Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtnl_fill_statsinfo() is filling skb with one mandatory if_stats_msg structure.
nlmsg_put(skb, pid, seq, type, sizeof(struct if_stats_msg), flags);
But if_nlmsg_stats_size() never considered the needed storage.
This bug did not show up because alloc_skb(X) allocates skb with
extra tailroom, because of added alignments. This could very well
be changed in the future to have deterministic behavior.
Fixes: 10c9ead9f3 ("rtnetlink: add new RTM_GETSTATS message to dump link stats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap") sets
unix domain socket peer state to TCP_CLOSE in unix_shutdown. This could
happen when the local end is shutdown but the other end is not. Then,
the other end will get read or write failures which is not expected.
Fix the issue by setting the local state to shutdown.
Fixes: 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap")
Reported-by: Casey Schaufler <casey@schaufler-ca.com>
Suggested-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jiang Wang <jiang.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211004232530.2377085-1-jiang.wang@bytedance.com
- Add support for MediaTek MT7922 and MT7921
- Enable support for AOSP extention in Qualcomm WCN399x and Realtek
8822C/8852A.
- Add initial support for link quality and audio/codec offload.
- Rework of sockets sendmsg to avoid locking issues.
- Add vhci suspend/resume emulation.
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE7E6oRXp8w05ovYr/9JCA4xAyCykFAmFXkGYZHGx1aXoudm9u
LmRlbnR6QGludGVsLmNvbQAKCRD0kIDjEDILKVQdD/9dtVeMRjzAQbvPI5InAi4N
AjEy7IUAV27AE0QVZW/Q201BNnFixAivDWiQXHFiTV1ocrmX/qiW15AsKOTlpVKx
BAzy97KVLPHNoNBN3XV9PwP8OovX7zkWTL/XPHzg1lIAfniWiInuQDrlU/F3TKOO
2yJOFTy3x9RrwZcXfZUHltBo6766SC40zW4H+3WA42jljOPKXR1jH6lSIzSezBFt
qsaw/CS/aW1Z8JAA8fhZurCmoljHMgRNOsnh8AfHPCYsUZSsw9ZE6wMrDUvjXBtm
Zp9pI+h3mwc9tW/BGSZSpcktUDdXlxo9cXSCrXtxHjmrUxAsNGtHmXE7adogWSHs
PaXfst8qFdsqp+kjrx+ZbMksfhhq2/ysYNIFWvSGim3VBBw5x74tu/VebSw19PjC
1ZWzOt/5J5WCBD6BTGApCQg+YTg1u9koPRG441ZwIJ82eYgIQx80Y78uj/tG7mUH
HC3GMxEwgQzYnQsDfDI936umNAgcdGw0DL7Tu71z4zM+Tn0WcvcQgHNk42zN5gZI
XMeulxdj++pUoBYweDhlgJ88lr+gTeVwvfrYGWHpNvKsfmEcQJoqBvxTS1OJvMM5
WfTwJgJCG+o4Jfj4oH2haUeMEUFQXikV0C7Dlw6MmhmcLmzhpbaMRdLQvcDocbTA
hxhxSYhK6LQTRWv2h71MMw==
=QRkQ
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for MediaTek MT7922 and MT7921
- Enable support for AOSP extention in Qualcomm WCN399x and Realtek
8822C/8852A.
- Add initial support for link quality and audio/codec offload.
- Rework of sockets sendmsg to avoid locking issues.
- Add vhci suspend/resume emulation.
====================
Link: https://lore.kernel.org/r/20211001230850.3635543-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While existing code is correct, KCSAN is reporting
a data-race in netlink_insert / netlink_sendmsg [1]
It is correct to read nlk->bound without a lock, as netlink_autobind()
will acquire all needed locks.
[1]
BUG: KCSAN: data-race in netlink_insert / netlink_sendmsg
write to 0xffff8881031c8b30 of 1 bytes by task 18752 on cpu 0:
netlink_insert+0x5cc/0x7f0 net/netlink/af_netlink.c:597
netlink_autobind+0xa9/0x150 net/netlink/af_netlink.c:842
netlink_sendmsg+0x479/0x7c0 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmsg+0x1ed/0x270 net/socket.c:2475
__do_sys_sendmsg net/socket.c:2484 [inline]
__se_sys_sendmsg net/socket.c:2482 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2482
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff8881031c8b30 of 1 bytes by task 18751 on cpu 1:
netlink_sendmsg+0x270/0x7c0 net/netlink/af_netlink.c:1891
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
__sys_sendto+0x2a8/0x370 net/socket.c:2019
__do_sys_sendto net/socket.c:2031 [inline]
__se_sys_sendto net/socket.c:2027 [inline]
__x64_sys_sendto+0x74/0x90 net/socket.c:2027
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00 -> 0x01
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 18751 Comm: syz-executor.0 Not tainted 5.14.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: da314c9923 ("netlink: Replace rhash_portid with bound")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No users in tree since commit a3498436b3 ("netns: restrict uevents"),
so remove this functionality.
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de1799667b ("net: bridge: add STP xstats")
added an additional nla_reserve_64bit() in br_fill_linkxstats(),
but forgot to update br_get_linkxstats_size() accordingly.
This can trigger the following in rtnl_stats_get()
WARN_ON(err == -EMSGSIZE);
Fixes: de1799667b ("net: bridge: add STP xstats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge_fill_linkxstats() is using nla_reserve_64bit().
We must use nla_total_size_64bit() instead of nla_total_size()
for corresponding data structure.
Fixes: 1080ab95e3 ("net: bridge: add support for IGMP/MLD stats and export them via netlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet received on a trunk will have bit 2 set in Forward DSA tagged
frame. Bit 1 can be either 0 or 1 and is otherwise undefined and bit 0
indicates the frame CFI. Masking with 7 thus results in frames as
being identified as being from a trunk when in fact they are not. Fix
the mask to just look at bit 2.
Fixes: 5b60dadb71 ("net: dsa: tag_dsa: Support reception of packets from LAG devices")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sdata->tun_src should be freed before sdata is freed
because sdata->tun_src is allocated after sdata allocation.
So, kfree(sdata) and kfree(rcu_dereference_raw(sdata->tun_src)) are
changed code order.
Fixes: f04ed7d277 ("net: ipv6: check return value of rhashtable_init")
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the ip6ip6 encapsulation by providing three encap
modes: inline, encap and auto.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prerequisite patch provides some minor edits (alignments, renames) and a
minor modification inside a function to facilitate the next patch by using
existing nla_* functions.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch anticipates the support for the IOAM insertion inside in-transit
packets, by making a difference between input and output in order to determine
the right value for its hop-limit (inherited from the IPv6 hop-limit).
Input case: happens before ip6_forward, the IPv6 hop-limit is not decremented
yet -> decrement the IOAM hop-limit to reflect the new hop inside the trace.
Output case: happens after ip6_forward, the IPv6 hop-limit has already been
decremented -> keep the same value for the IOAM hop-limit.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add multi-packet route input tests, for message reassembly. These will
feed packets to be received by a bound socket, or dropped.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for single-packet route inputs, testing the
mctp_route_input function.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for the initial packet ingress through
mctp_pkttype_receive function; mainly packet header sanity checks. Full
input routing checks will be added as a separate change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds the first kunit test for the mctp subsystem, and an
initial test for the fragmentation path.
We're adding tests under a new net/mctp/test/ directory.
Incorporates a fix for module configs:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert sw drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all packets injected into Ocelot switches are classified to
VLAN 0, regardless of whether they are VLAN-tagged or not. This is
because the switch only looks at the VLAN TCI from the DSA tag.
VLAN 0 is then stripped on egress due to REW_TAG_CFG_TAG_CFG. There are
2 cases really, below is the explanation for ocelot_port_set_native_vlan:
- Port is VLAN-aware, we set REW_TAG_CFG_TAG_CFG to 1 (egress-tag all
frames except VID 0 and the native VLAN) if a native VLAN exists, or
to 3 otherwise (tag all frames, including VID 0).
- Port is VLAN-unaware, we set REW_TAG_CFG_TAG_CFG to 0 (port tagging
disabled, classified VLAN never appears in the packet).
One can already see an inconsistency: when a native VLAN exists, VID 0
is egress-untagged, but when it doesn't, VID 0 is egress-tagged.
So when we do this:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
bridge vlan del dev swp0 vid 1
bridge vlan add dev swp0 vid 1 pvid # but not untagged
and we ping through swp0, packets will look like this:
MAC > 33:33:00:00:00:02, ethertype 802.1Q (0x8100): vlan 0, p 0,
ethertype 802.1Q (0x8100), vlan 1, p 0, ethertype IPv6 (0x86dd),
ICMP6, router solicitation, length 16
So VID 1 frames (sent that way by the Linux bridge) are encapsulated in
a VID 0 header - the classified VLAN of the packets as far as the hw is
concerned. To avoid that, what we really need to do is stop injecting
packets using the classified VLAN of 0.
This patch strips the VLAN header from the skb payload, if that VLAN
exists and if the port is under a VLAN-aware bridge. Then it copies that
VLAN header into the DSA injection frame header.
A positive side effect is that VCAP ES0 VLAN rewriting rules now work
for packets injected from the CPU into a port that's under a VLAN-aware
bridge, and we are able to match those packets by the VLAN ID that was
sent by the network stack, and not by VLAN ID 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_gro_complete always returned the same value, NET_RX_SUCCESS
And the value was not used anywhere
Signed-off-by: Gyumin Hwang <hkm73560@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net (v2)
The following patchset contains Netfilter fixes for net:
1) Move back the defrag users fields to the global netns_nf area.
Kernel fails to boot if conntrack is builtin and kernel is booted
with: nf_conntrack.enable_hooks=1. From Florian Westphal.
2) Rule event notification is missing relevant context such as
the position handle and the NLM_F_APPEND flag.
3) Rule replacement is expanded to add + delete using the existing
rule handle, reverse order of this operation so it makes sense
from rule notification standpoint.
4) Propagate to userspace the NLM_F_CREATE and NLM_F_EXCL flags
from the rule notification path.
Patches #2, #3 and #4 are used by 'nft monitor' and 'iptables-monitor'
userspace utilities which are not correctly representing the following
operations through netlink notifications:
- rule insertions
- rule addition/insertion from position handle
- create table/chain/set/map/flowtable/...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the NLM_F_CREATE and NLM_F_EXCL flags in netlink event
notifications, otherwise userspace cannot distiguish between create and
add commands.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Daniel Borkmann says:
====================
bpf-next 2021-10-02
We've added 85 non-merge commits during the last 15 day(s) which contain
a total of 132 files changed, 13779 insertions(+), 6724 deletions(-).
The main changes are:
1) Massive update on test_bpf.ko coverage for JITs as preparatory work for
an upcoming MIPS eBPF JIT, from Johan Almbladh.
2) Add a batched interface for RX buffer allocation in AF_XDP buffer pool,
with driver support for i40e and ice from Magnus Karlsson.
3) Add legacy uprobe support to libbpf to complement recently merged legacy
kprobe support, from Andrii Nakryiko.
4) Add bpf_trace_vprintk() as variadic printk helper, from Dave Marchevsky.
5) Support saving the register state in verifier when spilling <8byte bounded
scalar to the stack, from Martin Lau.
6) Add libbpf opt-in for stricter BPF program section name handling as part
of libbpf 1.0 effort, from Andrii Nakryiko.
7) Add a document to help clarifying BPF licensing, from Alexei Starovoitov.
8) Fix skel_internal.h to propagate errno if the loader indicates an internal
error, from Kumar Kartikeya Dwivedi.
9) Fix build warnings with -Wcast-function-type so that the option can later
be enabled by default for the kernel, from Kees Cook.
10) Fix libbpf to ignore STT_SECTION symbols in legacy map definitions as it
otherwise errors out when encountering them, from Toke Høiland-Jørgensen.
11) Teach libbpf to recognize specialized maps (such as for perf RB) and
internally remove BTF type IDs when creating them, from Hengqi Chen.
12) Various fixes and improvements to BPF selftests.
====================
Link: https://lore.kernel.org/r/20211002001327.15169-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
prevent_wake logic is backward since what it is really checking is
if the device may wakeup the system or not, not that it will prevent
the to be awaken.
Also looking on how other subsystems have the entry as power/wakeup
this also renames the force_prevent_wake to force_wakeup in vhci driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
napi_busy_loop() disables preemption and performs a NAPI poll. We can't acquire
sleeping locks with disabled preemption which would be required while
__napi_poll() invokes the callback of the driver.
A threaded interrupt performing the NAPI-poll can be preempted on PREEMPT_RT.
A RT thread on another CPU may observe NAPIF_STATE_SCHED bit set and busy-spin
until it is cleared or its spin time runs out. Given it is the task with the
highest priority it will never observe the NEED_RESCHED bit set.
In this case the time is better spent by simply sleeping.
The NET_RX_BUSY_POLL is disabled by default (the system wide sysctls for
poll/read are set to zero). Disabling NET_RX_BUSY_POLL on PREEMPT_RT to avoid
wrong locking context in case it is used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20211001145841.2308454-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If sd_max is unsigned, then sd_max - GSS_SEQ_WIN is a very large number
whenever sd_max is less than GSS_SEQ_WIN, and the comparison:
seq_num <= sd->sd_max - GSS_SEQ_WIN
in gss_check_seq_num is pretty much always true, even when that's
clearly not what was intended.
