When decoding using the CODA internal rotator (for example NV12
capture), currently the value vb2_buf.index + CODA_MAX_FRAMEBUFFERS (19)
is written into the DEC_PIC_ROT_INDEX register. At least with firmware
version 3.1.1 this causes CODA hangups as soon as the register value
reaches 32. Instead, always write CODA_MAX_FRAMEBUFFERS.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Both platform_get_irq_byname() and platform_get_irq() already print an
error. Remove the redundant error message.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds JPEG encoding support for CODA960, handling the JPEG
hardware directly. A separate JPEG encoder video device is created due
to the separate hardware unit and different supported pixel formats.
While the hardware can not change subsampling on the fly, it can encode
4:2:2 subsampled images into JPEGs of the same subsampling.
There are two additional tracepoints added to the coda driver that can
be used together with the v4l2:v4l2_qbuf and v4l2:v4l2_dqbuf tracepoints
to to follow video frames through the mem2mem device when encoding or
decoding with the CODA960 JPEG codec:
coda:coda_jpeg_run
coda:coda_jpeg_done
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
[hverkuil-cisco@xs4all.nl: removed unused k and q_data_dst variables]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CODA960 JPEG codec is controlled directly from the host, there is no
support in the BIT processor firmware. This patch adds the necessary
register definitions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Huffman bits tables are always 16 bytes long, and they are always
followed directly by the values tables, both in hardware and in JPEG
files. Just merge the two tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Always call finish_run when the hardware signals completion. This
will allow JPEG contexts to clean up even if job_abort was called
during the device_run.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Disable output side crop selections for the decoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1576): IS_DECODER(node)
test Cropping: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Disable capture side compose selections for the encoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1662): IS_ENCODER(node)
test Composing: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The irqlock spinlock has been unused from the start. Remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The kernel driver never touches the decoded buffers with the CPU.
All accesses are either done by hardware DMA masters or userspace
mapping the buffers. This means we don't need a kernel virtual
address mapping for those buffers at all. As those buffers are
usually quite large, we can save a good deal of kernel vmalloc
space by requesting to not have a kernel mapping set up for them.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The BIT decoder picture run temporarily locks the bitstream mutex while
the coda device mutex is locked, to refill the bitstream ring buffer.
Consequently, the decoder start command, which locks both mutexes when
flushing the bitstream ring buffer, must lock the coda device mutex
first as well, to avoid an ABBA deadlock.
Fixes: e7fd95849b ("media: coda: flush bitstream ring buffer on decoder restart")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for dynamically changing the GOP size, bitrate, frame rate,
constant intra quantization parameter, number of intra refresh macro
blocks and slice mode parameters.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changing slice mode dynamically while encoding will require to calculate
the register value again, so split it out into a separate function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the platform device pointer is stored in struct coda_dev,
only to convert it into a device pointer wherever it is used. Just
store the device pointer directly.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If reordering is not enabled, the last decoded frame has to be the last
returned buffer. Otherwise wait for the firmware to report no more
frame to display. In that case the return buffer is the last one as
well, and can be reported as such.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there is still a buffer pending, mark it as the last buffer. It will
create a meta that is flagged as last when the buffer is copied into the
bitstream ring buffer. If there are no more buffers pending, find the
last bitstream meta and mark it as last. If there is no bitstream meta
either, wake up the capture queue as there will be no more decoded
frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure that an encoder stop command running concurrently with an
encoder finish_run always either flags the last returned buffer or wakes
up the capture queue to signal the end of stream condition afterwards.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the flagged last output buffer to also flag the corresponding
capture buffer after encoding. This causes the end of stream event
to be issued and the buffer to be dequeued with the last flag set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are no pending queued output buffers to be encoded, waking up
the capture queue with -EPIPE signals end of stream. If there are
pending buffers on the other hand, setting the V4L2_BUF_FLAG_LAST on
the resulting encoded capture buffers is all that is needed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using the output queue sequence counter to determine the last buffer to
be encoded or decoded always was fragile at best. Now that we have the
last buffer flag propagating from the output queue to the capture queue
correctly, this is not needed anymore.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be encoded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are still queued output buffers pending to be copied into the
bitstream ring buffer, setting the stream end flag should be deferred
until the marked last output buffer is written into the bitstream ring
buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be decoded and only copy pending queued
output buffers into the bitstream ring buffer in the BIT processor
decoder case.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since V4L2_BUF_FLAG_LAST is a CAPTURE only flag, clear it from OUTPUT
buffers in QBUF and DQBUF. This allows to use the flag internally to
signal the last buffer to decode after a decoder stop command was
issued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If no more frames are decoded in bitstream end mode, and a previously
decoded frame has been returned, the firmware still increments the frame
number. To avoid a sequence number mismatch after decoder restart,
increment the sequence_offset correction parameter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bitstream ringbuffer might be in an underrun state after draining,
or it might still contain unread data if the previous decoder stop
command was flagged as immediate. Flush the bitstream ring buffer
during V4L2_DEC_CMD_START to get into a well defined state. Also fill
the bitstream with buffers that have been queued during draining,
to resume decoding immediately.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On CODA960, sequence initialization can succeed if less than 512 bytes
are ready in the bitstream ring buffer.
