I've spent quite a bit of time poking at this driver and it's used on
several Chromebooks I'm involved with. I'd like to get notified about
patches. Add myself as a reviewer. It's expected that changes will
still be landed through drm-misc as they always have been.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308110615.2.I4485769d5b25a8096508e839b8fea12ce7b836d3@changeid
The bindings for bridge chips should also get the same maintainers
entry so the right people get notified about bindings changes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308110615.1.I1f1b10daf7361feb6705f789deb680b8d7720de9@changeid
The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".
Switch to the new function and reduce boilerplate.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221072835.10032-1-jose.exposito89@gmail.com
Currently the ssd130x driver only sets the segment remap setting when
the device tree requests it; it however does not clear the setting if
it is not requested. This leads to the setting incorrectly persisting
if the hardware is always on and has no reset GPIO wired. This might
happen when a developer is trying to find the correct settings for an
unknown module, and cause the developer to get confused because the
settings from the device tree are not consistently applied.
Make the driver apply the segment remap setting consistently, setting
the value correctly based on the device tree setting. This also makes
this setting's behavior consistent with the other settings, which are
always applied.
Fixes: a61732e808 ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308160758.26060-2-wens@kernel.org
The SSD130x's command to toggle COM scan direction uses bit 3 and only
bit 3 to set the direction of the scanout. The driver has an incorrect
GENMASK(3, 2), causing the setting to be set on bit 2, rendering it
ineffective.
Fix the mask to only bit 3, so that the requested setting is applied
correctly.
Fixes: a61732e808 ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308160758.26060-1-wens@kernel.org
The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".
Switch to the new function and reduce boilerplate.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228183955.25508-1-jose.exposito89@gmail.com
Clang static analysis reports this issue
anx7625.c:876:13: warning: The left operand of '&' is
a garbage value
if (!(bcap & 0xOA01)) {
~~~~ ^
bcap is only set by a successful call to
anx7625_aux_trans(). So check.
Fixes: cd1637c7e4 ("drm/bridge: anx7625: add HDCP support")
Signed-off-by: Tom Rix <trix@redhat.com>
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303201943.501746-1-trix@redhat.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
This device requires the packets on lanes aligned at the end to fix
screen shift or scroll.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-4-rex-bc.chen@mediatek.com
Some DSI RX devices (for example, anx7625) require last alignment of
packets on all lanes after each row of data is sent.
Otherwise, there will be some issues of shift or scroll for screen.
Take horizontal_sync_active_byte for a example,
we roundup the HSA packet data to lane number, and the subtraction of 2
is the packet data value added by the roundup operation, making the
long packets are integer multiples of lane number.
This value (2) varies with the lane number, and that is the reason we
do this operation when the lane number is 4.
In the previous operation of function "mtk_dsi_config_vdo_timing",
the length of HSA and HFP data packets has been adjusted to an
integration multiple of lane number.
Since the number of RGB data packets cannot be guaranteed to be an
integer multiple of lane number, we modify the data packet length of
HBP so that the number of HBP + RGB is equal to the lane number.
So after sending a line of data (HSA + HBP + RGB + HFP), the data
lanes are aligned.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-3-rex-bc.chen@mediatek.com
Since a HS transmission is composed of an arbitrary number
of bytes that may not be an integer multiple of lanes, some
lanes may run out of data before others.
(Defined in 6.1.3 of mipi_DSI_specification_v.01-02-00)
However, for some DSI RX devices (for example, anx7625),
there is a limitation that packet number should be the same
on all DSI lanes. In other words, they need to end a HS at
the same time.
Because this limitation is for some specific DSI RX devices,
it is more reasonable to put the enable control in these
DSI RX drivers. If DSI TX driver knows the information,
they can adjust the setting for this situation.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-2-rex-bc.chen@mediatek.com
The datasheet lists the minimum Serial clock cycle (Write) as 66ns which is
15MHz. Mostly it can do much better than that and is in fact often run at
32MHz. With a clever driver that runs configuration commands at a low speed
and only the pixel data at the maximum speed the configuration can't be
messed up by transfer errors and the speed is only limited by the amount of
pixel glitches that one is able to tolerate.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124150757.17929-4-noralf@tronnes.org
The backlight property was lost during conversion to yaml in commit
abdd9e3705 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema").
Put it back.
Fixes: abdd9e3705 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema")
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124150757.17929-2-noralf@tronnes.org
Make sure we pull in the kernel-doc for this.
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220208151228.344997-1-matthew.auld@intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The komeda KMS driver will call drm_plane_create_color_properties() with
a default encoding and range values of BT601 and Limited Range,
respectively.
Since the initial value wasn't carried over in the state, the driver had
to set it again in komeda_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-20-maxime@cerno.tech
The komeda KMS driver will call drm_plane_create_zpos_property() with an
init value of the plane index.
Since the initial value wasn't carried over in the state, the driver had
to set it again in komeda_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-10-maxime@cerno.tech
komeda_plane_reset() does the state initialisation by copying a lot of
the code found in the __drm_atomic_helper_plane_reset(). Let's switch to
that helper and reduce the boilerplate.
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-2-maxime@cerno.tech
Fix the following coccicheck warning:
./drivers/gpu/drm/omapdrm/omap_overlay.c:89:22-25: ERROR: r_ovl is NULL
but dereferenced.
Here should be ovl->idx rather than r_ovl->idx.