This was causing pynfs to hang when using krb5, because pynfs uses zero
as the initial gss sequence number. That's perfectly legal, but this
logic error causes knfsd to drop the rpc in that case. Out-of-order
sequence IDs in the first GSS_SEQ_WIN (128) calls will also cause this.
Fixes: 10b9d99a3d ("SUNRPC: Augment server-side rpcgss tracepoints")
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
This reverts commit 4f42ad2011, reversing
changes made to ea2dd331bf.
These chanfges break the build when mctp is modular.
Signed-off-by: David S. Miller <davem@davemloft.net>
Each region has an independently configurable number of maximum
snapshots. This information is not reported to userspace, making it not
very discoverable. Fix this by adding a new
DEVLINK_ATTR_REGION_MAX_SNAPSHOST attribute which is used to report this
maximum.
Ex:
$devlink region
pci/0000:af:00.0/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.0/device-caps: size 4096 snapshot [] max 10
pci/0000:af:00.1/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.1/device-caps: size 4096 snapshot [] max 10
This information enables users to understand why a new region command
may fail due to having too many existing snapshots.
Reported-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add multi-packet route input tests, for message reassembly. These will
feed packets to be received by a bound socket, or dropped.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for single-packet route inputs, testing the
mctp_route_input function.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for the initial packet ingress through
mctp_pkttype_receive function; mainly packet header sanity checks. Full
input routing checks will be added as a separate change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds the first kunit test for the mctp subsystem, and an
initial test for the fragmentation path.
We're adding tests under a new net/mctp/test/ directory.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes use of bt_skb_sendmsg instead of allocating a different
buffer to be used with memcpy_from_msg which cause one extra copy.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows
that, in the worst scenario, could lead to heap overflows.
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210929201718.GA342296@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa ("af_unix: Allow SO_PEERCRED to work across namespaces.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using snmp_get_cpu_field_batch() allows for better cpu cache
utilization, especially on hosts with large number of cpus.
Also remove special handling when mptcp mibs where not yet
allocated.
I chose to use temporary storage on the stack to keep this patch simple.
We might in the future use the storage allocated in netstat_seq_show().
Combined with prior patch (inlining snmp_get_cpu_field)
time to fetch and output mptcp counters on a 256 cpu host [1]
goes from 75 usec to 16 usec.
[1] L1 cache size is 32KB, it is not big enough to hold all dataset.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial function is called ~90,000 times on 256 cpus hosts,
when reading /proc/net/netstat. And this number keeps inflating.
Inlining it saves many cycles.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user sets SO_RESERVE_MEM socket option, in order to utilize the
reserved memory when in memory pressure state, we adjust rcv_ssthresh
according to the available reserved memory for the socket, instead of
using 4 * advmss always.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user sets SO_RESERVE_MEM socket option, in order to fully utilize the
reserved memory in memory pressure state on the tx path, we modify the
logic in sk_stream_moderate_sndbuf() to set sk_sndbuf according to
available reserved memory, instead of MIN_SOCK_SNDBUF, and adjust it
when new data is acked.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This socket option provides a mechanism for users to reserve a certain
amount of memory for the socket to use. When this option is set, kernel
charges the user specified amount of memory to memcg, as well as
sk_forward_alloc. This amount of memory is not reclaimable and is
available in sk_forward_alloc for this socket.
With this socket option set, the networking stack spends less cycles
doing forward alloc and reclaim, which should lead to better system
performance, with the cost of an amount of pre-allocated and
unreclaimable memory, even under memory pressure.
Note:
This socket option is only available when memory cgroup is enabled and we
require this reserved memory to be charged to the user's memcg. We hope
this could avoid mis-behaving users to abused this feature to reserve a
large amount on certain sockets and cause unfairness for others.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct dev_addr_list is used for device addresses, unicast addresses
and multicast addresses. The first of those needs special handling
of the main address - netdev->dev_addr points directly the data
of the entry and drivers write to it freely, so we can't maintain
it in the rbtree (for now, at least, to be fixed in net-next).
Current work around sprinkles special handling of the first
address on the list throughout the code but it missed the case
where address is being added. First address will not be visible
during subsequent adds.
Syzbot found a warning where unicast addresses are modified
without holding the rtnl lock, tl;dr is that team generates
the same modification multiple times, not necessarily when
right locks are held.
In the repro we have:
macvlan -> team -> veth
macvlan adds a unicast address to the team. Team then pushes
that address down to its memebers (veths). Next something unrelated
makes team sync member addrs again, and because of the bug
the addr entries get duplicated in the veths. macvlan gets
removed, removes its addr from team which removes only one
of the duplicated addresses from veths. This removal is done
under rtnl. Next syzbot uses iptables to add a multicast addr
to team (which does not hold rtnl lock). Team syncs veth addrs,
but because veths' unicast list still has the duplicate it will
also get sync, even though this update is intended for mc addresses.
Again, uc address updates need rtnl lock, boom.
Reported-by: syzbot+7a2ab2cdc14d134de553@syzkaller.appspotmail.com
Fixes: 406f42fa0d ("net-next: When a bond have a massive amount of VLANs with IPv6 addresses, performance of changing link state, attaching a VRF, changing an IPv6 address, etc. go down dramtically.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following flower filter fails to match non-PPP_IP{V6} packets
wrapped in PPP_SES protocol:
tc filter add dev eth0 ingress protocol ppp_ses flower \
action simple sdata hi64
The reason is that proto local variable is being set even when
FLOW_DISSECT_RET_OUT_BAD status is returned.
The fix is to avoid setting proto variable if the PPP protocol is unknown.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() and flex_array_size() helpers instead of
an open-coded version, in order to avoid any potential type mistakes
or integer overflows that, in the worse scenario, could lead to heap
overflows.
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210928193107.GA262595@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have a unit test that invokes an XDP program with 1m different
inputs, aka 1m BPF_PROG_RUN syscalls. We run this test concurrently
with slight variations in how we generated the input.
Since commit f23c4b3924 ("bpf: Start using the BPF dispatcher in BPF_TEST_RUN")
the unit test has slowed down significantly. Digging deeper reveals that
the concurrent tests are serialised in the kernel on the XDP dispatcher.
This is a global resource that is protected by a mutex, on which we contend.
Fix this by not calling into the XDP dispatcher if we only want to perform
a single run of the BPF program.
See: https://lore.kernel.org/bpf/CACAyw9_y4QumOW35qpgTbLsJ532uGq-kVW-VESJzGyiZkypnvw@mail.gmail.com/
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210928093100.27124-1-lmb@cloudflare.com
This moves code from hci_suspend_notifier to hci_{suspend,resume}_dev
since some driver may handle pm directly using
HCI_QUIRK_NO_SUSPEND_NOTIFIER they would instead call
hci_{suspend,resume}_dev directly and we want that to have the same
behavior regardless of where pm is being handled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix a build error with clang in __xp_alloc():
[...]
net/xdp/xsk_buff_pool.c:465:15: error: variable 'xskb' is uninitialized
when used here [-Werror,-Wuninitialized]
xp_release(xskb);
^~~~
This is correctly detected by clang, but not gcc. In fact, the xp_release()
statement should not be there at all in the refactored code, just remove it.
Fixes: 94033cd8e7 ("xsk: Optimize for aligned case")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20210929061403.8587-1-magnus.karlsson@gmail.com
datagram.c hasn't use any macro or function declared in linux/ip.h.
Thus, these files can be removed from datagram.c safely without
affecting the compilation of the net/ipv4 module
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
tag_ksz.c hasn't use any macro or function declared in linux/slab.h.
Thus, these files can be removed from tag_ksz.c safely without
affecting the compilation of the ./net/dsa module
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
tag_8021q.c hasn't use any macro or function declared in linux/if_bridge.h.
Thus, these files can be removed from tag_8021q.c safely without
affecting the compilation of the ./net/dsa module
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use array_size() helper instead of the open-coded version in
copy_to_user(). These sorts of multiplication factors need
to be wrapped in array_size().
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use array_size() helper instead of the open-coded version in
copy_{from,to}_user(). These sorts of multiplication factors
need to be wrapped in array_size().
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A route's RTAX_MTU can be set in nested RTAX_METRICS
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a future change, we'll want to provide a registration call for
mctp-specific devices. This requires us to have the networks established
before device driver inits, so run the core init as a subsys_initcall.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tag allocation, release and bind events are somewhat opaque outside
the kernel; this change adds a few tracepoints to assist in
instrumentation and debugging.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a MCTP (local-eid,remote-eid,tag) tuple is allocated to a
socket on send, and only expires when the socket is closed.
This change introduces a tag timeout, freeing the tuple after a fixed
expiry - currently six seconds. This is greater than (but close to) the
max response timeout in upper-layer bindings.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we tie the struct mctp_dev lifetime to the underlying struct
net_device, and hold/put that device as a proxy for a separate mctp_dev
refcount. This works because we're not holding any references to the
mctp_dev that are different from the netdev lifetime.
In a future change we'll break that assumption though, as we'll need to
hold mctp_dev references in a workqueue, which might live past the
netdev unregister notification.
In order to support that, this change introduces a refcount on the
mctp_dev, currently taken by the net_device->mctp_ptr reference, and
released on netdev unregister events. We can then use this for future
references that might outlast the net device.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will want to invalidate sk_keys in a future change, which will
require a boolean flag to mark invalidated items in the socket & net
namespace lists. We'll also need to take a reference to keys, held over
non-atomic contexts, so we need a refcount on keys also.
This change adds a validity flag (currently always true) and refcount to
struct mctp_sk_key. With a refcount on the keys, using RCU no longer
makes much sense; we have exact indications on the lifetime of keys. So,
we also change the RCU list traversal to a locked implementation.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may need to receive packets addressed to the null EID (==0), but
addressed to us at the physical layer.
This change adds a lookup for local routes when we see a packet
addressed to EID 0, and a local phys address.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allowing TUN is useful for testing, to route packets to userspace or to
tunnel between machines.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously with CONFIG_QRTR=m a separate ns.ko would be built which
wasn't done on purpose and should be included in qrtr.ko.
Rename qrtr.c to af_qrtr.c so we can build a qrtr.ko with both af_qrtr.c
and ns.c.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20210928171156.6353-1-luca@z3ntu.xyz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fib_notifier.c hasn't use any macro or function declared
in net/netns/ipv4.h.
Thus, these files can be removed from fib_notifier.c safely
without affecting the compilation of the net/ipv4 module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Link: https://lore.kernel.org/r/20210928164011.1454-1-liumh1@shanghaitech.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sequence count bridge_mcast_querier::seq is protected by
net_bridge::multicast_lock but seqcount_init() does not associate the
seqcount with the lock. This leads to a warning on PREEMPT_RT because
preemption is still enabled.
Let seqcount_init() associate the seqcount with lock that protects the
write section. Remove lockdep_assert_held_once() because lockdep already checks
whether the associated lock is held.
Fixes: 67b746f94f ("net: bridge: mcast: make sure querier port/address updates are consistent")
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210928141049.593833-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existence of the experimental feature identifiy is the indication
that it is supported or not. No extra flag needed and the initial flag
should define if a feature is enabled or not. This is actually defined
in the management API definition.
Fixes: ad93315183 ("Bluetooth: Add offload feature under experimental flag")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The existence of the experimental feature identifiy is the indication
that it is supported or not. No extra flag needed and the initial flag
should define if a feature is enabled or not. This is actually defined
in the management API definition.
Fixes: ae7d925b5c ("Bluetooth: Support the quality report events")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf 2021-09-28
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 14 day(s) which contain
a total of 11 files changed, 139 insertions(+), 53 deletions(-).
The main changes are:
1) Fix MIPS JIT jump code emission for too large offsets, from Piotr Krysiuk.
2) Fix x86 JIT atomic/fetch emission when dst reg maps to rax, from Johan Almbladh.
3) Fix cgroup_sk_alloc corner case when called from interrupt, from Daniel Borkmann.
4) Fix segfault in libbpf's linker for objects without BTF, from Kumar Kartikeya Dwivedi.
5) Fix bpf_jit_charge_modmem for applications with CAP_BPF, from Lorenz Bauer.
6) Fix return value handling for struct_ops BPF programs, from Hou Tao.
7) Various fixes to BPF selftests, from Jiri Benc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
,
The IV of CCM mode has special requirements, this patch supports CCM
mode of SM4 algorithm.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_create1() returns NULL on error, and the callers assume that it never
fails for reasons other than out of memory. So, the callers always return
-ENOMEM when unix_create1() fails.
However, it also returns NULL when the number of af_unix sockets exceeds
twice the limit controlled by sysctl: fs.file-max. In this case, the
callers should return -ENFILE like alloc_empty_file().
This patch changes unix_create1() to return the correct error value instead
of NULL on error.
Out of curiosity, the assumption has been wrong since 1999 due to this
change introduced in 2.2.4 [0].
diff -u --recursive --new-file v2.2.3/linux/net/unix/af_unix.c linux/net/unix/af_unix.c
--- v2.2.3/linux/net/unix/af_unix.c Tue Jan 19 11:32:53 1999
+++ linux/net/unix/af_unix.c Sun Mar 21 07:22:00 1999
@@ -388,6 +413,9 @@
{
struct sock *sk;
+ if (atomic_read(&unix_nr_socks) >= 2*max_files)
+ return NULL;
+
MOD_INC_USE_COUNT;
sk = sk_alloc(PF_UNIX, GFP_KERNEL, 1);
if (!sk) {
[0]: https://cdn.kernel.org/pub/linux/kernel/v2.2/patch-2.2.4.gz
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure multiple BSSID and enhanced multi-BSSID advertisement (EMA)
parameters in mac80211 for AP mode.
