abfab9 bonding/802.3ad: fix link_failure_count tracking
Commit 4d2c0cda07 set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.

Fixes: 4d2c0cda07 ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-04 16:44:44 -08:00
Holger Hoffstätte
0432e83319 net: phy: realtek: fix RTL8201F sysfs name
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:

$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]

Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").

Fix this by removing the offending slash in the driver name.

Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.

Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-04 16:43:17 -08:00
Xin Long
12480e3b16 sctp: define SCTP_SS_DEFAULT for Stream schedulers
According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.

SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.

Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 19:40:29 -07:00
Xin Long
fd82d61ba1 sctp: fix strchange_flags name for Stream Change Event
As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.

To keep the compatibility, fix it by adding two macros.

Fixes: b444153fb5 ("sctp: add support for generating add stream change event notification")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 19:38:08 -07:00
David S. Miller
1e2d3c4929 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:

====================
pull-request: bpf 2018-11-03

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
   to not use page start but actual start instead to work correctly with
   profiling e.g. finding hot instructions from stack traces. Also fix latter
   with regards to dumping address and jited len for !multi prog, from Song.

2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
   instead of leaving the user provided length, from Daniel.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 19:33:35 -07:00
Shalom Toledo
96801552f8 mlxsw: spectrum: Fix IP2ME CPU policer configuration
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.

Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.

Fixes: 9148e7cf73 ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 19:31:42 -07:00
Arnd Bergmann
a277d516de openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
When CONFIG_CC_OPTIMIZE_FOR_DEBUGGING is enabled, the compiler
fails to optimize out a dead code path, which leads to a link failure:

net/openvswitch/conntrack.o: In function `ovs_ct_set_labels':
conntrack.c:(.text+0x2e60): undefined reference to `nf_connlabels_replace'

In this configuration, we can take a shortcut, and completely
remove the contrack label code. This may also help the regular
optimization.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 19:28:44 -07:00
Arnd Bergmann
9261921052 qed: fix link config error handling
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:

drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]

When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.

Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 19:27:33 -07:00
Yunsheng Lin
e8ccbb7d2f net: hns3: Fix for out-of-bounds access when setting pfc back pressure
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.

[   35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14

[   35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[   35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[   35.254141] Workqueue: events work_for_cpu_fn
[   35.254144] Call trace:
[   35.254147]  dump_backtrace+0x0/0x2f0
[   35.254149]  show_stack+0x24/0x30
[   35.254154]  dump_stack+0x110/0x184
[   35.254157]  print_address_description+0x168/0x2b0
[   35.254160]  kasan_report+0x184/0x310
[   35.254162]  __asan_load2+0x7c/0xa0
[   35.254170]  hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254177]  hclge_tm_init_hw+0x794/0x9f0 [hclge]
[   35.254184]  hclge_tm_schd_init+0x48/0x58 [hclge]
[   35.254191]  hclge_init_ae_dev+0x778/0x1168 [hclge]
[   35.254196]  hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[   35.254206]  hns3_probe+0x88/0xa8 [hns3]
[   35.254210]  local_pci_probe+0x7c/0xf0
[   35.254212]  work_for_cpu_fn+0x34/0x50
[   35.254214]  process_one_work+0x4d4/0xa38
[   35.254216]  worker_thread+0x55c/0x8d8
[   35.254219]  kthread+0x1b0/0x1b8
[   35.254222]  ret_from_fork+0x10/0x1c

[   35.254224] The buggy address belongs to the page:
[   35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[   35.273835] flags: 0xfffff8000008000(head)
[   35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[   35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[   35.282012] page dumped because: kasan: bad access detected

[   35.282014] Memory state around the buggy address:
[   35.282017]  ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282019]  ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282022]                             ^
[   35.282024]  ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282026]  ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282028] ==================================================================
[   35.282029] Disabling lock debugging due to kernel taint
[   35.282747] hclge driver initialization finished.

