Although the term "nuke" is part of the FBC spec, it's not very
intuitive, so let's rename it to make it easier for people that are
not familiar with the spec.
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446664257-32012-2-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The bspec indicates that DDI A using four lanes is the only valid
configuration for Broxton (Broxton doesn't have a DDI E to split these
lanes with); the DDI_A_4_LANES bit of port A's DDI_BUF_CTL should always
be set by the BIOS. However some BIOS versions seem to only be setting
this bit if eDP is actually lit up at boot time; if the BIOS doesn't
turn on the eDP panel because an external display is plugged in, then
this bit is never properly initialized. The end result of this is that
we wind up calculating a lower max data rate than we should and may wind
up rejecting the native mode for panels that we should be able to drive.
Let's workaround this BIOS bug by just turning the DDI_A_4_LANES bit on
in our driver's internal state if we recognize that we're running on BXT
where it should have been on anyway.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Tested-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446764012-27251-1-git-send-email-matthew.d.roper@intel.com
VMA offsets are 64 bits. Plane surface offsets are in ggtt and
the hardware register to set this is thus 32 bits. Be explicit
about these and convert carefully to from vma to final size.
This will make sparse happy by not creating 32bit pointers out
of 64bit vma offsets.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446204375-29831-1-git-send-email-mika.kuoppala@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We have had one case where buggy csr/dmc firmware version influenced
gt side and caused a hang. Add dmc firmware loading state and
version to error state.
v2: - Rebased on top of Damien's patches
- included fw load state
v3: include dmc info only if platform supports it (Chris)
v4: move *csr to branch scope (Chris)
v5: remove dependency to csr_state
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446124879-22240-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We check these to determine firmware loading status. Include
them to help to debug causes of firmware loading fails.
v2: Move all CSR specific registers to i915_reg.h (Ville)
v3: Rebase
v4: Rebase (RPM ref)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220487-32691-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
For bxt CSR firmware exposes a count of dc5 entries. Expose
it through debugs
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The CSR firmware expose two counters, handy to check if we are indeed
entering DC5/DC6.
v2: Rebase
v3: Take RPM ref before reading (Imre)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220412-32574-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Create a new debufs file for it, we'll have a few more things to add
there.
v2: Fix checkpatch warning about static const array
v3: use named initializers (Ville)
v4: strip out csr_state as it will be removed in future (Ville, Imre)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445950025-5793-3-git-send-email-mika.kuoppala@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
There is known issue on GT interrupt delivery with DC6 and
firmwares <1.21. There is a suspicion that this causes
spurious gpu hangs on driver init and with some workloads,
as upgrading the firmware to 1.21 makes these problems
disappear.
As of now the current version included in distribution
firmware packages is very like to be 1.19. Play it safe and
refuse to load a firmware version that may affect gpu
side stability.
With < 1.23 there is a palette and dmc ram corruption issue
so blacklist anything below that.
v2: Refuse to load fw instead of notifying the user
v3: Rebase on header version changes
v4: Refuse to load anything less than 1.23
v5: Give enough information for user for finding correct fw (Chris)
v6: better url and formatting (Chris)
v7: move error log for each fail path (Mika)
bail out earlier in load path (Imre)
v8: Fix the version check (Imre)
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: https://01.org/linuxgraphics/downloads/skldmcver121
References: https://01.org/linuxgraphics/downloads/skylake-dmc-1.23
Testcase: igt/gem_exec_nop
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220336-32392-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
That can be handy later on to tell which DMC firmware version the user
has, by just looking at the dmesg.
v2: use DRM_DEBUG_DRIVER (Chris)
v3: use DRM_INFO (Marc Herbert)
Cc: Marc Herbert <marc.herbert@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445950025-5793-1-git-send-email-mika.kuoppala@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We had two failure modes here:
1.
Deadlock in intelfb_alloc failure path where it calls
drm_framebuffer_remove, which grabs the struct mutex and intelfb_create
(caller of intelfb_alloc) was already holding it.
2.
Deadlock in intelfb_create failure path where it calls
drm_framebuffer_unreference, which grabs the struct mutex and
intelfb_create was already holding it.