For each interface, 'mbssid_tx_vif' points to the transmitting interface of
the MBSSID set. The pointer is set to NULL if MBSSID is disabled.
Function ieee80211_stop() is modified to always bring down all the
non-transmitting interfaces first and the transmitting interface last.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20210916025437.29138-3-alokad@codeaurora.org
[slightly change logic to be more obvious]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
up->corkflag field can be read or written without any lock.
Annotate accesses to avoid possible syzbot/KCSAN reports.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kbuild supports <modname>-y as well as <modname>-objs.
This simplifies the Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign the objects directly to obj-$(CONFIG_INET).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deactivate old rule first, then append the new rule, so rule replacement
notification via netlink first reports the deletion of the old rule with
handle X in first place, then it adds the new rule (reusing the handle X
of the replaced old rule).
Note that the abort path releases the transaction that has been created
by nft_delrule() on error.
Fixes: ca08987885 ("netfilter: nf_tables: deactivate expressions in rule replecement routine")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add position handle to allow to identify the rule location from netlink
events. Otherwise, userspace cannot incrementally update a userspace
cache through monitoring events.
Skip handle dump if the rule has been either inserted (at the beginning
of the ruleset) or appended (at the end of the ruleset), the
NLM_F_APPEND netlink flag is sufficient in these two cases.
Handle NLM_F_REPLACE as NLM_F_APPEND since the rule replacement
expansion appends it after the specified rule handle.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a revert of
7b1957b049 ("netfilter: nf_defrag_ipv4: use net_generic infra")
and a partial revert of
8b0adbe3e3 ("netfilter: nf_defrag_ipv6: use net_generic infra").
If conntrack is builtin and kernel is booted with:
nf_conntrack.enable_hooks=1
.... kernel will fail to boot due to a NULL deref in
nf_defrag_ipv4_enable(): Its called before the ipv4 defrag initcall is
made, so net_generic() returns NULL.
To resolve this, move the user refcount back to struct net so calls
to those functions are possible even before their initcalls have run.
Fixes: 7b1957b049 ("netfilter: nf_defrag_ipv4: use net_generic infra")
Fixes: 8b0adbe3e3 ("netfilter: nf_defrag_ipv6: use net_generic infra").
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The returned opcode of command status of remove_adv is
wrong when LL privacy is enabled.
Signed-off-by: Yun-Hao Chung <howardchung@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During system suspend, advertisement monitoring is disabled by setting
the HCI_VS_MSFT_LE_Set_Advertisement_Filter_Enable to False. This
disables the monitoring during suspend, however, if the controller is
monitoring a device, it sends HCI_VS_MSFT_LE_Monitor_Device_Event to
indicate that the monitoring has been stopped for that particular
device. This event may occur after suspend depending on the
low_threshold_timeout and peer device advertisement frequency, which
causes early wake up.
Right way to disable the monitoring for suspend is by removing all the
monitors before suspend and re-monitor after resume to ensure no events
are received during suspend. This patch fixes this suspend/resume issue.
Following tests are performed:
- Add monitors before suspend and make sure DeviceFound gets triggered
- Suspend the system and verify that all monitors are removed by kernel
but not Released by bluetoothd
- Wake up and verify that all monitors are added again and DeviceFound
gets triggered
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Archie Pusaka <apusaka@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Optimize for the aligned case by precomputing the parameter values of
the xdp_buff_xsk and xdp_buff structures in the heads array. We can do
this as the heads array size is equal to the number of chunks in the
umem for the aligned case. Then every entry in this array will reflect
a certain chunk/frame and can therefore be prepopulated with the
correct values and we can drop the use of the free_heads stack. Note
that it is not possible to allocate more buffers than what has been
allocated in the aligned case since each chunk can only contain a
single buffer.
We can unfortunately not do this in the unaligned case as one chunk
might contain multiple buffers. In this case, we keep the old scheme
of populating a heads entry every time it is used and using
the free_heads stack.
Also move xp_release() and xp_get_handle() to xsk_buff_pool.h. They
were for some reason in xsk.c even though they are buffer pool
operations.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-7-magnus.karlsson@gmail.com
Add a new driver interface xsk_buff_alloc_batch() offering batched
buffer allocations to improve performance. The new interface takes
three arguments: the buffer pool to allocated from, a pointer to an
array of struct xdp_buff pointers which will contain pointers to the
allocated xdp_buffs, and an unsigned integer specifying the max number
of buffers to allocate. The return value is the actual number of
buffers that the allocator managed to allocate and it will be in the
range 0 <= N <= max, where max is the third parameter to the function.
u32 xsk_buff_alloc_batch(struct xsk_buff_pool *pool, struct xdp_buff **xdp,
u32 max);
A second driver interface is also introduced that need to be used in
conjunction with xsk_buff_alloc_batch(). It is a helper that sets the
size of struct xdp_buff and is used by the NIC Rx irq routine when
receiving a packet. This helper sets the three struct members data,
data_meta, and data_end. The two first ones is in the xsk_buff_alloc()
case set in the allocation routine and data_end is set when a packet
is received in the receive irq function. This unfortunately leads to
worse performance since the xdp_buff is touched twice with a long time
period in between leading to an extra cache miss. Instead, we fill out
the xdp_buff with all 3 fields at one single point in time in the
driver, when the size of the packet is known. Hence this helper. Note
that the driver has to use this helper (or set all three fields
itself) when using xsk_buff_alloc_batch(). xsk_buff_alloc() works as
before and does not require this.
void xsk_buff_set_size(struct xdp_buff *xdp, u32 size);
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-3-magnus.karlsson@gmail.com
This change prevents from users to access device before devlink
is fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core code notified users about add/remove objects without
relation if this object can be accessible or not. In this patch we unify
such user visible notifications in one place.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new attributes to configure support for multiple BSSID
and advanced multi-BSSID advertisements (EMA) in AP mode.
- NL80211_ATTR_MBSSID_CONFIG used for per interface configuration.
- NL80211_ATTR_MBSSID_ELEMS used to MBSSID elements for beacons.
Memory for the elements is allocated dynamically. This change frees
the memory in existing functions which call nl80211_parse_beacon(),
a comment is added to indicate the new references to do the same.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20210916025437.29138-2-alokad@codeaurora.org
[don't leave ERR_PTR hanging around]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* potential use-after-free in CCMP/GCMP RX processing
* potential use-after-free in TX A-MSDU processing
* revert to low data rates for no-ack as the commit
broke other things
* limit VHT MCS/NSS in radiotap injection
* drop frames with invalid addresses in IBSS mode
* check rhashtable_init() return value in mesh
* fix potentially unaligned access in mesh
* fix late beacon hrtimer handling in hwsim (syzbot)
* fix documentation for PTK0 rekeying
-----BEGIN PGP SIGNATURE-----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=hQAp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2021-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes berg says:
====================
Some fixes:
* potential use-after-free in CCMP/GCMP RX processing
* potential use-after-free in TX A-MSDU processing
* revert to low data rates for no-ack as the commit
broke other things
* limit VHT MCS/NSS in radiotap injection
* drop frames with invalid addresses in IBSS mode
* check rhashtable_init() return value in mesh
* fix potentially unaligned access in mesh
* fix late beacon hrtimer handling in hwsim (syzbot)
* fix documentation for PTK0 rekeying
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_nv.c hasn't use any macro or function declared in mm.h. Thus, these files
can be removed from tcp_nv.c safely without affecting the compilation
of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the (somewhat unlikely) event that we allocate a wiphy, then
add a regdomain to it, and then fail registration, we leak the
regdomain. Fix this by just always freeing it at the end, in the
normal cases we'll free (and NULL) it during wiphy_unregister().
This happened when the wiphy settings were bad, and since they
can be controlled by userspace with hwsim, syzbot was able to
find this issue.
Reported-by: syzbot+1638e7c770eef6b6c0d0@syzkaller.appspotmail.com
Fixes: 3e0c3ff36c ("cfg80211: allow multiple driver regulatory_hints()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20210927131105.68b70cef4674.I4b9f0aa08c2af28555963b9fe3d34395bb72e0cc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is to save the transmit power envelope element and power
constraint in struct ieee80211_bss_conf for 6 GHz. Lower driver
will use this info to calculate the power limit.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-7-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 3765996e4f ("napi: fix race inside napi_enable") fixed
an ordering bug in napi_enable() and made the napi_enable() diverge
from napi_disable(). The state transitions done on disable are
not symmetric to enable.
There is no known bug in napi_disable() this is just refactoring.
Eric suggests we can also replace msleep(1) with a more opportunistic
usleep_range().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to convert the regulatory info subfield in HE operation
element to power type and save in struct cfg80211_chan_def.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-3-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're pointing into a frame, the pointer to the
twt_agrt->req_type struct member is potentially not
aligned properly. Open-code le16p_replace_bits() to
avoid passing an unaligned pointer.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: f5a4c24e68 ("mac80211: introduce individual TWT support in AP mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20210927115124.e1208694f37b.Ie3de9bcc5dde5a79e3ac81f3185beafe4d214e57@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a driver FILS crypto offload extended capability flag to indicate
that the driver running in AP mode is capable of handling encryption
and decryption of (Re)Association request and response frames.
Add a command to set FILS AAD data to driver.
This feature is supported on drivers running in AP mode only.
This extended capability is exchanged with hostapd during cfg80211
init. If the driver indicates this capability, then before sending the
Authentication response frame, hostapd sets FILS AAD data to the
driver. This allows the driver to decrypt (Re)Association Request
frame and encrypt (Re)Association Response frame. FILS Key derivation
will still be done in hostapd.
Signed-off-by: Subrat Mishra <subratm@codeaurora.org>
Link: https://lore.kernel.org/r/1631685143-13530-1-git-send-email-subratm@codeaurora.org
[fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Link: https://lore.kernel.org/r/20210927033457.1020967-4-shjy180909@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When PN checking is done in mac80211, for fragmentation we need
to copy the PN to the RX struct so we can later use it to do a
comparison, since commit bf30ca922a ("mac80211: check defrag
PN against current frame").
Unfortunately, in that commit I used the 'hdr' variable without
it being necessarily valid, so use-after-free could occur if it
was necessary to reallocate (parts of) the frame.
Fix this by reloading the variable after the code that results
in the reallocations, if any.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=214401.
Cc: stable@vger.kernel.org
Fixes: bf30ca922a ("mac80211: check defrag PN against current frame")
Link: https://lore.kernel.org/r/20210927115838.12b9ac6bb233.I1d066acd5408a662c3b6e828122cd314fcb28cdb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We observed below report when playing with netlink sock:
UBSAN: shift-out-of-bounds in net/sched/sch_api.c:580:10
shift exponent 249 is too large for 32-bit type
CPU: 0 PID: 685 Comm: a.out Not tainted
Call Trace:
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x4e
__ubsan_handle_shift_out_of_bounds+0x161/0x182
__qdisc_calculate_pkt_len+0xf0/0x190
__dev_queue_xmit+0x2ed/0x15b0
it seems like kernel won't check the stab log value passing from
user, and will use the insane value later to calculate pkt_len.
This patch just add a check on the size/cell_log to avoid insane
calculation.
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The retransmit head will be NULL in case there is no in-flight data
(meaning all data injected into network has been acked).
In that case the retransmit timer is stopped.
This is only correct if there is no more pending, not-yet-sent data.
If there is, the retransmit timer needs to set the PENDING bit again so
that mptcp tries to send the remaining (new) data once a subflow can accept
more data.
Also, mptcp_subflow_get_retrans() has to be called unconditionally.
This function checks for subflows that have become unresponsive and marks
them as stale, so in the case where the rtx queue is empty, subflows
will never be marked stale which prevents available backup subflows from
becoming eligible for transmit.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/226
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The update on recovery is not correct.
msk->tx_pending_data += msk->snd_nxt - rtx_head->data_seq;
will update tx_pending_data multiple times when a subflow is declared
stale while earlier recovery is still in progress.
This means that tx_pending_data will still be positive even after
all data as has been transmitted.
Rather than fix it, remove this field: there are no consumers.
The outstanding data byte count can be computed either via
"msk->write_seq - rtx_head->data_seq" or
"msk->write_seq - msk->snd_una".
The latter is more recent/accurate estimate as rtx_head adjustment
is deferred until mptcp lock can be acquired.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a few more places where the mptcp code duplicates
lockdep_assert_held_once(). Let's use the existing macro and
avoid a bunch of compiler's conditional.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since OPTIONS_MPTCP_MPC has been defined, use it instead of open-coding.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When recovering after a link failure, snd_nxt should not be set to a
lower value. Else, update of snd_nxt is broken because:
msk->snd_nxt += ret; (where ret is number of bytes sent)
assumes that snd_nxt always moves forward.
After reduction, its possible that snd_nxt update gets out of sync:
dfrag we just sent might have had a data sequence number even past
recovery_snd_nxt.
This change factors the common msk state update to a helper
and updates snd_nxt based on the current dfrag data sequence number.
The conditional is required for the recovery phase where we may
re-transmit old dfrags that are before current snd_nxt.
