Enable support for process-scoped invalidations from nested
guests and partition-scoped invalidations for nested guests.
Process-scoped invalidations for any level of nested guests
are handled by implementing H_RPT_INVALIDATE handler in the
nested guest exit path in L0.
Partition-scoped invalidation requests are forwarded to the
right nested guest, handled there and passed down to L0
for eventual handling.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
[aneesh: Nested guest partition-scoped invalidation changes]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Squash in fixup patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210621085003.904767-5-bharata@linux.ibm.com
H_RPT_INVALIDATE does two types of TLB invalidations:
1. Process-scoped invalidations for guests when LPCR[GTSE]=0.
This is currently not used in KVM as GTSE is not usually
disabled in KVM.
2. Partition-scoped invalidations that an L1 hypervisor does on
behalf of an L2 guest. This is currently handled
by H_TLB_INVALIDATE hcall and this new replaces the old that.
This commit enables process-scoped invalidations for L1 guests.
Support for process-scoped and partition-scoped invalidations
from/for nested guests will be added separately.
Process scoped tlbie invalidations from L1 and nested guests
need RS register for TLBIE instruction to contain both PID and
LPID. This patch introduces primitives that execute tlbie
instruction with both PID and LPID set in prepartion for
H_RPT_INVALIDATE hcall.
A description of H_RPT_INVALIDATE follows:
int64 /* H_Success: Return code on successful completion */
/* H_Busy - repeat the call with the same */
/* H_Parameter, H_P2, H_P3, H_P4, H_P5 : Invalid
parameters */
hcall(const uint64 H_RPT_INVALIDATE, /* Invalidate RPT
translation
lookaside information */
uint64 id, /* PID/LPID to invalidate */
uint64 target, /* Invalidation target */
uint64 type, /* Type of lookaside information */
uint64 pg_sizes, /* Page sizes */
uint64 start, /* Start of Effective Address (EA)
range (inclusive) */
uint64 end) /* End of EA range (exclusive) */
Invalidation targets (target)
-----------------------------
Core MMU 0x01 /* All virtual processors in the
partition */
Core local MMU 0x02 /* Current virtual processor */
Nest MMU 0x04 /* All nest/accelerator agents
in use by the partition */
A combination of the above can be specified,
except core and core local.
Type of translation to invalidate (type)
---------------------------------------
NESTED 0x0001 /* invalidate nested guest partition-scope */
TLB 0x0002 /* Invalidate TLB */
PWC 0x0004 /* Invalidate Page Walk Cache */
PRT 0x0008 /* Invalidate caching of Process Table
Entries if NESTED is clear */
PAT 0x0008 /* Invalidate caching of Partition Table
Entries if NESTED is set */
A combination of the above can be specified.
Page size mask (pages)
----------------------
4K 0x01
64K 0x02
2M 0x04
1G 0x08
All sizes (-1UL)
A combination of the above can be specified.
All page sizes can be selected with -1.
Semantics: Invalidate radix tree lookaside information
matching the parameters given.
* Return H_P2, H_P3 or H_P4 if target, type, or pageSizes parameters
are different from the defined values.
* Return H_PARAMETER if NESTED is set and pid is not a valid nested
LPID allocated to this partition
* Return H_P5 if (start, end) doesn't form a valid range. Start and
end should be a valid Quadrant address and end > start.
* Return H_NotSupported if the partition is not in running in radix
translation mode.
* May invalidate more translation information than requested.
* If start = 0 and end = -1, set the range to cover all valid
addresses. Else start and end should be aligned to 4kB (lower 11
bits clear).
* If NESTED is clear, then invalidate process scoped lookaside
information. Else pid specifies a nested LPID, and the invalidation
is performed on nested guest partition table and nested guest
partition scope real addresses.
* If pid = 0 and NESTED is clear, then valid addresses are quadrant 3
and quadrant 0 spaces, Else valid addresses are quadrant 0.
* Pages which are fully covered by the range are to be invalidated.
Those which are partially covered are considered outside
invalidation range, which allows a caller to optimally invalidate
ranges that may contain mixed page sizes.