[Daniel Vetter on why struct_mutex needs to be locked in the second half
of intelfb_create: "The vma [for the fbdev] is pinned, the problem is
that we re-lookup it a few times, which is racy. We should instead track
the vma directly, but oh well we don't."]
v2:
* Reformat commit msg to 72 chars. (Lukas Wunner)
* Add third failure mode. (Lukas Wunner)
v5:
* Rebase on drm-intel-nightly 2015y-09m-01d-09h-06m-08s UTC,
rephrase commit message. (Jani Nicula)
v6:
* In intelfb_alloc, if __intel_framebuffer_create failed,
fb will be an ERR_PTR, thus not null. So in the failure
path we need to check for IS_ERR_OR_NULL to avoid calling
drm_framebuffer_remove on the ERR_PTR. (Lukas Wunner)
* Since this is init code a drm_framebuffer_unreference should
be all we need. drm_framebuffer_remove is for framebuffers
that userspace has created - and is getting somewhat
defeatured. (Daniel Vetter)
v7:
* Clarify why struct_mutex needs to be locked in the second half
of intelfb_create. (Daniel Vetter)
Fixes: 60a5ca015f ("drm/i915: Add locking around
framebuffer_references--")
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[Lukas: Create v3 + v4 + v5 + v6 + v7 based on Tvrtko's v2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/47d4e88c91b3bf0f7a280cabec54c8c8cf0cf6f2.1446892879.git.lukas@wunner.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In intelfb_alloc(), if the call to intel_pin_and_fence_fb_obj() fails,
the bo is unrefed twice: By drm_framebuffer_remove() and once more by
drm_gem_object_unreference(). Fix it.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/cd7b33330621a350b0159ec5e098297b139cfaf7.1446892879.git.lukas@wunner.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently when allocating a framebuffer fails, the gem object gets
unrefed at the bottom of the call stack in __intel_framebuffer_create,
not where it gets refed, which is in intel_framebuffer_create_for_mode
(via i915_gem_alloc_object) and in intel_user_framebuffer_create
(via drm_gem_object_lookup).
This invites mistakes: __intel_framebuffer_create is also called from
intelfb_alloc, and as discovered by Tvrtko Ursulin, a double unref
was introduced there with a8bb681827 ("drm/i915: Fix error path leak
in fbdev fb allocation").
As suggested by Ville Syrjälä, fix the double unref and improve code
clarity by moving the unref away from __intel_framebuffer_create to
where the gem object gets refed.
Based on Tvrtko Ursulin's original v2.
v3: On fb alloc failure, unref gem object where it gets refed,
fix double unref in separate commit (Ville Syrjälä)
v4: Lock struct_mutex on unref (Chris Wilson)
v5: Rebase on drm-intel-nightly 2015y-09m-01d-09h-06m-08s UTC,
rephrase commit message (Jani Nicula)
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
[MBP 5,3 2009 nvidia MCP79 + G96 pre-retina]
Tested-by: Paul Hordiienko <pvt.gord@gmail.com>
[MBP 6,2 2010 intel ILK + nvidia GT216 pre-retina]
Tested-by: William Brown <william@blackhats.net.au>
[MBP 8,2 2011 intel SNB + amd turks pre-retina]
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina]
Tested-by: Bruno Bierbaumer <bruno@bierbaumer.net>
[MBP 11,3 2013 intel HSW + nvidia GK107 retina]
Fixes: a8bb681827 ("drm/i915: Fix error path leak in fbdev fb
allocation")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/2161c5062ef5d6458f8ae14d924a26d4d1dba317.1446892879.git.lukas@wunner.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In order to prepare for a link training with DDI, the state machine
would call intel_ddi_prepare_link_retrain(). To remove the dependency to
the hardware information, replace that direct call with a callback.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-7-git-send-email-ander.conselvan.de.oliveira@intel.com
Move register write from intel_dp_update_link_train() into
intel_dp_set_signal_levels(). This creates a better split between the
i915 specific code and the generic link training part. Note that this
causes an extra register write in intel_dp_reset_link_train(), since
both intel_dp_set_signal_levels() and intel_dp_set_link_train() write
to the DP register.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-5-git-send-email-ander.conselvan.de.oliveira@intel.com
Move the call to intel_dp_get_adjust_train() out of
intel_dp_update_link_train() and call it instead from the clock recovery
and channel equalization features. A follow up patch will remove the DP
register write from that function, so that it handles only the DPCD
write.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-4-git-send-email-ander.conselvan.de.oliveira@intel.com
It just makes the code more confusing, so just reference intel_dp_>DP
directly.