Fixes: 67bf2541f4 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 15:41:58 -07:00
David S. Miller
cb53fd54e3 Merge branch 'net-bql-better-deal-with-GSO'
Eric Dumazet says:

====================
net: bql: better deal with GSO

While BQL bulk dequeue works well for TSO packets, it is
not very efficient as soon as GSO is involved.

On a GSO only workload (UDP or TCP), this patch series
can save about 8 % of cpu cycles on a 40Gbit mlx4 NIC,
by keeping optimal batching, and avoiding expensive
doorbells, qdisc requeues and reschedules.

This patch series :

- Add __netdev_tx_sent_queue() so that drivers
  can implement efficient BQL and xmit_more support.

- Implement a work around in dev_hard_start_xmit()
  for drivers not using __netdev_tx_sent_queue()

- changes mlx4 to use __netdev_tx_sent_queue()

v2: Tariq and Willem feedback addressed.
    added __netdev_tx_sent_queue() (Willem suggestion)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 15:40:01 -07:00
Eric Dumazet
c297344435 net/mlx4_en: use __netdev_tx_sent_queue()
doorbell only depends on xmit_more and netif_tx_queue_stopped()

Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.

This patch increases performance on GSO workload by keeping
doorbells to the minimum required.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 15:40:01 -07:00
Eric Dumazet
fe60faa506 net: do not abort bulk send on BQL status
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.

Problem is that GSO packets can end up comsuming more than
the BQL budget.

Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.

It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.

It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.

Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 15:40:01 -07:00
Eric Dumazet
3e59020abf net: bql: add __netdev_tx_sent_queue()
When qdisc_run() tries to use BQL budget to bulk-dequeue a batch
of packets, GSO can later transform this list in another list
of skbs, and each skb is sent to device ndo_start_xmit(),
one at a time, with skb->xmit_more being set to one but
for last skb.

Problem is that very often, BQL limit is hit in the middle of
the packet train, forcing dev_hard_start_xmit() to stop the
bulk send and requeue the end of the list.

BQL role is to avoid head of line blocking, making sure
a qdisc can deliver high priority packets before low priority ones.

But there is no way requeued packets can be bypassed by fresh
packets in the qdisc.

Aborting the bulk send increases TX softirqs, and hot cache
lines (after skb_segment()) are wasted.

Note that for TSO packets, we never split a packet in the middle
because of BQL limit being hit.

Drivers should be able to update BQL counters without
flipping/caring about BQL status, if the current skb
has xmit_more set.

Upper layers are ultimately responsible to stop sending another
packet train when BQL limit is hit.

Code template in a driver might look like the following :

	send_doorbell = __netdev_tx_sent_queue(tx_queue, nr_bytes, skb->xmit_more);

Note that __netdev_tx_sent_queue() use is not mandatory,
since following patch will change dev_hard_start_xmit()
to not care about BQL status.

But it is highly recommended so that xmit_more full benefits
can be reached (less doorbells sent, and less atomic operations as well)

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 15:40:01 -07:00
David S. Miller
b8a5d06ae2 Merge branch 's390-qeth-fixes'
Julian Wiedmann says:

====================
s390/qeth: fixes 2018-11-02

please apply one round of qeth fixes for -net.

Patch 1 is rather large and removes a use-after-free hazard from many of our
debug trace entries.
Patch 2 is yet another fix-up for the L3 subdriver's new IP address management
code.
Patch 3 and 4 resolve some fallout from the recent changes wrt how/when qeth
allocates its net_device.
Patch 5 makes sure we don't set reserved bits when building HW commands from
user-provided data.
And finally, patch 6 allows ethtool to play nice with new HW.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 10:44:06 -07:00
Julian Wiedmann
54e049c227 s390/qeth: report 25Gbit link speed
This adds the various identifiers for 25Gbit cards, and wires them up
into sysfs and ethtool.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 10:44:06 -07:00
Julian Wiedmann
125d7d3011 s390/qeth: sanitize ARP requests
The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.

This also sets the correct command length for ARP_REMOVE_ENTRY.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 10:44:06 -07:00
Julian Wiedmann
9fae5c3b60 s390/qeth: fix initial operstate
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.

