It seems that there's a bug at au0828 hardware/firmware
related to alternate setting: when the device is already at
alt 5, a further call causes the URBs to receive -ESHUTDOWN.
I found two different encarnations of this issue:
1) at qv4l2, it fails the second time we try to open the
video screen;
2) at xawtv, when audio underrun occurs, with is very
frequent, at least on my test machine.
The fix is simple: just check if alt=5 before calling
set_usb_interface().
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several issues on the current code:
1) msleep(1) is actually equivalent to msleep(10);
2) au8522_video_set() will set reg 0xa4 to the
proper value for SIF, CVBS or S-Video. No need
to force it to CVBS;
3) Let's not hardcode 0x9d for CBS on audio_set.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
setup_decoder_defaults() doesn't really care about the input
port. All it needs to know is if the input port is s-video or
not.
As the caller function already knows that, just pass a boolean
instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's set the the audio routing also at stream start. With this change,
we don't risk enabling the analog demux while not streaming, reducing
the risk of interfering with a DVB demux that might be happening.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same demod is used on both analog and digital mode. We should
not let the commands for analog mode to happen while the device
is in digital mode. So, monitor it via streamon.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The input mode is used not only inside the setup_decoder_defaults()
but also at au8522_*_mode routines.
So, move it one level up. As an advantage, we can now group the
function that sets the input into just one.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The analog part of au0828 is missing the tuner Kconfig dependency.
That makes the device to not work while in analog mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the basic GPLv2+ license notice to the copyright headers at the top
of all the source files in the img-ir driver.
Reported-by: David Härdeman <david@hardeman.nu>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sh_mobile_ceu_camera and sh_mobile_csi2 drivers are only useful on
SuperH and shmobile unless build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch change MACH_MX27 dependency to SOC_IMX27 for MX2 camera
driver, since MACH_MX27 symbol is scheduled for removal.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That driver hasn't been really maintained for a long time. It doesn't
compile in any way, it includes non-existent headers, has no users,
and marked as "BROKEN" more than year. Due to these factors, mx1_camera
is now removed from the tree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The R-Car Video Input driver is only useful on shmobile unless build
testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The platform data is a single word, so simply copy
it into the device's private data structure than
keeping a copy of the pointer.
This will make changing to device-tree binding
easier as it is one allocation instead of two.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
devm_kzalloc() allocations are freed when the device is unbound. But if a
certain path fails and the allocated memory cannot be used anyway it is
better to free it explicitly immediately. This patch does exactly this if
asynchronous group probing in scan_async_group() fails after memory has
been allocated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Calibrate the signal strength to dB.
For this callibration, I used adapter 0 (antenna 1), connected
via a normal cable to a DTF-2111 generator.
The same cabling and RF generator connected to adapter 1
(antenna 2) has a difference of +3dBm (signal was stronger
there).
Yet, changing the RF for a difference of, let's say, 6dB
reflected on a 6dB difference at the measured signal, with
is good.
So, the signal strengh can indeed be used to measure the
antenna gain, if the antenna is repositioned. It is
not precise to measure the absolute dBm value, however.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds DVBv5 stats support. For now, just mimic whatever dib8000
does, as they're very similar, with regards to statistics.
However, dib7000p_get_time_us() likely require some
adjustments, as I didn't actually reviewed the formula
for it to work with DVB-T. Still, better than nothing,
as latter patches can improve it.
This patch also doesn't show the signal strength in dB
yet. The code is already there, but it requires to be
callibrated.
A latter patch will do the calibration.
It seems that this patch is also a bug fix: Before this
patch, the frontend were not tuning with some userspace
tools. I suspect that dib7000p firmware or hardware
internally expects that the statistics to be collected,
in order for it to work. With this patch, the DVB core
will always retrive statistics, even if userspace doesn't
request. So, it makes the device work on all tested apps.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
The bug happens when:
CONFIG_DVB_DIB8000=m
CONFIG_DVB_USB_DIB0700=y
As a bonus, dib8000 won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with both Pixelview PV-D231 and MyGica S870.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function,
but, on dib8000, there are several exported symbols.
