This change allows to get driver specific debug messages output
providing a module parameter. As far as the maximum level of verbosity
is too high, it is demoted by default.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.120.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds external loopback support to tg3's ethtool selftest.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_test_loopback() function is starting to get more complicated as
more loopback tests are added. This patch cleans up the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pulls out the internal phy loopback setup code into a
separate function. This cleans up the loopback test code and makes it
available for NETIF_F_LOOPBACK support later.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver puts the device into MAC loopback in two places in the
driver. This patch consolidates the code into a single routine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that CPMU devices don't do MAC loopback, all the CPMU power saving
mode adjustments are unneeded. This patch removes the dead code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to further cleanup the transmit path by streamlining
some of the VLAN and FCOE/DCB tasks in the transmit path. In addition it
adds code for support software VLANs in the event that they are used in
conjunction with DCB and/or FCOE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CONFIG_FCOE is not the correct define to check since it is possible for it
to be CONFIG_FCOE_MODULE, as such the reference to it should be replaced
with IXGBE_FCOE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements a partial refactor of the TX map/queue and cleanup
routines. It merges the map and queue functionality and as a result
improves the transmit performance by avoiding unnecessary reads from memory.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the error message in the last DDP user buffer to warn_once
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some features currently not supported by the driver (e.g. RSS) require the
use of extended descriptors, but the driver is setup to only use legacy
descriptors in all modes except for when jumbo frames are enabled on some
parts. Convert the driver to always use extended descriptors in order to
enable the forthcoming support of these other features.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are valid configurations where Max BW is configured to zero for
some VNs.
Print the message only if debugging is enabled and do not call the
configuration "illegal".
[v2: use DP(), not BNX2X_DBG_ERR(); recommended by Eilon Greenstein.]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9aa3283595 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*
The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors). In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.
We do not explicitly select the Kconfig dependencies, as this would force
EMAC on. Doing it in the defconfig allows more flexibility.
Tested on a canyondlands board.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Korina.c is a MIPS-specific SOC driver and <asm/segment> is empty on
MIPS since 2.1.7 ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hw does not support vlans, dont call nv_vlan_mode because it has no point.
I believe that this should fix issues on older non-vlan supportive
chips (like Ingo has).
Reported-ty: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If our CAN device's device tree node has a clock-frequency property,
then use that value for the can devices clock frequency. If not, fall
back to asking the platform/mach code for the clock frequency associated
with the flexcan device.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
On powerpc, the OpenFirmware devices are not matched without specifying
an of_match array. Introduce that array as that is used for matching
on the Freescale P1010 processor.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Make flexcan driver handle register reads in the appropriate endianess.
This was a basic search and replace and then define some inlines.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc does not have a mach-####/clock.h. When testing, I found neither
arm nor powerpc needed the mach/clock.h at all so I removed it.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.
Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
ndo_set_rx_mode but do not support uc filtering
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from use of ndo_change_rx_flags in handling change of promisc
and allmulti. No need to store previous state locally.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's undesired to filter untagged packets at any time. So simply remove this.
Reported-by: Stephan Bärwolf <stephan.baerwolf@tu-ilmenau.de>
Tested-by: Stephan Bärwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eduard Sinelnikov (eduard.sinelnikov@gmail.com) found that if we change
bonding mode from active backup to round robin, some slaves are still keeping
"backup", and won't transmit packets.
As Jay Vosburgh(fubar@us.ibm.com) pointed out that we can work around that by
removing the bond_is_active_slave() check, because the "backup" flag is only
meaningful for active backup mode.
But if we just simply ignore the bond_is_active_slave() check,
the transmission will work fine, but we can't maintain the correct value of
"backup" flag for each slaves, though it is meaningless for other mode than
active backup.
I'd like to reset "backup" and "inactive" flag in bond_open,
thus we can keep the correct value of them.
As for bond_is_active_slave(), I'd like to prepare another patch to handle it.
V2:
Use C style comment.