Note that this also fix a bug where the value of intel_dp->DP could be
different than the last value written to the hw, due to an early return
that would skip the 'intel_dp->DP = DP' line.
v2: Don't preserve old DP value on failure. (Sivakumar)
- Don't call drm_dp_clock_recovery_ok() twice. (Sivakumar)
- Keep return type of clock recovery and channel equalization
functions as void. (Ander)
v3: Remove DP parameter from intel_dp_set_signal_levels(). (Sivakumar)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-2-git-send-email-ander.conselvan.de.oliveira@intel.com
SWF18 is set if the display has been initialized by the pre-os. It also
gives what configuration is enabled on which pipe. In skl_sanitize_cdclk,
the DPLL sanity check can pass even if GOP/VBIOS is not loaded as BIOS
enables DPLL for integrated audio codec related programming.
So fisrt check if SWF18 is set and then follow through with other DPLL
and CDCLK verification. If not set then for sure we need to sanitize the
cdclock.
v2: Update the commit message for clarity (Siva)
v3: Correct the mask to check for bits[23:0] instead of only bits[16:0].
Had missed checking for PIPE C altogether. Remaining are reserved (Siva)
v4: Use ILK_SWF macro for SWF register definitions. Taken from Ville's patch
http://lists.freedesktop.org/archives/intel-gfx/2015-November/079480.html
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446726932-14078-1-git-send-email-shobhit.kumar@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BXT CRTC scaling uses the same gen9 codepaths as SKL; these codepaths
store panel fitter information in pipe_config->pch_pfit. However since
HAS_PCH_SPLIT() is false for BXT we never actually wind up filling in
this structure (we wind up filling in pipe_config->gmch_pfit instead,
which is ignored when we go to program the hardware). Make sure we
always take the PCH code path on gen9+ platforms.
v2: Use HAS_GMCH_DISPLAY() to more cleanly describe the platforms that
actually want to use GMCH-style panel fitting. (Ville)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446656727-3516-1-git-send-email-matthew.d.roper@intel.com
I wanted to add yet another check to intel_fbc_update() and realized
I would need to create yet another enum no_fbc_reason case. So I
remembered this patch series that Damien wrote a long time ago and
nobody ever reviewed, so I decided to reimplement it since the code
changed a lot since then.
Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445964628-30226-2-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Make pinning and waiting a separate step, and wait for object idle
without struct_mutex held.
Changes since v1:
- Do not wait when a reset is in progress.
- Remove call to i915_gem_object_wait_rendering for
intel_overlay_do_put_image (Chris Wilson)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
struct_mutex is being locked for every plane in intel_prepare_plane_fb
and intel_cleanup_plane_fb.
Require the caller to hold the mutex, and only acquire the mutex for
each helper call. This way the lock only needs to be acquired
twice in ->atomic_commit(). Once for pinning new framebuffers at the
start, the second time for unpinning old framebuffer.
Changes since v1:
- Use mutex_lock_interruptible instead of i915 variant,
to prevent a deadlock when called from the reset code.
Changes since v2:
- Clarify struct_mutex is locked by the caller.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com> #v1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Move it from intel_crtc_atomic_commit to prepare_plane_fb.
Waiting is done before committing, otherwise it's too late
to undo the changes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Extends i915_display_info so that for each active crtc also print
all planes associated with the pipe. This patch shows information
about each plane wrt format, size, position, rotation, and scaling.
This is very useful when debugging user space compositors that try
to utilize several planes for a commit.
V2: Fixed comments from Maarten, Ville, and Chris. Fixed printing of
16.16 fixpoint, better rotation bitmask management and some minor fixes
V3: Corrected state->src_x & 0x00ff to state->src_x & 0xffff...
Signed-off-by: Robert Fekete <robert.fekete@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445961512-25317-1-git-send-email-robert.fekete@linux.intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
One branch of the if clause uses pr_info, the other pr_err; change
the 'false' branch to also use pr_info. This minor oversight has gone
unfixed since the initial vga_switcheroo implementation in 6a9ee8af.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446246960-22620-1-git-send-email-adi@adirat.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
DRM_ERROR an continue without any issues aren't allowed since that
causes noise in the CI system. But we absolutely want to have the
DRM_ERROR when we want to run with GuC.
For simplicity just short-circuit all the loader code when it's not
needed.
v2: Mika&Chris complained that I shouldn't hit send on patches written
before coffee kicks in.
v3: Make it compile at least ...
