All the called functions expect interrupts to be enabled, and
now one of them has started to warn about it, so make it correct.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The device had an undocumented "feature": it can provide a sequence of
spurious link-down status data even if the link is up all the time.
A sequence of 10 was seen so update the link state only after the device
reports the same link state 20 times.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Tested-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not easy to use in4_pton() correctly without reading
its definition, so add some doc for it.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not easy to use in6_pton() correctly without reading
its definition, so add some doc for it.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use be32_to_cpu instead of htonl to keep sparse happy.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit e2446eaa ("tcp_v4_send_reset: binding oif to iif in no
sock case").. tcp resets are always lost, when routing is asymmetric.
Yes, backing out that patch will result in misrouting of resets for
dead connections which used interface binding when were alive, but we
actually cannot do anything here. What's died that's died and correct
handling normal unbound connections is obviously a priority.
Comment to comment:
> This has few benefits:
> 1. tcp_v6_send_reset already did that.
It was done to route resets for IPv6 link local addresses. It was a
mistake to do so for global addresses. The patch fixes this as well.
Actually, the problem appears to be even more serious than guaranteed
loss of resets. As reported by Sergey Soloviev <sol@eqv.ru>, those
misrouted resets create a lot of arp traffic and huge amount of
unresolved arp entires putting down to knees NAT firewalls which use
asymmetric routing.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
* allow kernel_execve() leave the actual return to userland to
caller (selected by CONFIG_GENERIC_KERNEL_EXECVE). Callers
updated accordingly.
* architecture that does select GENERIC_KERNEL_EXECVE in its
Kconfig should have its ret_from_kernel_thread() do this:
call schedule_tail
call the callback left for it by copy_thread(); if it ever
returns, that's because it has just done successful kernel_execve()
jump to return from syscall
IOW, its only difference from ret_from_fork() is that it does call the
callback.
* such an architecture should also get rid of ret_from_kernel_execve()
and __ARCH_WANT_KERNEL_EXECVE
This is the last part of infrastructure patches in that area - from
that point on work on different architectures can live independently.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert cpu_to_le32(le32_to_cpu(E1) + E2) to use le32_add_cpu().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use the ACCESS_ONCE macro in dm-bufio and dm-verity where a variable
can be modified asynchronously (through sysfs) and we want to prevent
compiler optimizations that assume that the variable hasn't changed.
(See Documentation/atomic_ops.txt.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use list_move() instead of list_del() + list_add().
spatch with a semantic match was used to find this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The mpio dereference should be moved below the BUG_ON NULL test
in multipath_end_io().
spatch with a semantic match was used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQeBKDAAoJEFjIrFwIi8fJDpwH/3nPBH82pJVxdLPBnmJhWuJR
voSPP0m9i69w/mc7wHtiRwK4lRMAUidgS77iBZkIT2cY0/NYvOKKBlMUitkYJFlK
dTVqr9O4iQcuG2yQk8+mXxC6NLH1VKOnSIyhqRswrePoBKzoHi/x7Y462a+tbxa9
lGBHT9/SqeYXyItRfkdfmAXFZcqIJqLRXEwRMvbky1U3s2QGy7CdIQgra0zWF+t1
ashNpaEBpH9Jy60VSpQtMpx8hWxd0W2NirNu+nACtTE5/MeuiBvKlPdEPC/rUbdJ
c5j5VYLjSxPCheY0sajK6pxKgHdfiqmMRlutzMVj3Egwilb0LBxv1018gRFzBu8=
=/qCG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"This has four bug-fixes and one tiny feature that I forgot to put
initially in my tree due to oversight.
The feature is for kdump kernels to speed up the /proc/vmcore reading.
There is a ram_is_pfn helper function that the different platforms can
register for. We are now doing that.
The bug-fixes cover some embarrassing struct pv_cpu_ops variables
being set to NULL on Xen (but not baremetal). We had a similar issue
in the past with {write|read}_msr_safe and this fills the three
missing ones. The other bug-fix is to make the console output (hvc)
be capable of dealing with misbehaving backends and not fall flat on
its face. Lastly, a quirk for older XenBus implementations that came
with an ancient v3.4 hypervisor (so RHEL5 based) - reading of certain
non-existent attributes just hangs the guest during bootup - so we
take precaution of not doing that on such older installations.