After this change, snd_nxt only moves forward and covers all in-sequence
data that was transmitted.
recovery_snd_nxt is retained to detect when recovery has completed.
Fixes: 1e1d9d6f11 ("mptcp: handle pending data on closed subflow")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
1) ipset limits the max allocatable memory via kvmalloc() to MAX_INT,
from Jozsef Kadlecsik.
2) Check ip_vs_conn_tab_bits value to be in the range specified
in Kconfig, from Andrea Claudi.
3) Initialize fragment offset in ip6tables, from Jeremy Sowden.
4) Make conntrack hash chain length random, from Florian Westphal.
5) Add zone ID to conntrack and NAT hashtuple again, also from Florian.
6) Add selftests for bidirectional zone support and colliding tuples,
from Florian Westphal.
7) Unlink table before synchronize_rcu when cleaning tables with
owner, from Florian.
8) ipset limits the max allocatable memory via kvmalloc() to MAX_INT.
9) Release conntrack entries via workqueue in masquerade, from Florian.
10) Fix bogus net_init in iptables raw table definition, also from Florian.
11) Work around missing softdep in log extensions, from Florian Westphal.
12) Serialize hash resizes and cleanups with mutex, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: conntrack: serialize hash resizes and cleanups
netfilter: log: work around missing softdep backend module
netfilter: iptable_raw: drop bogus net_init annotation
netfilter: nf_nat_masquerade: defer conntrack walk to work queue
netfilter: nf_nat_masquerade: make async masq_inet6_event handling generic
netfilter: nf_tables: Fix oversized kvmalloc() calls
netfilter: nf_tables: unlink table before deleting it
selftests: netfilter: add zone stress test with colliding tuples
selftests: netfilter: add selftest for directional zone support
netfilter: nat: include zone id in nat table hash again
netfilter: conntrack: include zone id in tuple hash again
netfilter: conntrack: make max chain length random
netfilter: ip6_tables: zero-initialize fragment offset
ipvs: check that ip_vs_conn_tab_bits is between 8 and 20
netfilter: ipset: Fix oversized kvmalloc() calls
====================
Link: https://lore.kernel.org/r/20210924221113.348767-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Directly using _usecs_to_jiffies() might be unsafe, so it's
better to use usecs_to_jiffies() instead.
Because we can see that the result of _usecs_to_jiffies()
could be larger than MAX_JIFFY_OFFSET values without the
check of the input.
Fixes: c410bf0193 ("Fix the excessive initial retransmission timeout")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to track CE marks per rate sample (one round trip), TCP needs a
per-skb header field to record the tp->delivered_ce count when the skb
was sent. To make space, we replace the "last_in_flight" field which is
used exclusively for NV congestion control. The stat needed by NV can be
alternatively approximated by existing stats tcp_sock delivered and
mss_cache.
This patch counts the number of packets delivered which have CE marks in
the rate sample, using similar approach of delivery accounting.
Cc: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need in extra one line functions to call relevant
functions only once.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no in-kernel users for the devlink port parameters API,
so let's remove it.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multipath RTA_FLOW is embedded in nexthop. Dump it in fib_add_nexthop()
to get the length of rtnexthop correct.
Fixes: b0f6019363 ("ipv4: Refactor nexthop attributes in fib_dump_info")
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function ieee80211_prep_channel(), it has some ieee80211_bss_get_ie()
and cfg80211_find_ext_ie() to get the IE, this is to use another
function ieee802_11_parse_elems() to get all the IEs in one time.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-6-wgong@codeaurora.org
[remove now unnecessary size validation, use -ENOMEM, free elems earlier
for less error handling code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
current Linux refuses to change the 'backup' bit of MPTCP endpoints, i.e.
using MPTCP_PM_CMD_SET_FLAGS, unless it finds (at least) one subflow that
matches the endpoint address. There is no reason for that, so we can just
ignore the return value of mptcp_nl_addr_backup(). In this way, endpoints
can reconfigure their 'backup' flag even if no MPTCP sockets are open (or
more generally, in case the MP_PRIO message is not sent out).
Fixes: 0f9f696a50 ("mptcp: add set_flags command in PM netlink")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_token_get_sock() may return a mptcp socket that is in
a different net namespace than the socket that received the token value.
The mptcp syncookie code path had an explicit check for this,
this moves the test into mptcp_token_get_sock() function.
Eventually token.c should be converted to pernet storage, but
such change is not suitable for net tree.
Fixes: 2c5ebd001d ("mptcp: refactor token container")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should always check if skb_header_pointer's return is NULL before
using it, otherwise it may cause null-ptr-deref, as syzbot reported:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:sctp_rcv_ootb net/sctp/input.c:705 [inline]
RIP: 0010:sctp_rcv+0x1d84/0x3220 net/sctp/input.c:196
Call Trace:
<IRQ>
sctp6_rcv+0x38/0x60 net/sctp/ipv6.c:1109
ip6_protocol_deliver_rcu+0x2e9/0x1ca0 net/ipv6/ip6_input.c:422
ip6_input_finish+0x62/0x170 net/ipv6/ip6_input.c:463
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip6_input+0x9c/0xd0 net/ipv6/ip6_input.c:472
dst_input include/net/dst.h:460 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:76 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ipv6_rcv+0x28c/0x3c0 net/ipv6/ip6_input.c:297
Fixes: 3acb50c18d ("sctp: delay as much as possible skb_linearize")
Reported-by: syzbot+581aff2ae6b860625116@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As the 802.11 spec evolves, we need to parse more and more
elements. This is causing the struct to grow, and we can no
longer get away with putting it on the stack.
Change the API to always dynamically allocate and return an
allocated pointer that must be kfree()d later.
As an alternative, I contemplated a scheme whereby we'd say
in the code which elements we needed, e.g.
DECLARE_ELEMENT_PARSER(elems,
SUPPORTED_CHANNELS,
CHANNEL_SWITCH,
EXT(KEY_DELIVERY));
ieee802_11_parse_elems(..., &elems, ...);
and while I think this is possible and will save us a lot
since most individual places only care about a small subset
of the elements, it ended up being a bit more work since a
lot of places do the parsing and then pass the struct to
other functions, sometimes with multiple levels.
Link: https://lore.kernel.org/r/20210920154009.26caff6b5998.I05ae58768e990e611aee8eca8abefd9d7bc15e05@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently pass the entire elements to the rx_bcn_presp()
method, but only need mesh_config. Additionally, we use the
length of the elements to calculate back the entire frame's
length, but that's confusing - just pass the length of the
frame instead.
Link: https://lore.kernel.org/r/20210920154009.a18ed3d2da6c.I1824b773a0fbae4453e1433c184678ca14e8df45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts the following patches :
- commit 2e05fcae83 ("tcp: fix compile error if !CONFIG_SYSCTL")
- commit 4f661542a4 ("tcp: fix zerocopy and notsent_lowat issues")
- commit 472c2e07ee ("tcp: add one skb cache for tx")
- commit 8b27dae5a2 ("tcp: add one skb cache for rx")
Having a cache of one skb (in each direction) per TCP socket is fragile,
since it can cause a significant increase of memory needs,
and not good enough for high speed flows anyway where more than one skb
is needed.
We want instead to add a generic infrastructure, with more flexible
per-cpu caches, for alien NUMA nodes.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch the mentioned helper is
used only inside its compilation unit: let's make
it static.
RFC -> v1:
- preserve the tcp_build_frag() helper (Eric)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to revert the skb TX cache, but MPTCP is currently
using it unconditionally.
Rework the MPTCP tx code, so that tcp_tx_skb_cache is not
needed anymore: do the whole coalescing check, skb allocation
skb initialization/update inside mptcp_sendmsg_frag(), quite
alike the current TCP code.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the tcp_skb_entail() helper is actually skb_entail(), renamed
to provide proper scope.
The two helper will be used by the next patch.
RFC -> v1:
- rename skb_entail to tcp_skb_entail (Eric)
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08 ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() functions.
Also, take the opportunity to refactor the memcpy() call to use the
flex_array_size() helper.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210919114040.41522-1-len.baker@gmx.com
[remove unnecessary variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzkaller discovered memory leaks [1] that can be reduced to the
following commands:
# ip nexthop add id 1 blackhole
# devlink dev reload pci/0000:06:00.0
As part of the reload flow, mlxsw will unregister its netdevs and then
unregister from the nexthop notification chain. Before unregistering
from the notification chain, mlxsw will receive delete notifications for
nexthop objects using netdevs registered by mlxsw or their uppers. mlxsw
will not receive notifications for nexthops using netdevs that are not
dismantled as part of the reload flow. For example, the blackhole
nexthop above that internally uses the loopback netdev as its nexthop
device.
One way to fix this problem is to have listeners flush their nexthop
tables after unregistering from the notification chain. This is
error-prone as evident by this patch and also not symmetric with the
registration path where a listener receives a dump of all the existing
nexthops.
Therefore, fix this problem by replaying delete notifications for the
listener being unregistered. This is symmetric to the registration path
and also consistent with the netdev notification chain.
The above means that unregister_nexthop_notifier(), like
register_nexthop_notifier(), will have to take RTNL in order to iterate
over the existing nexthops and that any callers of the function cannot
hold RTNL. This is true for mlxsw and netdevsim, but not for the VXLAN
driver. To avoid a deadlock, change the latter to unregister its nexthop
listener without holding RTNL, making it symmetric to the registration
path.
[1]
unreferenced object 0xffff88806173d600 (size 512):
comm "syz-executor.0", pid 1290, jiffies 4295583142 (age 143.507s)
hex dump (first 32 bytes):
41 9d 1e 60 80 88 ff ff 08 d6 73 61 80 88 ff ff A..`......sa....
08 d6 73 61 80 88 ff ff 01 00 00 00 00 00 00 00 ..sa............
backtrace:
[<ffffffff81a6b576>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
[<ffffffff81a6b576>] slab_post_alloc_hook+0x96/0x490 mm/slab.h:522
[<ffffffff81a716d3>] slab_alloc_node mm/slub.c:3206 [inline]
[<ffffffff81a716d3>] slab_alloc mm/slub.c:3214 [inline]
[<ffffffff81a716d3>] kmem_cache_alloc_trace+0x163/0x370 mm/slub.c:3231
[<ffffffff82e8681a>] kmalloc include/linux/slab.h:591 [inline]
[<ffffffff82e8681a>] kzalloc include/linux/slab.h:721 [inline]
[<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_group_create drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4918 [inline]
[<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_new drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5054 [inline]
[<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_event+0x59a/0x2910 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5239
[<ffffffff813ef67d>] notifier_call_chain+0xbd/0x210 kernel/notifier.c:83
[<ffffffff813f0662>] blocking_notifier_call_chain kernel/notifier.c:318 [inline]
[<ffffffff813f0662>] blocking_notifier_call_chain+0x72/0xa0 kernel/notifier.c:306
[<ffffffff8384b9c6>] call_nexthop_notifiers+0x156/0x310 net/ipv4/nexthop.c:244
[<ffffffff83852bd8>] insert_nexthop net/ipv4/nexthop.c:2336 [inline]
[<ffffffff83852bd8>] nexthop_add net/ipv4/nexthop.c:2644 [inline]
[<ffffffff83852bd8>] rtm_new_nexthop+0x14e8/0x4d10 net/ipv4/nexthop.c:2913
[<ffffffff833e9a78>] rtnetlink_rcv_msg+0x448/0xbf0 net/core/rtnetlink.c:5572
[<ffffffff83608703>] netlink_rcv_skb+0x173/0x480 net/netlink/af_netlink.c:2504
[<ffffffff833de032>] rtnetlink_rcv+0x22/0x30 net/core/rtnetlink.c:5590
[<ffffffff836069de>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
[<ffffffff836069de>] netlink_unicast+0x5ae/0x7f0 net/netlink/af_netlink.c:1340
[<ffffffff83607501>] netlink_sendmsg+0x8e1/0xe30 net/netlink/af_netlink.c:1929
[<ffffffff832fde84>] sock_sendmsg_nosec net/socket.c:704 [inline]
[<ffffffff832fde84>] sock_sendmsg net/socket.c:724 [inline]
[<ffffffff832fde84>] ____sys_sendmsg+0x874/0x9f0 net/socket.c:2409
[<ffffffff83304a44>] ___sys_sendmsg+0x104/0x170 net/socket.c:2463
[<ffffffff83304c01>] __sys_sendmsg+0x111/0x1f0 net/socket.c:2492
[<ffffffff83304d5d>] __do_sys_sendmsg net/socket.c:2501 [inline]
[<ffffffff83304d5d>] __se_sys_sendmsg net/socket.c:2499 [inline]
[<ffffffff83304d5d>] __x64_sys_sendmsg+0x7d/0xc0 net/socket.c:2499
Fixes: 2a014b200b ("mlxsw: spectrum_router: Add support for nexthop objects")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: CPU: 1 PID: 9 at net/mac80211/sta_info.c:554
sta_info_insert_rcu+0x121/0x12a0
Modules linked in:
CPU: 1 PID: 9 Comm: kworker/u8:1 Not tainted 5.14.0-rc7+ #253
Workqueue: phy3 ieee80211_iface_work
RIP: 0010:sta_info_insert_rcu+0x121/0x12a0
...
