Support the V1.1 hardware revisions with the following change:
Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in
order to be able to run UHS SD cards in ultra high speed 1.8V mode.
[ 207.502011] mmc2: host does not support reading read-only switch,
assuming write-enable
[ 207.517011] mmc2: new ultra high speed SDR104 SDHC card at address
aaaa
[ 207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB
[ 207.545096] mmcblk2: p1
root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios
clock: 208000000 Hz
actual clock: 204000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 6 (sd uhs SDR104)
signal voltage: 1 (1.80 V)
driver type: 0 (driver type B)
root@apalis-t30:~# hdparm -t /dev/mmcblk2
/dev/mmcblk2:
Timing buffered disk reads: 256 MB in 3.02 seconds = 84.71 MB/sec
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the hda node from the carrier board to the module level device
tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename a few nodes using more common names:
- rename tps65911@2d to pmic@2d
- rename stmpe811@41 to touchscreen@41
- rename tps62362@60 to regulator@60
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename hdmiddc to hdmi_ddc to be more in-line with other device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Apalis Evaluation Board uses Apalis GPIO7 on MXM3 pin 15 as reset
signal for its PLX PEX 8605 PCIe Switch.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop obsolete spidev device tree nodes as nowadays one should do this
by binding the spidev driver to specific instances/chip selects at
runtime.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop model and compatible nodes from the module level device tree as
they get overridden by the carrier board device tree anyway.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLX Technology meanwhile got bought by Broadcom Corporation but the
vendor prefix plx is still used in 8 current device trees. This silences
the following checkpatch.pl warning:
WARNING: DT compatible string vendor "plx" appears un-documented
-- check ./Documentation/devicetree/bindings/vendor-prefixes.txt
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Get rid of the fake clocks simple bus and use node names as per the
actual schematics.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add i2c-thermtrip which would set the DEV_OFF bit in the DCDC control
register of the TPS65911 PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clean-up pinmuxing:
- white-space clean-up
- explicitly disable input of BKL1_ON, BKL1_PWM and BKL1_PWM_EN#
- annotate Apalis I2C3 usage for CAM
- get rid of nvidia,lock property
- add missing eMMC sdmmc4_cmd_pt7 and explicitly enable input
- explicitly disable lcd_dc1_pd2 (e.g. LM95245 I2C address pin)
- annotate TOUCH_PEN_INT# being on-module
- As underscores in node names are not recommended replace them all
where possible with dashes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop pwmleds in favour of using regular PWMs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart"
compatible definitions from the carrier board to the module level device
trees. One could still override this in a custom carrier board device
tree if required.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate PCIe port nodes and clean-up PCIe controller/port status' with
respect to carrier board vs. module level device trees. As port 3
connects to the on-module Gigabit Ethernet MACPHY it is always enabled
together with the PCIe controller itself.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to avoid any floating SD card detect pins as may e.g. happen on
Ixora V1.1A pull them all up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is similar to tegra124 and avoids the following being reported
upon boot:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There was a dot instead of a comma. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull timer update from Thomas Gleixner:
"New defines for the compat time* types so they can be shared between
32bit and 64bit builds. Not used yet, but merging them now allows the
actual conversions to be merged through different maintainer trees
without dependencies
We still have compat interfaces for 32bit on 64bit even with the new
2038 safe timespec/val variants because pointer size is different. And
for the old style timespec/val interfaces we need yet another 'compat'
interface for both 32bit native and 32bit on 64bit"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
y2038: Provide aliases for compat helpers
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
- Lift gcc test into Kconfig
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=8D/M
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugin fix from Kees Cook:
"Lift gcc test into Kconfig. This is for better behavior when the
kernel is built with Clang, reported by Stefan Agner"
* tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Disable when building under Clang
Pull perf updates from Thomas Gleixner:
"Kernel:
- Improve kallsyms coverage
- Add x86 entry trampolines to kcore
- Fix ARM SPE handling
- Correct PPC event post processing
Tools:
- Make the build system more robust
- Small fixes and enhancements all over the place
- Update kernel ABI header copies
- Preparatory work for converting libtraceevnt to a shared library
- License cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
tools arch x86: Update tools's copy of cpufeatures.h
perf python: Fix pyrf_evlist__read_on_cpu() interface
perf mmap: Store real cpu number in 'struct perf_mmap'
perf tools: Remove ext from struct kmod_path
perf tools: Add gzip_is_compressed function
perf tools: Add lzma_is_compressed function
perf tools: Add is_compressed callback to compressions array
perf tools: Move the temp file processing into decompress_kmodule
perf tools: Use compression id in decompress_kmodule()
perf tools: Store compression id into struct dso
perf tools: Add compression id into 'struct kmod_path'
perf tools: Make is_supported_compression() static
perf tools: Make decompress_to_file() function static
perf tools: Get rid of dso__needs_decompress() call in __open_dso()
perf tools: Get rid of dso__needs_decompress() call in symbol__disassemble()
perf tools: Get rid of dso__needs_decompress() call in read_object_code()
tools lib traceevent: Change to SPDX License format
perf llvm: Allow passing options to llc in addition to clang
perf parser: Improve error message for PMU address filters
...
Pull x86 fixes from Thomas Gleixner:
- Correct the L1TF fallout on 32bit and the off by one in the 'too much
RAM for protection' calculation.
- Add a helpful kernel message for the 'too much RAM' case
- Unbreak the VDSO in case that the compiler desides to use indirect
jumps/calls and emits retpolines which cannot be resolved because the
kernel uses its own thunks, which does not work for the VDSO. Make it
use the builtin thunks.
- Re-export start_thread() which was unexported when the 32/64bit
implementation was unified. start_thread() is required by modular
binfmt handlers.
- Trivial cleanups
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/l1tf: Suggest what to do on systems with too much RAM
x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM
x86/kvm/vmx: Remove duplicate l1d flush definitions
x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
x86/process: Re-export start_thread()
x86/mce: Add notifier_block forward declaration
x86/vdso: Fix vDSO build if a retpoline is emitted
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
Pull licking update from Thomas Gleixner:
"Mark the switch cases which fall through to the next case with the
proper comment so the fallthrough compiler checks can be enabled"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Mark expected switch fall-throughs
* memory_failure() gets confused by dev_pagemap backed mappings. The
recovery code has specific enabling for several possible page states
that needs new enabling to handle poison in dax mappings. Teach
memory_failure() about ZONE_DEVICE pages.
-----BEGIN PGP SIGNATURE-----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=Ftop
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm memory-failure update from Dave Jiang:
"As it stands, memory_failure() gets thoroughly confused by dev_pagemap
backed mappings. The recovery code has specific enabling for several
possible page states and needs new enabling to handle poison in dax
mappings.
In order to support reliable reverse mapping of user space addresses:
1/ Add new locking in the memory_failure() rmap path to prevent races
that would typically be handled by the page lock.
2/ Since dev_pagemap pages are hidden from the page allocator and the
"compound page" accounting machinery, add a mechanism to determine
the size of the mapping that encompasses a given poisoned pfn.
3/ Given pmem errors can be repaired, change the speculatively
accessed poison protection, mce_unmap_kpfn(), to be reversible and
otherwise allow ongoing access from the kernel.
A side effect of this enabling is that MADV_HWPOISON becomes usable
for dax mappings, however the primary motivation is to allow the
system to survive userspace consumption of hardware-poison via dax.
Specifically the current behavior is:
mce: Uncorrected hardware memory error in user-access at af34214200
{1}[Hardware Error]: It has been corrected by h/w and requires no further action
mce: [Hardware Error]: Machine check events logged
{1}[Hardware Error]: event severity: corrected
Memory failure: 0xaf34214: reserved kernel page still referenced by 1 users
[..]