* Return H_SUCCESS on success.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210621085003.904767-4-bharata@linux.ibm.com
Add a field to mmu_psize_def to store the page size encodings
of H_RPT_INVALIDATE hcall. Initialize this while scanning the radix
AP encodings. This will be used when invalidating with required
page size encoding in the hcall.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210621085003.904767-3-bharata@linux.ibm.com
The type values H_RPTI_TYPE_PRT and H_RPTI_TYPE_PAT indicate
invalidating the caching of process and partition scoped entries
respectively.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210621085003.904767-2-bharata@linux.ibm.com
The POWER9 vCPU TLB management code assumes all threads in a core share
a TLB, and that TLBIEL execued by one thread will invalidate TLBs for
all threads. This is not the case for SMT8 capable POWER9 and POWER10
(big core) processors, where the TLB is split between groups of threads.
This results in TLB multi-hits, random data corruption, etc.
Fix this by introducing cpu_first_tlb_thread_sibling etc., to determine
which siblings share TLBs, and use that in the guest TLB flushing code.
[npiggin@gmail.com: add changelog and comment]
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210602040441.3984352-1-npiggin@gmail.com
POWER9 and later processors always go via the P9 guest entry path now.
Remove the remaining support from the P7/8 path.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-33-npiggin@gmail.com
Implement support for hash guests under hash host. This has to save and
restore the host SLB, and ensure that the MMU is off while switching
into the guest SLB.
POWER9 and later CPUs now always go via the P9 path. The "fast" guest
mode is now renamed to the P9 mode, which is consistent with its
functionality and the rest of the naming.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-32-npiggin@gmail.com
Implement hash guest support. Guest entry/exit has to restore and
save/clear the SLB, plus several other bits to accommodate hash guests
in the P9 path. Radix host, hash guest support is removed from the P7/8
path.
The HPT hcalls and faults are not handled in real mode, which is a
performance regression. A worst-case fork/exit microbenchmark takes 3x
longer after this patch. kbuild benchmark performance is in the noise,
but the slowdown is likely to be noticed somewhere.
For now, accept this penalty for the benefit of simplifying the P7/8
paths and unifying P9 hash with the new code, because hash is a less
important configuration than radix on processors that support it. Hash
will benefit from future optimisations to this path, including possibly
a faster path to handle such hcalls and interrupts without doing a full
exit.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-31-npiggin@gmail.com
The reflection of sc 1 interrupts from guest PR=1 to the guest kernel is
required to support a hash guest running PR KVM where its guest is
making hcalls with sc 1.
In preparation for hash guest support, add this hcall reflection to the
P9 path. The P7/8 path does this in its realmode hcall handler
(sc_1_fast_return).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-30-npiggin@gmail.com
In order to support hash guests in the P9 path (which does not do real
mode hcalls or page fault handling), these real-mode hash specific
interrupts need to be implemented in virt mode.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-29-npiggin@gmail.com
All radix guests go via the P9 path now, so there is no need to limit
nested HV to processors that support "mixed mode" MMU. Remove the
restriction.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-27-npiggin@gmail.com
Commit f3c18e9342 ("KVM: PPC: Book3S HV: Use XICS hypercalls when
running as a nested hypervisor") added nested HV tests in XICS
hypercalls, but not all are required.
* icp_eoi is only called by kvmppc_deliver_irq_passthru which is only
called by kvmppc_check_passthru which is only caled by
kvmppc_read_one_intr.
* kvmppc_read_one_intr is only called by kvmppc_read_intr which is only
called by the L0 HV rmhandlers code.
* kvmhv_rm_send_ipi is called by:
- kvmhv_interrupt_vcore which is only called by kvmhv_commence_exit
which is only called by the L0 HV rmhandlers code.
- icp_send_hcore_msg which is only called by icp_rm_set_vcpu_irq.
- icp_rm_set_vcpu_irq which is only called by icp_rm_try_update
- icp_rm_set_vcpu_irq is not nested HV safe because it writes to
LPCR directly without a kvmhv_on_pseries test. Nested handlers
should not in general be using the rm handlers.
The important test seems to be in kvmppc_ipi_thread, which sends the
virt-mode H_IPI handler kick to use smp_call_function rather than
msgsnd.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-26-npiggin@gmail.com
Now that the P7/8 path no longer supports radix, real-mode handlers
do not need to deal with being called in virt mode.