Move read_lock(&bond->curr_slave_lock).
Replace restore with reset, for active backup mode, it means "restore",
but for other modes, it means "reset".
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pr_fmt(fmt) KBUILD_MODNAME ": " to prefix messages with "bnx2x: ".
Remove #define DP_LEVEL and use pr_notice.
Repeating KERN_<LEVEL> isn't necessary in multi-line printks.
printk macro neatening, use fmt and ##__VA_ARGS__.
Coalesce long formats.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uses of pr_cont should be avoided where reasonably possible
because they can be interleaved by other threads and processes.
Coalesce pr_cont uses.
Fix typos, duplicated words and spacing in DP uses caused
by split multi-line formats. Coalesce some of these
split formats. Add missing terminating newlines to DP uses.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pM and mac address directly instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sungem_phy is used by multiple, unrelated, drivers make it
build as a real module under drivers/net.
depmod will pick up the symbol dependency and make sure sungem_phy.ko
gets loaded any time sungem.ko or spider_net.ko is loaded.
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warning by adding the missing
__iomem annotation.
drivers/net/can/mscan/mscan.c:73:32: warning: incorrect type in argument 1 (different address spaces)
drivers/net/can/mscan/mscan.c:73:32: expected unsigned char volatile [noderef] [usertype] <asn:2>*addr
drivers/net/can/mscan/mscan.c:73:32: got unsigned char *<noident>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes build failures of the spider_net driver because it tries
to use a convoluted path to include this header.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/gianfar_ethtool.c:765: warning: the frame size of 2048 bytes is larger than 1024 bytes
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com>
Reviewed-and-tested-by: Sebastian Pöhn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some buggy chips, "vlan tag present" flag is set which causes packet
loss. Fix this by checking if rx vlan accel is enabled in features.
Reported-by: Michael Guntsche <mguntsche@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By a6b7a40786, remove interrupt.h
from netdevice.h. But this forget to revise sh_eth.
This fix the build failure.
error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_eth_interrupt'
error: implicit declaration of function 'request_irq'
error: 'sh_eth_interrupt' undeclared (first use in this function)
error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1386: error: for each function it appears in.)
error: 'IRQF_SHARED' undeclared (first use in this function)
error: implicit declaration of function 'free_irq'
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this code, the failure_cleanup label calls the function
plx_pci_del_card, which frees everything in the card->net_dev array. dev
is placed in this array immediately after allocation, so the two subsequent
jumps to failure_cleanup should not also call free_sja1000dev, but the
second one does.
If plx_pci_check_sja1000 fails, then free_sja1000dev is also called on
dev. Because dev is already in the card->net_dev array, this implies that
when plx_pci_del_card is later called, it may get freed again. So that
entry is reset to NULL after the free.
Finally, if there is a problem with one channel, there will be a hole in the
array. card->channels counts the number of channels that have succeeded,
and does not keep track of the index of the largest element in the array
that is valid. So the loop in plx_pci_del_card is changed to go up to
PLX_PCI_MAX_CHAN, which is only 2.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver still has a few places where stack variables are
passed to the cdc_ncm_do_request function. This triggers a stack trace in
lib/dma-debug.c if the CONFIG_DEBUG_DMA_API option is set.
Adjust these calls to pass parameters that have been allocated with
kzalloc.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath6kl is now in drivers/net/wireless/ath so the staging driver
is not supported anymore and should be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the Manageability Engine (ME) is enabled on 82579, it periodically
accesses some MAC CSR registers. There is an arbiter in hardware which
prevents simultaneous access of these registers by the host software, i.e.
the driver. There is a hardware bug in the aribter that signals a host
access of the registers later than it actually happens. A write of the
Transmit or Receive Descriptor Tail register could result in an incorrect
value if the driver and ME perform simultaneous accesses which could result
in an access to an invalid memory address. This would return an
Unsupported Request which could hang the hardware. Workaround the issue by
checking the FWSM register bit24 which is set by ME before it accesses the
MAC CSR registers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC can drop short packets when the PHY detects noise on the line at
100Mbps due to a timing issue. Workaround the issue by increasing the PLL
counter so the PHY properly recognizes the synchronization pattern from the
MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82577/8/9 in half-duplex when a received packet is passed from the PHY
to the MAC, if too many preamble octects are stripped from the packet
before arriving at the MAC, it can be misintrepeted as an in-band message
rather than an actual frame. For example, if the frame contents resembled
an interrupt request in-band message, it would trigger a false interrupt.
