Allow coda_seq_end_work to be called multiple times, move the setting
of ctx->initialized from coda_start/stop_streaming() into
coda_start_encoding/decoding and coda_seq_end_work, respectively,
and skip the SEQ_END command in coda_seq_end_work if the context is
already deinitialized before.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In stream end mode the hardware will read the bitstream to its end,
overshooting the write pointer. Do not write additional data into
the bitstream in this mode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All decoder instances using the BIT processor should preload buffers
into the bitstream ring buffer, including MPEG4 decoding. Fix this
by explicitly stating the above condition instead of listing all
relevant input formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mvcol buffer is allocated at the end of the first internal buffer.
This patch fixes an out of bounds array access.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is already done for one side of the comparison with the expectation
that the HW counter rolls over at the 16 bit boundary. This is true when
decoding a h.264 stream, but doesn't hold for at least MJPEG. As we don't
know the exact wrap-around point for this format just clamp the HW counter
to the same 16 bits. This should be enough to detect most of the errors
and saves us from doing different comparisons based on the decoded format.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1_entity_is_streaming() function is called in atomic context when
queuing buffers, and sleeps due to a mutex. As the mutex just protects
access to one structure field, fix this by replace the mutex with a
spinlock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The checks need to be performed on up to two planes, as the third plane,
if present, must have the same stride and size as the second plane.
The code incorrectly performs the checks on at least two planes instead
of at most two planes, fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should set "ret" on this error path instead of returning success.
Fixes: df3305156f ('[media] v4l: xilinx: Add Xilinx Video IP core')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver is tested on our hardware and all the implemented features
works as expected.
Missing features:
- CEC support
- HDCP repeater support
- IR support
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
[hans.verkuil@cisco.com: updated copyright year to 2015]
[hans.verkuil@cisco.com: update confusing confctl_mutex comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
bdisp_dev->dbg.copy_node shall be a copy of (and not point to)
bdisp_ctx->node, since this resource is freed upon driver release.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the composing (at VIDEO_CAPTURE) with the _selection API.
v4l2-compliance successfully run ("test Composing: OK")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commit implements frame decimation for stk1160, which allows
to support format changes instead of a static frame size.
The stk1160 supports independent row and column decimation, in two
different modes:
* set a number of rows/columns units to skip for each unit sent.
* set a number of rows/columns units to send for each unit skipped.
This effectively allows to achieve different frame scaling ratios.
The unit number can be set to either two row/columns sent/skipped,
or four row/columns sent/skipped. Since the video format (UYVY)
has 4-bytes, using a unit number of two row/columns results
in frame color 'shifting', so set to four row/columns sent/skipped.
Signed-off-by: Michael Stegemann <michael@stegemann.it>
Signed-off-by: Dale Hamel <dale.hamel@srvthe.net>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These messages are not really informational, and just makes the driver's
output too verbose. This commit changes some messages to a debug level,
removes a really useless "driver loaded" message and finally undefines
the DEBUG macro.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Upon a S_FMT the input/requested frame size and pixel format is
overwritten by the current sub-device settings.
Fix this so application can actually set the frame size and format.
Fixes: 417d2e507e ("[media] media: platform: add VPFE capture driver support for AM437X")
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of VIDEO_ADV7604 and VIDEO_COBALT (the latter
selects the former) on GPIOLIB if COMPILE_TEST is enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix small typo (missing 'it') in the documentation for
V4L2_CTRL_FLAG_EXECUTE_ON_WRITE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The documentation had two media_version entries. The second one was a typo and
it should be driver_version instead. Correct this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a new helper function called v4l2_subdev_notify_event() which will
deliver the specified event to both the v4l2 subdev event queue as well as
to the notify callback. The former is typically used by userspace
applications to listen to notification events while the later is used by
bridge drivers. Combining both into the same function avoids boilerplate
code in subdev drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow userspace applications to subscribe to control change events. This
can e.g. be used to monitor the 5V detect control to be notified when a
source is connected or disconnected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow userspace applications to subscribe to control change events. This
can e.g. be used to monitor the 5V detect control to be notified when a
source is connected or disconnected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the vdev pointer == NULL, then just return.