Feature:
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not
used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console."
* tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pv-on-hvm kexec: add quirk for Xen 3.4 and shutdown watches.
xen/bootup: allow {read|write}_cr8 pvops call.
xen/bootup: allow read_tscp call for Xen PV guests.
xen pv-on-hvm: add pfn_is_ram helper for kdump
xen/hvc: handle backend CLOSED without CLOSING
Pull SLAB fix from Pekka Enberg:
"This contains a lockdep false positive fix from Jiri Kosina I missed
from the previous pull request."
* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm, slab: release slab_mutex earlier in kmem_cache_destroy()
Pull timer core update from Thomas Gleixner:
- Bug fixes (one for a longstanding dead loop issue)
- Rework of time related vsyscalls
- Alarm timer updates
- Jiffies updates to remove compile time dependencies
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Cast raw_interval to u64 to avoid shift overflow
timers: Fix endless looping between cascade() and internal_add_timer()
time/jiffies: bring back unconditional LATCH definition
time: Convert x86_64 to using new update_vsyscall
time: Only do nanosecond rounding on GENERIC_TIME_VSYSCALL_OLD systems
time: Introduce new GENERIC_TIME_VSYSCALL
time: Convert CONFIG_GENERIC_TIME_VSYSCALL to CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Move update_vsyscall definitions to timekeeper_internal.h
time: Move timekeeper structure to timekeeper_internal.h for vsyscall changes
jiffies: Remove compile time assumptions about CLOCK_TICK_RATE
jiffies: Kill unused TICK_USEC_TO_NSEC
alarmtimer: Rename alarmtimer_remove to alarmtimer_dequeue
alarmtimer: Remove unused helpers & defines
alarmtimer: Use hrtimer per-alarm instead of per-base
alarmtimer: Implement minimum alarm interval for allowing suspend
Pull scheduler fixes from Ingo Molnar:
"A CPU hotplug related crash fix and a nohz accounting fixlet."
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Update sched_domains_numa_masks[][] when new cpus are onlined
sched: Ensure 'sched_domains_numa_levels' is safe to use in other functions
nohz: Fix one jiffy count too far in idle cputime
Pull RCU fixes from Ingo Molnar:
"This tree includes a shutdown/cpu-hotplug deadlock fix and a
documentation fix."
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Advise most users not to enable RCU user mode
rcu: Grace-period initialization excludes only RCU notifier
The commit 254d1a3f02, titled
"xen/pv-on-hvm kexec: shutdown watches from old kernel" assumes that the
XenBus backend can deal with reading of values from:
"control/platform-feature-xs_reset_watches":
... a patch for xenstored is required so that it
accepts the XS_RESET_WATCHES request from a client (see changeset
23839:42a45baf037d in xen-unstable.hg). Without the patch for xenstored
the registration of watches will fail and some features of a PVonHVM
guest are not available. The guest is still able to boot, but repeated
kexec boots will fail."
Sadly this is not true when using a Xen 3.4 hypervisor and booting a PVHVM
guest. We end up hanging at:
err = xenbus_scanf(XBT_NIL, "control",
"platform-feature-xs_reset_watches", "%d", &supported);
This can easily be seen with guests hanging at xenbus_init:
NX (Execute Disable) protection: active
SMBIOS 2.4 present.
DMI: Xen HVM domU, BIOS 3.4.0 05/13/2011
Hypervisor detected: Xen HVM
Xen version 3.4.
Xen Platform PCI: I/O protocol version 1
... snip ..
calling xenbus_init+0x0/0x27e @ 1
Reverting the commit or using the attached patch fixes the issue. This fix
checks whether the hypervisor is older than 4.0 and if so does not try to
perform the read.
Fixes-Oracle-Bug: 14708233
CC: stable@vger.kernel.org
Acked-by: Olaf Hering <olaf@aepfle.de>
[v2: Added a comment in the source code]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We actually do not do anything about it. Just return a default
value of zero and if the kernel tries to write anything but 0
we BUG_ON.