This change effectively reverts commit acde25726b ("KVM: PPC: Book3S
HV: Add radix checks in real-mode hypercall handlers").
It removes a few more real-mode tests in rm hcall handlers, which
allows the indirect ops for the xive module to be removed from the
built-in xics rm handlers.
kvmppc_h_random is renamed to kvmppc_rm_h_random to be a bit more
descriptive and consistent with other rm handlers.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-25-npiggin@gmail.com
The P9 path now runs all supported radix guest combinations, so
remove radix guest support from the P7/8 path.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-24-npiggin@gmail.com
Dependent-threads mode is the normal KVM mode for pre-POWER9 SMT
processors, where all threads in a core (or subcore) would run the same
partition at the same time, or they would run the host.
This design was mandated by MMU state that is shared between threads in
a processor, so the synchronisation point is in hypervisor real-mode
that has essentially no shared state, so it's safe for multiple threads
to gather and switch to the correct mode.
It is implemented by having the host unplug all secondary threads and
always run in SMT1 mode, and host QEMU threads essentially represent
virtual cores that wake these secondary threads out of unplug when the
ioctl is called to run the guest. This happens via a side-path that is
mostly invisible to the rest of the Linux host and the secondary threads
still appear to be unplugged.
POWER9 / ISA v3.0 has a more flexible MMU design that is independent
per-thread and allows a much simpler KVM implementation. Before the new
"P9 fast path" was added that began to take advantage of this, POWER9
support was implemented in the existing path which has support to run
in the dependent threads mode. So it was not much work to add support to
run POWER9 in this dependent threads mode.
The mode is not required by the POWER9 MMU (although "mixed-mode" hash /
radix MMU limitations of early processors were worked around using this
mode). But it is one way to run SMT guests without running different
guests or guest and host on different threads of the same core, so it
could avoid or reduce some SMT attack surfaces without turning off SMT
entirely.
This security feature has some real, if indeterminate, value. However
the old path is lagging in features (nested HV), and with this series
the new P9 path adds remaining missing features (radix prefetch bug
and hash support, in later patches), so POWER9 dependent threads mode
support would be the only remaining reason to keep that code in and keep
supporting POWER9/POWER10 in the old path. So here we make the call to
drop this feature.
Remove dependent threads mode support for POWER9 and above processors.
Systems can still achieve this security by disabling SMT entirely, but
that would generally come at a larger performance cost for guests.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-23-npiggin@gmail.com
Rather than partition the guest PID space + flush a rogue guest PID to
work around this problem, instead fix it by always disabling the MMU when
switching in or out of guest MMU context in HV mode.
This may be a bit less efficient, but it is a lot less complicated and
allows the P9 path to trivally implement the workaround too. Newer CPUs
are not subject to this issue.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-22-npiggin@gmail.com
Move MMU context switch as late as reasonably possible to minimise code
running with guest context switched in. This becomes more important when
this code may run in real-mode, with later changes.
Move WARN_ON as early as possible so program check interrupts are less
likely to tangle everything up.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-21-npiggin@gmail.com
This is a first step to wrapping supervisor and user SPR saving and
loading up into helpers, which will then be called independently in
bare metal and nested HV cases in order to optimise SPR access.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-20-npiggin@gmail.com
The C conversion caused exit timing to become a bit cramped. Expand it
to cover more of the entry and exit code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-18-npiggin@gmail.com
SRR0/1, DAR, DSISR must all be protected from machine check which can
clobber them. Ensure MSR[RI] is clear while they are live.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-17-npiggin@gmail.com
Now the initial C implementation is done, inline more HV code to make
rearranging things easier.
And rename __kvmhv_vcpu_entry_p9 to drop the leading underscores as it's
now C, and is now a more complete vcpu entry.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-16-npiggin@gmail.com
Almost all logic is moved to C, by introducing a new in_guest mode for
the P9 path that branches very early in the KVM interrupt handler to P9
exit code.
The main P9 entry and exit assembly is now only about 160 lines of low
level stack setup and register save/restore, plus a bad-interrupt
handler.