We need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename this function, in order to prepare for
a next patch that will add a new attach() function that
will be the only one exported by this module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dvb_attach() was unbalanced, as there was no dvb_dettach. Ok,
on current cases, the dettach is done by dvbdev, but that are some
future corner cases where we may need to do this before registering
the frontend.
So, add a dvb_detach() and use it at dvb_frontend.c.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change handling of signal_lock on rs2000. Use ibuf[2] to detect
lock as there is a longer wait for lock to appear in ibuf[6].
Remove last_key and key_timeout and use jiffies plus 60ms
to detect that streaming is still active.
If the current jiffies is time_after the interrupt urb overdue and
clear signal lock.
This results in far faster recovery of lock and streaming.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace resource handling in the driver with managed device resource.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C address of the sensor device was in the middle of the sub-device
name and not in the end as it should have been. The smiapp sub-device names
will change from e.g. "vs6555 1-0010 pixel array" to "vs6555 pixel array
1-0010".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove bogus 'numbuffers' and 'bufsize' module options. The number of buffers and
buffer sizes are determined by VIDIOC_REQBUFS and VIDIOC_S_FMT and the amount of
available memory (in the case of the MMAP stream I/O mode) and not by module
options.
These module params are a left-over from the original montavista code that used
these parameters to pre-allocate the memory needed for the buffers. The code that
allocated those buffers was never upstreamed since by the time the drivers were
added to the kernel the TI cmem module could be used in combination with the
USERPTR mode to reserve and pass physically contiguous memory pointers around.
These days of course CMA is used instead of cmem.
This patch removes these module options altogether since they no longer do what
they originally were designed for. They should never have been part of the
upstreamed code in the first place, so they've been pointless ever since
2.6.32 when this driver first appeared in the mainline kernel.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The field is assigned but never read, remove it.
This fixes a bug caused by the struct vb2_buffer field not being be the
very first field of the vsp1_video_buffer buffer structure as required
by videobuf2.
Cc: stable@vger.kernel.org
Reported-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTnmhkAAoJEHm+PkMAQRiGYyoIAJ+dCxQjx0Jmu5VLs48yvUkx
AVbnJeEq0ScgFPBAlfrGnnXczOyZGD+wveNRwb3bN4f6hGkWHPncfExAeTU35QQ+
92kCLScPU6kn4tnTqjac4ZrUhBCfgg5hFFamXOPidVDG4f5wYwql3IvP4O3eMOcZ
IOx7kgweqoPm4A/LjXQ3L21kghs88NXySWMwwfWFdXaV++ey07slCWLzGF5rMDh/
xfBDfgTS4gdrbGeE+1z/qkoWyHwKnCad8Uh2Fu5CcprElwCjLLhrLPccYSRKO2IR
2ZSj/mcMb1FhH7AOyXBYMVbjhOH5MCIlHvJYYp7kwHfs66UTmnkczOJxq1ynKP0=
=Whty
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc1' into patchwork
Linux 3.16-rc1
* tag 'v3.16-rc1': (11443 commits)
Linux 3.16-rc1
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
fix __swap_writepage() compile failure on old gcc versions
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
x86/vdso: Fix vdso_install
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
btrfs: fix error handling in create_pending_snapshot
btrfs: fix use of uninit "ret" in end_extent_writepage()
btrfs: free ulist in qgroup_shared_accounting() error path
Btrfs: fix qgroups sanity test crash or hang
btrfs: prevent RCU warning when dereferencing radix tree slot
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
btrfs: new ioctl TREE_SEARCH_V2
...
Pull networking fixes from David Miller:
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
3.16. They are simply fixes and code refactoring for the OMAP clock
drivers. The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=9/Iv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
Commit 3fd091e73b ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|
and
SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
Fixes related to some recent checksum modifications.
- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead517
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a couple of drivers (hpsa and lpfc) that got left out for further
testing in linux-next. We also have one fix to a prior submission (qla2xxx
sparse).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTm48MAAoJEDeqqVYsXL0M1YEH/iZyEILT4EIZxre/tspqX/LB
dxtGlmlF8AEU8/Eze3k/OB5nSuGcnYZ1hN1CgT2zZEv+sih6FekQOQV06qTwzwbo
DnWA3dOrPVgMzzSVvXFEjryroIUNhZvMy8TGu+DefE9b6FUs6B3VZlMR3A+TcSgV
cgknkG2Q6mWN8rO44pTSVlVDe2JpkvCYsHnqhO8uneQXVHNtsPpV7FfoLMLjBUDX
dgsaDiUjyrj0sdR1yOgRjDH68FPewEiEONdtKi63kkI6zWDFASiKDY9yc1eIyjVd
/1gbBJxwTRl4dWEdsigr/pOBxs6yjXGBSl/6PPDtuvdpWLFWUg4C2XtDLz0KLfU=
=tdDT
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a couple of drivers (hpsa and lpfc) that got left out for
further testing in linux-next. We also have one fix to a prior
submission (qla2xxx sparse)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
lpfc: Update lpfc version to driver version 10.2.8001.0
lpfc: Fix ExpressLane priority setup
lpfc: mark old devices as obsolete
lpfc: Fix for initializing RRQ bitmap
lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
lpfc: Update lpfc version to driver version 10.2.8000.0
lpfc: Update Copyright on changed files from 8.3.45 patches
lpfc: Update Copyright on changed files
lpfc: Fixed locking for scsi task management commands
lpfc: Convert runtime references to old xlane cfg param to fof cfg param
lpfc: Fix FW dump using sysfs
lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
lpfc: Fixed kernel panic in lpfc_abort_handler
lpfc: Fix locking for postbufq when freeing
lpfc: Fix locking for lpfc_hba_down_post
lpfc: Fix dynamic transitions of FirstBurst from on to off
hpsa: fix handling of hpsa_volume_offline return value
hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
hpsa: remove messages about volume status VPD inquiry page not supported
...
Pull more btrfs updates from Chris Mason:
"This has a few fixes since our last pull and a new ioctl for doing
btree searches from userland. It's very similar to the existing
ioctl, but lets us return larger items back down to the app"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix error handling in create_pending_snapshot
btrfs: fix use of uninit "ret" in end_extent_writepage()
btrfs: free ulist in qgroup_shared_accounting() error path
Btrfs: fix qgroups sanity test crash or hang
btrfs: prevent RCU warning when dereferencing radix tree slot
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
btrfs: new ioctl TREE_SEARCH_V2
btrfs: tree_search, search_ioctl: direct copy to userspace
btrfs: new function read_extent_buffer_to_user
btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
btrfs: tree_search, search_ioctl: accept varying buffer
btrfs: tree_search: eliminate redundant nr_items check
Pull aio fix and cleanups from Ben LaHaise:
"This consists of a couple of code cleanups plus a minor bug fix"
* git://git.kvack.org/~bcrl/aio-next:
aio: cleanup: flatten kill_ioctx()
aio: report error from io_destroy() when threads race in io_destroy()
fs/aio.c: Remove ctx parameter in kiocb_cancel
Tetsuo Handa wrote:
"Commit 62a8067a7f ("bio_vec-backed iov_iter") introduced an unnamed
union inside a struct which gcc-4.4.7 cannot handle. Name the unnamed
union as u in order to fix build failure"
Let's do this instead: there is only one place in the entire tree that
steps into this breakage. Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h
What doesn't work is handling their initializers:
struct {
int a;
union {
int b;
char c;
};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.
Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e. x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace. Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of . and -> instead of doing the right thing.
The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Tighten Dependency between ssi-protocol and omap-ssi
to fix build failures with randconfig.