This fixes the case when an user tries to suspend the machine
and it blows up in save_processor_state b/c 'read_cr8' is set
to NULL and we get:
kernel BUG at /home/konrad/ssd/linux/arch/x86/include/asm/paravirt.h:100!
invalid opcode: 0000 [#1] SMP
Pid: 2687, comm: init.late Tainted: G O 3.6.0upstream-00002-gac264ac-dirty #4 Bochs Bochs
RIP: e030:[<ffffffff814d5f42>] [<ffffffff814d5f42>] save_processor_state+0x212/0x270
.. snip..
Call Trace:
[<ffffffff810733bf>] do_suspend_lowlevel+0xf/0xac
[<ffffffff8107330c>] ? x86_acpi_suspend_lowlevel+0x10c/0x150
[<ffffffff81342ee2>] acpi_suspend_enter+0x57/0xd5
CC: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The hypervisor will trap it. However without this patch,
we would crash as the .read_tscp is set to NULL. This patch
fixes it and sets it to the native_read_tscp call.
CC: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
The con_debug_leave/con_debug_enter functions are stubbed out
by defining them to (0), which causes harmless build warnings.
Using proper inline functions is the normal way to deal with
this.
Without this patch, building the ARM bcm2835_defconfig results in:
drivers/tty/serial/kgdboc.c: In function 'kgdboc_pre_exp_handler':
drivers/tty/serial/kgdboc.c:279:3: warning: statement with no effect [-Wunused-value]
drivers/tty/serial/kgdboc.c: In function 'kgdboc_post_exp_handler':
drivers/tty/serial/kgdboc.c:293:3: warning: statement with no effect [-Wunused-value]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
It is possible to miss data when using the kdb pager. The kdb pager
does not pay attention to the maximum column constraint of the screen
or serial terminal. This result is not incrementing the shown lines
correctly and the pager will print more lines that fit on the screen.
Obviously that is less than useful when using a VGA console where you
cannot scroll back.
The pager will now look at the kdb_buffer string to see how many
characters are printed. It might not be perfect considering you can
output ASCII that might move the cursor position, but it is a
substantially better approximation for viewing dmesg and trace logs.
This also means that the vt screen needs to set the kdb COLUMNS
variable.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
If you press 'q' the pager should exit instead of printing everything
from dmesg which can really bog down a 9600 baud serial link.
The same is true for the bta command.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
It is a common enough mistake for people to specify "kdb" when they
meant to type "kbd" that the kgdboc can just accept both since they
both mean the same thing anyway. Specifically it is for the case
where you want kdb to be active on your graphics console + keyboard
(where kbd was the original abbreviation for keyboard).
With this change kgdboc will now accept either to mean the same thing:
kgdboc=kbd
kgdboc=kdb
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
When compiling without CONFIG_DEBUG_RODATA the following
compiler warning is generated:
arch/x86/kernel/kgdb.c: In function 'kgdb_arch_set_breakpoint':
arch/x86/kernel/kgdb.c:749: warning: unused variable 'opc'
The variable instantiation needs to be inside the #ifdef to
make the warning go away.
Reported-by: Thiago Rafael Becker <trbecker@trbecker.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This fault was detected using the kgdb test suite on boot and it
crashes recursively due to the fact that CONFIG_KPROBES on mips adds
an extra die notifier in the page fault handler. The crash signature
looks like this:
kgdbts:RUN bad memory access test
KGDB: re-enter exception: ALL breakpoints killed
Call Trace:
[<807b7548>] dump_stack+0x20/0x54
[<807b7548>] dump_stack+0x20/0x54
The fix for now is to have kgdb return immediately if the fault type
is DIE_PAGE_FAULT and allow the kprobe code to decide what is supposed
to happen.
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Allow gdb to auto load kernel modules when it is attached,
which makes it trivially easy to debug module init functions
or pre-set breakpoints in a kernel module that has not loaded yet.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
First, it's incorrect to call putname() after __getname_gfp() since the
bare __getname_gfp() call skips the auditing code, while putname()
doesn't.
mount_block_root allocates a PATH_MAX buffer via __getname_gfp, and then
calls get_fs_names to fill the buffer. That function can call
get_filesystem_list which assumes that that buffer is a full page in
size. On arches where PAGE_SIZE != 4k, then this could potentially
overrun.