In most cases, the packet is just dropped.
By reducing the number of preamble octets stripped from the beginning of
the frame when passing it from the PHY to the MAC, the MAC will interpret
the frame properly.
An additional uses of the magic PHY_REG(770, 16) have been updated with a
define introduced with this patch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to fix a memory leak found via code review for FCOE.
Specifically on DDP flows the SKBs were being dropped without being
recycled, freed, or given to the stack.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the HiperSockets device driver to send and receive
af_iucv traffic over HiperSockets transport.
TX: Driver uses new asynchronous delivery of storage blocks to pass
flow control/congestion information from the HiperSockets microcode
to the af_iucv socket.
RX: Memory for incoming traffic is preallocated and passed to
HiperSockets layer. If receiver is not capable to clean its buffers
shared with HiperSockets and pass new memory to the HiperSockets
layer this will cause flow control/congestion events on the
sender.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exploits the QDIO support for asynchronous delivery of storage
blocks for Hipersockets. The exploitation is not configured per default and
may be enabled via the function qeth_configure_cq.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that signal adapter commands are issued if they are
indicated to be required.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that signal adapter commands are issued if they are
indicated to be required.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces support for asynchronous delivery of storage blocks for
Hipersockets. Upper layers may exploit this functionality to reuse SBALs for
which the delivery status is still pending.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA cards can be configured to support 1 or 4 output queues. This
does not apply to HiperSockets. This patch limits determination of
the configured number of output queues to OSA cards only, but excludes
HiperSockets.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In layer 3 mode IPv6 over VLAN does not work on newer OSA levels in
case the sender and receiver run on the same (shared) OSA adapter.
Keep vlan info in the skb so the qdio header is filled with the
required vlan tag.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the move of the Ethernet drivers into drivers/net/ethernet/
there was some leftover cleanup to do in the Kconfig and Makefile.
Removed the 10/100, 1000, and 10GbE Kconfig menus.
Removed the out-dated pci-skeleton.c file which was used an
example driver. With the current networking features and
structure, the file is no longer a good example to use for
driver creation.
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on feedback from Alan Cox, the acenic driver moved to
drivers/net/ethernet/alteon/ and made the necessary Kconfig and
Makefile changes.
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Tilera driver into drivers/net/ethernet/tile and
make the necessary Kconfig and Makefile changes.
Updated the Kconfig so that the options defualt to y if TILE kernel.
CC: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Xircom driver into drivers/net/ethernet/xircom/ and
make the necessary Kconfig and Makefile changes.
CC: <psheer@icon.co.za>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Renesas driver into drivers/net/ethernet/renesas/ and make
the necessary Kconfig and Makefile changes.
CC: Yoshihiro Shimoda <yoshihiro.shirmoda.uh@renesas.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the netx driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the Davicom driver into drivers/net/ethernet/davicom/ and
make the necessary Kconfig and Makefile changes.
CC: Ben Dooks <ben@simtec.co.uk>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the Microchip driver into drivers/net/ethernet/microchip/ and
make the necessary Kconfig and Makefile changes.
CC: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Aeroflex Gaisler driver into drivers/net/ethernet/aeroflex/
and make the necessary Kconfig and Makefile changes.
CC: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Avionic driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Dave Ethernet driver into drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.
CC: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the HP driver into drivers/net/ethernet/hp/ and
made the necessary Kconfig and Makefile changes.