Call Trace:
ieee80211_ibss_finish_sta+0xbc/0x170
ieee80211_ibss_work+0x13f/0x7d0
ieee80211_iface_work+0x37a/0x500
process_one_work+0x357/0x850
worker_thread+0x41/0x4d0
If an Ad-Hoc node receives packets with invalid source MAC address,
it hits a WARN_ON in sta_info_insert_check(), this can spam the log.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210827144230.39944-1-yuehaibing@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_amsdu_aggregate() set a pointer frag_tail point to the
end of skb_shinfo(head)->frag_list, and use it to bind other skb in
the end of this function. But when execute ieee80211_amsdu_aggregate()
->ieee80211_amsdu_realloc_pad()->pskb_expand_head(), the address of
skb_shinfo(head)->frag_list will be changed. However, the
ieee80211_amsdu_aggregate() not update frag_tail after call
pskb_expand_head(). That will cause the second skb can't bind to the
head skb appropriately.So we update the address of frag_tail to fix it.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210830073240.12736-1-pkshih@realtek.com
[reword comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit d333322361 ("mac80211: do not use low data rates for
data frames with no ack flag").
Returning false early in rate_control_send_low breaks sending broadcast
packets, since rate control will not select a rate for it.
Before re-introducing a fixed version of this patch, we should probably also
make some changes to rate control to be more conservative in selecting rates
for no-ack packets and also prevent using probing rates on them, since we won't
get any feedback.
Fixes: d333322361 ("mac80211: do not use low data rates for data frames with no ack flag")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210906083559.9109-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As stated in the comment above xfrm_nlmsg_multicast(), rcu read lock must
be held before calling this function.
Reported-by: syzbot+3d9866419b4aa8f985d6@syzkaller.appspotmail.com
Fixes: 703b94b93c19 ("xfrm: notify default policy on update")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This moves hci_debugfs_create_basic to hci_debugfs.c which is where all
the others debugfs entries are handled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid to call ksize again in __build_skb_around by passing
the result of data ksize to __build_skb_around
nginx stress test shows this change can reduce ksize cpu usage,
and give a little performance boost
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_net_ipv4.c hasn't use any macro or function declared in igmp.h,
inetdevice.h, mm.h, module.h, nsproxy.h, swap.h, inet_frag.h, route.h
and snmp.h. Thus, these files can be removed from sysctl_net_ipv4.c
safely without affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the blamed commit, dsa_tree_teardown_switches() was split into two
smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports.
However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports.
Fixes: a57d8c217a ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes: b286a0651e ("net/smc: handle incoming CDC validation message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syncookies.c hasn't use any macro or function declared in slab.h and random.h,
Thus, these files can be removed from syncookies.c safely without
affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_tunnel_core.c hasn't use any macro or function declared in udp.h, types.h,
and net_namespace.h. Thus, these files can be removed from udp_tunnel_core.c
safely without affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb in modified by hci_send_sco which pushes SCO headers thus
changing skb->len causing sco_sock_sendmsg to fail.
Fixes: 0771cbb3b9 ("Bluetooth: SCO: Replace use of memcpy_from_msg with bt_skb_sendmsg")
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Passing NULL to PTR_ERR will result in 0 (success), also since the likes of
bt_skb_sendmsg does never return NULL it is safe to replace the instances of
IS_ERR_OR_NULL with IS_ERR when checking its return.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for BT_{SND,RCV}BUF so userspace can set MTU based on
the channel usage.
Fixes: https://github.com/bluez/bluez/issues/201
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves functions manipulating EIR/Adv Data to its own file so it
can be reused by other files.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot was able to trigger the following warning [1]
No repro found by syzbot yet but I was able to trigger similar issue
by having 2 scripts running in parallel, changing conntrack hash sizes,
and:
for j in `seq 1 1000` ; do unshare -n /bin/true >/dev/null ; done
It would take more than 5 minutes for net_namespace structures
to be cleaned up.
This is because nf_ct_iterate_cleanup() has to restart everytime
a resize happened.
By adding a mutex, we can serialize hash resizes and cleanups
and also make get_next_corpse() faster by skipping over empty
buckets.
Even without resizes in the picture, this patch considerably
speeds up network namespace dismantles.
[1]
INFO: task syz-executor.0:8312 can't die for more than 144 seconds.
task:syz-executor.0 state:R running task stack:25672 pid: 8312 ppid: 6573 flags:0x00004006
Call Trace:
context_switch kernel/sched/core.c:4955 [inline]
__schedule+0x940/0x26f0 kernel/sched/core.c:6236
preempt_schedule_common+0x45/0xc0 kernel/sched/core.c:6408
preempt_schedule_thunk+0x16/0x18 arch/x86/entry/thunk_64.S:35
__local_bh_enable_ip+0x109/0x120 kernel/softirq.c:390
local_bh_enable include/linux/bottom_half.h:32 [inline]
get_next_corpse net/netfilter/nf_conntrack_core.c:2252 [inline]
nf_ct_iterate_cleanup+0x15a/0x450 net/netfilter/nf_conntrack_core.c:2275
nf_conntrack_cleanup_net_list+0x14c/0x4f0 net/netfilter/nf_conntrack_core.c:2469
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:171
setup_net+0x639/0xa30 net/core/net_namespace.c:349
copy_net_ns+0x319/0x760 net/core/net_namespace.c:470
create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:226
ksys_unshare+0x445/0x920 kernel/fork.c:3128
__do_sys_unshare kernel/fork.c:3202 [inline]
__se_sys_unshare kernel/fork.c:3200 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3200
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f63da68e739
RSP: 002b:00007f63d7c05188 EFLAGS: 00000246 ORIG_RAX: 0000000000000110
RAX: ffffffffffffffda RBX: 00007f63da792f80 RCX: 00007f63da68e739
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000040000000
RBP: 00007f63da6e8cc4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f63da792f80
R13: 00007fff50b75d3f R14: 00007f63d7c05300 R15: 0000000000022000
Showing all locks held in the system:
1 lock held by khungtaskd/27:
#0: ffffffff8b980020 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260 kernel/locking/lockdep.c:6446
2 locks held by kworker/u4:2/153:
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic64_set arch/x86/include/asm/atomic64_64.h:34 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic_long_set include/linux/atomic/atomic-long.h:41 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: atomic_long_set include/linux/atomic/atomic-instrumented.h:1198 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_data kernel/workqueue.c:634 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_pool_and_clear_pending kernel/workqueue.c:661 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x896/0x1690 kernel/workqueue.c:2268
#1: ffffc9000140fdb0 ((kfence_timer).work){+.+.}-{0:0}, at: process_one_work+0x8ca/0x1690 kernel/workqueue.c:2272
1 lock held by systemd-udevd/2970:
1 lock held by in:imklog/6258:
#0: ffff88807f970ff0 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0xe9/0x100 fs/file.c:990
3 locks held by kworker/1:6/8158:
1 lock held by syz-executor.0/8312:
2 locks held by kworker/u4:13/9320:
1 lock held by syz-executor.5/10178:
1 lock held by syz-executor.4/10217:
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
iptables/nftables has two types of log modules:
1. backend, e.g. nf_log_syslog, which implement the functionality
2. frontend, e.g. xt_LOG or nft_log, which call the functionality
provided by backend based on nf_tables or xtables rule set.
Problem is that the request_module() call to load the backed in
nf_logger_find_get() might happen with nftables transaction mutex held
in case the call path is via nf_tables/nft_compat.
This can cause deadlocks (see 'Fixes' tags for details).
The chosen solution as to let modprobe deal with this by adding 'pre: '
soft dep tag to xt_LOG (to load the syslog backend) and xt_NFLOG (to
load nflog backend).
Eric reports that this breaks on systems with older modprobe that
doesn't support softdeps.
Another, similar issue occurs when someone either insmods xt_(NF)LOG
directly or unloads the backend module (possible if no log frontend
is in use): because the frontend module is already loaded, modprobe is
not invoked again so the softdep isn't evaluated.
Add a workaround: If nf_logger_find_get() returns -ENOENT and call
is not via nft_compat, load the backend explicitly and try again.
Else, let nft_compat ask for deferred request_module via nf_tables
infra.
Softdeps are kept in-place, so with newer modprobe the dependencies
are resolved from userspace.
Fixes: cefa31a9d4 ("netfilter: nft_log: perform module load from nf_tables")
Fixes: a38b5b56d6 ("netfilter: nf_log: add module softdeps")
Reported-and-tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a leftover from the times when this function was wired up via
pernet_operations. Now its called when userspace asks for the table.
With CONFIG_NET_NS=n, iptable_raw_table_init memory has been discarded
already and we get a kernel crash.
Other tables are fine, __net_init annotation was removed already.
Fixes: fdacd57c79 ("netfilter: x_tables: never register tables by default")
Reported-by: youling 257 <youling257@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ipv4 and device notifiers are called with RTNL mutex held.
The table walk can take some time, better not block other RTNL users.
'ip a' has been reported to block for up to 20 seconds when conntrack table
has many entries and device down events are frequent (e.g., PPP).
Reported-and-tested-by: Martin Zaharinov <micron10@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
masq_inet6_event is called asynchronously from system work queue,
because the inet6 notifier is atomic and nf_iterate_cleanup can sleep.
The ipv4 and device notifiers call nf_iterate_cleanup directly.
This is legal, but these notifiers are called with RTNL mutex held.
A large conntrack table with many devices coming and going will have severe
impact on the system usability, with 'ip a' blocking for several seconds.
This change places the defer code into a helper and makes it more
generic so ipv4 and ifdown notifiers can be converted to defer the
cleanup walk as well in a follow patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
syzbot reports following UAF:
BUG: KASAN: use-after-free in memcmp+0x18f/0x1c0 lib/string.c:955
nla_strcmp+0xf2/0x130 lib/nlattr.c:836
nft_table_lookup.part.0+0x1a2/0x460 net/netfilter/nf_tables_api.c:570
nft_table_lookup net/netfilter/nf_tables_api.c:4064 [inline]
nf_tables_getset+0x1b3/0x860 net/netfilter/nf_tables_api.c:4064
nfnetlink_rcv_msg+0x659/0x13f0 net/netfilter/nfnetlink.c:285
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504
Problem is that all get operations are lockless, so the commit_mutex
held by nft_rcv_nl_event() isn't enough to stop a parallel GET request
from doing read-accesses to the table object even after synchronize_rcu().
To avoid this, unlink the table first and store the table objects in
on-stack scratch space.
Fixes: 6001a930ce ("netfilter: nftables: introduce table ownership")
Reported-and-tested-by: syzbot+f31660cf279b0557160c@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Similar to the conntrack change, also use the zone id for the nat source
lists if the zone id is valid in both directions.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
commit deedb59039 ("netfilter: nf_conntrack: add direction support for zones")
removed the zone id from the hash value.
This has implications on hash chain lengths with overlapping tuples, which
can hit 64k entries on released kernels, before upper droplimit was added
in d7e7747ac5 ("netfilter: refuse insertion if chain has grown too large").
With that change reverted, test script coming with this series shows
linear insertion time growth:
10000 entries in 3737 ms (now 10000 total, loop 1)
10000 entries in 16994 ms (now 20000 total, loop 2)
10000 entries in 47787 ms (now 30000 total, loop 3)
10000 entries in 72731 ms (now 40000 total, loop 4)
10000 entries in 95761 ms (now 50000 total, loop 5)
10000 entries in 96809 ms (now 60000 total, loop 6)
inserted 60000 entries from packet path in 333825 ms
With d7e7747ac5 in place, the test fails.
There are three supported zone use cases:
1. Connection is in the default zone (zone 0).
This means to special config (the default).
2. Connection is in a different zone (1 to 2**16).
This means rules are in place to put packets in
the desired zone, e.g. derived from vlan id or interface.
3. Original direction is in zone X and Reply is in zone 0.
3) allows to use of the existing NAT port collision avoidance to provide
connectivity to internet/wan even when the various zones have overlapping
source networks separated via policy routing.
In case the original zone is 0 all three cases are identical.
There is no way to place original direction in zone x and reply in
zone y (with y != 0).
Zones need to be assigned manually via the iptables/nftables ruleset,
before conntrack lookup occurs (raw table in iptables) using the
"CT" target conntrack template support
(-j CT --{zone,zone-orig,zone-reply} X).
Normally zone assignment happens based on incoming interface, but could
also be derived from packet mark, vlan id and so on.
This means that when case 3 is used, the ruleset will typically not even
assign a connection tracking template to the "reply" packets, so lookup
happens in zone 0.
However, it is possible that reply packets also match a ct zone
assignment rule which sets up a template for zone X (X > 0) in original
direction only.
Therefore, after making the zone id part of the hash, we need to do a
second lookup using the reply zone id if we did not find an entry on
the first lookup.
In practice, most deployments will either not use zones at all or the
origin and reply zones are the same, no second lookup is required in
either case.