This makes it easier for subdev drivers to use this function without having to
check if the sd->devnode pointer is NULL or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVouXcAAoJEHm+PkMAQRiGjWQIAJcfwb9z5U8jCR+FyvqqM//U
gzKdODPpwuJBa4IpQoCIZlT4wbGH3W0euuVKWk2zv9f+D/i5D/ZIAj0Wt5mjs1Z2
/uhEMnYskGHn7Q3HCQyyjPqTi6I4DnSiFS880xTQhsufXxtpDmVWETO1fyCvlt73
NU6Y0Y/Oe+tN5/Qp3wKLUaZMigiiBD5GviGQQNHtJ6UIorOCJnw5mYSx0dWPotIL
SYUno4WIR/48FKABUDxs13YK7JDLv3w4h8FimvY+cY6hKLZ9zUhFUCCE3OKXcpHQ
auAKhyi9YcqJxWvVUCl1gV8NmBefETp6zfWf07NBaDnFiNsfW+mqfO0mWwnOT5s=
=C7m8
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc2' into patchwork
Linux 4.2-rc2
We need to backport changeset 31f0245545, with fixes a bug at
include/linux/compiler.h that breaks sparse.
* tag 'v4.2-rc2': (221 commits)
Linux 4.2-rc2
Revert "drm/i915: Use crtc_state->active in primary check_plane func"
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
tick/broadcast: Prevent NULL pointer dereference
selinux: fix mprotect PROT_EXEC regression caused by mm change
parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
stifb: Implement hardware accelerated copyarea
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
arm64: entry32: remove pointless register assignment
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
...
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit dec4f799d0.
Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:
crtc_state = state->base.state ?
intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;
So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.
There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull VFS fixes from Al Viro:
"Fixes for this cycle regression in overlayfs and a couple of
long-standing (== all the way back to 2.6.12, at least) bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
Pull MIPS fixes from Ralf Baechle:
"A fair number of 4.2 fixes also because Markos opened the flood gates.
- Patch up the math used calculate the location for the page bitmap.
- The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
around was causing issues on non-Malta platforms, so move the code
to a Malta specific location.
- A spelling fix replicated through several files.
- Fix to the emulation of an R2 instruction for R6 cores.
- Fix the JR emulation for R6.
- Further patching of mindless 64 bit issues.
- Ensure the kernel won't crash on CPUs with L2 caches with >= 8
ways.
- Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.
- Fix cache flushing for multithreaded cores.
- A build fix"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
MIPS: c-r4k: Fix cache flushing for MT cores
Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
MIPS: cps-vec: Use macros for various arithmetics and memory operations
MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
MIPS: Fix erroneous JR emulation for MIPS R6
MIPS: Fix branch emulation for BLTC and BGEC instructions
MIPS: kernel: traps: Fix broken indentation
MIPS: bootmem: Don't use memory holes for page bitmap
MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
MIPS, CPUFREQ: Fix spelling of Institute.
MIPS: Lemote 2F: Fix build caused by recent mass rename.
Pull x86 fixes from Thomas Gleixner:
- the high latency PIT detection fix, which slipped through the cracks
for rc1
- a regression fix for the early printk mechanism
- the x86 part to plug irq/vector related hotplug races
- move the allocation of the espfix pages on cpu hotplug to non atomic
context. The current code triggers a might_sleep() warning.
- a series of KASAN fixes addressing boot crashes and usability
- a trivial typo fix for Kconfig help text
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
x86/irq: Retrieve irq data after locking irq_desc
x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
x86/irq: Plug irq vector hotplug race
x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
x86/espfix: Init espfix on the boot CPU side
x86/espfix: Add 'cpu' parameter to init_espfix_ap()
x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
x86/kasan: Add message about KASAN being initialized
x86/kasan: Fix boot crash on AMD processors
x86/kasan: Flush TLBs after switching CR3
x86/kasan: Fix KASAN shadow region page tables
x86/init: Clear 'init_level4_pgt' earlier
x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()
Pull timer fixes from Thomas Gleixner:
"This update from the timer departement contains:
- A series of patches which address a shortcoming in the tick
broadcast code.
If the broadcast device is not available or an hrtimer emulated
broadcast device, some of the original assumptions lead to boot
failures. I rather plugged all of the corner cases instead of only
addressing the issue reported, so the change got a little larger.
Has been extensivly tested on x86 and arm.