There are two motivations for this, the first is just make the code more
maintainable being in C. The second is to reduce the amount of code
running in a special KVM mode, "realmode". In quotes because with radix
it is no longer necessarily real-mode in the MMU, but it still has to be
treated specially because it may be in real-mode, and has various
important registers like PID, DEC, TB, etc set to guest. This is hostile
to the rest of Linux and can't use arbitrary kernel functionality or be
instrumented well.
This initial patch is a reasonably faithful conversion of the asm code,
but it does lack any loop to return quickly back into the guest without
switching out of realmode in the case of unimportant or easily handled
interrupts. As explained in previous changes, handling HV interrupts
very quickly in this low level realmode is not so important for P9
performance, and are important to avoid for security, observability,
debugability reasons.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-15-npiggin@gmail.com
In the interest of minimising the amount of code that is run in
"real-mode", don't handle hcalls in real mode in the P9 path. This
requires some new handlers for H_CEDE and xics-on-xive to be added
before xive is pulled or cede logic is checked.
This introduces a change in radix guest behaviour where radix guests
that execute 'sc 1' in userspace now get a privilege fault whereas
previously the 'sc 1' would be reflected as a syscall interrupt to the
guest kernel. That reflection is only required for hash guests that run
PR KVM.
Background:
In POWER8 and earlier processors, it is very expensive to exit from the
HV real mode context of a guest hypervisor interrupt, and switch to host
virtual mode. On those processors, guest->HV interrupts reach the
hypervisor with the MMU off because the MMU is loaded with guest context
(LPCR, SDR1, SLB), and the other threads in the sub-core need to be
pulled out of the guest too. Then the primary must save off guest state,
invalidate SLB and ERAT, and load up host state before the MMU can be
enabled to run in host virtual mode (~= regular Linux mode).
Hash guests also require a lot of hcalls to run due to the nature of the
MMU architecture and paravirtualisation design. The XICS interrupt
controller requires hcalls to run.
So KVM traditionally tries hard to avoid the full exit, by handling
hcalls and other interrupts in real mode as much as possible.
By contrast, POWER9 has independent MMU context per-thread, and in radix
mode the hypervisor is in host virtual memory mode when the HV interrupt
is taken. Radix guests do not require significant hcalls to manage their
translations, and xive guests don't need hcalls to handle interrupts. So
it's much less important for performance to handle hcalls in real mode on
POWER9.
One caveat is that the TCE hcalls are performance critical, real-mode
variants introduced for POWER8 in order to achieve 10GbE performance.
Real mode TCE hcalls were found to be less important on POWER9, which
was able to drive 40GBe networking without them (using the virt mode
hcalls) but performance is still important. These hcalls will benefit
from subsequent guest entry/exit optimisation including possibly a
faster "partial exit" that does not entirely switch to host context to
handle the hcall.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-14-npiggin@gmail.com
Switching the MMU from radix<->radix mode is tricky particularly as the
MMU can remain enabled and requires a certain sequence of SPR updates.
Move these together into their own functions.
This also includes the radix TLB check / flush because it's tied in to
MMU switching due to tlbiel getting LPID from LPIDR.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-13-npiggin@gmail.com
Move the xive management up so the low level register switching can be
pushed further down in a later patch. XIVE MMIO CI operations can run in
higher level code with machine checks, tracing, etc., available.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-12-npiggin@gmail.com
irq_work's use of the DEC SPR is racy with guest<->host switch and guest
entry which flips the DEC interrupt to guest, which could lose a host
work interrupt.
This patch closes one race, and attempts to comment another class of
races.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-11-npiggin@gmail.com
LPCR[HDICE]=0 suppresses hypervisor decrementer exceptions on some
processors, so it must be enabled before HDEC is set.
Rather than set it in the host LPCR then setting HDEC, move the HDEC
update to after the guest MMU context (including LPCR) is loaded.
There shouldn't be much concern with delaying HDEC by some 10s or 100s
of nanoseconds by setting it a bit later.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-10-npiggin@gmail.com
This is more symmetric with kvmppc_xive_push_vcpu, and has the advantage
that it runs with the MMU on.
The extra test added to the asm will go away with a future change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-9-npiggin@gmail.com
This sets up the same calling convention from interrupt entry to
KVM interrupt handler for system calls as exists for other interrupt
types.
