Add support for ptp interrupt. This interrupt is used when using 2-step
timestamping. For each timestamp that is added in a queue, an interrupt
is generated.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend dt-bindings for sparx5 with ptp interrupt. This is generated
when doing 2-step timestamping and the timestamp can be read from the
FIFO.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ifh is not changed, it is fixed for each frame for each
port that is sent out. Move this on the stack because this ifh needs to
be change based on the frames that are send out. This is needed for PTP
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Ramadoss says:
====================
Add support for LAN937x T1 Phy Driver
LAN937x is a Multi-port 100Base-T1 Switch and it internally uses LAN87xx
T1 Phy. This series of patch update the initialization routine for the
LAN87xx phy and also add LAN937x part support. Added the T1 Phy
master-slave configuration through ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To configure the T1 phy as master or slave using the ethtool -s <dev>
master-slave <forced-master/forced-slave>, the config_aneg and read
status functions are added.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN937x T1 switch is based on LAN87xx Phy, so reusing the init script of
the LAN87xx. There is a workaround in accessing the DSP bank register
for LAN937x Phy. Whenever there is a bank switch to DSP registers, then
we need a one dummy read access before proceeding to the actual register
access.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new initialization sequence is the improvement to the existing init
routine. Init routine does soft reset, run init script and set
Hw_init. Added the new access_smi_poll_timeout() for polling smi
bank write.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed the empty lines in struct phy_drivers.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used the PHY_ID_MATCH_MODEL MACRO for describing the phy_id and
phy_id_mask.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced the current code of resetting of LAN87xx phy to
genphy_soft_reset library function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divya Koppera says:
====================
Add support for 1588 in LAN8814
The following patch series contains:
- Fix for concurrent register access, which provides
atomic access to extended page register reads/writes.
- Provides dt-bindings related to latency and timestamping
that are required for LAN8814 phy.
- 1588 hardware timestamping support in LAN8814 phy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 1588 in LAN8814 phy driver.
It supports 1-step and 2-step timestamping.
Co-developed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports configuring latency values and also adds
check for phy timestamping feature.
Signed-off-by: Divya Koppera<Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make Extended page register accessing atomic,
to overcome unexpected output from register
reads/writes.
Fixes: 7c2dcfa295 ("net: phy: micrel: Add support for LAN8804 PHY")
Signed-off-by: Divya Koppera<Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Menglong Dong says:
====================
net: dev: add skb drop reasons to net/core/dev.c
In the commit c504e5c2f9 ("net: skb: introduce kfree_skb_reason()"),
we added the support of reporting the reasons of skb drops to kfree_skb
tracepoint. And in this series patches, reasons for skb drops are added
to the link layer, which means that 'net/core/dev.c' is our target.
Following functions are processed:
sch_handle_egress()
__dev_xmit_skb()
enqueue_to_backlog()
do_xdp_generic()
sch_handle_ingress()
__netif_receive_skb_core()
and following new drop reasons are added (what they mean can be see in
the document of them):
SKB_DROP_REASON_QDISC_EGRESS
SKB_DROP_REASON_QDISC_DROP
SKB_DROP_REASON_CPU_BACKLOG
SKB_DROP_REASON_XDP
SKB_DROP_REASON_QDISC_INGRESS
SKB_DROP_REASON_PTYPE_ABSENT
In order to add skb drop reasons to kfree_skb_list(), the function
kfree_skb_list_reason() is introduced in the 2th patch, which will be
used in __dev_xmit_skb() in the 3th patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reason for skb drops to __netif_receive_skb_core() when packet_type
not found to handle the skb. For this purpose, the drop reason
SKB_DROP_REASON_PTYPE_ABSENT is introduced. Take ether packets for
example, this case mainly happens when L3 protocol is not supported.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() used in sch_handle_ingress() with
kfree_skb_reason(). Following drop reasons are introduced:
SKB_DROP_REASON_TC_INGRESS
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() used in do_xdp_generic() with kfree_skb_reason().
