I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a24006ed12 ('ptp: Enable clock
drivers along with associated net/PHY drivers') I wrongly made
PTP_1588_CLOCK_PCH depend on PCH_GBE. The dependency is really the
other way around. Therefore make PCH_GBE select PTP_1588_CLOCK_PCH
and remove the 'default y' from the latter.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:
- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
as part of net driver modules. (This also fixes cases where the PTP
subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
drivers but are built separately
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware clock drivers that select PTP_1588_CLOCK must currently
also select PPS. For those drivers that don't, the user must enable
PPS, then enable PTP_1588_CLOCK, then the driver. Simplify things for
developers and users by putting this selection in one place.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are now established subsystems, and we want drivers to be able
to select PPS and PTP_1588_CLOCK without depending on EXPERIMENTAL.
Further, the use of EXPERIMENTAL is now deprecated in general.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to allocate rx buffers pool by any reason, we'll just return
with an error, however we've previously successfully requested an irq. Fix
this by releasing the irq before returning the error.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.
This patch fixes it by the following steps:
1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.
After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we were in RX_FIFO_ERR state and entered pch_gbe_napi_poll(), we'll
anyway clean some rx space and thus can continue to receive more packets.
Currently, we re-set the RX_FIFO_ERR in situations when we've exhausted our
budget for RX cleaning or cleaned some TX packets. Removing it gives us
+20%-40% speed increase and a lot less of RX_FIFO_ERRors reported.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MAC_RX-related bits into separate functions.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang reported a kernel build failure as following:
drivers/built-in.o: In function `pch_gbe_ioctl':
pch_gbe_main.c:(.text+0x510370): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x510393): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x5103b3): undefined reference to `pch_ch_control_write'
...
It's a regression by commit da1586461. The root cause is that
the CONFIG_PPS is not set there, consequently CONFIG_PTP_1588_CLOCK
can not be set anyway, which finally causes ptp_pch and pch_gbe_main
build failures.
As David prefers to use *select* to fix such module co-dependency issues,
this patch explicitly selects all the possible dependencies of PCH_PTP.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Haicheng Li <haicheng.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The config combination:
CONFIG_PCH_GBE=y
CONFIG_PCH_PTP=y
CONFIG_PTP_1588_CLOCK=m
doesn't work, because then you have a built-in kernel
object (the PCH_PTP code) referring to symbols in a
module (PTP_1588_CLOCK).
Fix this like IXGBE, by using "select PTP_1588_CLOCK"
instead of a "depends on".
Reported-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_xmit_frame skb->len verification was incorrect in vlan case
causing bogus transfer length errors. One correction could be:
offset = skb->protocol == htons(ETH_P_8021Q) ? 0 : 4;
if (unlikely(skb->len > (adapter->hw.mac.max_frame_size - offset)))
However, this verification is not necessary, so remove it.
Signed-off-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds extra cleaning to the pch_gbe_clean_tx routine to avoid
transmit timeouts on some BCM PHYs that have different timing.
Also update the DRV_VERSION to 1.01, and show it.
Signed-off-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An extended ping test with 6 vlans resulted in a driver oops with a
netdev transmit timeout.
Fix WATCHDOG_TIMEOUT to be more like e1000e at 5 * HZ, to avoid
unnecessary transmit timeouts.
Signed-off-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to disable ethernet autonegation via ethtool,
the pch_gpe driver will set software reset bit of PHY chip, But
control register of PHY chip of FRI2 will reenable ethernet autonegation.
Signed-off-by: Wei Yang <w90p710@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy reported pch_gbe triggered "NETDEV WATCHDOG" errors.
May 11 11:06:09 kontron kernel: WARNING: at net/sched/sch_generic.c:261
dev_watchdog+0x1ec/0x200() (Not tainted)
May 11 11:06:09 kontron kernel: Hardware name: N/A
May 11 11:06:09 kontron kernel: NETDEV WATCHDOG: eth0 (pch_gbe):
transmit queue 0 timed out
It seems pch_gbe has a racy tx path (races with TX completion path)
Remove tx_queue_lock lock since it has no purpose, we must use tx_lock
instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Cress <andy.cress@us.kontron.com>
Tested-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.
The commit eefc48b ("pch_gbe: reprogram multicast address register on
reset") tried to fix this problem, but it introduces unnecessary
codes. In fact, all multicast addresses have been saved in netdev->mc,
So we can call pch_gbe_set_multi() directly after reset_hw and
reset_rx.
This commit kills 50+ line codes
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If I understand correct, NETIF_F_IP_CSUM only means the hardware
will compute the TCP/UDP checksum, IP checksum is always computed
in software
So as a workround of hardware unable to compute small packages
checksum, do not need to compute IP header checksum.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCH_GBE_ETH_ALEN is equal to ETH_ALEN, so we can replace it with
ETH_ALEN.
If they are not equal, it must be a bug, since this is ethernet,
and the address has been already stored to mc_addr_list as ETH_ALEN
bytes when call pch_gbe_mac_mc_addr_list_update.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time stamping code in this driver appears to have been copied from
the ixp4xx_eth.c driver, including this timing comment. I had actually
measured the time stamp delay on an IXP425, but I really doubt that this
value also applies here.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes code which needlessly ran the BPF twice per
packet. Instead, we just run the classifier once and test
whether the packet is any kind of PTP event message.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the driver so that multicast PTP event messages can
be recognized by the hardware time stamping unit. The station address
register must be set according to the desired transport type.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clears up a few coding style issues:
- Makes two function definitions a bit nicer looking.
- Remove unneeded parentheses.
- Simplify macros for register bits.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in phc_gbe_main will need to call this method in order to set the
station address register according to the receive time stamping filter.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes logic surrounding the test of the
transmit time stamping flag more readable.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the helper functions that give the transmit and
receive time stamps to return nanoseconds, instead of arbitrary clock
ticks.
[ RC - Rebased Takahiro's changes and wrote a commit message
explaining the changes. ]
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports EG20T ptp clock in the driver
Changes e-mail address.
Adds number.
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_validate_option() modifies 32 bits of memory but we pass
&hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc
which only has 8 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MAC is invalid or not implemented, do not abort the probe. Issue
a warning and prevent bringing the interface up until a MAC is set manually
(via ifconfig $IFACE hw ether $MAC).
Tested on two platforms, one with a valid MAC, the other without a MAC. The real
MAC is used if present, the interface fails to come up until the MAC is set on
the other. They successfully get an IP over DHCP and pass a simple ping and
login over ssh test.
This is meant to allow the Inforce SYS940X development board:
http://www.inforcecomputing.com/SYS940X_ECX.html
(and others suffering from a missing MAC) to work with the mainline kernel.
Without this patch, the probe will fail and the interface will not be created,
preventing the user from configuring the MAC manually.
This does not make any attempt to address a missing or invalid MAC for the
pch_phub driver.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
CC: Alan Cox <alan@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jon Mason <jdmason@kudzu.us>
CC: netdev@vger.kernel.org
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first #include must be pch_gbe.h as it
does a #define of pr_fmt.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev is unused in pch_gbe_setup_rctl. Remove this declaration to
avoid a compiler warning.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