Cc: Alex Dai <yu.dai@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445591459-4327-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: (Rodrigo) Rebase after commit 3cb27f38f
("drm/i915: remove an extra level of indirection in PCI ID list")
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446060072-19489-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
v2: separate out device info into different GT (Damien)
v3: Add is_kabylake to the KBL gt3 structuer (Damien)
Sort the platforms in older -> newer order (Damien)
v4: Split platform definition since is_skylake=1 on
kabylake structure was Nacked. (Rodrigo)
v5: (Rodrigo) Rebase after commit 3cb27f38f
("drm/i915: remove an extra level of indirection in PCI ID list")
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446059991-17033-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Kabylake is a Intel® Processor containing Intel® HD Graphics
following Skylake.
It is Gen9p5, so it inherits everything from Skylake.
Let's start by adding the platform separated from Skylake
but reusing most of all features, functions etc. Later we
rebase the PCI-ID patch without is_skylake=1
so we don't replace what original Author did there.
Few IS_SKYLAKEs if statements are not being covered by this patch
on purpose:
- Workarounds: Kabylake is derivated from Skylake H0 so no
W/As apply here.
- GuC: A following patch removes Kabylake support with an
explanation: No firmware available yet.
- DMC/CSR: Done in a separated patch since we need to be carefull
and load the version for revision 7 since
Kabylake is Skylake H0.
v2: relative cleaner commit message and added the missed
IS_KABYLAKE to intel_i2c.c as pointed out by Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add the PCI IDs directly in the pciidlist array instead of defining an
extra macro. The minor benefit from this is neater diffs when adding to
the end of the list.
v2: drop the "aka" comment (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446053589-21283-1-git-send-email-jani.nikula@intel.com
Having flushed all requests from all queues, we know that all
ringbuffers must now be empty. However, since we do not reclaim
all space when retiring the request (to prevent HEADs colliding
with rapid ringbuffer wraparound) the amount of available space
on each ringbuffer upon reset is less than when we start. Do one
more pass over all the ringbuffers to reset the available space
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Include an early NEEDS_FORCEWAKE() check for vlv and chv.
Hopefully that will avoid doing so many range checks in for many
register accesses (at least for all display registers).
Note that vlv already had the check in the write path since it shares
the gen6+ code for that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Change the fw domain handling in the vlv/chv register read/write
functions to look more like the SKL code, ie. have a single
__force_wake_get() get call instead of multiple ones.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Change FORCEWAKE & co. reads for the error state to use I915_READ_FW().
Reading a FORCEWAKE register using a function that can frob forcewake
just seems wrong.
There is a check to skip grabbing the forcewake for accessing FORCEWAKE
in intel_uncore.c, but there's no such check for FORCEWAKE_MT. So no
idea what is currently happening with FORCEWAKE_MT reads. FORCEWAKE_VLV
is fortunately outside the forcewake range anyway, so no actual issue
with that one.
So let's just make the rule that you can't access FORCEWAKE registers with
the normal I915_READ() stuff, and we can drop the extra FORCEWAKE check
from NEEDS_FORCEWAKE(). While at it use NEEDS_FORCEWAKE() on BDW, where
it was skipped for whatever bikeshed reason that I've already forgotten.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
There's no need for __raw_i915_read8() & co. to be macros, so make them
inline functions. To avoid typo mistakes generate the inline functions
using preprocessor templates.
We have a few users of the raw register acces functions outside
intel_uncore.c, so let's also move the functions into intel_drv.h.
While doing that switch I915_READ_FW() & co. to use the
__raw_i915_read() functions, and use the _FW macros everywhere
outside intel_uncore.c where we want to read registers without
grabbing forcewake and whatnot. The only exception is
i915_check_vgpu() which itself gets called from intel_uncore.c,
so using the __raw_i915_read stuff there seems appropriate.
v2: Squash in the intel_uncore.c->i915_drv.h move
Convert I915_READ_FW() to use __raw_i915_read(), and use
I915_READ_FW() outside of intel_uncore.c (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we're not synchronizing the ring request list during error state capture
the request list state might change between the time the corresponding error
request list was allocated and dimensioned to the time when the ring request
list is actually captured into the error state. If this happens then do an
early exit and be aware that the captured error state might not be fully
reliable.
* v2:
- Chris Wilson: Removed WARN_ON from size check since having the error state
request list and the live driver request list diverge like this is a
legitimate behaviour.
- Tomas Elf: Removed update of num_request field since this made no sense. Just
exit and move on.
* v3:
- Chris Wilson: Removed error message at the point of early exit. The user is
not interested in any state changes happening during the error state capture,
only in the state that we're trying to capture at the point of the error.
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 5105672341.
I somehow managed to combine a patch from Tomas Elf with a totally
unrelated commit message from Chris Wilson. Let's revert this and
reapply properly.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