After this change, packet path insertion test passes with constant
insertion times:
10000 entries in 1064 ms (now 10000 total, loop 1)
10000 entries in 1074 ms (now 20000 total, loop 2)
10000 entries in 1066 ms (now 30000 total, loop 3)
10000 entries in 1079 ms (now 40000 total, loop 4)
10000 entries in 1081 ms (now 50000 total, loop 5)
10000 entries in 1082 ms (now 60000 total, loop 6)
inserted 60000 entries from packet path in 6452 ms
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Similar to commit 67d6d681e1
("ipv4: make exception cache less predictible"):
Use a random drop length to make it harder to detect when entries were
hashed to same bucket list.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
tcp_minisocks.c hasn't use any macro or function declared in mm.h, module.h,
slab.h, sysctl.h, workqueue.h, static_key.h and inet_common.h. Thus, these
files can be removed from tcp_minisocks.c safely without affecting the
compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_fastopen.c hasn't use any macro or function declared in crypto.h, err.h,
init.h, list.h, rculist.h and inetpeer.h. Thus, these files can be removed
from tcp_fastopen.c safely without affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
route.c hasn't use any macro or function declared in uaccess.h, types.h,
string.h, sockios.h, times.h, protocol.h, arp.h and l3mdev.h. Thus, these
files can be removed from route.c safely without affecting the compilation
of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The resilient nexthop group torture tests in fib_nexthop.sh exposed a
possible division by zero while replacing a resilient group [1]. The
division by zero occurs when the data path sees a resilient nexthop
group with zero buckets.
The tests replace a resilient nexthop group in a loop while traffic is
forwarded through it. The tests do not specify the number of buckets
while performing the replacement, resulting in the kernel allocating a
stub resilient table (i.e, 'struct nh_res_table') with zero buckets.
This table should never be visible to the data path, but the old nexthop
group (i.e., 'oldg') might still be used by the data path when the stub
table is assigned to it.
Fix this by only assigning the stub table to the old nexthop group after
making sure the group is no longer used by the data path.
Tested with fib_nexthops.sh:
Tests passed: 222
Tests failed: 0
[1]
divide error: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 1850 Comm: ping Not tainted 5.14.0-custom-10271-ga86eb53057fe #1107
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:nexthop_select_path+0x2d2/0x1a80
[...]
Call Trace:
fib_select_multipath+0x79b/0x1530
fib_select_path+0x8fb/0x1c10
ip_route_output_key_hash_rcu+0x1198/0x2da0
ip_route_output_key_hash+0x190/0x340
ip_route_output_flow+0x21/0x120
raw_sendmsg+0x91d/0x2e10
inet_sendmsg+0x9e/0xe0
__sys_sendto+0x23d/0x360
__x64_sys_sendto+0xe1/0x1b0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Cc: stable@vger.kernel.org
Fixes: 283a72a559 ("nexthop: Add implementation of resilient next-hop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process will cause napi.state to contain NAPI_STATE_SCHED and
not in the poll_list, which will cause napi_disable() to get stuck.
The prefix "NAPI_STATE_" is removed in the figure below, and
NAPI_STATE_HASHED is ignored in napi.state.
CPU0 | CPU1 | napi.state
===============================================================================
napi_disable() | | SCHED | NPSVC
napi_enable() | |
{ | |
smp_mb__before_atomic(); | |
clear_bit(SCHED, &n->state); | | NPSVC
| napi_schedule_prep() | SCHED | NPSVC
| napi_poll() |
| napi_complete_done() |
| { |
| if (n->state & (NPSVC | | (1)
| _BUSY_POLL))) |
| return false; |
| ................ |
| } | SCHED | NPSVC
| |
clear_bit(NPSVC, &n->state); | | SCHED
} | |
| |
napi_schedule_prep() | | SCHED | MISSED (2)
(1) Here return direct. Because of NAPI_STATE_NPSVC exists.
(2) NAPI_STATE_SCHED exists. So not add napi.poll_list to sd->poll_list
Since NAPI_STATE_SCHED already exists and napi is not in the
sd->poll_list queue, NAPI_STATE_SCHED cannot be cleared and will always
exist.
1. This will cause this queue to no longer receive packets.
2. If you encounter napi_disable under the protection of rtnl_lock, it
will cause the entire rtnl_lock to be locked, affecting the overall
system.
This patch uses cmpxchg to implement napi_enable(), which ensures that
there will be no race due to the separation of clear two bits.
Fixes: 2d8bff1269 ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for handling active queue changes is identical
between mq and mqprio, reuse it.
Suggested-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f8b1c01a ("net: dsa: Do not make user port errors fatal")
decided it was fine to ignore errors on certain ports that fail to
probe, and go on with the ports that do probe fine.
Commit fb6ec87f72 ("net: dsa: Fix type was not set for devlink port")
noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get
called, and devlink notices after a timeout of 3600 seconds and prints a
WARN_ON. So it went ahead to unregister the devlink port. And because
there exists an UNUSED port flavour, we actually re-register the devlink
port as UNUSED.
Commit 08156ba430 ("net: dsa: Add devlink port regions support to
DSA") added devlink port regions, which are set up by the driver and not
by DSA.
When we trigger the devlink port deregistration and reregistration as
unused, devlink now prints another WARN_ON, from here:
devlink_port_unregister:
WARN_ON(!list_empty(&devlink_port->region_list));
So the port still has regions, which makes sense, because they were set
up by the driver, and the driver doesn't know we're unregistering the
devlink port.
Somebody needs to tear them down, and optionally (actually it would be
nice, to be consistent) set them up again for the new devlink port.
But DSA's layering stays in our way quite badly here.
The options I've considered are:
1. Introduce a function in devlink to just change a port's type and
flavour. No dice, devlink keeps a lot of state, it really wants the
port to not be registered when you set its parameters, so changing
anything can only be done by destroying what we currently have and
recreating it.
2. Make DSA cache the parameters passed to dsa_devlink_port_region_create,
and the region returned, keep those in a list, then when the devlink
port unregister needs to take place, the existing devlink regions are
destroyed by DSA, and we replay the creation of new regions using the
cached parameters. Problem: mv88e6xxx keeps the region pointers in
chip->ports[port].region, and these will remain stale after DSA frees
them. There are many things DSA can do, but updating mv88e6xxx's
private pointers is not one of them.
3. Just let the driver do it (i.e. introduce a very specific method
called ds->ops->port_reinit_as_unused, which unregisters its devlink
port devlink regions, then the old devlink port, then registers the
new one, then the devlink port regions for it). While it does work,
as opposed to the others, it's pretty horrible from an API
perspective and we can do better.
4. Introduce a new pair of methods, ->port_setup and ->port_teardown,
which in the case of mv88e6xxx must register and unregister the
devlink port regions. Call these 2 methods when the port must be
reinitialized as unused.
Naturally, I went for the 4th approach.
Fixes: 08156ba430 ("net: dsa: Add devlink port regions support to DSA")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It no need barrier when assigning a NULL value to an RCU protected
pointer. So use RCU_INIT_POINTER() instead for more fast.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
lock_sock_fast() and lock_sock_nested() contain lockdep annotations for the
sock::sk_lock.owned 'mutex'. sock::sk_lock.owned is not a regular mutex. It
is just lockdep wise equivalent. In fact it's an open coded trivial mutex
implementation with some interesting features.
sock::sk_lock.slock is a regular spinlock protecting the 'mutex'
representation sock::sk_lock.owned which is a plain boolean. If 'owned' is
true, then some other task holds the 'mutex', otherwise it is uncontended.
As this locking construct is obviously endangered by lock ordering issues as
any other locking primitive it got lockdep annotated via a dedicated
dependency map sock::sk_lock.dep_map which has to be updated at the lock
and unlock sites.
lock_sock_nested() is a straight forward 'mutex' lock operation:
might_sleep();
spin_lock_bh(sock::sk_lock.slock)
while (!try_lock(sock::sk_lock.owned)) {
spin_unlock_bh(sock::sk_lock.slock);
wait_for_release();
spin_lock_bh(sock::sk_lock.slock);
}
The lockdep annotation for sock::sk_lock.owned is for unknown reasons
_after_ the lock has been acquired, i.e. after the code block above and
after releasing sock::sk_lock.slock, but inside the bottom halves disabled
region:
spin_unlock(sock::sk_lock.slock);
mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_);
local_bh_enable();
The placement after the unlock is obvious because otherwise the
mutex_acquire() would nest into the spin lock held region.
But that's from the lockdep perspective still the wrong place:
1) The mutex_acquire() is issued _after_ the successful acquisition which
is pointless because in a dead lock scenario this point is never
reached which means that if the deadlock is the first instance of
exposing the wrong lock order lockdep does not have a chance to detect
it.
2) It only works because lockdep is rather lax on the context from which
the mutex_acquire() is issued. Acquiring a mutex inside a bottom halves
and therefore non-preemptible region is obviously invalid, except for a
trylock which is clearly not the case here.
This 'works' stops working on RT enabled kernels where the bottom halves
serialization is done via a local lock, which exposes this misplacement
because the 'mutex' and the local lock nest the wrong way around and
lockdep complains rightfully about a lock inversion.
The placement is wrong since the initial commit a5b5bb9a05 ("[PATCH]
lockdep: annotate sk_locks") which introduced this.
Fix it by moving the mutex_acquire() in front of the actual lock
acquisition, which is what the regular mutex_lock() operation does as well.
lock_sock_fast() is not that straight forward. It looks at the first glance
like a convoluted trylock operation:
spin_lock_bh(sock::sk_lock.slock)
if (!sock::sk_lock.owned)
return false;
while (!try_lock(sock::sk_lock.owned)) {
spin_unlock_bh(sock::sk_lock.slock);
wait_for_release();
spin_lock_bh(sock::sk_lock.slock);
}
spin_unlock(sock::sk_lock.slock);
mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_);
local_bh_enable();
return true;
But that's not the case: lock_sock_fast() is an interesting optimization
for short critical sections which can run with bottom halves disabled and
sock::sk_lock.slock held. This allows to shortcut the 'mutex' operation in
the non contended case by preventing other lockers to acquire
sock::sk_lock.owned because they are blocked on sock::sk_lock.slock, which
in turn avoids the overhead of doing the heavy processing in release_sock()
including waking up wait queue waiters.
In the contended case, i.e. when sock::sk_lock.owned == true the behavior
is the same as lock_sock_nested().
Semantically this shortcut means, that the task acquired the 'mutex' even
if it does not touch the sock::sk_lock.owned field in the non-contended
case. Not telling lockdep about this shortcut acquisition is hiding
potential lock ordering violations in the fast path.
As a consequence the same reasoning as for the above lock_sock_nested()
case vs. the placement of the lockdep annotation applies.
The current placement of the lockdep annotation was just copied from
the original lock_sock(), now renamed to lock_sock_nested(),
implementation.
Fix this by moving the mutex_acquire() in front of the actual lock
acquisition and adding the corresponding mutex_release() into
unlock_sock_fast(). Also document the fast path return case with a comment.
Reported-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes below Errors reported by checkpatch
ERROR: do not initialise globals to 0
+int cipso_v4_rbm_optfmt = 0;
Signed-off-by: wangzhitong <wangzhitong@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The key_domain member in struct net only exists if we define CONFIG_KEYS.
So we should add the define when we used key_domain.
Fixes: 9b24261051 ("keys: Network namespace domain tag")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.
What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.
This message can be seen in a loop, and it hangs the reboot process there:
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
So why 3?
A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:
dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold
So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.
Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.
It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.
So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.
However, complications arise really quickly.
The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).
Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.
So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.
So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.
The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.
The answer to that question lies in this comment above device_link_add:
* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).
so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This retrieves the address pairs of all subflows currently
active for a given mptcp connection.
It re-uses the same meta-header as for MPTCP_TCPINFO.
A new structure is provided to hold the subflow
address data:
struct mptcp_subflow_addrs {
union {
__kernel_sa_family_t sa_family;
struct sockaddr sa_local;
struct sockaddr_in sin_local;
struct sockaddr_in6 sin6_local;
struct sockaddr_storage ss_local;
};
union {
struct sockaddr sa_remote;
struct sockaddr_in sin_remote;
struct sockaddr_in6 sin6_remote;
struct sockaddr_storage ss_remote;
};
};
Usage of the new getsockopt is very similar to
MPTCP_TCPINFO one.
Userspace allocates a
'struct mptcp_subflow_data', followed by one or
more 'struct mptcp_subflow_addrs', then inits the
mptcp_subflow_data structure as follows:
struct mptcp_subflow_addrs *sf_addr;
struct mptcp_subflow_data *addr;
socklen_t olen = sizeof(*addr) + (8 * sizeof(*sf_addr));
addr = malloc(olen);
addr->size_subflow_data = sizeof(*addr);
addr->num_subflows = 0;
addr->size_kernel = 0;
addr->size_user = sizeof(struct mptcp_subflow_addrs);
sf_addr = (struct mptcp_subflow_addrs *)(addr + 1);
and then retrieves the endpoint addresses via:
ret = getsockopt(fd, SOL_MPTCP, MPTCP_SUBFLOW_ADDRS,
addr, &olen);
If the call succeeds, kernel will have added up to 8
endpoint addresses after the 'mptcp_subflow_data' header.
Userspace needs to re-check 'olen' value to detect how
many bytes have been filled in by the kernel.
Userspace can check addr->num_subflows to discover when
there were more subflows that available data space.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to retrieve TCP_INFO data of all subflows.
Users need to pre-initialize a meta header that has to be
prepended to the data buffer that will be filled with the tcp info data.
The meta header looks like this:
struct mptcp_subflow_data {
__u32 size_subflow_data;/* size of this structure in userspace */
__u32 num_subflows; /* must be 0, set by kernel */
__u32 size_kernel; /* must be 0, set by kernel */
__u32 size_user; /* size of one element in data[] */
} __attribute__((aligned(8)));
size_subflow_data has to be set to 'sizeof(struct mptcp_subflow_data)'.
This allows to extend mptcp_subflow_data structure later on without
breaking backwards compatibility.
