This function can work just fine with const pointer, it only calls
alloc_netdev which take const as well. Moreover it makes this function
more flexible as some cfg80211 callback may provide const char * as
well, e.g. add_virtual_intf. This will be needed for more advanced
interface management.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing P2P interface is handled by sending a proper request to the
firmware. On success firmware triggers an event and driver's handler
removes a matching interface.
However on event timeout we remove interface directly from the cfg80211
callback. Current code doesn't handle this case correctly as it always
assumes rtnl to be unlocked.
Fix it by adding an extra rtnl_locked parameter to functions and calling
unregister_netdevice when needed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modern C standards expect the 'inline' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/wireless/intel/ipw2x00/ipw2200.c:4096:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modern C standards expect the 'static' keyword to come first in a
declaration, and we get a warning for this with "make W=1":
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3353:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'register' is a keyword in C and cannot be used in place of a
variable name, as shown by this -Wextra warning:
drivers/net/wireless/cisco/airo.c:1105:29: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
This replaces the 'register' keyword with a 'reg' identifier in
the declaration, which matches the definition and has the intended
meaning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that if interface type is changed from managed to
__ap, AP can be successfully started. But there is a problem if new
ap interface is added.
The problem got resolved after sending appropriate commands to firmware
in add_interface handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch populates secondary channel offset and downloads it to
firmware to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some platforms, driver is unable to wakeup firmware after system resume
due to a problem at MMC subsystem. Triggering card reset in this case has
a race with card removal from MMC which causes system hang. This patch
resolves the problem by not triggering card reset.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is obeserved that sometimes scan operation will block the disconnect
during system suspend. It's ok to cancel ongoing scan in this case. It
reduces unnecessary system suspend delay.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch creates common function mwifiex_cancel_scan to remove
duplication of code.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When an association command is sent to firmware but the process is
killed before the command response arrives, driver will try to
access bss_desc which is already freed. This issue is fixed by
checking return value of bss_start.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compiling the rtlwifi drivers for ARM with gcc -Wextra warns about lots of
incorrect code that results from 'char' being unsigned here, e.g.
realtek/rtlwifi/rc.c:113:18: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8188ee/dm.c:1070:22: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ce/trx.c:54:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192cu/mac.c:601:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192de/trx.c:53:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ee/phy.c:1268:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192se/rf.c:150:20: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/dm.c:877:29: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/phy.c:386:16: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/dm.c:1514:38: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:1558:11: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:386:24: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/trx.c:55:12: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/stats.c:31:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
This patch changes all uses of 'char' in this driver that refer to
8-bit integers to use 's8' instead, which is signed on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
lbs_mac_event_disconnected may free priv->currenttxskb
while lbs_hard_start_xmit accesses to it.
The patch adds a spinlock for mutual exclusion.
Tested on OLPC XO-1 (usb8388) and XO-1.5 (sd8686) with v4.7-rc3.
Confirmed that lbs_mac_event_disconnected is being called on the
station when hostapd on access point is given SIGHUP.
Signed-off-by: Pavel <andrianov@ispras.ru>
Tested-by: James Cameron <quozl@laptop.org>
Acked-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pdev_data pointer is being freed with kfree but the pointer is not dynamic allocated.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph specifier to dump small buffers in hex format instead of doing this
byte-by-byte.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This also renames REG_USB_AGG_{TO,TH} to REG_USB_AGG_{TIMEOUT,THRESH}
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Documentation for enabling USB aggregation and whether to select
interrupt or bulk delivery of interrupt events.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
&priv->cmd_work per priv, which maps to lbtf_cmd_work) is involved in
actual command processing and may be used on a memory reclaim path.
The workitems require forward progress under memory pressure and hence,
WQ_MEM_RECLAIM has been set. Since there are only a fixed number of work
items, explicit concurrency limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This change reorders some operations in brcmf_setup_ifmodes in hope to
make it simpler:
1) It allocates arrays right before filling them. This way it's easier
to follow requested array length as it's immediately followed by
code filling it. It's easier to check e.g. why we need 4 entries for
P2P. Other than that it deduplicates some checks (e.g. for P2P).