In practice, it's hard to imagine the list of filesystem names even
approaching 4k, but it's best to be safe. Just allocate a page for this
purpose instead.
With this, we can also remove the __getname_gfp() definition since there
are no more callers.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In order to accomodate retrying path-based syscalls, we need to add a
new "type" argument to audit_inode_child. This will tell us whether
we're looking for a child entry that represents a create or a delete.
If we find a parent, don't automatically assume that we need to create a
new entry. Instead, use the information we have to try to find an
existing entry first. Update it if one is found and create a new one if
not.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In the cases where we already know the length of the parent, pass it as
a parm so we don't need to recompute it. In the cases where we don't
know the length, pass in AUDIT_NAME_FULL (-1) to indicate that it should
be determined.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently, this gets set mostly by happenstance when we call into
audit_inode_child. While that might be a little more efficient, it seems
wrong. If the syscall ends up failing before audit_inode_child ever gets
called, then you'll have an audit_names record that shows the full path
but has the parent inode info attached.
Fix this by passing in a parent flag when we call audit_inode that gets
set to the value of LOOKUP_PARENT. We can then fix up the pathname for
the audit entry correctly from the get-go.
While we're at it, clean up the no-op macro for audit_inode in the
!CONFIG_AUDITSYSCALL case.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For now, we just have two possibilities:
UNKNOWN: for a new audit_names record that we don't know anything about yet
NORMAL: for everything else
In later patches, we'll add other types so we can distinguish and update
records created under different circumstances.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Most of the callers get called with an inode and dentry in the reverse
order. The compiler then has to reshuffle the arg registers and/or
stack in order to pass them on to audit_inode_child.
Reverse those arguments for a micro-optimization.
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If name is NULL then the condition in the loop will never be true. Also,
with this change, we can eliminate the check for n->name == NULL since
the equivalence check will never be true if it is.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In some cases, we were passing in NULL even when we have a dentry.
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As best I can tell, whenever retval == 0, nd->path.dentry and nd->inode
are also non-NULL. Eliminate those checks and the superfluous
audit_context check.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull second set of media updates from Mauro Carvalho Chehab:
"Despite its size, most of the stuff here is trivial. This series
contains:
- s5p-mfc: additions at the driver and at the core to support H.264
hardware codec;
- Some improvements at s5p and davinci embedded drivers;
- Some V4L2 compliance fixes applied on a few drivers;
- Several random trivial patches, including several fixes and a few
new board support additions;
Notes:
1) Some Exynos media patches were dependent on some -arm fixes that
got merged on changeset 782cd9e. That's why this pull request is
based that changeset.
2) As promised, I reviewed the pending VB2 DMABUF series.
While setting a test environment, it was noticed that the upstream
support for Samsung Exynos 4 boards (smdk310 and Origen) are
broken upstream, likely due to regressions: both defconfigs are
wrong and regulator settings for both boards are broken. That,
allied with some bug at the dummy regulator driver, causes OOPSes
during boot time.
Long story short: even fixing the above, the proposed patches
OOPSed when running the DMABUF test. Not sure yet if the OOPSes
are due to some other undetected regressions, or due to some bug
on the patches.
Due to the above, DMABUF patches for vb2 got NACKed for 3.7."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Conflicts:
arch/arm/mach-davinci/include/mach/da8xx.h
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=UKY/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull second set of pinctrl patches from Linus Walleij:
"Here is a late pinctrl pull request with stuff that wasn't quite
tested at the first pull request.
The main reason to not hold off is that the modifications to
irq_domain_add_simple() as reviewed by Rob Herring introduce new
infrastructure for irqdomains that will be useful for the next cycle:
instead of sprinkling irq descriptor allocation all over the kernel
wherever a "legacy" domain is registered, which is necessary for any
platform using sparse IRQs, and many irq chips are say GPIO
controllers which may be used with several systems, some with sparse
IRQs some not, we push this into the irq_domain_add_simple() so we can
atleast do mistakes in one place.
The irq_domain_add_simple() is currently unused in the kernel, so I
need to provide a user. The Nomadik stuff that goes with are changes
to the driver I use day-to-day to make use of this facility (and a
dependency), so see it as a way to eat my own dogfood: if this blows
up the egg hits my face.