The drop reason SKB_DROP_REASON_XDP is introduced for this case.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() used in enqueue_to_backlog() with
kfree_skb_reason(). The skb rop reason SKB_DROP_REASON_CPU_BACKLOG is
introduced for the case of failing to enqueue the skb to the per CPU
backlog queue. The further reason can be backlog queue full or RPS
flow limition, and I think we needn't to make further distinctions.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reasons for skb drops to __dev_xmit_skb() by replacing
kfree_skb_list() with kfree_skb_list_reason(). The drop reason of
SKB_DROP_REASON_QDISC_DROP is introduced for qdisc enqueue fails.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To report reasons of skb drops, introduce the function
kfree_skb_list_reason() and make kfree_skb_list() an inline call to
it. This function will be used in the next commit in
__dev_xmit_skb().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() used in sch_handle_egress() with kfree_skb_reason().
The drop reason SKB_DROP_REASON_TC_EGRESS is introduced. Considering
the code path of tc egerss, we make it distinct with the drop reason
of SKB_DROP_REASON_QDISC_DROP in the next commit.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Andrzej Siewior says:
====================
net: Convert user to netif_rx().
This is the first batch of converting netif_rx_ni() caller to
netif_rx(). The change making this possible is net-next and
netif_rx_ni() is a wrapper around netif_rx(). This is a clean up in
order to remove netif_rx_ni().
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: bridge@lists.linux-foundation.org
Cc: Chris Zankel <chris@zankel.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: linux-doc@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: Łukasz Stelmach <l.stelmach@samsung.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Łukasz Stelmach <l.stelmach@samsung.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: Mike Travis <mike.travis@hpe.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-03-03
Jacob Keller says:
This series refactors the ice networking driver VF storage from a simple
static array to a hash table. It also introduces krefs and proper locking
and protection to prevent common use-after-free and concurrency issues.
There are two motivations for this work. First is to make the ice driver
more resilient by preventing a whole class of use-after-free bugs that can
occur around concurrent access to VF structures while removing VFs.
The second is to prepare the ice driver for future virtualization work to
support Scalable IOV, an alternative VF implementation compared to Single
Root IOV. The new VF implementation will allow for more dynamic VF creation
and removal, necessitating a more robust implementation for VF storage that
can't rely on the existing mechanisms to prevent concurrent access
violations.
The first few patches are cleanup and preparatory work needed to make the
conversion to the hash table safe. Following this preparatory work is a
patch to migrate the VF structures and variables to a new sub-structure for
code clarity. Next introduce new interface functions to abstract the VF
storage. Finally, the driver is actually converted to the hash table and
kref implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Cleanups for ocelot/felix drivers
This patch set is an assorted collection of minor cleanups brought to
the felix DSA driver and ocelot switch library.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an apparently incorrect conflict resolution on my part in commit
54c3198460 ("net: mscc: ocelot: enforce FDB isolation when
VLAN-unaware"), "ocelot->ports[port]->is_dsa_8021q_cpu = false" was
supposed to be replaced by "ocelot_port_unset_dsa_8021q_cpu(ocelot, port)"
which does the same thing, and more. But now we have both, so the direct
assignment is redundant. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet extraction failures over register-based MMIO are silent, and
difficult to pinpoint. Add an error message to remedy this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automated tools complain that felix_check_xtr_pkt() has logic to drain
the CPU queue on the reception of a PTP packet over Ethernet, yet it
returns an uninitialized error code in the case where the CPU queue was
empty.