CC: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Serial: Add PID(0xF7C0) to FTDI SIO driver for a zeitcontrol-device
USB: Serial: Add device ID for Sierra Wireless MC8305
USB: Serial: Added device ID for Qualcomm Modem in Sagemcom's HiLo3G
usb/host/pci-quirks.c: correct annotation of `ehci_dmi_nohandoff_table'
USB: option driver: add PID for Vodafone-Huawei K4511
USB: option driver: add PID for Vodafone-Huawei K4510
USB: option driver: add PID for Vodafone-Huawei K3771
USB: option driver: add PID for Vodafone-Huawei K3770
usb: serial: ftdi_sio.c: For the FT232H FTDI_SIO_SET_BAUDRATE_REQUEST, index needs to be shifted too
usb/isp1760: Added missing call to usb_hcd_check_unlink_urb() during unlink
USB: EHCI: Fix test mode sequence
USB: ftdi_sio: fix minor typo in get_ftdi_divisor
USB: at91_udc: include linux/prefetch.h explicitly
USB: usb-storage: unusual_devs entry for ARM V2M motherboard.
usb/ehci-mxc: add missing inclusion of mach/hardware.h
USB: assign instead of equal in usbtmc.c
usb: renesas_usbhs: fixup usbhsg_for_each_uep 1st pos
usb: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: gadget: net2272 - Correct includes
usb: musb: fix oops on musb_gadget_pullup
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
zcache: Fix build error when sysfs is not defined
zcache: Use div_u64 for 64-bit division
staging:rts_pstor: fix thread synchronization flow
drivers:staging:solo6x10:add the missed slab.h
staging: zcache: include module.h for MODULE_LICENSE
drivers/staging/hv/blkvsc_drv.c: eliminate NULL pointer dereference
Staging: Add clk API note to nvec/TODO
drivers/staging/ath6kl/miscdrv/ar3kps/ar3kpsparser.c: adjust array index
staging: more missing slab.h inclusions
drivers/staging/solo6x10/p2m.c needs slab.h
drivers/staging/solo6x10/core.c needs slab.h
drivers/staging/dt3155v4l/dt3155v4l.c needs slab.h
drivers/staging/speakup/devsynth.c: fix "buffer size is not provably correct" error
Staging: iio: add some unlocks to raw_read() functions
staging: ft1000_proc needs asm/io.h for inw/outw on sparc
staging: rtl8192u: declare MODULE_FIRMWARE
gma500: Fix clashes with DRM updates
staging: zcache: module is GPL
staging: fix zcache building
Move the Adaptec driver into drivers/net/ethernet/adaptec/ and make
the necessary Kconfig and Makefile changes.
CC: Ion Badulescu <ionut@badula.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the nForce driver into drivers/net/ethernet/nvidia/ and make
the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Myson driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the RDC driver into drivers/net/ethernet/rdc/ and make the
necessary Kconfig and Makefile changes.
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Atmel driver into drivers/net/ethernet/cadence/ and
make the necessary Kconfig and Makefile changes.
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Move the Analog Devices Inc driver into drivers/net/ethernet/adi/ and
make the necessary Kconfig and Makefile changes.
CC: <uclinux-dist-devel@blackfin.uclinux.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Bob Liu <bob.liu@analog.com>
Move the Lantiq driver into drivers/net/ethernet/ and the
necessary Kconfig and Makefile changes.
CC: John Crispin <blogic@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: John Crispin <blogic@openwrt.org>
Move the MIPS drivers into drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IDT driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes
CC: "IDT Inc." <rischelp@idt.com>
CC: Felix Fietkau <nbd@openwrt.org>
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IC Plus driver into drivers/net/ethernet/icplus/ and
make the necessary Kconfig and Makefile changes.
CC: <craig_rich@sundanceti.com>
CC: <sorbica@icplus.com.tw>
CC: <jesse@icplus.com.tw>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of maintaining static scan table in driver, scan list is sent
to cfg80211 stack (after parsing each scan command response).