On other variants, warn about too small payload in start_streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the first buffer contains only headers, the sequence initialization
command fails. On CodaHx4 the buffer must be padded to at least 512
bytes, on CODA960 it seems to be enough to just repeat the sequence and
extension headers (MPEG-2) or the VOS and VO headers (MPEG-4) once for
for sequence initialization to succeed without further bitstream data.
On CodaHx4 the headers can be repeated multiple times until the 512 byte
mark is reached.
A similar issue was solved for h.264 by padding with a filler NAL in
commit 0eef89403e ("[media] coda: pad first h.264 buffer to 512
bytes").
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pass vaddr and size to coda_bitstream_queue instead of a struct
vb2_v4l2_buffer to make it reusable for queueing data that is
not exactly a whole v4l2 buffer into the bitstream ringbuffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine the separate auxiliary buffer, buffer meta, frame type, and
decode error arrays into an array of struct coda_internal_frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful decoder API requires decoders to signal detection
of stream dimensions via the V4L2_EVENT_SOURCE_CHANGE event.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a sequence initialization work item to be run when OUTPUT buffers
are queued in the initialization state.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sequence initialization already has to happen during the
initialization phase, after headers have been queued on the OUTPUT
queue. This means that sequence initialization has to be queued as
a work item from QBUF on the OUTPUT queue. The internal framebuffer
setup should be done later during VIDIOC_REQBUFS() on the CAPTURE
queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the DEC_CMD_STOP command is issued after the context has already
consumed all the queued buffers, we need to make sure to wake the
destination queue with last_buffer_dequeued set, to allow userspace to
make progress in its EOS handling.
As there might still be picture run workers pending at that point, we
need to synchronize with them, so the sequence number comparison reads
stable values.
reword commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine setting the last_buffer_dequeued flag on the capture video
queue and waking up its done workqueue into a helper function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
coda_encoder_cmd() is racy, as the last scheduled picture run worker can
still be in-flight while the ENC_CMD_STOP command is issued. Depending
on the exact timing the sequence numbers might already be changed, but
the last buffer might not have been put on the destination queue yet.
In this case the current implementation would prematurely wake the
destination queue with last_buffer_dequeued=true, causing userspace to
call streamoff before the last buffer is handled.
Close this race window by synchronizing with the pic_run_worker before
doing the sequence check.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[l.stach@pengutronix.de: switch to flush_work, reword commit message]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sequence number handling assumed that the BIT processor frame number
starts counting at 1, but this is not true for the MPEG-2 decoder,
which starts at 0. Fix the sequence counter offset detection to handle
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use mem2mem try_en/decoder_cmd helpers to ensure consistent behaviour
with other video codec drivers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CMD_START shall be used to start the processing after a drain that
was initiated with CMD_STOP.
Up until now, a drain on coda could only be finished with a
STREAMOFF-STREAMON, which resulted in a reset of the device.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When building with CONFIG_VIDEO_CODA and CONFIG_CODA_FS enabled as
loadable modules, we see the following warning:
fs/coda/coda.ko
drivers/media/platform/coda/coda.ko
Rework so media/platform/coda is named coda-vpu. Leaving CODA_FS as is
since that's a well known module.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into media/master
There are some conflicts due to SPDX changes. We also have more
patches being merged via media tree touching them.
So, let's merge back from upstream and address those.
Linux 5.2-rc4
* tag 'v5.2-rc4': (767 commits)
Linux 5.2-rc4
MAINTAINERS: Karthikeyan Ramasubramanian is MIA
i2c: xiic: Add max_read_len quirk
lockref: Limit number of cmpxchg loop retries
uaccess: add noop untagged_addr definition
x86/insn-eval: Fix use-after-free access to LDT entry
kbuild: use more portable 'command -v' for cc-cross-prefix
s390/unwind: correct stack switching during unwind
block, bfq: add weight symlink to the bfq.weight cgroup parameter
cgroup: let a symlink too be created with a cftype file
drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
drm/nouveau/secboot: split out FW version-specific LS function pointers
drm/nouveau/secboot: pass max supported FW version to LS load funcs
drm/nouveau/core: support versioned firmware loading
drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
block: free sched's request pool in blk_cleanup_queue
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use v4l2_m2m2_buf_copy_metadata to let BIT encoder contexts copy buffer
field, timestamp, timestamp flags, and optionally timecode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
coda_command_sync, coda_hw_reset, and __coda_start_decoding
all expect to be called under the coda_mutex device lock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The MPEG-2 decoder firmware reports profile and level indication that
can be used to set V4L2 MPEG-2 profile and level controls
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The MPEG-4 decoder firmware reports profile and level indication values
that can be used to update V4L2 MPEG-4 profile and level controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