- Get rid of the last holdouts using do_posix_clock_monotonic_gettime()
- A regression fix for the imx clocksource driver
- An update to the new state callbacks mechanism for clockevents.
This is required to simplify the conversion, which will take place
in 4.3"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Prevent NULL pointer dereference
time: Get rid of do_posix_clock_monotonic_gettime
cris: Replace do_posix_clock_monotonic_gettime()
tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
tick/broadcast: Handle spurious interrupts gracefully
tick/broadcast: Check for hrtimer broadcast active early
tick/broadcast: Return busy when IPI is pending
tick/broadcast: Return busy if periodic mode and hrtimer broadcast
tick/broadcast: Move the check for periodic mode inside state handling
tick/broadcast: Prevent deep idle if no broadcast device available
tick/broadcast: Make idle check independent from mode and config
tick/broadcast: Sanity check the shutdown of the local clock_event
tick/broadcast: Prevent hrtimer recursion
clockevents: Allow set-state callbacks to be optional
clocksource/imx: Define clocksource for mx27
Pull irq fix from Thomas Gleixner:
"A single fix for a cpu hotplug race vs. interrupt descriptors:
Prevent irq setup/teardown across the cpu starting/dying parts of cpu
hotplug so that the starting/dying cpu has a stable view of the
descriptor space. This has been an issue for all architectures in the
cpu dying phase, where interrupts are migrated away from the dying
cpu. In the starting phase its mostly a x86 issue vs the vector space
update"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hotplug: Prevent alloc/free of irq descriptors during cpu up/down
Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course). However, there's one case where that
does *not* happen. Namely, if you open it by fhandle with cold dcache,
then unlink() and close().
In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal. In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()). The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in. As the result, we have the final iput() delayed
indefinitely. It's trivial to reproduce -
void flush_dcache(void)
{
system("mount -o remount,rw /");
}
static char buf[20 * 1024 * 1024];
main()
{
int fd;
union {
struct file_handle f;
char buf[MAX_HANDLE_SZ];
} x;
int m;
x.f.handle_bytes = sizeof(x);
chdir("/root");
mkdir("foo", 0700);
fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
close(fd);
name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
flush_dcache();
fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
unlink("foo/bar");
write(fd, buf, sizeof(buf));
system("df ."); /* 20Mb eaten */
close(fd);
system("df ."); /* should've freed those 20Mb */
flush_dcache();
system("df ."); /* should be the same as #2 */
}
will spit out something like
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 283282 21692 93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).
Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull libnvdimm fixes from Dan Williams:
"1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
bug fixes (patches 1-6)
2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).
Granted these are slightly large for a -rc update. They have been
out for review in one form or another since the end of May and were
deferred from the merge window while we settled on the "PMEM API"
for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
and wmb_pmem).
Now that those apis are merged we implement them in the BLK driver
to guarantee that mmio aperture moves stay ordered with respect to
incoming read/write requests, and that writes are flushed through
those mmio-windows and platform-buffers to be persistent on media.
These pass the sub-system unit tests with the updates to
tools/testing/nvdimm, and have received a successful build-report from
the kbuild robot (468 configs).
With acks from Rafael for the touches to drivers/acpi/"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
nfit: fix smatch "use after null check" report
nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
libnvdimm: smatch cleanups in __nd_ioctl
sparse: fix misplaced __pmem definition
Pull i2c fixes from Wolfram Sang:
"Mostly slight adjusments for new drivers, but also one core fix for
which finally the dependencies are now available as well"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Mark instantiated device nodes with OF_POPULATE
i2c: jz4780: Fix return value if probe fails
i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
i2c: I2C_MT65XX should depend on HAS_DMA
Pull input fixes from Dmitry Torokhov:
"A fix (revert) for a recent regression in Synaptics driver and a fix
for Elan i2c touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
Input: elan_i2c - change the hover event from MT to ST
that we added this rc and a handful of driver fixes that came in
during the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vTi8
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A small set of fixes for problems found by smatch in new drivers that
we added this rc and a handful of driver fixes that came in during the
merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Incorrect register offset used for lock_status
clk: mediatek: mt8173: Fix enabling of critical clocks
drivers: clk: st: Fix mux bit-setting for Cortex A9 clocks
drivers: clk: st: Add CLK_GET_RATE_NOCACHE flag to clocks
drivers: clk: st: Fix flexgen lock init
drivers: clk: st: Fix FSYN channel values
drivers: clk: st: Remove unused code
clk: qcom: Use parent rate when set rate to pixel RCG clock
clk: at91: do not leak resources
clk: stm32: Fix out-by-one error path in the index lookup
clk: iproc: fix bit manipulation arithmetic
clk: iproc: fix memory leak from clock name
Pull drm fixes from Dave Airlie:
"A bunch of fixes for radeon, intel, omap and one amdkfd fix.
