Call pci_read_irq() for bridges too, so that the pin value
is stored for bridges that require interrupts.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the stored value of the interrupt pin rather than try to read
the config again.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the stored value of the Interrupt Pin, rather than try to read
it again.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Store the value of the INTERRUPT_PIN in the pci_dev structure
so that it can be retrieved later.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a major update to the cyblafb framebuffer driver. Most
of the stuff has been tested in the mm tree.
Main advantages:
============
- vxres > xres support
- ywrap and xpan support
- much faster for almost all modes (e.g. 1280x1024-16bpp
draws more than 41 full screens of text instead of about 25
full screens of text per second on authors Epia 5000)
- module init/exit code fixed
- bugs triggered by console rotation fixed
- lots of minor improvements
- startup modes suitable for high performance scrolling
in all directions
This diff also contains a lot of white space fixes.
No side effects are possible, only one single graphics core is affected.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__rcu_pending() is rather fat and called twice from rcu_pending().
rcu_pending() has multiple callers, and not that small too.
This patch uninlines both of them.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows ipw2100 driver to advertise the WPA-related encryption
options that it does really support. It's necessary to work correctly
with NetworkManager and other programs that actually check driver & card
capabilities.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These warnings are emitted if non-modular network drivers are built.
Fixes just move cleanup_card() definitions into #ifdef MODULE region.
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/wd.c:131: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/3c503.c:152: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ne.c:216: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp.c:106: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp-plus.c:142: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/smc-ultra.c:172: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/e2100.c:144: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/es3210.c:159: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lne390.c:149: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lance.c:313: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ac3200.c:127: warning: 'cleanup_card' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This contains a bug fix for large buffers. Originally, if a tx buffer to
be sent was larger then the maximum size of the tx descriptor, it would
overwrite other control bits. In this patch, the buffer is split over
multiple descriptors. Also, the fragments are now setup in forward order.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove bouncing mail address of mv643xx maintainer.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix an invalid memory reference in the e1000 driver which would cause
kernel panic.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Jeb Cramer <cramerj@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
"extern inline" doesn't make much sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
"extern inline" doesn't make much sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes a wrong indentation.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MIPS dependency for dm9000 ethernet controller. Indeed this controller
is used by some embedded platforms based on MIPS CPUs.
Signed-off-by: Franck Bui-Huu <franck.bui@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ifenslave, as of abi version 2, does not set the ip address on the slave
interfaces. The documentation example however still shows that the
ensalved interfaces should have the same IP as the master. The patch
simply removes the lines from the example which should no longer appear.
Signed-off-by: Eric Paris <eparis@redhat.com>
bonding.txt | 2 --
1 files changed, 2 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A BIOS bug affecting some multiport tulip NICs requires an irq fixup
in tulip_core.c. This has only been enabled for i686, but it is
needed for x86_64 as well.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch works around a problem with spurious interrupts seen at boot time when
a MAXTOR 6H500F0 drive is present. An ATA interrupt condition is mysteriously
present at start of day. If we took too long in issuing the first command,
the kernel would basically get tired of the spurious interrupts and turn the interrupt
off. Issuing the first command essentially causes the interrupt condition to
get acknowledged.
I haven't seen this happen with any other drives.
What I basically do is ack ATA status by reading it regardless of whether we're
expecting to have to handle an interrupt. This clears the start-of-day anomalous
interrupt condition, and keeps the kernel from disabling that interrupt due to
too many spurious interrupts.
Also, I fixed a bug where hotplug interrupts weren't getting acknowledged as handled
in the ISR. This was not the cause of the spurious interrupts, but it's the right
thing to do anyway.
Signed-Off-By: Andrew Chew
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Disable TX status deferral (EMACx_MR[MWSW=001]) in half-duplex mode.
I have two reports when EMAC stops transmitting when connected to a
hub. TX ring debug printouts show complete mess when this happens,
probably hardware collision handling doesn't work quite well in this
mode.