A second round of pinctrl patches for v3.7:
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller."
* tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: use simple or linear IRQ domain
irqdomain: augment add_simple() to allocate descs
pinctrl/nomadik: support other alternate-C functions
Pull second set of ARM updates from Russell King:
"This is the second set of ARM updates for this merge window.
Contained within are changes to allow the kernel to boot in hypervisor
mode on CPUs supporting virtualization, and cache flushing support to
the point of inner sharable unification, which are used by the
suspend/resume code to avoid having to do a full cache flush.
Also included is one fix for VFP code identified by Michael Olbrich."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: vfp: fix saving d16-d31 vfp registers on v6+ kernels
ARM: 7549/1: HYP: fix boot on some ARM1136 cores
ARM: 7542/1: mm: fix cache LoUIS API for xscale and feroceon
ARM: mm: update __v7_setup() to the new LoUIS cache maintenance API
ARM: kernel: update __cpu_disable to use cache LoUIS maintenance API
ARM: kernel: update cpu_suspend code to use cache LoUIS operations
ARM: mm: rename jump labels in v7_flush_dcache_all function
ARM: mm: implement LoUIS API for cache maintenance ops
ARM: virt: arch_timers: enable access to physical timers
ARM: virt: Add CONFIG_ARM_VIRT_EXT option
ARM: virt: Add boot-time diagnostics
ARM: virt: Update documentation for hyp mode entry support
ARM: zImage/virt: hyp mode entry support for the zImage loader
ARM: virt: allow the kernel to be entered in HYP mode
ARM: opcodes: add __ERET/__MSR_ELR_HYP instruction encoding
This update contains a few cleanup works, regression/stable fixes
gathered since the last pull request.
- Clean up with generic hd-audio jack handling code by David
Henningsson
- A few regression fixes for standardized HD-audio auto-parser
- Misc clean-up and small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=ehiy
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates #2 from Takashi Iwai:
"This update contains a few cleanup works, regression/stable fixes
gathered since the last pull request.
- Clean up with generic hd-audio jack handling code by David
Henningsson
- A few regression fixes for standardized HD-audio auto-parser
- Misc clean-up and small fixes"
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - do not detect jack on internal speakers for Realtek
ALSA: hda - Fix missing beep on ASUS X43U notebook
ALSA: hda - Remove AZX_DCAPS_POSFIX_COMBO
ALSA: hda - Warn an allocation for an uninitialized array
ALSA: hda/cirrus - Add missing init/free of hda_gen_spec
ALSA: hda - Fix memory leaks at error path in patch_cirrus.c
ALSA: hda - Add missing hda_gen_spec to struct via_spec
ALSA: hda - remove "Mic Jack Mode" for headset jacks (Latitude Exx30)
ALSA: hda - make Cirrus codec use generic unsol event handler
ALSA: hda - make VIA codec use generic unsol event handler
ALSA: hda - Remove dead GPIO code for VIA codec
ALSA: usb-audio: Add TASCAM US122 MKII playback
Pull pile 2 of vfs updates from Al Viro:
"Stuff in this one - assorted fixes, lglock tidy-up, death to
lock_super().
There'll be a VFS pile tomorrow (with patches from Jeff Layton,
sanitizing getname() and related parts of audit and preparing for
ESTALE fixes), but I'd rather push the stuff in this one ASAP - some
of the bugs closed here are quite unpleasant."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: bogus warnings in fs/namei.c
consitify do_mount() arguments
lglock: add DEFINE_STATIC_LGLOCK()
lglock: make the per_cpu locks static
lglock: remove unused DEFINE_LGLOCK_LOCKDEP()
MAX_LFS_FILESIZE definition for 64bit needs LL...
tmpfs,ceph,gfs2,isofs,reiserfs,xfs: fix fh_len checking
vfs: drop lock/unlock super
ufs: drop lock/unlock super
sysv: drop lock/unlock super
hpfs: drop lock/unlock super
fat: drop lock/unlock super
ext3: drop lock/unlock super
exofs: drop lock/unlock super
dup3: Return an error when oldfd == newfd.
fs: handle failed audit_log_start properly
fs: prevent use after free in auditing when symlink following was denied