Radeon fixes are all over, but it does fix some cursor corruption
across suspend/resume. i915 should fix the second warn you were
seeing, so let us know if not. omap is a bunch of small fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
drm/radeon: disable vce init on cayman (v2)
drm/amdgpu: fix timeout calculation
drm/radeon: check if BO_VA is set before adding it to the invalidation list
drm/radeon: allways add the VM clear duplicate
Revert "Revert "drm/radeon: dont switch vt on suspend""
drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
drm/radeon: Clean up reference counting and pinning of the cursor BOs
drm/amdkfd: validate pdd where it acquired first
Revert "drm/i915: Allocate context objects from stolen"
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/radeon: fix underflow in r600_cp_dispatch_texture()
drm/radeon: default to 2048 MB GART size on SI+
drm/radeon: fix HDP flushing
drm/radeon: use RCU query for GEM_BUSY syscall
drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
drm/radeon: Handle irqs only based on irq ring, not irq status regs.
drm/i915: Use crtc_state->active in primary check_plane func
drm/i915: Check crtc->active in intel_crtc_disable_planes
drm/i915: Restore all GGTT VMAs on resume
...
Pull selinux fixes from James Morris.
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix mprotect PROT_EXEC regression caused by mm change
selinux: don't waste ebitmap space when importing NetLabel categories
Pull btrfs fixes from Chris Mason:
"This is an assortment of fixes. Most of the commits are from Filipe
(fsync, the inode allocation cache and a few others). Mark kicked in
a series fixing corners in the extent sharing ioctls, and everyone
else fixed up on assorted other problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong check for btrfs_force_chunk_alloc()
Btrfs: fix warning of bytes_may_use
Btrfs: fix hang when failing to submit bio of directIO
Btrfs: fix a comment in inode.c:evict_inode_truncate_pages()
Btrfs: fix memory corruption on failure to submit bio for direct IO
btrfs: don't update mtime/ctime on deduped inodes
btrfs: allow dedupe of same inode
btrfs: fix deadlock with extent-same and readpage
btrfs: pass unaligned length to btrfs_cmp_data()
Btrfs: fix fsync after truncate when no_holes feature is enabled
Btrfs: fix fsync xattr loss in the fast fsync path
Btrfs: fix fsync data loss after append write
Btrfs: fix crash on close_ctree() if cleaner starts new transaction
Btrfs: fix race between caching kthread and returning inode to inode cache
Btrfs: use kmem_cache_free when freeing entry in inode cache
Btrfs: fix race between balance and unused block group deletion
btrfs: add error handling for scrub_workers_get()
btrfs: cleanup noused initialization of dev in btrfs_end_bio()
btrfs: qgroup: allow user to clear the limitation on qgroup
A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
prima2 as well as a few arm64-specific DT fixes.
This series also includes a late to support a new Allwinner (sunxi)
SoC, but since it's rather simple and isolated to the
platform-specific code, it's included it for this -rc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UEUK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
prima2 as well as a few arm64-specific DT fixes.
This series also includes a late to support a new Allwinner (sunxi)
SoC, but since it's rather simple and isolated to the
platform-specific code, it's included it for this -rc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add device tree for ARM SMM-A53x2 on LogicTile Express 20MG
arm: dts: vexpress: add missing CCI PMU device node to TC2
arm: dts: vexpress: describe all PMUs in TC2 dts
GICv3: Add ITS entry to THUNDER dts
arm64: dts: Add poweroff button device node for APM X-Gene platform
ARM: dts: am4372.dtsi: disable rfbi
ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
ARM: dts: am4372: Add emif node
Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
ARM: sunxi: Enable simplefb in the defconfig
ARM: Remove deprecated symbol from defconfig files
ARM: sunxi: Add Machine support for A33
ARM: sunxi: Introduce Allwinner H3 support
Documentation: sunxi: Update Allwinner SoC documentation
ARM: prima2: move to use REGMAP APIs for rtciobrg
ARM: dts: atlas7: add pinctrl and gpio descriptions
ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
memory: omap-gpmc: Fix parsing of devices
Dan reported that the recent changes to the broadcast code introduced
a potential NULL dereference.