Memory failure: 0xaf34214: recovery action for reserved kernel page: Failed
mce: Memory error not recovered
<reboot>
...and with these changes:
Injecting memory failure for pfn 0x20cb00 at process virtual address 0x7f763dd00000
Memory failure: 0x20cb00: Killing dax-pmd:5421 due to hardware memory corruption
Memory failure: 0x20cb00: recovery action for dax page: Recovered
Given all the cross dependencies I propose taking this through
nvdimm.git with acks from Naoya, x86/core, x86/RAS, and of course dax
folks"
* tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pmem: Restore page attributes when clearing errors
x86/memory_failure: Introduce {set, clear}_mce_nospec()
x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses
mm, memory_failure: Teach memory_failure() about dev_pagemap pages
filesystem-dax: Introduce dax_lock_mapping_entry()
mm, memory_failure: Collect mapping size in collect_procs()
mm, madvise_inject_error: Let memory_failure() optionally take a page reference
mm, dev_pagemap: Do not clear ->mapping on final put
mm, madvise_inject_error: Disable MADV_SOFT_OFFLINE for ZONE_DEVICE pages
filesystem-dax: Set page->index
device-dax: Set page->index
device-dax: Enable page_mapping()
device-dax: Convert to vmf_insert_mixed and vm_fault_t
Collection of misc libnvdimm patches for 4.19 submission
* Adding support to read locked nvdimm capacity.
* Change test code to make DSM failure code injection an override.
* Add support for calculate maximum contiguous area for namespace.
* Add support for queueing a short ARS when there is on going ARS for
nvdimm.
* Allow NULL to be passed in to ->direct_access() for kaddr and
pfn params.
* Improve smart injection support for nvdimm emulation testing.
* Fix test code that supports for emulating controller temperature.
* Fix hang on error before devm_memremap_pages()
* Fix a bug that causes user memory corruption when data returned
to user for ars_status.
* Maintainer updates for Ross Zwisler emails and adding Jan Kara to fsdax.
-----BEGIN PGP SIGNATURE-----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=5p2n
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.19_misc' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dave Jiang:
"Collection of misc libnvdimm patches for 4.19 submission:
- Adding support to read locked nvdimm capacity.
- Change test code to make DSM failure code injection an override.
- Add support for calculate maximum contiguous area for namespace.
- Add support for queueing a short ARS when there is on going ARS for
nvdimm.
- Allow NULL to be passed in to ->direct_access() for kaddr and pfn
params.
- Improve smart injection support for nvdimm emulation testing.
- Fix test code that supports for emulating controller temperature.
- Fix hang on error before devm_memremap_pages()
- Fix a bug that causes user memory corruption when data returned to
user for ars_status.
- Maintainer updates for Ross Zwisler emails and adding Jan Kara to
fsdax"
* tag 'libnvdimm-for-4.19_misc' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm: fix ars_status output length calculation
device-dax: avoid hang on error before devm_memremap_pages()
tools/testing/nvdimm: improve emulation of smart injection
filesystem-dax: Do not request kaddr and pfn when not required
md/dm-writecache: Don't request pointer dummy_addr when not required
dax/super: Do not request a pointer kaddr when not required
tools/testing/nvdimm: kaddr and pfn can be NULL to ->direct_access()
s390, dcssblk: kaddr and pfn can be NULL to ->direct_access()
libnvdimm, pmem: kaddr and pfn can be NULL to ->direct_access()
acpi/nfit: queue issuing of ars when an uc error notification comes in
libnvdimm: Export max available extent
libnvdimm: Use max contiguous area for namespace size
MAINTAINERS: Add Jan Kara for filesystem DAX
MAINTAINERS: update Ross Zwisler's email address
tools/testing/nvdimm: Fix support for emulating controller temperature
tools/testing/nvdimm: Make DSM failure code injection an override
acpi, nfit: Prefer _DSM over _LSR for namespace label reads
libnvdimm: Introduce locked DIMM capacity support