In assoc handler (for infra and ibss network) requested BSS information
is retrieved using cfg80211_get_bss() API.
With the changes above some redundant code are removed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver gets a tx status report for an A-MPDU sent to a station that
just went to sleep, that leaves a race condition where this tx status can
trigger another A-MPDU transmission.
To fix this, check if the station is sleeping before queueing the tid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_4k_get_eeprom() overrides the eeprom value for txgain if the
minor version is not 19 or above with a value of 0.
ar9002_hw_init_mode_gain_regs() relies on this information to
determine whether this is a high power wifi card or not. The override
caused the driver to always use the 'normal' power tables even for
high power devices if their minor version was not high enough. Thus
leading to reduced power output.
This isn't needed for the AR9285; the check originated with the
AR9280 setup code which requires the EEPROM version check.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
e1000e: increase driver version number
e1000e: alternate MAC address update
e1000e: do not disable receiver on 82574/82583
e1000e: alternate MAC address does not work on device id 0x1060
PCnet: Fix section mismatch
bnx2x: disable dcb on 578xx since not supported yet
bnx2x: properly clean indirect addresses
bnx2x: prevent race between undi_unload and load flows
bnx2x: fix select_queue when FCoE is disabled
bnx2x: init FCOE FP only once
ipv4: some rt_iif -> rt_route_iif conversions
net/bridge/netfilter/ebtables.c: use available error handling code
net/netlabel/netlabel_kapi.c: add missing cleanup code
net/irda: sh_sir: tidyup compile warning
net/irda: sh_sir: add missing header
net/irda: sh_irda: add missing header
slcan: ldisc generated skbs are received in softirq context
scm: Capture the full credentials of the scm sender
tcp: initialize variable ecn_ok in syncookies path
drivers/net/wireless/wl1251: add missing kfree
...
Move the Xilinx drivers into drivers/net/ethernet/xilinx/ and
make the necessary Kconfig and Makefile changes.
CC: John Williams <john.williams@petalogix.com>
CC: "David H. Lynch Jr." <dhlii@dlasys.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the JME driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Cavium driver to drivers/net/ethernet/octeon/ and
make the necessary Kconfig and Makefile changes.
CC: David Daney <david.daney@cavium.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: David Daney <david.daney@cavium.com>
Move the packet engine drivers to drivers/net/ethernet/packetengines/
and the necessary Kconfig and Makefile changes.
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the s6gmac driver to drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.
CC: Oskar Schirmer <os@emlix.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Tundra driver to drivers/net/ethernet/tundra/ and
make the necessary Kocnfig and Makefile changes.
CC: Kong Lai <kong.lai@tundra.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Nuvoton driver into drivers/net/ethernet/nuvoton/ and
make the necessary Kconfig and Makefile changes.
CC: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Cirrus Ethernet driver into drivers/net/ethernet/cirrus/
and make the necessary Kconfig and Makefile changes
CC: Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the SiS drivers into drivers/net/ethernet/sis/ and make the
necessary Kconfig and Makefile changes
CC: Daniele Venzano <venza@brownhat.org>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Error comes from commit ac124ff973
(be2net: cleanup and refactor stats code)
ERROR: "__udivdi3" [drivers/net/benet/be2net.ko] undefined!
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Toshiba ethernet drivers into drivers/net/ethernet/toshiba
and make the necessary Kconfig and Makefile changes.
CC: Geoff Levand <geoff@infradead.org>
CC: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Micrel drivers into drivers/net/ethernet/micrel/ and
make the necessary Kconfig and Makefile changes.
CC: Ben Dooks <ben@simtec.co.uk>
CC: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Allied Telesis/Fujitsu drivers into drivers/net/ethernet/fujitsu/
and make the necessary Kconfig and Makefile changes.
CC: Shingo Fujimoto <shingo@flab.fujitsu.co.jp>
CC: Yutaka Tamiya <tamy@flab.fujitsu.co.jp>
CC: Rene Schmit <rene@bss.lu>
CC: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>