In 40GE we can't use the default bw units for set ratelimit (100 Mbps)
since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units.
But for 10GE 1 Gbps units might be too bruit so we use the following solution.
For user set ratelimit <= 25 Gbps:
use 100 Mbps units * user_ratelimit (* 10).
For user set ratelimit > 25 Gbps:
use 1 Gbps units * user_ratelimit.
For user set unlimited ratelimit (0 Gbps):
use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57)
Note: any value > 58 will damage the FW ratelimit computation, so we allow
a max and any higher value will be pulled down to 57.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes issues with debug printk calls across the driver, normally
disabled; first compilation errors:
drivers/net/fddi/defxx.c:676:1: error: pasting "(" and ""In dfx_bus_init...\n"" does not give a valid preprocessing token
drivers/net/fddi/defxx.c:820:1: error: pasting "(" and ""In dfx_bus_uninit...\n"" does not give a valid preprocessing token
and so on, and then warnings:
drivers/net/fddi/defxx.c: In function 'dfx_driver_init':
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
etc. Additionally casts are removed from virtual addresses and %p used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds DMA synchronisation calls needed in the receive path:
1. To retrieve the Receive Status word that is prepended by the PDQ DMA
engine in the receive buffer, and provides information about the
frame received, including its size and any errors.
2. To make data received available for copying in the small-frame case
(size <= SKBUFF_RX_COPYBREAK) where the original DMA buffer will be
returned to the receive descriptor ring and therefore its mapping
retained.
With DMA mapping error handling in place, added by the other patch,
this may now also trigger where an attempt to map a newly allocated
buffer for DMA has failed. In that case data from the original buffer
will be copied out and the buffer returned to the DMA descriptor ring.
These calls may do nothing when data is in the host DMA addressing range
of the FDDI interface, such as always on 32-bit systems, however their
absence makes frame reception stop functioning reliably on systems that
have memory beyond the low 4GB of the address space.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds error handling for DMA mapping requests; I think there isn't
much else to say about it.
A good side-effect is the mapping in the transmit path is now made with
the board lock released. Also if DMA mapping fails for a newly
allocated receive buffer, then data from the old buffer will be copied
out (as is presently done for small frames only whose size does not
exceed SKBUFF_RX_COPYBREAK) and the original buffer returned, with its
mapping unchanged, to the DMA descriptor ring.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the two remaining places across the driver that use dev_alloc_skb
to netdev_alloc_skb. Another place has already been converted to use
__netdev_alloc_skb, no idea why these two have been left behind.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prearranged receive DMA bounce buffer mappings are not released in the
card reboot/shutdown path. That does not affect frame reception, but
probably explains the random segmentation fault I observed the other day
on interface shutdown. Card is rebooted as required by the spec in the
process of ring fault recovery when a PC Trace signal has been received.
This change fixes the problem in an obvious manner.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive DMA maps are oversized, they include EISA legacy 128-byte
alignment padding in size calculation whereas this padding is never used
for data. Worse yet, if the skb's data area has been realigned indeed,
then data beyond the end of the buffer will be synchronised from the
receive DMA bounce buffer, possibly corrupting data structures residing
in memory beyond the actual end of this data buffer.
Therefore switch to using PI_RCV_DATA_K_SIZE_MAX rather than NEW_SKB_SIZE
in DMA mapping, the value the former macro expands to is written to the
receive ring DMA descriptor of the PDQ DMA chip and determines the
maximum amount of data PDQ will ever transfer to the corresponding data
buffer, including all headers and padding.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-07-03
Please pull this first batch of wireless updates intended for the
3.17 stream...
For the mac80211 bits, Johannes says:
"The biggest thing here is probably Arik's TDLS rework, beyond that we
have smaller improvements and features like David's scanning IE thing,
Luca's queue work, some CSA work, etc. Also your PID rate control
removal, of course."
