Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add two port-command helpers to handle the UART module-id parameter
instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the vendor-request helpers data parameters be void pointers and
drop the caller casts.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it
and use the __packed macro consistently.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use kernel types consistently by replacing the remaining __uXX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a read-port-command helper analogous to the send-port-command
helper to take care of the UART module id instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a send-port-command helper which takes care of determining the UART
module id when sending commands instead of doing so at every call site.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the vendor-request helpers by using kernel-types consistently
and using void pointers for the data arguments, which allows removing
a cast from one caller.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Unlike the TUSB5052, the TUSB3410 has an LSR TEMT bit to tell if both
the transmitter data and shift registers are empty.
Make sure to check also the shift register on TUSB3410 when waiting for
the transmit buffer to drain during close and drop the time-based
one-char delay which is otherwise needed (e.g. 90 ms at 110 bps).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The three-character drain delay was added by commit f1175daa53 ("USB:
ti_usb_3410_5052: kill custom closing_wait") when removing the custom
closing-wait implementation, which used a fixed 20 ms poll period and
drain delay.
This was likely a bit too conservative as a one-character timeout (e.g.
33 ms at 300 bps) should be enough to compensate for the lack of a
transmitter empty bit in the TUSB5052 line-status register.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Document that the device line-status register doesn't tell when the
transmitter shift register has emptied and that this is why the
one-character drain delay is needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The f81232 driver now waits for the transmit FIFO to drain during close
so there is no need to keep the time-based drain delay, which would add
up to two seconds on every close for low line speeds.
Fixes: 98405f8103 ("USB: serial: f81232: add tx_empty function")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a debug printk to dump the GPIO configuration stored in EEPROM
during probe.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new GPIO valid-mask feature to inform gpiolib which pins are
available for use instead of handling that in a request callback.
This also allows user space to figure out which pins are available
through the chardev interface without having to request each pin in
turn.
Note that the return value when requesting an unavailable pin will now
be -EINVAL instead of -ENODEV.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the port struct device rather than tty class device for debugging.
Note that while USB serial doesn't support serdev yet (due to serdev not
handling hotplugging), serdev ttys do not have a corresponding class
device and would have been logged using a "(NULL device *):" prefix.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unused definitions relating to a never mainlined custom
proc-interface and some likewise unused string descriptor definitions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Switch to using the system-wide default 30-second closing-wait timeout
instead of the driver specific 40-second timeout.
The timeout can be changed per port using TIOCSSERIAL (setserial) if
needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The ti_usb_3410_5052 has supported changing the closing_wait parameter
through TIOCSSERIAL (setserial) for about a decade and commit
f1175daa53 ("USB: ti_usb_3410_5052: kill custom closing_wait").
It's time to drop the corresponding driver-specific module parameter.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Switch to using the system-wide default 30-second closing-wait timeout
instead of the driver specific 40-second timeout.
The timeout can be changed per port using TIOCSSERIAL (setserial) if
needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that all USB serial drivers supports setting the closing_wait
parameter through TIOCSSERIAL (setserial) it's time to drop the
corresponding io_ti module parameter.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCSSERIAL implementation needs to compare the old flag and divisor
settings with the new to detect ASYNC_SPD changes, but there's no need
to copy all driver state to the stack for that.
While at it, unbreak the function parameter list.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the deprecated custom_divisor field is an unprivileged
operation so after verifying that flag field does not contain any
privileged changes both updates can be carried out by any user.
Combine the two branches and drop the erroneous comment.
Note that private flags field is only used for ASYNC flags so there's no
need to try to retain any other bits when updating the flags.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCSSERIAL error handling is inconsistent at best, but drivers tend
to ignore requests to change parameters which cannot be changed rather
than return an error.
The FTDI driver ignores change requests for all immutable parameters but
baud_base so return success also in this case for consistency.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The TIOCGSERIAL ioctl can be used to set and retrieve the UART type for
legacy UARTs, but some USB serial drivers have been reporting back
random types in order to "make user-space happy".
Some applications have historically expected TIOCGSERIAL to be
implemented, but judging from the Debian sources, the port type not
being PORT_UNKNOWN is only used to check for the existence of legacy
serial ports (ttySn).
Drivers like ftdi_sio have been using PORT_UNKNOWN for twenty years (and
option for 10 years) without anyone complaining so let's stop reporting
back anything else.