2) It reorders code to first prepare limits and then define a new combo.
Previously this was mixed (e.g. we were setting num of channels
before preparing limits).
3) It modifies mbss code to use i variable just like other combos do.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXaRfMAAoJEG4XJFUm622bxwEH/iZm3o752MM62fJyCOEtEN6R
8vL7kyehX81G9szQyQ7bMQ7y0diobeBGsu8e7zzV4Mt+cU0Z9g/ezfca6HfE6Hrh
0ubKl/tSzAhRcAoQiNyKOI36yt455r1Mnr8a18OYO79pnNcjf7kSd7pJG2BW0Hdx
dRsSxzcg+E0w4z7mJ/cgM5aRzjXmXvAUjw9cIt36y3+ng1fQ+M782lkCtscMZY3Q
e5bkLCaP5TG+O9niPTjzrAzMlBTGwopknuEZnwIGDkNkx1PeBzRATVGeSa9Zba6d
g17kGbP7QT1GaCJF/FfWColaVpMBDhviovQANeoaUi804C4ZKNZAcJirZC3W2eM=
=uYcn
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.8
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
Calling sdio_claim_host() from the interface independent part of
the mwifiex driver is not only a layering violation, but also causes
a link error if MMC support is disabled, or if CONFIG_MMC=m
and CONFIG_MWIFIEX=y:
drivers/net/built-in.o: In function `mwifiex_fw_dpc':
:(.text+0xff138): undefined reference to `sdio_claim_host'
:(.text+0xff158): undefined reference to `sdio_release_host'
The right way to do this is to have the sdio specific code in the
sdio driver front-end, and we already have a callback pointer that
we can use for this after exporting the generic fw download
function from the core driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 65c71efe1c ("mwifiex: fix racing condition when downloading firmware")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this including cfg80211.h in a wrong order could result in:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:122:24: error: array type has incomplete element type
struct brcmf_wsec_key key[BRCMF_MAX_DEFAULT_KEYS];
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:291:24: error: field ‘p2p’ has incomplete type
struct brcmf_p2p_info p2p;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:297:27: error: field ‘pmk_list’ has incomplete type
struct brcmf_pmk_list_le pmk_list;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:317:28: error: field ‘assoclist’ has incomplete type
struct brcmf_assoclist_le assoclist;
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This attribute was added 3 years ago by
commit 3eacf86655 ("brcmfmac: introduce brcmf_cfg80211_vif structure")
but it remains unused since then. It seems we can safely drop it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per Michael Büsch: "All a-phy code is usused", so remove it all.
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 reports the following error with -Werror=unused-const-variable.
drivers/net/wireless/broadcom/b43/phy_a.c:576:40: error:
'b43_phyops_a' defined but not used
Per Michael Büsch: "All a-phy code is usused", so remove it all,
and move the remaining Type-G initialization code into phy_g.c.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue replaces deprecated create_workqueue().
In if_sdio.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_sdio_host_to_card_worker.
The workitem is involved in sending packets to firmware.
Forward progress under memory pressure is a requirement here.
In if_spi.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_spi_host_to_card_worker.
The workitem is involved in sending command packets from the host.
Forward progress under memory pressure is a requirement here.
Dedicated workqueues have been used in both cases since the workitems
on the workqueues are involved in normal device operation with
WQ_MEM_RECLAIM set to gurantee forward progress under memory pressure.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the calls to flush_workqueue() before
destroy_workqueue() have been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bus rx sequence is not in order because that control and event
frames always cause immediate send, but data frames may be held
for glomming in firmware side. It is not actually an error as the
packets are still processed even if the RX sequence is not in order.