Fixes: 91cc98f51e ("s390/qeth: remove duplicated carrier state tracking")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 10:44:05 -07:00
Julian Wiedmann
30356d0815 s390/qeth: unregister netdevice only when registered
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.

Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.

Fixes: d3d1b205e8 ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 10:44:05 -07:00
Julian Wiedmann
bd74a7f9cc s390/qeth: fix HiperSockets sniffer
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.

While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
   without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
   is switched off later we can operate just like normal.

Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 10:44:05 -07:00
Julian Wiedmann
e19e5be8b4 s390/qeth: sanitize strings in debug messages
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.

So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 10:44:05 -07:00
David S. Miller
265ad0632f Merge branch 'net-timeout-fixes-for-GENET-and-SYSTEMPORT'
Florian Fainelli says:

====================
net: timeout fixes for GENET and SYSTEMPORT

This patch series fixes occasional transmit timeout around the time
the system goes into suspend. GENET and SYSTEMPORT have nearly the same
logic in that regard and were both affected in the same way.

Please queue up for stable, thanks!
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 00:03:40 -07:00
Florian Fainelli
7cb6a2a2c7 net: systemport: Protect stop from timeout
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.

The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.

This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.

The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.

The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.

These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.

For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.

Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 00:03:40 -07:00
Doug Berger
09e805d257 net: bcmgenet: protect stop from timeout
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.

The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.

This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.

The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.

The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.

These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.

For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.

Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-03 00:03:39 -07:00
David Howells
c7e86acfce rxrpc: Fix lockup due to no error backoff after ack transmit error
If the network becomes (partially) unavailable, say by disabling IPv6, the
background ACK transmission routine can get itself into a tizzy by
proposing immediate ACK retransmission.  Since we're in the call event
processor, that happens immediately without returning to the workqueue
manager.

The condition should clear after a while when either the network comes back
or the call times out.

Fix this by:

 (1) When re-proposing an ACK on failed Tx, don't schedule it immediately.
     This will allow a certain amount of time to elapse before we try
     again.

 (2) Enforce a return to the workqueue manager after a certain number of
     iterations of the call processing loop.

 (3) Add a backoff delay that increases the delay on deferred ACKs by a
     jiffy per failed transmission to a limit of HZ.  The backoff delay is
     cleared on a successful return from kernel_sendmsg().

 (4) Cancel calls immediately if the opening sendmsg fails.  The layer
     above can arrange retransmission or rotate to another server.

Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-02 23:59:26 -07:00
Tristram Ha
284fb78ed7 net: dsa: microchip: initialize mutex before use
Initialize mutex before use.  Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.

Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-02 23:56:34 -07:00
Jeff Barnhill
2384d02520 net/ipv6: Add anycast addresses to a global hashtable
icmp6_send() function is expensive on systems with a large number of
interfaces. Every time it’s called, it has to verify that the source
address does not correspond to an existing anycast address by looping
through every device and every anycast address on the device.  This can
result in significant delays for a CPU when there are a large number of
neighbors and ND timers are frequently timing out and calling
neigh_invalidate().

Add anycast addresses to a global hashtable to allow quick searching for
matching anycast addresses.  This is based on inet6_addr_lst in addrconf.c.

Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-02 23:54:56 -07:00
Frieder Schrempf
7b900ead6c usbnet: smsc95xx: disable carrier check while suspending
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.

Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-02 23:49:15 -07:00
Mathieu Malaterre
49682bfa1e net: document skb parameter in function 'skb_gso_size_check'
Remove kernel-doc warning:

  net/core/skbuff.c:4953: warning: Function parameter or member 'skb' not described in 'skb_gso_size_check'

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-02 23:34:37 -07:00
Daniel Borkmann
28c2fae726 bpf: fix bpf_prog_get_info_by_fd to return 0 func_lens for unpriv
While dbecd73884 ("bpf: get kernel symbol addresses via syscall")
zeroed info.nr_jited_ksyms in bpf_prog_get_info_by_fd() for queries
from unprivileged users, commit 815581c11c ("bpf: get JITed image
lengths of functions via syscall") forgot about doing so and therefore
returns the #elems of the user set up buffer which is incorrect. It
also needs to indicate a info.nr_jited_func_lens of zero.