* Use normal module refcounting in omap driver to fix
build with disabled module support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJTm50dAAoJENju1/PIO/qaI54P/ix0jMNYUJTHgEuPa8uifJY8
ZJBvE1jdb9k4keOaQvD5d0B0ExEBzfaBKzmSIGOlfREPcR2o7m20psLNXkkfsSbj
6jquDEp7ObOGgGdQ+3OebXRE+4qZm91H5AmX+8VMPbcxhcjLYvfn73T6dCbl/Wo/
y0VY2gGdUGQ0uQLcQ8WIeVah0mlmQ2lVbpVakG9cfDE+0yVYzb86xvepBvqzeMei
0xGmJo/dXQegLpS//uqSW6S9ds6BFPBvptLJjjQ1wOGdcBxe6ADkcu9VYZFv0FaN
XnD10FaKnRZROYTAC+9w7XksT4WsAwuuGRySrn2H12Da5XCxjTrGMCUnNgKc4HhO
cERQDdgtBe8+8wPD7kTnhYSzWWqQTBelwucmTuO1jecIa3vC6DA8UuMPKLE7K8Qs
g7MelhcT7aw3Clmgbvg11oH7YAfFnis9/fJ3Bq2wgKivfbEik++BjE1P8lVB2uVK
UXrLsEgSwEDQV3wLW4bpHO1NO8XtVFmkoBoxCWRKOYouhVlkucyt8HYi1pPwnhcq
hjxtXN7pUgf7lnFeeS7CH5xbZSkIkBHjUS3mmTPr5AKgsqYpNlyP8jMt7GTTZGXX
LzOS0VDAi73vl08k1yiLRDAhu7iZwKMk8+arTP3iYhzmk7OI/9gMB+pRf+zPGp6B
ADWLvkEREuu1zw6Ob4wp
=BKDp
-----END PGP SIGNATURE-----
Merge tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI build fixes from Sebastian Reichel:
- tighten dependency between ssi-protocol and omap-ssi to fix build
failures with randconfig.
- use normal module refcounting in omap driver to fix build with
disabled module support
* tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
hsi: omap_ssi_port: use normal module refcounting
HSI: fix omap ssi driver dependency
it blocks the OMAP boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6SvI
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"A first GPIO fix for the v3.16 series, this was serious since it
blocks the OMAP boot.
Sending you this vital fix before leaving for a short vacation so it
does not sit collecting dust in my tree for no good reason.
Apart from this, our v3.16 cycle looks like a good start"
* tag 'gpio-v3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: of: Fix handling for deferred probe for -gpio suffix
Pull x86 vdso fixes from Peter Anvin:
"Fixes for x86/vdso.
One is a simple build fix for bigendian hosts, one is to make "make
vdso_install" work again, and the rest is about working around a bug
in Google's Go language -- two are documentation patches that improves
the sample code that the Go coders took, modified, and broke; the
other two implements a workaround that keeps existing Go binaries from
segfaulting at least"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix vdso_install
x86/vdso: Hack to keep 64-bit Go programs working
x86/vdso: Add PUT_LE to store little-endian values
x86/vdso/doc: Make vDSO examples more portable
x86/vdso/doc: Rename vdso_test.c to vdso_standalone_test_x86.c
x86, vdso: Remove one final use of htole16()
Convert ltc4151 and vexpress drivers to use devm functions
Drop generic chip detection from lm85 driver
Avoid forward declarations in atxp1 driver
Fix sign extensions in ina2xx driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mv/m
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Sensirion SHTC1 humidity / temperature sensor
- convert ltc4151 and vexpress drivers to use devm functions
- drop generic chip detection from lm85 driver
- avoid forward declarations in atxp1 driver
- fix sign extensions in ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: vexpress: Use devm helper for hwmon device registration
hwmon: (atxp1) Avoid forward declaration
hwmon: add support for Sensirion SHTC1 sensor
hwmon: (ltc4151) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Drop generic detection
hwmon: (ina2xx) Cast to s16 on shunt and current regs
