hid_parser is non-trivially large structure, so it should be allocated
using vmalloc() to avoid unsuccessful allocations when memory fragmentation
is too high.
This structue has a very short life, it's destroyed as soon as the report
descriptor has been completely parsed.
This should be considered a temporary solution, until the hid_parser is
rewritten to consume less memory during report descriptor parsing.
Acked-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit d2487cb425.
Russell King points out that it's obviously bogus, and I have to agree.
Not only does "irq" not even exist in that scope, but we obviously need
to free the irq that we actually requested, and that's IRQ_USB.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>,
Cc: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits)
USB Elan FTDI: check for workqueue creation
USB: fix spinlock recursion in cdc-acm.c
USB: fix Unaligned access in EHCI driver
USB: Product ID for FT232RL in ftdi_sio
USBNET: DM9501: Add Corega FEther USB-TXC support.
USB: ipaq.c: Additional devices
USB: further fix for usb-serial
USB: fix usb-serial device naming bug
USB: RTS/DTR signal patch for airprime driver
USB: ftdi_sio: use port_probe / port_remove thereby fixing access to the latency_timer
usb-serial: fix shutdown / device_unregister order
USB: add Additional PIDs in ftdi_sio
USB: add QL355P power supply ids to fdti_sio
USB: New device IDs for cp2101 driver
USB: kill dead code from hub.c
USB: ratelimit debounce error messages
USB: pxa2xx_udc: fix hardcoded irq number
UHCI: fix port resume problem
USB: set the correct interval for interrupt URBs
USB: goku_udc: Remove crude cache coherency code
...
Delay the read of the EC status register until
after the event that caused it occurs -- otherwise
it is possible to read and act on stale status that was
associated with the previous event.
Do this with a perpetually incrementing "event_count" to detect
when a new event occurs and it is safe to read status.
There is no workaround for polling mode -- it is inherently
exposed to reading and acting on stale status, since it
doesn't have an interrupt to tell it the event completed.
http://bugzilla.kernel.org/show_bug.cgi?id=8110
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]
Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
>
> 34ef50e5b1 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.
This patch should fix the issue.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:
Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem. Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.
With the attached patch, the RTS/DTR lines are resetted on a close. The
code was mainly taken from the option.c driver.
Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
I use the FTDI VID 0x0403. My PID's are:
0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device
The company is "IBS Ing.-Buero Schleusener".
From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here are two new device IDs for the cp2101 driver.
The diff is with linus's tree as of this evending.
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flaky hardware can cause a lot of debounce failed messages. To limit
the performance impact, a ratelimit should be used.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes last use of hardcoded number of irq to
use platfrom_get_irq.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller. The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as862) fixes a couple of bugs in the way usbcore handles
intervals for interrupt URBs. usb_interrupt_msg (and usb_bulk_msg for
backward compatibility) don't set the interval correctly for
high-speed devices. proc_do_submiturb() doesn't set it correctly when
a bulk URB is submitted to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is deep architecture specific magic and does should not to exist
in a driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an usual_devs entry for the Nokia 6288. Originally from
Andrew with a re-diff by Phil.
From: Andrew Nayenko <relan@bk.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the duplicate supertop entries that made it into the
.21 rc kernels.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename the driver struct used with at91_udc to prevent yet another
bogus warning from "modpost".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct some of the most obvious spelling and grammar
mistakes in drivers/acpi/video.c (comments and printk output).
Signed-off-by: Julius Volz <juliusrv@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
IMHO, ACPI disabled due to DMI failure or blacklisted year should be noted,
as is done with other ACPI blacklisting.
This will help people troubleshoot when ACPI isn't working. Status quo is
a mysterious "ACPI Disabled" message without explanation on BIOS that
implements ACPI but not DMI. This is actually fairly common on embedded
x86 boards.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
User supplied len < 0 can cause leak of kernel memory.
Use unsigned compare instead.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/pci/search.c caused following section mismatch warning
(if compiled with CONFIG_HOTPLUG=n):
WARNING: drivers/pci/built-in.o - Section mismatch: reference to .init.text: from .text.pci_find_bus after 'pci_find_bus' (at offset 0x24)
This was due to pci_find_bus() calling a function marked __devinit.
Fix was to remove the __devinit from the offending function.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix following section mismatch warning (when compiled with CONFIG_HOTPLUG=n):
WARNING: drivers/pci/built-in.o - Section mismatch: reference to .init.text:aer_probe from .data between 'aerdrv' (at offset 0x1608) and 'aer_error_handlers'
Warning was fixed by renaming aerdrv to aerdriver so we pass the whitelist.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix following section mismatch warning (when compiled with CONFIG_HOTPLUG=n):
WARNING: drivers/pci/built-in.o - Section mismatch: reference to .init.text:pcie_portdrv_probe from .data between 'pcie_portdrv' (at offset 0xe40) and 'pcie_portdrv_err_handler'
This warning was fixed by renaming pcie_portdrv to pcie_portdriver so we pass
the whitelist.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sanity check in pcim_pin_device() was too restrictive in that it didn't
allow multiple calls to the function, which is against the devres
philosohpy of fire-and-forget. Track pinned status separately and allow
pinning multiple times.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>