Fixes: 815581c11c ("bpf: get JITed image lengths of functions via syscall")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Sandipan Das <sandipan@linux.vnet.ibm.com>
Cc: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-11-02 13:51:15 -07:00
Daniel Borkmann
b0970f235f Merge branch 'bpf-accurate-prog-addr'
Song Liu says:

====================
Changes v1 -> v2:
1. Added main program length to bpf_prog_info->jited_fun_lens (3/3).
2. Updated commit message of 1/3 and 2/3 with more background about the
   address masking, and why it is still save after the changes.
3. Replace "ulong" with "unsigned long".

This set improves bpf program address showed in /proc/kallsyms and in
bpf_prog_info. First, real program address is showed instead of page
address. Second, when there is no subprogram, bpf_prog_info->jited_ksyms
and bpf_prog_info->jited_fun_lens returns the main prog address and
length.
====================

Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-11-02 21:39:03 +01:00
Song Liu
ff1889fc53 bpf: show main program address and length in bpf_prog_info
Currently, when there is no subprog (prog->aux->func_cnt == 0),
bpf_prog_info does not return any jited_ksyms or jited_func_lens. This
patch adds main program address (prog->bpf_func) and main program
length (prog->jited_len) to bpf_prog_info.

Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-11-02 21:39:01 +01:00
Song Liu
de57e99ceb bpf: show real jited address in bpf_prog_info->jited_ksyms
Currently, jited_ksyms in bpf_prog_info shows page addresses of jited
bpf program. The main reason here is to not expose randomized start
address. However, this is not ideal for detailed profiling (find hot
instructions from stack traces). This patch replaces the page address
with real prog start address.

This change is OK because bpf_prog_get_info_by_fd() is only available
to root.

Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-11-02 21:39:01 +01:00
Song Liu
df0734702a bpf: show real jited prog address in /proc/kallsyms
Currently, /proc/kallsyms shows page address of jited bpf program. The
main reason here is to not expose randomized start address. However,
This is not ideal for detailed profiling (find hot instructions from
stack traces). This patch replaces the page address with real prog start
address.

This change is OK because these addresses are still protected by sysctl
kptr_restrict (see kallsyms_show_value()), and only programs loaded by
root are added to kallsyms (see bpf_prog_kallsyms_add()).

Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-11-02 21:39:01 +01:00
Cong Wang
7de414a9dd net: drop skb on failure in ip_check_defrag()
Most callers of pskb_trim_rcsum() simply drop the skb when
it fails, however, ip_check_defrag() still continues to pass
the skb up to stack. This is suspicious.

In ip_check_defrag(), after we learn the skb is an IP fragment,
passing the skb to callers makes no sense, because callers expect
fragments are defrag'ed on success. So, dropping the skb when we
can't defrag it is reasonable.

Note, prior to commit 88078d98d1, this is not a big problem as
checksum will be fixed up anyway. After it, the checksum is not
correct on failure.

Found this during code review.

Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-01 13:55:30 -07:00
Linus Torvalds
7c6c54b505 Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
 "I2C has a core bugfix & cleanup as well as an ID addition and
  MAINTAINERS update for you"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add maintainer for IMX LPI2C driver
  dt-bindings: i2c: i2c-imx-lpi2c: add imx8qxp compatible string
  i2c: Clear client->irq in i2c_device_remove
  i2c: Remove unnecessary call to irq_find_mapping
2018-11-01 09:31:19 -07:00
Linus Torvalds
6444ccfd69 Merge branch 'for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu
Pull percpu fixes from Dennis Zhou:
 "Two small things for v4.20.

  The first fixes a clang uninitialized variable warning for arm64 in
  the default path calls BUILD_BUG(). The second removes an unnecessary
  unlikely() in a WARN_ON() use"

* 'for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
  arm64: percpu: Initialize ret in the default case
  mm: percpu: remove unnecessary unlikely()
2018-11-01 09:27:57 -07:00
Linus Torvalds
82aa467151 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) BPF verifier fixes from Daniel Borkmann.