Therefor the error message is rephrased and changed to a debug
message.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for the new PCIE devices 43525 and 43465.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using nmap tool with FMAC, the nmap packets were be dropped by kernel
because the size was too short. The kernel message showed like
"nmap: packet size is too short (42 <= 50)". It is caused by the packet
length is shorter than ndev->hard_header_len. According to definition of
LL_RESERVED_SPACE() and hard_header_len, we should use hard_header_len
to reserve for L2 header, like ethernet header(ETH_HLEN) in our case and
use needed_headroom for the additional headroom needed by hardware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error message is given for something that is not an error here as
the drive strength configuration may not be applicable for specific
devices. Therefor the error message is rephrased and changed to a
debug message.
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
[arend@broadcom.com: rephrase commit message]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SKBs can come with a prioriy. Currently a priority of 0..7 is
assumed. But this assumption is incorrect. To fix this any
priority of 0 or higher then 7 will be adjusted by calling
cfg80211_classify8021d
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only hardcode the LED behavior if the SROM doesn't provide any for all
LEDs of the card. This avoids instantiating LED triggers for unconnected
LEDs, while (hopefully) keeping things working for old cards with a
blank SROM.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 reports:
drivers/net/wireless/marvell/libertas_tf/main.c:30:19: error:
'lbtf_driver_version' defined but not used
with -Werror=unused-const-variable=.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are nine copies of the _rtl88ee_read_adapter_info() function,
and most but not all of them cause a build warning in some configurations:
rtl8192de/hw.c: In function '_rtl92de_read_adapter_info':
rtl8192de/hw.c:1767:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
rtl8723ae/hw.c: In function '_rtl8723e_read_adapter_info.constprop':
rtlwifi/rtl8723ae/hw.c:1654:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem is that when rtlefuse->epromtype is something other than
EEPROM_BOOT_EFUSE, the rest of the function uses undefined data, resulting
in random behavior later.
Apparently, in some drivers, the problem was already found and fixed
but the fix did not make it into the others.
This picks one approach to deal with the problem and applies identical
code to all 9 files, to simplify the later consolidation of those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two firmware events we handle similarly in brcmfmac:
BRCMF_E_LINK and BRCMF_E_IF. The difference from firmware point of view
is that the first one means BSS remains present in the firmware. Trying
to (re)create it (e.g. when adding new virtual interface) will result in
an error.
Current code treats both events in a similar way. It removes Linux
interface for each of them. It works OK with e.g. BCM43602. Its firmware
generates both events for each interface. It means we get BRCMF_E_LINK
and remove interface. That is soon followed by BRCMF_E_IF which means
BSS was also removed in a firmware. The only downside of this is a
harmless error like:
[ 208.643180] brcmfmac: brcmf_fweh_call_event_handler: no interface object
Unfortunately BCM4366 firmware doesn't automatically remove BSS and so
it doesn't generate BRCMF_E_IF. In such case we incorrectly remove Linux
interface on BRCMF_E_LINK as BSS is still present in the firmware. It
results in an error when trying to re-create virtual interface, e.g.:
> iw phy phy1 interface add wlan1-1 type __ap
[ 3602.929199] brcmfmac: brcmf_ap_add_vif: timeout occurred
command failed: I/O error (-5)
With this patch we don't remove Linux interface while firmware keeps
BSS. Thanks to this we keep a consistent states of host driver and
device firmware.
Further improvement should be to mark BSS as disabled and remove
interface on BRCMF_E_LINK. Then we should add support for reusing
BSS-es.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware for new chipsets is based on a new major version of code
internally maintained at Broadcom. E.g. brcmfmac4366b-pcie.bin (used for
BCM4366B1) is based on 10.10.69.3309 while brcmfmac43602-pcie.ap.bin was
based on 7.35.177.56.
Currently setting AP 5 GHz channel doesn't work reliably with BCM4366B1.
When setting e.g. 36 control channel with VHT80 (center channel 42)
firmware may randomly pick one of:
1) 52 control channel with 58 as center one
2) 100 control channel with 106 as center one
3) 116 control channel with 122 as center one
4) 149 control channel with 155 as center one
It seems new firmwares require setting AP mode (BRCMF_C_SET_AP) before
specifying a channel. Changing an order of firmware calls fixes the
problem. This requirement resulted in two separated "chanspec" calls,
one in AP code path and one in P2P path.