For the iwlwifi bits, Emmanuel says:
"I have here a whole bunch of various things. Andy contributes
better debug prints for dvm specific flows and a module parameter to
completely disable power save for dvm. Andrei is sharing the premises
of his work on CSA - more to come. Eran and Liad keep on working
on the new devices. I have the regular amount of BT Coex stuff and
I continue to work on the firmware error report system adding more
debug capabilities. More to come on that subject too."
On top of that, there are some cleanups to the new rsi driver, some
continuing improvements to the rtl818x drivers, and the usual bundles
of updates to ath9k, b43, mwifiex, wil6210, and a few other bits here
and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compiler warnings:
drivers/net/ethernet/amd/declance.c: In function 'lance_init_ring':
drivers/net/ethernet/amd/declance.c:478: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:487: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:503: warning: cast from pointer to integer of different size
drivers/net/ethernet/amd/declance.c:520: warning: cast from pointer to integer of different size
in 64-bit compilation. Where the value printed is an offset (whose range
will always fit) the cast uses a 32-bit type, otherwise, where it is a
host memory address, the pointer is output directly with %p. Also the
remaining `0x' prefix is dropped for consistency across these messages.
Tested with both 32-bit and 64-bit compilation, as well as at the run time
(with the debug messages affected enabled).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required. If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.
Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node. If present, use settings that work with the caches. If not
present, use settings that do not look at the caches.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides some general performance enhancements for the
driver:
- Modify the default coalescing settings (reduce usec, increase frames)
- Change the AXI burst length to 256 bytes (default was 16 bytes which
was smaller than a cache line)
- Change the AXI cache settings to write-back/write-allocate which
allocate cache entries for received packets during the DMA since the
packet will be processed soon afterwards
- Combine ioread/iowrite when disabling both the Tx and Rx interrupts
- Change to processing the Tx/Rx channels in pairs
- Only recycle the Rx descriptors when a threshold of dirty descriptors
is reached
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called. However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload. Add a call to netif_napi_del during
the ndo_stop operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal. Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.
Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic_set_coalesce() has two problems.
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings are no longer relevant. Even when last slave is
removed, there is a valid address assigned to bond (random).
The correct functionality of vlans is ensured by maintaining unicast
list in vlan_sync_address().
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the current synchron state change function and add a
new function for a state assert. Change the start and stop callbacks to
use this new synchron state change behaviour. It's a wrapper around the
async state change function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rework the irq_pol register setting for rising and falling
interrupt settings only. The default behaviour should be rising flag.
Also use IRQ_TYPE_* defines instead of IRQF_* defines. There is no
functionality change but irq_get_trigger_type returns IRQ_TYPE_* defines.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set this bit in start callback which could be
called more than once.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a complete reimplementation of transmit and receive
handling for the at86rf230 driver.
It solves also six bugs:
First:
The RX_SAFE_MODE is enabled and the transceiver doesn't leave the
receive state while the framebuffer isn't read by a CMD_FB command.
This is useful to read out the frame and don't get into another receive
or transmit state, otherwise the frame would be overwritten.
The current driver do twice CMD_FB calls, the first one leaves this
protection.
Second:
Sometimes the CRC calculation is correct and the length field is greater
127. The current mac802154 layer and filter of a at86rf2xx doesn't check
on this and the kernel crashes. In this case the frame is corrupted, we
send the whole receive buffer to the next layer which can be useful for
sniffing.
Thrid:
There is a undocumented race condition. When we are go into the
RX_AACK_ON state the transceiver could be changed into RX_AACK_BUSY
state. This is a normal behaviour. In this case the transceiver received
a SHR while assert wasn't finished.
Fourth:
It also handle some more "correct" state changes. In aret mode the
transceiver need to go to TX_ON before the transceiver go into
RX_AACK_ON.
Fifth:
The programming model [0] describes also a error handling in ARET mode
if the trac status is different than zero. This is patch adds support
for handling this.
Sixth:
In receive handling the transceiver should also get the trac status
according [0]. The driver could use the trac status as error statistic
handling, but the driver doesn't use this currently. There is maybe some
timing behaviour or the read of this register change some transceiver
states.