 2) HNS driver fixes from Huazhong Tan.

 3) FDB only works for ethernet devices, reject attempts to install FDB
    rules for others. From Ido Schimmel.

 4) Fix spectre V1 in vhost, from Jason Wang.

 5) Don't pass on-stack object to irq_set_affinity_hint() in mvpp2
    driver, from Marc Zyngier.

 6) Fix mlx5e checksum handling when RXFCS is enabled, from Eric
    Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (49 commits)
  openvswitch: Fix push/pop ethernet validation
  net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
  bpf: test make sure to run unpriv test cases in test_verifier
  bpf: add various test cases to test_verifier
  bpf: don't set id on after map lookup with ptr_to_map_val return
  bpf: fix partial copy of map_ptr when dst is scalar
  libbpf: Fix compile error in libbpf_attach_type_by_name
  kselftests/bpf: use ping6 as the default ipv6 ping binary if it exists
  selftests: mlxsw: qos_mc_aware: Add a test for UC awareness
  selftests: mlxsw: qos_mc_aware: Tweak for min shaper
  mlxsw: spectrum: Set minimum shaper on MC TCs
  mlxsw: reg: QEEC: Add minimum shaper fields
  net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()
  net: hns3: bugfix for rtnl_lock's range in the hclge_reset()
  net: hns3: bugfix for handling mailbox while the command queue reinitialized
  net: hns3: fix incorrect return value/type of some functions
  net: hns3: bugfix for hclge_mdio_write and hclge_mdio_read
  net: hns3: bugfix for is_valid_csq_clean_head()
  net: hns3: remove unnecessary queue reset in the hns3_uninit_all_ring()
  net: hns3: bugfix for the initialization of command queue's spin lock
  ...
2018-11-01 09:16:01 -07:00
Linus Torvalds
ffb845db50 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
 "Two small fixes"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Wire up compat getpeername and getsockname.
  sparc64: Remvoe set_fs() from perf_callchain_user().
2018-11-01 09:07:04 -07:00
Linus Torvalds
5c99a8d1ed csky: dtb Kbuild fixup patches for linux-4.20-rc1
These patches are complementary to "C-SKY(csky) Port for Linux 4.20" and
 fixup dtb Kbuild to follow the new Devicetree dtb build rules.
 
 Link: https://lore.kernel.org/lkml/CABGGisxiWaQn9qDqpfxEWcckkGJfMzFvSPGvuhQK7oB404-6DQ@mail.gmail.com/
 Signed-off-by: Guo Ren <ren_guo@c-sky.com>
 -----BEGIN PGP SIGNATURE-----
 
 iQJGBAABCAAwFiEE2KAv+isbWR/viAKHAXH1GYaIxXsFAlvadMUSHHJlbl9ndW9A
 Yy1za3kuY29tAAoJEAFx9RmGiMV7fN4P/ieygi8RlzFF5PEggQEt1PdvGnte2Kx/
 UUqlX7ZrY/ZY8p/XaG8p0YlWx236YcZoQtTJT4ThVuAFyywuIjR96kWlKwVjeKC2
 /lfXvQrJRSjzQAQU2zRe+KMEvsEw0qEO9WWqV8pORt+t1ZjE59mFov2iK+mcS22R
 T12Djp7V9RYr33KFcu8BQ8g4524t9x3MSGVz+AB/D+cni8XSS3dkg5QlTWo+LGfS
 pHAISI3t1AftXkQ3HRpDKFs9Equ0CX3wm129j6awWHbYBpXsdwUW81fr+KMNgdd/
 s59wcdRInksww5ZaAvtgfxYJeTTyu488KMEMhagDNn3n0El61ui0vncmvPebnmjB
 FQb4v6AvH69V2aN3/xAKuov4EfELoFUc/E0z3GJk//58d6kshMdyI++QB2CFZ8IS
 TqHSkkEKCpThTyJavGuS0Jvkj7vpneW5iDFQwWN0RqIub7PnC6Aa0uSw+/G7Pq/5
 SY2zhEJ0o6waBuQR5IEYzxvRwlU3hNuqXe7/if4kqw/LQUFTydKX7eQAcrSTLlnI
 /jxrXH7vaymhD9/wI58GPIsqaRObln92uaUWHpjQqKPXdnemv60dSta2LLkdY4Le
 MVsTc412nkFjt4Ft+uOrcJQnVsK48RTh56vBB44zxONoK9tUz0y6wgIEyebwzRSy
 uYaZ6t0jj7A3
 =TO13
 -----END PGP SIGNATURE-----