This is relevant only for SoCs with EMAC4 core (440GX, 440SP, 440SPe).
Tested on 440GX.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes some of the ieee80211 crypto related code so that
instead of having the host fully do crypto operations, the host_build_iv
flag works properly (for WEP in this patch) which, if turned on,
requires the hardware to do all crypto operations, but the ieee80211
layer builds the IV. The hardware also has to build the ICV.
Previously, the host_build_iv flag couldn't be used at all for WEP, and
not alone (with both host_decrypt and host_encrypt disabled) because the
crypto algorithm wasn't assigned. This is also fixed.
I have tested this patch both in host crypto mode and in hw crypto mode
(with the Broadcom chipset).
[resent, signing digitally caused it to be MIME-junked, sorry]
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't enable the pci device twice (already done in the probe
routine). Propogate the error codes from pci_request_region
back to initial probing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sk98lin driver doesn't do proper error number handling
during initialization. Note: -EAGAIN is a bogus return value for
hardware errors.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sk98lin driver error recovery on two port boards is bad.
If it fails the second allocation, it will not release resources
properly. Also it registers the second port in the pci driver data
If second port fails, might as well go with one port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sk98lin 64bit memory handling is wrong. It doesn't set the
highdma flag; i.e. the kernel always does bounce buffers.
It doesn't fallback to 32 bit mask if it can't get 64 bit mask.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sk98lin driver has a routine marked __init that is called from
the probe code. If using pci hotplug, this could be called after
the initialization so it needs to be marked __devinit.
So if you hot added a sk98lin board, the kernel would crash.
I don't have hot plug hardware to actually try this feat.
Also, there are two routines, only called from SkGeBoardInit that can
be marked __devinit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes IDE use the new blk_complete_request() interface.
There's still room for improvement, as __ide_end_request() really
could drop the lock after getting HWGROUP->rq (why does it need to
hold it in the first place? If ->rq access isn't serialized, we are
screwed anyways).
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch moves the SCSI softirq handling to the block layer version.
There should be no functional changes.
Signed-off-by: Jens Axboe <axboe@suse.de>
Request completion can be a quite heavy process, since it needs to
iterate through the entire request and complete the bio's it holds.
This patch adds blk_complete_request() which moves this processing
into a dedicated block softirq.
Signed-off-by: Jens Axboe <axboe@suse.de>
It's a broken interface, it's done way too late. And apparently it triggers
slab problems in recent kernels as well (most likely after the generic dispatch
code was merged). So kill it, ide-cd is the only user of it.
Signed-off-by: Jens Axboe <axboe@suse.de>
For SG_IO requests, bio->bi_bdev may not be explicitly initialized. So make
bio_init() clear the field to make sure it's always NULL or valid.
Signed-off-by: Jens Axboe <axboe@suse.de>
We don't set CONFIG_PPC_MULTIPLATFORM on iSeries (yet). Avoid
compiling in the prom_init stuff on iSeries.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In add_memory() we should be using __va() to get a virtual address.
Spotted by Mike Kravetz.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The CONFIG_PPC_OF symbol is used to mean that the firmware device tree
access functions are available. Since we always have a device tree
with ARCH=powerpc, make CONFIG_PPC_OF always Y for ARCH=powerpc.
This fixes some compile errors reported by Kumar Gala, but in a
different way to his patch. This also makes prom_parse.o be compiled
only if CONFIG_PPC_OF so that non-OF ARCH=ppc platforms will compile.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When taking a DABR exception we were reporting the PC. It makes more
sense to report the address that caused the exception, and the gdb guys
would like it that way.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
POWER5+ adds new PMU groups and as such needs to be treated differently
by oprofile userspace. Change it to report itself as power5+.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My recent changes to oprofile broke it when built as a module. Fix it by
using an enum instead of a function pointer. This way we still retain
the oprofile configuration in the cputable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