In the unlikely event that this do cause problems, this should be fixed
tree-wide anyway (e.g. for all USB serial drivers and also CDC-ACM).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The closing_wait parameter determines how long to wait for the transfer
buffers to drain during close and the default timeout of 30 seconds may
not be sufficient at low line speeds. In other cases, when for example
flow is stopped, the default timeout may instead be too long.
Add generic support for TIOCSSERIAL and TIOCGSERIAL with handling of the
three common parameters close_delay, closing_wait and line for the
benefit of all USB serial drivers while still allowing drivers to
implement further functionality through the existing callbacks.
This currently includes a few drivers that report their base baud clock
rate even if that is really only of interest when setting custom
divisors through the deprecated ASYNC_SPD_CUST interface; an interface
which only the FTDI driver actually implements.
Some drivers have also been reporting back a fake UART type, something
which should no longer be needed and will be dropped by a follow-on
patch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Fix up the TIOCMGET, TIOCMSET and TIOCGICOUNT helpers which returned
-EINVAL when a USB serial driver did not implement the corresponding
methods.
Note that the TIOCMGET and TIOCMSET helpers predate git and do not get a
corresponding Fixes tag below.
Fixes: d281da7ff6 ("tty: Make tiocgicount a handler")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The baud_base parameter could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
Fix the usb_wwan TIOCGSERIAL implementation by dropping its custom
interpretation of the unused port and baud_base fields, which were set
to the port index and current line speed, respectively.
Fixes: 02303f7337 ("usb-wwan: implement TIOCGSERIAL and TIOCSSERIAL to avoid blocking close(2)")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the usb_wwan implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: 02303f7337 ("usb-wwan: implement TIOCGSERIAL and TIOCSSERIAL to avoid blocking close(2)")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The port close_delay and closing_wait parameters set by TIOCSSERIAL are
specified in jiffies and not milliseconds.
Add the missing conversions so that the TIOCSSERIAL works as expected
also when HZ is not 1000.
Fixes: 02303f7337 ("usb-wwan: implement TIOCGSERIAL and TIOCSSERIAL to avoid blocking close(2)")
Cc: stable@vger.kernel.org # 2.6.38
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the port closing-wait parameter is a privileged operation so
make sure to return -EPERM if a regular user tries to change it.
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
close_delay, but let's report back the default value actually used (0.5
seconds).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: 52af954599 ("USB: add USB serial ssu100 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The baud_base parameter could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: faac64ad9c ("USB: serial: opticon: add serial line ioctls")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing close_delay, but let's report back the default value actually
used (0.5 seconds).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the uart base clock when it
could not be detected, but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds (not jiffies). The driver does not yet support
changing these, but let's report back the default values actually used
(0.5 and 30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The FTDI driver is the only USB serial driver supporting the deprecated
ASYNC_SPD flags, which are reported back as they should by TIOCGSERIAL,
but the returned parameters did not include the line number.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Fixes: aac1fc386f ("USB: serial: add Fintek F81232 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Fixes: aac1fc386f ("USB: serial: add Fintek F81232 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The port parameter is used to set the I/O port and does not make any
sense to use for USB serial devices.
The baud_base parameter could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The close_delay and closing_wait parameters returned by TIOCGSERIAL are
specified in centiseconds. The driver does not yet support changing
these, but let's report back the default values actually used (0.5 and
30 seconds, respectively).
Fixes: 2f430b4bba ("USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl calls.")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new multi-interface support in USB serial core to properly claim
also the control interface during probe. This prevents having another
driver claim the control interface and makes core allocate resources
also for the interrupt endpoint (currently unused).
Switch to probing only Communication Class interfaces and use the Union
functional descriptor to determine the corresponding data interface.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A single USB function can be implemented using a group of interfaces and
this is for example commonly used for Communication Class devices.
Add support for multi-interface functions to USB serial core and export
an interface that allows drivers to claim a second sibling interface.
The interface could easily be extended to allow claiming further
interfaces if ever needed.
When a driver claims a sibling interface in probe(), core allocates
resources for any bulk in, bulk out, interrupt in and interrupt out
endpoints found also on the sibling interface.
Disconnect is implemented so that unbinding either interface will
release the other interface while disconnect() is called precisely once.
Similarly, suspend() is called when the first sibling interface is
suspended and resume() is called when the last sibling interface is
resumed by USB core.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Refactor endpoint classification and replace the build-time
endpoint-array sanity checks with runtime checks in preparation for
handling endpoints from a sibling interface.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The suspending flag was added back in 2009 but no users ever followed.
Remove it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