If the structure is extended later on, kernel knows where the
userspace-provided meta header ends, even if userspace uses an older
(smaller) version of the structure.
num_subflows must be set to 0. If the getsockopt request succeeds (return
value is 0), it will be updated to contain the number of active subflows
for the given logical connection.
size_kernel must be set to 0. If the getsockopt request is successful,
it will contain the size of the 'struct tcp_info' as known by the kernel.
This is informational only.
size_user must be set to 'sizeof(struct tcp_info)'.
This allows the kernel to only fill in the space reserved/expected by
userspace.
Example:
struct my_tcp_info {
struct mptcp_subflow_data d;
struct tcp_info ti[2];
};
struct my_tcp_info ti;
socklen_t olen;
memset(&ti, 0, sizeof(ti));
ti.d.size_subflow_data = sizeof(struct mptcp_subflow_data);
ti.d.size_user = sizeof(struct tcp_info);
olen = sizeof(ti);
ret = getsockopt(fd, SOL_MPTCP, MPTCP_TCPINFO, &ti, &olen);
if (ret < 0)
die_perror("getsockopt MPTCP_TCPINFO");
mptcp_subflow_data.num_subflows is populated with the number of
subflows that exist on the kernel side for the logical mptcp connection.
This allows userspace to re-try with a larger tcp_info array if the number
of subflows was larger than the available space in the ti[] array.
olen has to be set to the number of bytes that userspace has allocated to
receive the kernel data. It will be updated to contain the real number
bytes that have been copied to by the kernel.
In the above example, if the number if subflows was 1, olen is equal to
'sizeof(struct mptcp_subflow_data) + sizeof(struct tcp_info).
For 2 or more subflows olen is equal to 'sizeof(struct my_tcp_info)'.
If there was more data that could not be copied due to lack of space
in the option buffer, userspace can detect this by checking
mptcp_subflow_data->num_subflows.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its not compatible with multipath-tcp.org kernel one.
1. The out-of-tree implementation defines a different 'struct mptcp_info',
with embedded __user addresses for additional data such as
endpoint addresses.
2. Mat Martineau points out that embedded __user addresses doesn't work
with BPF_CGROUP_RUN_PROG_GETSOCKOPT() which assumes that copying in
optsize bytes from optval provides all data that got copied to userspace.
This provides mptcp_info data for the given mptcp socket.
Userspace sets optlen to the size of the structure it expects.
The kernel updates it to contain the number of bytes that it copied.
This allows to append more information to the structure later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be re-used from getsockopt path.
Since diag can be a module, we can't export the helper from diag, it
needs to be moved to core.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-09-17
We've added 63 non-merge commits during the last 12 day(s) which contain
a total of 65 files changed, 2653 insertions(+), 751 deletions(-).
The main changes are:
1) Streamline internal BPF program sections handling and
bpf_program__set_attach_target() in libbpf, from Andrii.
2) Add support for new btf kind BTF_KIND_TAG, from Yonghong.
3) Introduce bpf_get_branch_snapshot() to capture LBR, from Song.
4) IMUL optimization for x86-64 JIT, from Jie.
5) xsk selftest improvements, from Magnus.
6) Introduce legacy kprobe events support in libbpf, from Rafael.
7) Access hw timestamp through BPF's __sk_buff, from Vadim.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (63 commits)
selftests/bpf: Fix a few compiler warnings
libbpf: Constify all high-level program attach APIs
libbpf: Schedule open_opts.attach_prog_fd deprecation since v0.7
selftests/bpf: Switch fexit_bpf2bpf selftest to set_attach_target() API
libbpf: Allow skipping attach_func_name in bpf_program__set_attach_target()
libbpf: Deprecated bpf_object_open_opts.relaxed_core_relocs
selftests/bpf: Stop using relaxed_core_relocs which has no effect
libbpf: Use pre-setup sec_def in libbpf_find_attach_btf_id()
bpf: Update bpf_get_smp_processor_id() documentation
libbpf: Add sphinx code documentation comments
selftests/bpf: Skip btf_tag test if btf_tag attribute not supported
docs/bpf: Add documentation for BTF_KIND_TAG
selftests/bpf: Add a test with a bpf program with btf_tag attributes
selftests/bpf: Test BTF_KIND_TAG for deduplication
selftests/bpf: Add BTF_KIND_TAG unit tests
selftests/bpf: Change NAME_NTH/IS_NAME_NTH for BTF_KIND_TAG format
selftests/bpf: Test libbpf API function btf__add_tag()
bpftool: Add support for BTF_KIND_TAG
libbpf: Add support for BTF_KIND_TAG
libbpf: Rename btf_{hash,equal}_int to btf_{hash,equal}_int_tag
...
====================
Link: https://lore.kernel.org/r/20210917173738.3397064-1-ast@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devlink core exported generously the functions calls that were used
by netdevsim tests or not used at all.
Delete such APIs with one exception - devlink_alloc_ns(). That function
should be spared from deleting because it is a special form of devlink_alloc()
needed for the netdevsim.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RFC8998 specification defines the use of the ShangMi algorithm
cipher suites in TLS 1.3, and also supports the GCM/CCM mode using
the SM4 algorithm.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when unbinding the mv88e6xxx driver on Turris MOX, these error
messages appear:
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 0 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 100 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 0 from fdb: -2
(and similarly for other ports)
What happens is that DSA has a policy "even if there are bugs, let's at
least not leak memory" and dsa_port_teardown() clears the dp->fdbs and
dp->mdbs lists, which are supposed to be empty.
But deleting that cleanup code, the warnings go away.
=> the FDB and MDB lists (used for refcounting on shared ports, aka CPU
and DSA ports) will eventually be empty, but are not empty by the time
we tear down those ports. Aka we are deleting them too soon.
The addresses that DSA complains about are host-trapped addresses: the
local addresses of the ports, and the MAC address of the bridge device.
The problem is that offloading those entries happens from a deferred
work item scheduled by the SWITCHDEV_FDB_DEL_TO_DEVICE handler, and this
races with the teardown of the CPU and DSA ports where the refcounting
is kept.
In fact, not only it races, but fundamentally speaking, if we iterate
through the port list linearly, we might end up tearing down the shared
ports even before we delete a DSA user port which has a bridge upper.
So as it turns out, we need to first tear down the user ports (and the
unused ones, for no better place of doing that), then the shared ports
(the CPU and DSA ports). In between, we need to ensure that all work
items scheduled by our switchdev handlers (which only run for user
ports, hence the reason why we tear them down first) have finished.
Fixes: 161ca59d39 ("net: dsa: reference count the MDB entries at the cross-chip notifier level")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914134726.2305133-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need in specific devlink_param_*publish(), because same
output can be achieved by using devlink_params_*publish() in correct
places.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6tables only sets the `IP6T_F_PROTO` flag on a rule if a protocol is
specified (`-p tcp`, for example). However, if the flag is not set,
`ip6_packet_match` doesn't call `ipv6_find_hdr` for the skb, in which
case the fragment offset is left uninitialized and a garbage value is
passed to each matcher.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
mq / mqprio make the default child qdiscs visible. They only do
so for the qdiscs which are within real_num_tx_queues when the
device is registered. Depending on order of calls in the driver,
or if user space changes config via ethtool -L the number of
qdiscs visible under tc qdisc show will differ from the number
of queues. This is confusing to users and potentially to system
configuration scripts which try to make sure qdiscs have the
right parameters.
Add a new Qdisc_ops callback and make relevant qdiscs TTRT.
Note that this uncovers the "shortcut" created by
commit 1f27cde313 ("net: sched: use pfifo_fast for non real queues")
The default child qdiscs beyond initial real_num_tx are always
pfifo_fast, no matter what the sysfs setting is. Fixing this
gets a little tricky because we'd need to keep a reference
on whatever the default qdisc was at the time of creation.
In practice this is likely an non-issue the qdiscs likely have
to be configured to non-default settings, so whatever user space
is doing such configuration can replace the pfifos... now that
it will see them.
Reported-by: Matthew Massey <matthewmassey@fb.com>
Reviewed-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This configuration knob is very sensible, it should be notified when
changing.
Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
>From a userland POV, this API was based on some magic values:
- dirmask and action were bitfields but meaning of bits
(XFRM_POL_DEFAULT_*) are not exported;
- action is confusing, if a bit is set, does it mean drop or accept?
Let's try to simplify this uapi by using explicit field and macros.
Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This drops the code setting bit 9 on egress frames on the
Realtek "type A" (RTL8366RB) frames.
This bit was set on ingress frames for unknown reason,
and was set on egress frames as the format of ingress
and egress frames was believed to be the same. As that
assumption turned out to be false, and since this bit
seems to have zero effect on the behaviour of the switch
let's drop this bit entirely.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210913143156.1264570-1-linus.walleij@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The __alloc_frag_align() is short, and only called by two functions,
so inline page_frag_alloc_align() for reduce the overhead of calls.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shouldn't happen, but can happen that readable eeprom size is smaller
than announced. Then we would be stuck in an endless loop here because
after reaching the actual end reads return eeprom.len = 0. I faced this
issue when making a mistake in driver development. Detect this scenario
and return an error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d7807a9adf.
As mentioned in https://lkml.org/lkml/2021/9/13/1819
5 years old commit 919483096b ("ipv4: fix memory leaks in ip_cmsg_send() callers")
was a correct fix.
ip_cmsg_send() can loop over multiple cmsghdr()
If IP_RETOPTS has been successful, but following cmsghdr generates an error,
we do not free ipc.ok
If IP_RETOPTS is not successful, we have freed the allocated temporary space,
not the one currently in ipc.opt.
Sure, code could be refactored, but let's not bring back old bugs.
Fixes: d7807a9adf ("Revert "ipv4: fix memory leaks in ip_cmsg_send() callers"")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be5692), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2021-09-14
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 13 day(s) which contain
a total of 18 files changed, 334 insertions(+), 193 deletions(-).
The main changes are:
1) Fix mmap_lock lockdep splat in BPF stack map's build_id lookup, from Yonghong Song.
2) Fix BPF cgroup v2 program bypass upon net_cls/prio activation, from Daniel Borkmann.
3) Fix kvcalloc() BTF line info splat on oversized allocation attempts, from Bixuan Cui.
4) Fix BPF selftest build of task_pt_regs test for arm64/s390, from Jean-Philippe Brucker.
5) Fix BPF's disasm.{c,h} to dual-license so that it is aligned with bpftool given the former
is a build dependency for the latter, from Daniel Borkmann with ACKs from contributors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With SMC-Dv2 users can configure if the static system EID should be used
during CLC handshake, or if only user EIDs are allowed.
Add generic netlink support to enable and disable the system EID, and
to retrieve the system EID and its current enabled state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system EID is retrieved using an registered ISM device each time
when needed. This adds some unnecessary complexity at all places where
the system EID is needed, but no ISM device is at hand.
Simplify the code and save the system EID in a static variable in
smc_ism.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC-Dv2 allows users to define EIDs which allows to create separate
name spaces enabling users to cluster their SMC-Dv2 connections.
Add support for user defined EIDs and extent the generic netlink
interface so users can add, remove and dump EIDs.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix cgroup v1 interference when non-root cgroup v2 BPF programs are used.
Back in the days, commit bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
embedded per-socket cgroup information into sock->sk_cgrp_data and in order
to save 8 bytes in struct sock made both mutually exclusive, that is, when
cgroup v1 socket tagging (e.g. net_cls/net_prio) is used, then cgroup v2
falls back to the root cgroup in sock_cgroup_ptr() (&cgrp_dfl_root.cgrp).
The assumption made was "there is no reason to mix the two and this is in line
with how legacy and v2 compatibility is handled" as stated in bd1060a1d6.
However, with Kubernetes more widely supporting cgroups v2 as well nowadays,
this assumption no longer holds, and the possibility of the v1/v2 mixed mode
with the v2 root fallback being hit becomes a real security issue.
Many of the cgroup v2 BPF programs are also used for policy enforcement, just
to pick _one_ example, that is, to programmatically deny socket related system
calls like connect(2) or bind(2). A v2 root fallback would implicitly cause
a policy bypass for the affected Pods.
In production environments, we have recently seen this case due to various
circumstances: i) a different 3rd party agent and/or ii) a container runtime
such as [0] in the user's environment configuring legacy cgroup v1 net_cls
tags, which triggered implicitly mentioned root fallback. Another case is
Kubernetes projects like kind [1] which create Kubernetes nodes in a container
and also add cgroup namespaces to the mix, meaning programs which are attached
to the cgroup v2 root of the cgroup namespace get attached to a non-root
cgroup v2 path from init namespace point of view. And the latter's root is
out of reach for agents on a kind Kubernetes node to configure. Meaning, any
entity on the node setting cgroup v1 net_cls tag will trigger the bypass
despite cgroup v2 BPF programs attached to the namespace root.
Generally, this mutual exclusiveness does not hold anymore in today's user
environments and makes cgroup v2 usage from BPF side fragile and unreliable.
This fix adds proper struct cgroup pointer for the cgroup v2 case to struct
sock_cgroup_data in order to address these issues; this implicitly also fixes
the tradeoffs being made back then with regards to races and refcount leaks
as stated in bd1060a1d6, and removes the fallback, so that cgroup v2 BPF
programs always operate as expected.