This is a better API, it uses a save area rather than SPR, and it has
more registers free to use. Using a single common API helps maintain
it, and it becomes easier to use in C in a later patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-8-npiggin@gmail.com
The bad_host_intr check will never be true with PR KVM, move
it to HV code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-7-npiggin@gmail.com
Like the earlier patch for hcalls, KVM interrupt entry requires a
different calling convention than the Linux interrupt handlers
set up. Move the code that converts from one to the other into KVM.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-6-npiggin@gmail.com
System calls / hcalls have a different calling convention than
other interrupts, so there is code in the KVMTEST to massage these
into the same form as other interrupt handlers.
Move this work into the KVM hcall handler. This means teaching KVM
a little more about the low level interrupt handler setup, PACA save
areas, etc., although that's not obviously worse than the current
approach of coming up with an entirely different interrupt register
/ save convention.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-5-npiggin@gmail.com
Add a separate hcall entry point. This can be used to deal with the
different calling convention.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-4-npiggin@gmail.com
Move the GUEST_MODE_SKIP logic into KVM code. This is quite a KVM
internal detail that has no real need to be in common handlers.
Add a comment explaining the what and why of KVM "skip" interrupts.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-3-npiggin@gmail.com
Rather than bifurcate the call depending on whether or not HV is
possible, and have the HV entry test for PR, just make a single
common point which does the demultiplexing. This makes it simpler
to add another type of exit handler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210528090752.3542186-2-npiggin@gmail.com
Similar to commit 25edcc50d7 ("KVM: PPC: Book3S HV: Save and restore
FSCR in the P9 path"), ensure the P7/8 path saves and restores the host
FSCR. The logic explained in that patch actually applies there to the
old path well: a context switch can be made before kvmppc_vcpu_run_hv
restores the host FSCR and returns.
Now both the p9 and the p7/8 paths now save and restore their FSCR, it
no longer needs to be restored at the end of kvmppc_vcpu_run_hv
Fixes: b005255e12 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs")
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210526125851.3436735-1-npiggin@gmail.com
Here are 2 driver fixes for driver core changes that happened in
5.13-rc1.
The clk driver fix resolves a many-reported issue with booting some
devices, and the USB typec fix resolves the reported problem of USB
systems on some embedded boards.
Both of these have been in linux-next this week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYKDc2A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylF8QCeIeAZ24HKyzGiS2CPYHEHBdiip40An1eefar7
WvvZuHQCZV3gfVEHdVpp
=jCwI
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver fixes for driver core changes that happened in
5.13-rc1.
The clk driver fix resolves a many-reported issue with booting some
devices, and the USB typec fix resolves the reported problem of USB
systems on some embedded boards.
Both of these have been in linux-next this week with no reported
issues"
* tag 'driver-core-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
clk: Skip clk provider registration when np is NULL
usb: typec: tcpm: Don't block probing of consumers of "connector" nodes
Here are some small IIO driver fixes and one Staging driver fix for
5.13-rc2.
Nothing major, just some resolutions for reported problems:
- gcc11 bogus warning fix for rtl8723bs
- iio driver tiny fixes
All of these have been in linux-next for many days with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYKDcQA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk8hQCg0+YRIUZfhBm1qUiq9JuTBr62kM8An2qYpr9Q
8iiAoBETOYo5P5HByG52
=Dyx9
-----END PGP SIGNATURE-----
Merge tag 'staging-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small IIO driver fixes and one Staging driver fix for
5.13-rc2.