This fix was verified with BCM4366B1 and tested for regressions on
BCM43602.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 on x86 started warning about wl3501_get_encode when building
with -O2:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_get_encode’:
drivers/net/wireless/wl3501_cs.c:1769:5: warning: ‘implemented’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1686:19: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1702:20: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1719:23: warning: ‘txpow’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1752:20: warning: ‘retry’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1806:25: warning: ‘pwr_state’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1383:24: warning: ‘value’ may be used uninitialized in this function
I could not figure out what exactly confuses gcc here, but splitting the
wl3501_get_mib_value function into two helps the compiler to figure out
that the variables are not actually used uninitialized, and makes it
slightly clearer to a human reader what the function actually does and
which parts of it are under the spinlock.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document lists the possible compatible strings that a SDIO child
node can have, so the driver checks if the defined in the node matches.
But the error message when that's not the case is misleading, so change
for one that makes clear what the error really is. Also, returning a -1
as errno code is not correct since that's -EPERM. A -EINVAL seems to be
a more appropriate one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document say that the "interrupts" property in the child node is
optional. So the property being missed shouldn't be treated as an error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function can fail so the returned value should be checked
and the error propagated to the caller in case of a failure.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's better to have the device name prefixed in the error message.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of duplicating part of the cleanups needed in case of an error
in .probe callback, have a single error path and use goto labels as is
common practice in the kernel.
This also has the nice side effect that the cleanup operations are made
in the inverse order of their counterparts, which was not the case for
the mwifiex_add_card() error path.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's only a check if mwifiex_add_card() returned a nonzero value, but
the actual error code is neither stored nor propagated to the caller. So
instead of always returning -1 (which is -EPERM and not a suitable errno
code in this case), propagate the value returned by mwifiex_add_card().
Patch also removes the assignment of sdio_disable_func() returned value
since it was overwritten anyways and what matters is to know the error
value returned by the first function that failed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the sdio_enable_func() function fails on .probe, the -EIO errno code
is always returned but that could make more difficult to debug and find
the cause of why the function actually failed.
Since the driver/device core prints the value returned by .probe in its
error message propagate what was returned by sdio_enable_func() at fail.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO is an auto enumerable bus so the SDIO devices are matched using the
sdio_device_id table and not using compatible strings from a OF id table.
However, commit ce4f6f0c35 ("mwifiex: add platform specific wakeup
interrupt support") allowed to match nodes defined as child of the SDIO
host controller in the probe function using a compatible string to setup
platform specific parameters in the DT.
The problem is that the OF parse function is always called regardless if
the SDIO dev has an OF node associated or not, and prints an error if it
is not found. So, on a platform that doesn't have a node for a SDIO dev,
the following misleading error message will be printed:
[ 12.480042] mwifiex_sdio mmc2:0001:1: sdio platform data not available
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is helpful for debugging. Without this all I was getting from "iw"
command on failed creating of P2P interface was:
> command failed: Too many open files in system (-23)
Signed-off-by: Rafal Milecki <zajec5@gmail.com>
[arend@broadcom.com: reduce error prints upon iface creation]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch ensures that 'locally_generated' parameter is correctly
passed to cfg80211_disconnected() API.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The GFP_DMA flag is obviously misunderstood in the mwifiex driver. It's
meant for legacy ISA DMA memory mappings only -- the lower 16MB on x86.
That doesn't apply to PCIe or SDIO devices, I guess.
Remove the GFP_DMA flag to reduce the need to place the socket buffer
allocation into the low mem DMA area, which might already be in use by
other drivers.
This misuse was flagged by the PaX USERCOPY feature by chance, as it
detected the user copy operation from a DMA buffer in the recvfrom()
syscall path.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is important for brcmfmac as some of released firmwares (e.g.
brcmfmac4366b-pcie.bin) may pick different channel than requested. This
has been tested with BCM4366B1 in D-Link DIR-885L.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