[0] https://github.com/nestybox/sysbox/
[1] https://kind.sigs.k8s.io/
Fixes: bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/bpf/20210913230759.2313-1-daniel@iogearbox.net
ip_vs_conn_tab_bits may be provided by the user through the
conn_tab_bits module parameter. If this value is greater than 31, or
less than 0, the shift operator used to derive tab_size causes undefined
behaviour.
Fix this checking ip_vs_conn_tab_bits value to be in the range specified
in ipvs Kconfig. If not, simply use default value.
Fixes: 6f7edb4881 ("IPVS: Allow boot time change of hash size")
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This makes use of bt_skb_sendmmsg instead using memcpy_from_msg which
is not considered safe to be used when lock_sock is held.
Also make rfcomm_dlc_send handle skb with fragments and queue them all
atomically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes use of bt_skb_sendmsg instead of allocating a different
buffer to be used with memcpy_from_msg which cause one extra copy.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove unneeded line break between pr_debug and arguments.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
only increase fib6_sernum in net namespace after add fib6_info
successfully.
Signed-off-by: zhang kai <zhangkaiheb@126.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c10355 ("tipc: resolve race problem at unicast message reception")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.
Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
$ifconfig eth2 1.1.1.1/16 up
$ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
$ip link set dev eth2_19503 up
$ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
$ip link set dev eth2_19504 up
$ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
$ip link set dev eth2_19505 up
$ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
$ip link set dev eth2_19506 up
NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.
$ip link set dev eth2_19504 down
This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.
In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.
Fixes: cc4e3835ef ("udp_tunnel: add central NIC RX port offload infrastructure")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 919483096b.
There is only when ip_options_get() return zero need to free.
It already called kfree() when return error.
Fixes: 919483096b ("ipv4: fix memory leaks in ip_cmsg_send() callers")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
vduse driver supporting blk
virtio-vsock support for end of record with SEQPACKET
vdpa: mac and mq support for ifcvf and mlx5
vdpa: management netlink for ifcvf
virtio-i2c, gpio dt bindings
misc fixes, cleanups
NB: when merging this with
b542e383d8 ("eventfd: Make signal recursion protection a task bit")
from Linus' tree, replace eventfd_signal_count with
eventfd_signal_allowed, and drop the export of eventfd_wake_count from
("eventfd: Export eventfd_wake_count to modules").
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmE1+awPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpt6EIAJy0qrc62lktNA0IiIVJSLbUbTMmFj8MzkGR
8UxZdhpjWqBPJPyaOuNeksAqTGm/UAPEYx3C2c95Jhej7anFpy7dbCtIXcPHLJME
DjcJg+EDrlNCj8m0FcsHpHWsFzPMERJpyEZNxgB5WazQbv+yWhGrg2FN5DCnF0Ro
ZFYeKSVty148pQ0nHl8X0JM2XMtqit+O+LvKN2HQZ+fubh7BCzMxzkHY0QLHIzUS
UeZqd3Qm8YcbqnlX38P5D6k+NPiTEgknmxaBLkPxg6H3XxDAmaIRFb8Ldd1rsgy1
zTLGDiSGpVDIpawRnuEAzqJThV3Y5/MVJ1WD+mDYQ96tmhfp+KY=
=DBH/
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- vduse driver ("vDPA Device in Userspace") supporting emulated virtio
block devices
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
BPF programs may want to know hardware timestamps if NIC supports
such timestamping.
Expose this data as hwtstamp field of __sk_buff the same way as
gso_segs/gso_size. This field could be accessed from the same
programs as tstamp field, but it's read-only field. Explicit test
to deny access to padding data is added to bpf_skb_is_valid_access.
Also update BPF_PROG_TEST_RUN tests of the feature.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210909220409.8804-2-vfedorenko@novek.ru
Add pr_fmt macro to spell out the source of messages in prefix.
Before this patch:
packet size is too long (1543 > 1518)
With this patch:
af_packet: packet size is too long (1543 > 1518)
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This splits the msft_do_{open/close} to msft_do_{open/close} and
msft_{register/unregister}. With this change it is possible to retain
the MSFT extension info irrespective of controller power on/off state.
This helps bluetoothd to report correct 'supported features' of the
controller to the D-Bus clients event if the controller is off. It also
re-reads the MSFT info upon every msft_do_open().
The following test steps were performed.
1. Boot the test device and verify the MSFT support debug log in syslog.
2. Power off the controller and read the 'supported features', power on
and read again.
3. Restart the bluetoothd and verify the 'supported features' value.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot hit shift-out-of-bounds in xfrm_get_default. The problem was in
missing validation check for user data.
up->dirmask comes from user-space, so we need to check if this value
is less than XFRM_USERPOLICY_DIRMASK_MAX to avoid shift-out-of-bounds bugs.
Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Reported-and-tested-by: syzbot+b2be9dd8ca6f6c73ee2d@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.
Fix this issue by decrease the reference count before jumping to the
label invalid.
Fixes: 4522a70db7 ("l2tp: fix reading optional fields of L2TPv3")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported another data-race in af_unix [1]
Lets change __skb_insert() to use WRITE_ONCE() when changing
skb head qlen.
Also, change unix_dgram_poll() to use lockless version
of unix_recvq_full()
It is verry possible we can switch all/most unix_recvq_full()
to the lockless version, this will be done in a future kernel version.
[1] HEAD commit: 8596e589b7
BUG: KCSAN: data-race in skb_queue_tail / unix_dgram_poll
write to 0xffff88814eeb24e0 of 4 bytes by task 25815 on cpu 0:
__skb_insert include/linux/skbuff.h:1938 [inline]
__skb_queue_before include/linux/skbuff.h:2043 [inline]
__skb_queue_tail include/linux/skbuff.h:2076 [inline]
skb_queue_tail+0x80/0xa0 net/core/skbuff.c:3264
unix_dgram_sendmsg+0xff2/0x1600 net/unix/af_unix.c:1850
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2532
__do_sys_sendmmsg net/socket.c:2561 [inline]
__se_sys_sendmmsg net/socket.c:2558 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2558
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
skb_queue_len include/linux/skbuff.h:1869 [inline]
unix_recvq_full net/unix/af_unix.c:194 [inline]
unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
sock_poll+0x23e/0x260 net/socket.c:1288
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll fs/eventpoll.c:846 [inline]
ep_send_events fs/eventpoll.c:1683 [inline]
ep_poll fs/eventpoll.c:1798 [inline]
do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
__do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
__se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
__x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000001b -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G W 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 86b18aaa2b ("skbuff: fix a data race in skb_queue_len()")
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a couple of harmless fixes, increase max tcp msize (64KB -> 1MB),
and increase default msize (8KB -> 128KB)
The default increase has been discussed with Christian
for the qemu side of things but makes sense for all supported
transports
-----BEGIN PGP SIGNATURE-----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=PLhf
-----END PGP SIGNATURE-----
Merge tag '9p-for-5.15-rc1' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"A couple of harmless fixes, increase max tcp msize (64KB -> 1MB), and
increase default msize (8KB -> 128KB)
The default increase has been discussed with Christian for the qemu
side of things but makes sense for all supported transports"
* tag '9p-for-5.15-rc1' of git://github.com/martinetd/linux:
net/9p: increase default msize to 128k
net/9p: use macro to define default msize
net/9p: increase tcp max msize to 1MB
9p/xen: Fix end of loop tests for list_for_each_entry
9p/trans_virtio: Remove sysfs file on probe failure
The kernel test robot reports:
[ 843.509974][ T345] =============================
[ 843.524220][ T345] WARNING: suspicious RCU usage
[ 843.538791][ T345] 5.14.0-rc2-00606-g889b7da23abf #1 Not tainted
[ 843.553617][ T345] -----------------------------
[ 843.567412][ T345] net/mctp/route.c:310 RCU-list traversed in non-reader section!!
- we're missing the rcu read lock acquire around the destruction path.
This change adds the acquire/release - the path is already atomic, and
we're using the _rcu list iterators.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.
When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.
This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.
The patch prevents cloned socks from referencing the same ccid.
Fixes: 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...")
Signed-off-by: Zhenpeng Lin <zplin@psu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_prog_test_run_xattr takes a struct __sk_buff, but did not permit
that __skbuff to include an nonzero ingress_ifindex.
This patch updates to allow ingress_ifindex, convert the __sk_buff field to
sk_buff (skb_iif) and back, and tests that the value is present from on BPF
program side. The test sets an unlikely distinct value for ingress_ifindex
(11) from ifindex (1), which is in line with the rest of the synthetic field
tests.
Adding this support allows testing BPF that operates differently on
incoming and outgoing skbs by discriminating on this field.
Signed-off-by: Neil Spring <ntspring@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210831033356.1459316-1-ntspring@fb.com
Currently usb tranport is not allowed to suspend when SCO over
HCI tranport is active.
This patch shall enable the usb tranport to suspend when SCO
link use non-HCI transport.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Allow user level process to enable / disable codec offload
feature through mgmt interface. By default offload codec feature
is disabled.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In Enhanced_Setup_Synchronous_Command, add support for msbc
coding format
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For HFP offload use case, codec needs to be configured
before opening SCO connection. This patch sends
HCI_CONFIGURE_DATA_PATH command to configure doec before
opening SCO connection.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch allows user space to set the codec that needs to
be used for HFP offload use case. The codec details are cached and
the controller is configured before opening the SCO connection.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add BT_CODEC option for getsockopt systemcall to get the details
of offload codecs supported over SCO socket
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move reading of supported local codecs into a separate init function,
query codecs capabilities and cache the data
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL
address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Zvuz
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes and stragglers from Jakub Kicinski:
"Networking stragglers and fixes, including changes from netfilter,
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable
BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing
v6LL address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx
descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address"
* tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
ieee802154: Remove redundant initialization of variable ret
net: stmmac: fix MAC not working when system resume back with WoL active
net: phylink: add suspend/resume support
net: renesas: sh_eth: Fix freeing wrong tx descriptor
bonding: 3ad: pass parameter bond_params by reference
cxgb3: fix oops on module removal
can: c_can: fix null-ptr-deref on ioctl()
can: rcar_canfd: add __maybe_unused annotation to silence warning
net: wwan: iosm: Unify IO accessors used in the driver
net: wwan: iosm: Replace io.*64_lo_hi() with regular accessors
net: qcom/emac: Replace strlcpy with strscpy
ip6_gre: Revert "ip6_gre: add validation for csum_start"
net: hns3: make hclgevf_cmd_caps_bit_map0 and hclge_cmd_caps_bit_map0 static
selftests/bpf: Test XDP bonding nest and unwind
bonding: Fix negative jump label count on nested bonding
MAINTAINERS: add VM SOCKETS (AF_VSOCK) entry
stmmac: dwmac-loongson:Fix missing return value
iwlwifi: fix printk format warnings in uefi.c
net: create netdev->dev_addr assignment helpers
bnxt_en: Fix possible unintended driver initiated error recovery
...
The variable ret is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9cf448c200.
This commit was added for equivalence with a similar fix to ip_gre.
That fix proved to have a bug. Upon closer inspection, ip6_gre is not
susceptible to the original bug.
So revert the unnecessary extra check.
In short, ipgre_xmit calls skb_pull to remove ipv4 headers previously
inserted by dev_hard_header. ip6gre_tunnel_xmit does not.
Link: https://lore.kernel.org/netdev/CA+FuTSe+vJgTVLc9SojGuN-f9YQ+xWLPKE_S4f=f+w+_P2hgUg@mail.gmail.com/#t
Fixes: 9cf448c200 ("ip6_gre: add validation for csum_start")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record is supported via MSG_EOR flag, while current logic operates
with message, so rename variables from 'record' to 'message'.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20210903123306.3273757-1-arseny.krasnov@kaspersky.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This current implemented bit is used to mark end of messages
('EOM' - end of message), not records('EOR' - end of record).
Also rename 'record' to 'message' in implementation as it is
different things.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20210903123109.3273053-1-arseny.krasnov@kaspersky.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The GRE tunnel device can pull existing outer headers in ipge_xmit.
This is a rare path, apparently unique to this device. The below
commit ensured that pulling does not move skb->data beyond csum_start.
But it has a false positive if ip_summed is not CHECKSUM_PARTIAL and
thus csum_start is irrelevant.
Refine to exclude this. At the same time simplify and strengthen the
test.
Simplify, by moving the check next to the offending pull, making it
more self documenting and removing an unnecessary branch from other
code paths.
Strengthen, by also ensuring that the transport header is correct and
therefore the inner headers will be after skb_reset_inner_headers.
The transport header is set to csum_start in skb_partial_csum_set.
Link: https://lore.kernel.org/netdev/YS+h%2FtqCJJiQei+W@shredder/
Fixes: 1d011c4803 ("ip_gre: add validation for csum_start")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE interfaces are not Ether-like and therefore it is not
possible to generate the v6LL address the same way as (for example)
GRETAP devices.
With default settings, a GRE interface will attempt generating its v6LL
address using the EUI64 approach, but this will fail when the local
endpoint of the GRE tunnel is set to "any". In this case the GRE
interface will end up with no v6LL address, thus violating RFC4291.
SIT interfaces already implement a different logic to ensure that a v6LL
address is always computed.
Change the GRE v6LL generation logic to follow the same approach as SIT.
This way GRE interfaces will always have a v6LL address as well.
Behaviour of GRETAP interfaces has not been changed as they behave like
classic Ether-like interfaces.
To avoid code duplication sit_add_v4_addrs() has been renamed to
add_v4_addrs() and adapted to handle also the IP6GRE/GRE cases.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