Nothing major, just some resolutions for reported problems:
- gcc-11 bogus warning fix for rtl8723bs
- iio driver tiny fixes
All of these have been in linux-next for many days with no reported
issues"
* tag 'staging-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: tsl2583: Fix division by a zero lux_val
iio: core: return ENODEV if ioctl is unknown
iio: core: fix ioctl handlers removal
iio: gyro: mpu3050: Fix reported temperature value
iio: hid-sensors: select IIO_TRIGGERED_BUFFER under HID_SENSOR_IIO_TRIGGER
iio: proximity: pulsedlight: Fix rumtime PM imbalance on error
iio: light: gp2ap002: Fix rumtime PM imbalance on error
staging: rtl8723bs: avoid bogus gcc warning
Here are some small USB fixes for 5.13-rc2. They consist of a number of
resolutions for reported issues:
- typec fixes for found problems
- xhci fixes and quirk additions
- dwc3 driver fixes
- minor fixes found by Coverity
- cdc-wdm fixes for reported problems
All of these have been in linux-next for a few days with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYKDexQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk72gCffEE5ZfO64iFqARPx9Mim04YaSDUAnRJM1mBk
dsRT2X0yddqdKek6fN+g
=C9x7
-----END PGP SIGNATURE-----
Merge tag 'usb-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.13-rc2. They consist of a number
of resolutions for reported issues:
- typec fixes for found problems
- xhci fixes and quirk additions
- dwc3 driver fixes
- minor fixes found by Coverity
- cdc-wdm fixes for reported problems
All of these have been in linux-next for a few days with no reported
issues"
* tag 'usb-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usb: core: hub: fix race condition about TRSMRCY of resume
usb: typec: tcpm: Fix SINK_DISCOVERY current limit for Rp-default
xhci: Add reset resume quirk for AMD xhci controller.
usb: xhci: Increase timeout for HC halt
xhci: Do not use GFP_KERNEL in (potentially) atomic context
xhci: Fix giving back cancelled URBs even if halted endpoint can't reset
xhci-pci: Allow host runtime PM as default for Intel Alder Lake xHCI
usb: musb: Fix an error message
usb: typec: tcpm: Fix wrong handling for Not_Supported in VDM AMS
usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work
usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4
usb: fotg210-hcd: Fix an error message
docs: usb: function: Modify path name
usb: dwc3: omap: improve extcon initialization
usb: typec: ucsi: Put fwnode in any case during ->probe()
usb: typec: tcpm: Fix wrong handling in GET_SINK_CAP
usb: dwc2: Remove obsolete MODULE_ constants from platform.c
usb: dwc3: imx8mp: fix error return code in dwc3_imx8mp_probe()
usb: dwc3: imx8mp: detect dwc3 core node via compatible string
usb: dwc3: gadget: Return success always for kick transfer in ep queue
...
- Use the ALARM feature check in the alarmtimer core code insted of
the old method of checking for the set_alarm() callback. Drivers
can have that callback set but the feature bit cleared. If such
a RTC device is selected then alarms wont work.
- Use a proper define to let the preprocessor check whether Hyper-V VDSO
clocksource should be active. The code used a constant in an enum with
#ifdef, which evaluates to always false and disabled the clocksource
for VDSO.
-----BEGIN PGP SIGNATURE-----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=TruV
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2021-05-16' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two fixes for timers:
- Use the ALARM feature check in the alarmtimer core code insted of
the old method of checking for the set_alarm() callback.
Drivers can have that callback set but the feature bit cleared. If
such a RTC device is selected then alarms wont work.
- Use a proper define to let the preprocessor check whether Hyper-V
VDSO clocksource should be active.
The code used a constant in an enum with #ifdef, which evaluates to
always false and disabled the clocksource for VDSO"
* tag 'timers-urgent-2021-05-16' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/hyper-v: Re-enable VDSO_CLOCKMODE_HVCLOCK on X86
alarmtimer: Check RTC features instead of ops
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYKC7SQAKCRCAXGG7T9hj
vpmTAQCmz5LvFHN9eAfq5jwz4cMvrN5h8aWnZjChgiAFZl0T7wD/TEDjtK18piUM
xWjZDUefMonnk0U8+bPityDmt8UV2AI=
=KFFw
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- two patches for error path fixes
- a small series for fixing a regression with swiotlb with Xen on Arm
* tag 'for-linus-5.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/swiotlb: check if the swiotlb has already been initialized
arm64: do not set SWIOTLB_NO_FORCE when swiotlb is required
xen/arm: move xen_swiotlb_detect to arm/swiotlb-xen.h
xen/unpopulated-alloc: fix error return code in fill_list()
xen/gntdev: fix gntdev_mmap() error exit path
- Reorganize SEV code to streamline and simplify future development
-----BEGIN PGP SIGNATURE-----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=ENfF
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v5.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"The three SEV commits are not really urgent material. But we figured
since getting them in now will avoid a huge amount of conflicts
between future SEV changes touching tip, the kvm and probably other
trees, sending them to you now would be best.