Merge tag 'csky-for-linus-4.20-fixup-dtb' of https://github.com/c-sky/csky-linux

Pull csky dtb fixups from Guo Ren:
 "These fix the csky dtb Kbuild to follow the new Devicetree dtb build
  rules"

* tag 'csky-for-linus-4.20-fixup-dtb' of https://github.com/c-sky/csky-linux:
  csky: use common dtb build rules
  csky: remove builtin-dtb Kbuild
2018-11-01 09:04:30 -07:00
Linus Torvalds
eb7046e9bf platform-drivers-x86 for v4.20-1
Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86 as
 they are closely coupled with other drivers in this location.
 
 Improve _init* usage for acerhdf and fix some usage issues with messages
 and module parameters.
 
 Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
 workqueue overhead, eliminate double reporting of keyboard backlight.
 
 Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
 
 Notify intel_telemetry users when IPC1 device is not enabled.
 
 Update various drivers with new laptop model IDs.
 
 Update several intel drivers to use SPDX identifers and order headers
 alphabetically.
 
 The following is an automated git shortlog grouped by driver:
 
 Add Intel AtomISP2 dummy / power-management driver:
  - Add Intel AtomISP2 dummy / power-management driver
 
 lg-laptop:
  - Add LG Gram laptop special features driver
 
 HID:
  -  asus: only support backlight when it's not driven by WMI
 
 MAINTAINERS:
  -  intel_telemetry: Update maintainers info
  -  intel_pmc_core: Update MAINTAINERS
  -  Update maintainer for dcdbas and dell_rbu
  -  Use my infradead account exclusively for PDx86 work
 
 acerhdf:
  -  restructure to allow large BIOS table be __initconst
  -  mark appropriate content with __init prefix
  -  Add BIOS entry for Gateway LT31 v1.3307
  -  Remove cut-and-paste trap from instructions
  -  Enable ability to list supported systems
  -  clarify modinfo messages for BIOS override
 
 asus-wmi:
  -  export function for evaluating WMI methods
  -  Only notify kbd LED hw_change by fn-key pressed
  -  Simplify the keyboard brightness updating process
 
 firmware:
  -  dcdbas: include linux/io.h
  -  dcdbas: Move dcdbas to drivers/platform/x86
  -  dell_rbu: Move dell_rbu to drivers/platform/x86
  -  dcdbas: Add support for WSMT ACPI table
  -  dell_rbu: Make payload memory uncachable
 
 ideapad-laptop:
  -  Add Y530-15ICH to no_hw_rfkill
  -  Use __func__ instead of read_ec_cmd in pr_err
 
 intel-hid:
  -  Convert to use SPDX identifier
 
 intel-ips:
  -  Convert to use SPDX identifier
 
 intel-rst:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel-smartconnect:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel-wmi-thunderbolt:
  -  Add dynamic debugging
  -  Convert to use SPDX identifier
 
 intel_bxtwc_tmu:
  -  Convert to use SPDX identifier
 
 intel_cht_int33fe:
  -  Convert to use SPDX identifier
 
 intel_chtdc_ti_pwrbtn:
  -  Add SPDX identifier
 
 intel_int0002_vgpio:
  -  Convert to use SPDX identifier
  -  Implement irq_set_wake
  -  Enable the driver on Bay Trail platforms
 