This is not likely to happen (/possible if hardware works correctly),
but it isn't a fatal condition either. The PTP packet will be dequeued
from the CPU queue when the next PTP packet arrives. So initialize "err"
to 0 for the case where nothing was dequeued during this iteration.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA ->port_rxtstamp() function is never called for PTP_CLASS_NONE:
dsa_skb_defer_rx_timestamp:
if (type == PTP_CLASS_NONE)
return false;
if (likely(ds->ops->port_rxtstamp))
return ds->ops->port_rxtstamp(ds, p->dp->index, skb, type);
So practically, the argument is unused, so remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This assignment is redundant, since ocelot->npi has already been set to
-1 by felix_npi_port_deinit(). Call path:
felix_change_tag_protocol
-> felix_del_tag_protocol(DSA_TAG_PROTO_OCELOT)
-> felix_teardown_tag_npi
-> felix_npi_port_deinit
-> felix_set_tag_protocol(DSA_TAG_PROTO_OCELOT_8021Q)
-> felix_setup_tag_8021q
-> felix_8021q_cpu_port_init
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardcoding these IP protocol numbers in is2_entry_set() obscures the
purpose of the code, so replace the magic numbers with the definitions
from linux/in.h.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify ocelot_vcap_block_remove_filter by using list_for_each_entry
instead of list_for_each.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen reported the following warning messages from smc-sysctl.rst
Documentation/networking/smc-sysctl.rst:3: WARNING: Title overline
too short.
Documentation/networking/smc-sysctl.rst: WARNING: document isn't
included in any toctree
Fix the title overline and add smc-sysctl entry into
Documentation/networking/index.rst
Fixes: 12bbb0d163 ("net/smc: add sysctl for autocorking")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220303113527.62047-1-dust.li@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice driver stores VF structures in a simple array which is allocated
once at the time of VF creation. The VF structures are then accessed
from the array by their VF ID. The ID must be between 0 and the number
of allocated VFs.
Multiple threads can access this table:
* .ndo operations such as .ndo_get_vf_cfg or .ndo_set_vf_trust
* interrupts, such as due to messages from the VF using the virtchnl
communication
* processing such as device reset
* commands to add or remove VFs
The current implementation does not keep track of when all threads are
done operating on a VF and can potentially result in use-after-free
issues caused by one thread accessing a VF structure after it has been
released when removing VFs. Some of these are prevented with various
state flags and checks.
In addition, this structure is quite static and does not support a
planned future where virtualization can be more dynamic. As we begin to
look at supporting Scalable IOV with the ice driver (as opposed to just
supporting Single Root IOV), this structure is not sufficient.
In the future, VFs will be able to be added and removed individually and
dynamically.
To allow for this, and to better protect against a whole class of
use-after-free bugs, replace the VF storage with a combination of a hash
table and krefs to reference track all of the accesses to VFs through
the hash table.
A hash table still allows efficient look up of the VF given its ID, but
also allows adding and removing VFs. It does not require contiguous VF
IDs.
The use of krefs allows the cleanup of the VF memory to be delayed until
after all threads have released their reference (by calling ice_put_vf).
To prevent corruption of the hash table, a combination of RCU and the
mutex table_lock are used. Addition and removal from the hash table use
the RCU-aware hash macros. This allows simple read-only look ups that
iterate to locate a single VF can be fast using RCU. Accesses which
modify the hash table, or which can't take RCU because they sleep, will
hold the mutex lock.
By using this design, we have a stronger guarantee that the VF structure
can't be released until after all threads are finished operating on it.
We also pave the way for the more dynamic Scalable IOV implementation in
the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
bluetooth, and netfilter.