In addition the irqworker is removed. Instead we do async spi calls and
no scheduling is involved anymore. The transmit function is also
asynchron but with a wait_for_completion handling. The mac802154 layer
doesn't support asynchron transmit handling right now.
The state change behaviour is now changes, before it was:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. assert while(!STATE_TRANSITION_IN_PROGRESS)
4. assert once(wanted state != current state)
Sometimes a unexcepted state change occurs when 4. assert was violated.
The new state change behaviour is:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. wait state change timing according datasheet
4. assert once(wanted state != current state)
This behaviour is described in the at86rf231 software programming model [0].
The state change documentation in this programming guide should also valid for
at86rf212 and at86rf233 chips.
The transceiver don't do a FORCE_TX_ON while we want to transmit a PDU.
The new behaviour is a TX_ON and wait a receiving time (tFrame + tPAck).
If we are still in RX_AACK_BUSY then we transmit a FORCE_TX_ON as timeout
handling. The different is that FORCE_TX_ON aborts receiving and TX_ON
waits if RX_AACK_BUSY is finished. This should decrease the drop rate of
packets.
[0] http://www.atmel.com/Images/AVR2022_swpm231-2.0.zip
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To set the CCA_ED_THRES register the calculation for at86rf23x is
different than for at86rf212. This patch adds a new callback for this
calculation in chip data struct.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new at86rf2xx_chip_data structure which holds device
specific attributes. Instead of runtime decisions "if (is212())" we set
callbacks/attributes while device detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the current lowlevel spi calls for the detect device
function instead we handle this via regmap. Also put the detection of
in a seperate function and set all device specific attributes while detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds regmap support for the at86rf230 driver and drop the
lowlevel spi access functions and use the regmap access functions.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".
This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-02
This series contains updates to i40e and i40evf.
Anjali fixes a possible race where we were trying to free the dummy packet
buffer in the function that created it, so cleanup the dummy packet buffer
in i40e_clean_tx_ring() instead. Also fixes an issue where the filter
program routine was not checking if there were descriptors available for
programming a filter.
Mitch fixes unnecessary delays when sending the admin queue commands by
moving a declaration up one level so we do not dereference it out of scope.
Fixes an issue with the VF where if the admin queue interrupts get lost for
some reason, the VF communication will stall as the VFs have no way of
reaching the PF. To alleviate this condition, go ahead and check the ARQ
every time we run the service task. Updates i40evf to allow the watchdog
to fire vector 0 via software, which makes the driver tolerant of dropped
interrupts on that vector.
Paul fixes a shifted '1' to be unsigned to avoid shifting a signed integer.
Jesse disables TPH by default since it is currently not enabled in the
current hardware. Also finishes the i40e implementation of get_settings
for ethtool.
Catherine adds a new variable (hw.phy.link_info.an_enabled) to track whether
auto-negotiation is enabled, along with the functionality to update the
variable. Adds the functionality to set the requested flow control mode.
Adds i40e implementation of setpauseparam and set_settings to ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which
is an invalid assumption. Fix this by implementing a common error
cleanup path, and use it to also clean up after failed bounce buffer
allocation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not double-free any allocations, and that any transmit
skbuffs are properly freed when we clean up the rings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid writing any state until we're certain we can proceed with the
transmission: this avoids writing mapping error address values to the
descriptors, or setting the skbuff pointer until we have successfully
mapped the skb.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb. When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.
This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.
This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.
Therefore, this variable serves no purpose, so let's remove it.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the network interface goes down, stop the phy to prevent further
link up status changes before taking the MAC or netif sections down.
This prevents further reception of link up events which could
potentially call fec_restart().
Since phy_stop() takes the mutex which adjust_link() runs under, we
also ensure that adjust_link() will not already be processing a link
up event.