 intel_menlow:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel_mid_powerbtn:
  -  Convert to use SPDX identifier
  -  Remove unnecessary init.h inclusion
  -  Get rid of custom ICPU() macro
 
 intel_mid_thermal:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel_oaktrail:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel_pmc:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel_punit_ipc:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel_scu_ipc:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 intel_telemetry:
  -  Get rid of custom macro
  -  report debugfs failure
  -  Convert to use SPDX identifier
 
 intel_turbo_max_3:
  -  Convert to use SPDX identifier
  -  Sort headers alphabetically
 
 mlx-platform:
  -  Properly use mlxplat_mlxcpld_msn201x_items
 
 touchscreen_dmi:
  -  Add min-x and min-y settings for various models
  -  Add info for the Onda V80 Plus v3 tablet
  -  Add info for the Trekstor Primetab T13B tablet
  -  Add info for the Trekstor Primebook C11 convertible
 
 tracing:
  -  Trivia spelling fix containerof() -> container_of()
 
 wmi:
  -  declare device_type structure as constant
 -----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJb2mDCAAoJEKbMaAwKp364KdkH/Rar8cenw7uFeVzT5o4fGzTn
 0Oo1Pnwh+hPgmQwmf8O/mHsa/1Zb9nX4nNLU/ysDUjAAZ9wZLoB57HlImQquPA74
 c8lXTz5MVF140WB1f1Ck5PmeonJR2Xve7HTYCoBmGo71jOxHxCgJbp1Giiho0Imd
 3NXzzahEnAiy/L5PhqqYTmIfTeAHQ2Fo7GkHCjMnS20FP2fBtvPrc7db03F+FZ4y
 QTfbT0oR42NdeW21AbCRGY3P47axB3xDJX4LOYrb4uo4CIzd1yatlHk407NRRyv8
 pab6aeJR23FouA/tcvv+T36D3vqRw78e6BWdoyowWOd7CUOgjtSC3lKGzfT6hSY=
 =0BDZ
 -----END PGP SIGNATURE-----

Merge tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:

 - Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86
   as they are closely coupled with other drivers in this location.

 - Improve _init* usage for acerhdf and fix some usage issues with
   messages and module parameters.

 - Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
   workqueue overhead, eliminate double reporting of keyboard backlight.

 - Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).

 - Notify intel_telemetry users when IPC1 device is not enabled.

 - Update various drivers with new laptop model IDs.

 - Update several intel drivers to use SPDX identifers and order headers
   alphabetically.

* tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
  HID: asus: only support backlight when it's not driven by WMI
  platform/x86: asus-wmi: export function for evaluating WMI methods
  platform/x86: asus-wmi: Only notify kbd LED hw_change by fn-key pressed
  platform/x86: wmi: declare device_type structure as constant
  platform/x86: ideapad: Add Y530-15ICH to no_hw_rfkill
  platform/x86: Add Intel AtomISP2 dummy / power-management driver
  platform/x86: touchscreen_dmi: Add min-x and min-y settings for various models
  platform/x86: touchscreen_dmi: Add info for the Onda V80 Plus v3 tablet
  platform/x86: touchscreen_dmi: Add info for the Trekstor Primetab T13B tablet
  platform/x86: intel_telemetry: Get rid of custom macro
  platform/x86: intel_telemetry: report debugfs failure
  MAINTAINERS: intel_telemetry: Update maintainers info
  platform/x86: Add LG Gram laptop special features driver
  platform/x86: asus-wmi: Simplify the keyboard brightness updating process
  platform/x86: touchscreen_dmi: Add info for the Trekstor Primebook C11 convertible
  platform/x86: mlx-platform: Properly use mlxplat_mlxcpld_msn201x_items
  MAINTAINERS: intel_pmc_core: Update MAINTAINERS
  firmware: dcdbas: include linux/io.h
  platform/x86: intel-wmi-thunderbolt: Add dynamic debugging
  platform/x86: intel-wmi-thunderbolt: Convert to use SPDX identifier
  ...
2018-11-01 08:42:21 -07:00
Guo Ren
e8d0c9a726 csky: use common dtb build rules
Remove the Kbuild rules in arch/csky and use common dtb build rules.