Add the proper check.
Fixes: e045431190 "tick/broadcast: Sanity check the shutdown of the local clock_event"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull parisc fixes from Helge Deller:
"We have one important patch from Dave Anglin and myself which fixes
PTE/TLB race conditions which caused random segmentation faults on our
debian buildd servers, and one patch from Alex Ivanov which speeds up
the graphical text console on the STI framebuffer driver"
* 'parisc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
stifb: Implement hardware accelerated copyarea
commit 66fc130394 ("mm: shmem_zero_setup
skip security check and lockdep conflict with XFS") caused a regression
for SELinux by disabling any SELinux checking of mprotect PROT_EXEC on
shared anonymous mappings. However, even before that regression, the
checking on such mprotect PROT_EXEC calls was inconsistent with the
checking on a mmap PROT_EXEC call for a shared anonymous mapping. On a
mmap, the security hook is passed a NULL file and knows it is dealing
with an anonymous mapping and therefore applies an execmem check and no
file checks. On a mprotect, the security hook is passed a vma with a
non-NULL vm_file (as this was set from the internally-created shmem
file during mmap) and therefore applies the file-based execute check
and no execmem check. Since the aforementioned commit now marks the
shmem zero inode with the S_PRIVATE flag, the file checks are disabled
and we have no checking at all on mprotect PROT_EXEC. Add a test to
the mprotect hook logic for such private inodes, and apply an execmem
check in that case. This makes the mmap and mprotect checking
consistent for shared anonymous mappings, as well as for /dev/zero and
ashmem.
Cc: <stable@vger.kernel.org> # 4.1.x
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>
The increased use of pdtlb/pitlb instructions seemed to increase the
frequency of random segmentation faults building packages. Further, we
had a number of cases where TLB inserts would repeatedly fail and all
forward progress would stop. The Haskell ghc package caused a lot of
trouble in this area. The final indication of a race in pte handling was
this syslog entry on sibaris (C8000):
swap_free: Unused swap offset entry 00000004
BUG: Bad page map in process mysqld pte:00000100 pmd:019bbec5
addr:00000000ec464000 vm_flags:00100073 anon_vma:0000000221023828 mapping: (null) index:ec464
CPU: 1 PID: 9176 Comm: mysqld Not tainted 4.0.0-2-parisc64-smp #1 Debian 4.0.5-1
Backtrace:
[<0000000040173eb0>] show_stack+0x20/0x38
[<0000000040444424>] dump_stack+0x9c/0x110
[<00000000402a0d38>] print_bad_pte+0x1a8/0x278
[<00000000402a28b8>] unmap_single_vma+0x3d8/0x770
[<00000000402a4090>] zap_page_range+0xf0/0x198
[<00000000402ba2a4>] SyS_madvise+0x404/0x8c0
Note that the pte value is 0 except for the accessed bit 0x100. This bit
shouldn't be set without the present bit.
It should be noted that the madvise system call is probably a trigger for many
of the random segmentation faults.
In looking at the kernel code, I found the following problems:
1) The pte_clear define didn't take TLB lock when clearing a pte.
2) We didn't test pte present bit inside lock in exception support.
3) The pte and tlb locks needed to merged in order to ensure consistency
between page table and TLB. This also has the effect of serializing TLB
broadcasts on SMP systems.
The attached change implements the above and a few other tweaks to try
to improve performance. Based on the timing code, TLB purges are very
slow (e.g., ~ 209 cycles per page on rp3440). Thus, I think it
beneficial to test the split_tlb variable to avoid duplicate purges.
Probably, all PA 2.0 machines have combined TLBs.
I dropped using __flush_tlb_range in flush_tlb_mm as I realized all
applications and most threads have a stack size that is too large to
make this useful. I added some comments to this effect.
Since implementing 1 through 3, I haven't had any random segmentation
faults on mx3210 (rp3440) in about one week of building code and running
as a Debian buildd.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Helge Deller <deller@gmx.de>