We also need to do this when suspending as well - we don't want a
mis-timed phy state change to restart the MAC after we have stopped
it for suspend, and thus need to restart the phy when resuming.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disconnect from a phy, we should forget our pointer to it so we
don't accidentally try to configure it. We handle a NULL phy pointer
correctly in most places, except fec_enet_set_pauseparam(). Fix this
too.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fep->phy_dev can not be NULL here for two reasons:
- fec_enet_open() will have successfully connected the phy, or will have
failed.
- fec_enet_open() will have called phy_start(fep->phy_dev), which
unconditionally dereferences this pointer.
If it were to be NULL here, then fec_enet_open() will have already
oopsed.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use netif_stop_queue() in several places where we want to ensure that
the start_xmit function is not running. netif_stop_queue() is not
sufficient to achieve that - it merely sets a flag to indicate that the
transmit queue(s) should not be run.
netif_tx_disable() gives this guarantee, since it takes the transmit
queue lock while marking the queue stopped. This will wait for the
transmit function to complete before returning.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts
are regularly reported. With the tx ring dumping in place, we can see
that all entries are in use, and the hardware has finished transmitting
these packets. However, the driver has not reclaimed these ring
entries.
This can occur if the interrupt handler is invoked at the wrong moment -
eg:
CPU0 CPU1
fec_enet_tx()
interrupt, IEVENT = FEC_ENET_TXF
FEC_ENET_TXF cleared
napi_schedule_prep()
napi_complete()
The result is that we clear the transmit interrupt, but we don't trigger
any cleaning of the transmit ring. Instead, use a different strategy:
- When receiving a transmit or receive interrupt, disable both tx and rx
interrupts, but do not acknowledge them. Schedule a napi poll. Don't
loop.
- When we are polled, read IEVENT, acknowledging the pending transmit
and receive interrupts, before then going on to process the
appropriate rings.
This allows us to avoid the race, and has a number of other advantages:
- we cut down on the number of transmit interrupts we have to process.
- we only look at the rings which have pending events.
- we gain additional throughput: the iperf total bandwidth increases
from about 180Mbps to 240Mbps:
[ 3] 0.0-10.0 sec 68.1 MBytes 57.0 Mbits/sec
[ 5] 0.0-10.0 sec 72.4 MBytes 60.5 Mbits/sec
[ 4] 0.0-10.1 sec 76.1 MBytes 63.5 Mbits/sec
[ 6] 0.0-10.1 sec 71.9 MBytes 59.9 Mbits/sec
[SUM] 0.0-10.1 sec 288 MBytes 241 Mbits/sec
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the pause parameters causes a running network interface to be
restarted. However, the restart forces the FEC into half-duplex mode,
whether or not the remote end is in half-duplex mode. Misconfigured
duplex mode is a known source of problems on a link.
Fix this by always preserving the duplex mode on configuration changes.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iMX6 gigabit FEC does not support half-duplex gigabit operation.
Phys attacked to the FEC may support this, and we currently do nothing
to disable this feature. This may result in an invalid configuration.
Mask out phy support for gigabit half-duplex operation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:
- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us
The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This boolean tells us whether we are using the RXCHK hardware block,
so use a variable name that reflects that. RXCHK might be used in the
future to implement Wake-on-LAN using ARP or unicast packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware recommended suspend/resume procedure for
SYSTEMPORT. We leverage the previous factoring work such that we can
logically break all suspend/resume operations into disctint RX and TX
code paths.
When the system enters S3, we will loose all register contents, so
make sure that we correctly re-program all the hardware and software
views of the RX & TX rings as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor common code that either enables or disables the network
interface with the networking stack. We are going to reuse these
functions for suspend/resume callbacks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite often we need to enable either the transmitter or the receiver
bits in UMAC_CMD, use umac_enable_set() to do that for us.
This is a preliminary change to introduce suspend/resume support in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using internal 10 Mbps PHY, isolate the external PHY from MII bus.
External PHY must be kept powered up because it passes TX from tlan chip to
network.
This fixes weird link-loss problems under load with OC-2326 card at 10 Mbps.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