This modification is based on:

commit 37c8a5fafa ("kbuild: consolidate Devicetree dtb build rules")

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2018-11-01 10:52:27 +08:00
Guo Ren
c4c14c3bd1 csky: remove builtin-dtb Kbuild
Remove the builtin-dtb implementation in arch/csky.

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2018-11-01 10:52:26 +08:00
Jaime Caamaño Ruiz
46ebe2834b openvswitch: Fix push/pop ethernet validation
When there are both pop and push ethernet header actions among the
actions to be applied to a packet, an unexpected EINVAL (Invalid
argument) error is obtained. This is due to mac_proto not being reset
correctly when those actions are validated.

Reported-at:
https://mail.openvswitch.org/pipermail/ovs-discuss/2018-October/047554.html
Fixes: 91820da6ae ("openvswitch: add Ethernet push and pop actions")
Signed-off-by: Jaime Caamaño Ruiz <jcaamano@suse.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-31 18:37:16 -07:00
Niklas Cassel
30549aab14 net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.

When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().

Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.

Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.

Fix this by using "#if IS_ENABLED()" instead of "#if defined()".

Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-31 18:35:58 -07:00
David S. Miller
1f2b5b8e2d sparc64: Wire up compat getpeername and getsockname.
Fixes: 8b30ca73b7 ("sparc: Add all necessary direct socket system calls.")
Reported-by: Joseph Myers  <joseph@codesourcery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-31 18:30:21 -07:00
David S. Miller
4d3163cf87 Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2018-10-31

This series contains a various collection of fixes.

Miroslav Lichvar from Red Hat or should I say IBM now?  Updates the PHC
timecounter interval for igb so that it gets updated at least once
every 550 seconds.

Ngai-Mint provides a fix for fm10k to prevent a soft lockup or system
crash by adding a new condition to determine if the SM mailbox is in the
correct state before proceeding.

Jake provides several fm10k fixes, first one marks complier aborts as
non-fatal since on some platforms trigger machine check errors when the
compile aborts.  Added missing device ids to the in-kernel driver.  Due
to the recent fixes, bumped the driver version.

I (Jeff Kirsher) fixed a XFRM_ALGO dependency for both ixgbe and
ixgbevf.  This fix was based on the original work from Arnd Bergmann,
which only fixed ixgbe.

Mitch provides a fix for i40e/avf to update the status codes, which
resolves an issue between a mis-match between i40e and the iavf driver,
which also supports the ice LAN driver.

Radoslaw fixes the ixgbe where the driver is logging a message about
spoofed packets detected when the VF is re-started with a different MAC
address.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-31 18:21:37 -07:00
David S. Miller
df975da4e5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:

====================
pull-request: bpf 2018-11-01

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix tcp_bpf_recvmsg() to return -EAGAIN instead of 0 in non-blocking
   case when no data is available yet, from John.

2) Fix a compilation error in libbpf_attach_type_by_name() when compiled
   with clang 3.8, from Andrey.

3) Fix a partial copy of map pointer on scalar alu and remove id
   generation for RET_PTR_TO_MAP_VALUE return types, from Daniel.

4) Add unlimited memlock limit for kernel selftest's flow_dissector_load
   program, from Yonghong.

5) Fix ping for some BPF shell based kselftests where distro does not
   ship "ping -6" anymore, from Li.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-31 17:34:08 -07:00
Alexei Starovoitov
dfeb8f4c96 Merge branch 'verifier-fixes'
Daniel Borkmann says:

====================
The series contains two fixes in BPF core and test cases. For details
please see individual patches. Thanks!
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-10-31 16:53:18 -07:00
Daniel Borkmann
832c6f2c29 bpf: test make sure to run unpriv test cases in test_verifier
Right now unprivileged tests are never executed as a BPF test run,
only loaded. Allow for running them as well so that we can check
the outcome and probe for regressions.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-10-31 16:53:17 -07:00