The idea is that the tip, kvm etc branches for 5.14 will all base
ontop of -rc2 and thus everything will be peachy. What is more, those
changes are purely mechanical and defines movement so they should be
fine to go now (famous last words).
Summary:
- Enable -Wundef for the compressed kernel build stage
- Reorganize SEV code to streamline and simplify future development"
* tag 'x86_urgent_for_v5.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/compressed: Enable -Wundef
x86/msr: Rename MSR_K8_SYSCFG to MSR_AMD64_SYSCFG
x86/sev: Move GHCB MSR protocol and NAE definitions in a common header
x86/sev-es: Rename sev-es.{ch} to sev.{ch}
- Fix a regression in the conversion of the 64-bit BookE interrupt entry to C.
- Fix KVM hosts running with the hash MMU since the recent KVM gfn changes.
- Fix a deadlock in our paravirt spinlocks when hcall tracing is enabled.
- Several fixes for oopses in our runtime code patching for security mitigations.
- A couple of minor fixes for the recent conversion of 32-bit interrupt entry/exit to C.
- Fix __get_user() causing spurious crashes in sigreturn due to a bad inline asm
constraint, spotted with GCC 11.
- A fix for the way we track IRQ masking state vs NMI interrupts when using the new scv
system call entry path.
- A couple more minor fixes.
Thanks to: Cédric Le Goater, Christian Zigotzky, Christophe Leroy, Naveen N. Rao, Nicholas
Piggin Paul Menzel, Sean Christopherson.
-----BEGIN PGP SIGNATURE-----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=V7PP
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a regression in the conversion of the 64-bit BookE interrupt
entry to C.
- Fix KVM hosts running with the hash MMU since the recent KVM gfn
changes.
- Fix a deadlock in our paravirt spinlocks when hcall tracing is
enabled.
- Several fixes for oopses in our runtime code patching for security
mitigations.
- A couple of minor fixes for the recent conversion of 32-bit interrupt
entry/exit to C.
- Fix __get_user() causing spurious crashes in sigreturn due to a bad
inline asm constraint, spotted with GCC 11.
- A fix for the way we track IRQ masking state vs NMI interrupts when
using the new scv system call entry path.
- A couple more minor fixes.
Thanks to Cédric Le Goater, Christian Zigotzky, Christophe Leroy,
Naveen N. Rao, Nicholas Piggin Paul Menzel, and Sean Christopherson.
* tag 'powerpc-5.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64e/interrupt: Fix nvgprs being clobbered
powerpc/64s: Make NMI record implicitly soft-masked code as irqs disabled
powerpc/64s: Fix stf mitigation patching w/strict RWX & hash
powerpc/64s: Fix entry flush patching w/strict RWX & hash
powerpc/64s: Fix crashes when toggling entry flush barrier
powerpc/64s: Fix crashes when toggling stf barrier
KVM: PPC: Book3S HV: Fix kvm_unmap_gfn_range_hv() for Hash MMU
powerpc/legacy_serial: Fix UBSAN: array-index-out-of-bounds
powerpc/signal: Fix possible build failure with unsafe_copy_fpr_{to/from}_user
powerpc/uaccess: Fix __get_user() with CONFIG_CC_HAS_ASM_GOTO_OUTPUT
powerpc/pseries: warn if recursing into the hcall tracing code
powerpc/pseries: use notrace hcall variant for H_CEDE idle
powerpc/pseries: Don't trace hcall tracing wrapper
powerpc/pseries: Fix hcall tracing recursion in pv queued spinlocks
powerpc/syscall: Calling kuap_save_and_lock() is wrong
powerpc/interrupts: Fix kuep_unlock() call
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ggm4
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2021-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Fix an idle CPU selection bug, and an AMD Ryzen maximum frequency
enumeration bug"
* tag 'sched-urgent-2021-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, sched: Fix the AMD CPPC maximum performance value on certain AMD Ryzen generations
sched/fair: Fix clearing of has_idle_cores flag in select_idle_cpu()