Current release - regressions:
- iwlwifi: don't advertise TWT support, prevent FW crash
- xfrm: fix the if_id check in changelink
- xen/netfront: destroy queues before real_num_tx_queues is zeroed
- bluetooth: fix not checking MGMT cmd pending queue, make scanning
work again
Current release - new code bugs:
- mptcp: make SIOCOUTQ accurate for fallback socket
- bluetooth: access skb->len after null check
- bluetooth: hci_sync: fix not using conn_timeout
- smc: fix cleanup when register ULP fails
- dsa: restore error path of dsa_tree_change_tag_proto
- iwlwifi: fix build error for IWLMEI
- iwlwifi: mvm: propagate error from request_ownership to the user
Previous releases - regressions:
- xfrm: fix pMTU regression when reported pMTU is too small
- xfrm: fix TCP MSS calculation when pMTU is close to 1280
- bluetooth: fix bt_skb_sendmmsg not allocating partial chunks
- ipv6: ensure we call ipv6_mc_down() at most once, prevent leaks
- ipv6: prevent leaks in igmp6 when input queues get full
- fix up skbs delta_truesize in UDP GRO frag_list
- eth: e1000e: fix possible HW unit hang after an s0ix exit
- eth: e1000e: correct NVM checksum verification flow
- ptp: ocp: fix large time adjustments
Previous releases - always broken:
- tcp: make tcp_read_sock() more robust in presence of urgent data
- xfrm: distinguishing SAs and SPs by if_id in xfrm_migrate
- xfrm: fix xfrm_migrate issues when address family changes
- dcb: flush lingering app table entries for unregistered devices
- smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error
- mac80211: fix EAPoL rekey fail in 802.3 rx path
- mac80211: fix forwarded mesh frames AC & queue selection
- netfilter: nf_queue: fix socket access races and bugs
- batman-adv: fix ToCToU iflink problems and check the result
belongs to the expected net namespace
- can: gs_usb, etas_es58x: fix opened_channel_cnt's accounting
- can: rcar_canfd: register the CAN device when fully ready
- eth: igb, igc: phy: drop premature return leaking HW semaphore
- eth: ixgbe: xsk: change !netif_carrier_ok() handling in
ixgbe_xmit_zc(), prevent live lock when link goes down
- eth: stmmac: only enable DMA interrupts when ready
- eth: sparx5: move vlan checks before any changes are made
- eth: iavf: fix races around init, removal, resets and vlan ops
- ibmvnic: more reset flow fixes
Misc:
- eth: fix return value of __setup handlers
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=TqqZ
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from can, xfrm, wifi, bluetooth, and netfilter.
Lots of various size fixes, the length of the tag speaks for itself.
Most of the 5.17-relevant stuff comes from xfrm, wifi and bt trees
which had been lagging as you pointed out previously. But there's also
a larger than we'd like portion of fixes for bugs from previous
releases.
Three more fixes still under discussion, including and xfrm revert for
uAPI error.
Current release - regressions:
- iwlwifi: don't advertise TWT support, prevent FW crash
- xfrm: fix the if_id check in changelink
- xen/netfront: destroy queues before real_num_tx_queues is zeroed
- bluetooth: fix not checking MGMT cmd pending queue, make scanning
work again
Current release - new code bugs:
- mptcp: make SIOCOUTQ accurate for fallback socket
- bluetooth: access skb->len after null check
- bluetooth: hci_sync: fix not using conn_timeout
- smc: fix cleanup when register ULP fails
- dsa: restore error path of dsa_tree_change_tag_proto
- iwlwifi: fix build error for IWLMEI
- iwlwifi: mvm: propagate error from request_ownership to the user
Previous releases - regressions:
- xfrm: fix pMTU regression when reported pMTU is too small
- xfrm: fix TCP MSS calculation when pMTU is close to 1280
- bluetooth: fix bt_skb_sendmmsg not allocating partial chunks
- ipv6: ensure we call ipv6_mc_down() at most once, prevent leaks
- ipv6: prevent leaks in igmp6 when input queues get full
- fix up skbs delta_truesize in UDP GRO frag_list
- eth: e1000e: fix possible HW unit hang after an s0ix exit
- eth: e1000e: correct NVM checksum verification flow
- ptp: ocp: fix large time adjustments
Previous releases - always broken:
- tcp: make tcp_read_sock() more robust in presence of urgent data
- xfrm: distinguishing SAs and SPs by if_id in xfrm_migrate
- xfrm: fix xfrm_migrate issues when address family changes
- dcb: flush lingering app table entries for unregistered devices
- smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error
- mac80211: fix EAPoL rekey fail in 802.3 rx path
- mac80211: fix forwarded mesh frames AC & queue selection
- netfilter: nf_queue: fix socket access races and bugs
- batman-adv: fix ToCToU iflink problems and check the result belongs
to the expected net namespace
- can: gs_usb, etas_es58x: fix opened_channel_cnt's accounting
- can: rcar_canfd: register the CAN device when fully ready
- eth: igb, igc: phy: drop premature return leaking HW semaphore
- eth: ixgbe: xsk: change !netif_carrier_ok() handling in
ixgbe_xmit_zc(), prevent live lock when link goes down
- eth: stmmac: only enable DMA interrupts when ready
- eth: sparx5: move vlan checks before any changes are made
- eth: iavf: fix races around init, removal, resets and vlan ops
- ibmvnic: more reset flow fixes
Misc:
- eth: fix return value of __setup handlers"
* tag 'net-5.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
ipv6: fix skb drops in igmp6_event_query() and igmp6_event_report()
net: dsa: make dsa_tree_change_tag_proto actually unwind the tag proto change
ixgbe: xsk: change !netif_carrier_ok() handling in ixgbe_xmit_zc()
selftests: mlxsw: resource_scale: Fix return value
selftests: mlxsw: tc_police_scale: Make test more robust
net: dcb: disable softirqs in dcbnl_flush_dev()
bnx2: Fix an error message
sfc: extend the locking on mcdi->seqno
net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error cause by server
net/smc: fix unexpected SMC_CLC_DECL_ERR_REGRMB error generated by client
net: arcnet: com20020: Fix null-ptr-deref in com20020pci_probe()
tcp: make tcp_read_sock() more robust
bpf, sockmap: Do not ignore orig_len parameter
net: ipa: add an interconnect dependency
net: fix up skbs delta_truesize in UDP GRO frag_list
iwlwifi: mvm: return value for request_ownership
nl80211: Update bss channel on channel switch for P2P_CLIENT
iwlwifi: fix build error for IWLMEI
ptp: ocp: Add ptp_ocp_adjtime_coarse for large adjustments
batman-adv: Don't expect inter-netns unique iflink indices
...
Before we switch the VF data structure storage mechanism to a hash,
introduce new accessor functions to define the new interface.
* ice_get_vf_by_id is a function used to obtain a reference to a VF from
the table based on its VF ID
* ice_has_vfs is used to quickly check if any VFs are configured
* ice_get_num_vfs is used to get an exact count of how many VFs are
configured
We can drop the old ice_validate_vf_id function, since every caller was
just going to immediately access the VF table to get a reference
anyways. This way we simply use the single ice_get_vf_by_id to both
validate the VF ID is within range and that there exists a VF with that
ID.
This change enables us to more easily convert the codebase to the hash
table since most callers now properly use the interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We maintain a number of values for VFs within the ice_pf structure. This
includes the VF table, the number of allocated VFs, the maximum number
of supported SR-IOV VFs, the number of queue pairs per VF, the number of
MSI-X vectors per VF, and a bitmap of the VFs with detected MDD events.
We're about to add a few more variables to this list. Clean this up
first by extracting these members out into a new ice_vfs structure
defined in ice_virtchnl_pf.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----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=yVdT
-----END PGP SIGNATURE-----
Merge tag 'auxdisplay-for-linus-v5.17-rc7' of git://github.com/ojeda/linux
Pull auxdisplay fixes from Miguel Ojeda:
"A few lcd2s fixes from Andy Shevchenko"
* tag 'auxdisplay-for-linus-v5.17-rc7' of git://github.com/ojeda/linux:
auxdisplay: lcd2s: Use proper API to free the instance of charlcd object
auxdisplay: lcd2s: Fix memory leak in ->remove()
auxdisplay: lcd2s: Fix lcd2s_redefine_char() feature