Fixes: e02b5cc9e8 ("drm/omap: Add a 'right overlay' to plane state")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307095612.409090-1-wanjiabing@vivo.com
Set the error code to -ENOMEM if drm_random_order() fails.
Fixes: e6ff5ef811 ("drm/selftests: add drm buddy smoke testcase")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307125458.GA16710@kili
Since switch to simplefb/simpledrm VESA graphic mode selection with vga=
kernel parameter is no longer available with legacy BIOS.
The x86 realmode boot code enables the VESA graphic modes when option
FB_BOOT_VESA_SUPPORT is enabled.
This option is selected by vesafb but not simplefb/simpledrm.
To enable use of VESA modes with simplefb in legacy BIOS boot mode drop
dependency of BOOT_VESA_SUPPORT on FB, also drop the FB_ prefix. Select
the option from sysfb rather than the drivers that depend on it.
The BOOT_VESA_SUPPORT is not specific to framebuffer but rather to x86
platform, move it from fbdev to x86 Kconfig.
Fixes: e3263ab389 ("x86: provide platform-devices for boot-framebuffers")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/948c39940a4e99f5b43bdbcbe537faae71a43e1d.1645822213.git.msuchanek@suse.de
Hotplug events reported by bridge drivers over drm_bridge_hpd_notify()
get ignored unless somebody calls drm_bridge_hpd_enable(). When the
connector for the bridge is bridge_connector, such a call is done from
drm_bridge_connector_enable_hpd().
However drm_bridge_connector_enable_hpd() is never called on init paths,
documentation suggests that it is intended for suspend/resume paths.
In result, once encoders are switched to bridge_connector,
bridge-detected HPD stops working.
This patch adds a call to that API on init path.
This fixes HDMI HPD with rcar-du + adv7513 case when adv7513 reports HPD
events via interrupts.
Fixes: c24110a8fd ("drm: rcar-du: Use drm_bridge_connector_init() helper")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211225063151.2110878-1-nikita.yoush@cogentembedded.com
Fix following coccicheck warning:
drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c:316:11-12:
WARNING this kind of initialization is deprecated.
`void *map = map` has the same form of
uninitialized_var() macro. I remove the redundant assignement. It has
been tested with gcc (Debian 8.3.0-6) 8.3.0.
The patch which removed uninitialized_var() is:
https://lore.kernel.org/all/20121028102007.GA7547@gmail.com/
And there is very few "/* GCC */" comments in the Linux kernel code now.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228142352.18006-1-guozhengkui@vivo.com
Pointer mode is being assigned a value that is never read, it is
being re-assigned later with a new value. The initialization is
redundant and can be removed.
Cleans up clang scan build warning:
drivers/gpu/drm/solomon/ssd130x.c:582:27: warning: Value stored
to 'mode' during its initialization is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302175309.1098827-1-colin.i.king@gmail.com
Add a TODO item for optimizing blitting and format-conversion helpers
in DRM and fbdev. There's always demand for faster graphics output.
v4:
* fix typos (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-6-tzimmermann@suse.de
Improve the performance of cfb_imageblit() by manually unrolling
the inner blitting loop and moving some invariants out. The compiler
failed to do this automatically. This change keeps cfb_imageblit()
in sync with sys_imagebit().
A microbenchmark measures the average number of CPU cycles
for cfb_imageblit() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging).
cfb_imageblit(), new: 15724 cycles
cfb_imageblit(): old: 30566 cycles
In the optimized case, cfb_imageblit() is now ~2x faster than before.
v3:
* fix commit description (Pekka)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-5-tzimmermann@suse.de
Improve the performance of sys_imageblit() by manually unrolling
the inner blitting loop and moving some invariants out. The compiler
failed to do this automatically. The resulting binary code was even
slower than the cfb_imageblit() helper, which uses the same algorithm,
but operates on I/O memory.
A microbenchmark measures the average number of CPU cycles
for sys_imageblit() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging). The value
for CFB is given as a reference.
sys_imageblit(), new: 25934 cycles
sys_imageblit(), old: 35944 cycles
cfb_imageblit(): 30566 cycles
In the optimized case, sys_imageblit() is now ~30% faster than before
and ~20% faster than cfb_imageblit().
v2:
* move switch out of inner loop (Gerd)
* remove test for alignment of dst1 (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-3-tzimmermann@suse.de
Improve the performance of sys_fillrect() by using word-aligned
32/64-bit mov instructions. While the code tried to implement this,
the compiler failed to create fast instructions. The resulting
binary instructions were even slower than cfb_fillrect(), which
uses the same algorithm, but operates on I/O memory.
A microbenchmark measures the average number of CPU cycles
for sys_fillrect() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging). The value
for CFB is given as a reference.
sys_fillrect(), new: 26586 cycles
sys_fillrect(), old: 166603 cycles
cfb_fillrect(): 41012 cycles
In the optimized case, sys_fillrect() is now ~6x faster than before
and ~1.5x faster than the CFB implementation.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-2-tzimmermann@suse.de
For spdx
change tab to space delimiter
Use // for *.c
Replacements
commited to committed
regsiters to registers
initialze to initialize
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302124535.358060-1-trix@redhat.com
If the previous transfer didn't end with a command without DP_AUX_I2C_MOT,
the next read trasnfer will miss the first byte. But if the command in
previous transfer is requested with length 0, it's a no-op to anx7625
since it can't process this command. anx7625 requires the last command
to be read command with length > 0.
It's observed that if we clear the DP_AUX_I2C_MOT in read transfer, we
can still get correct data. Clear the read commands with DP_AUX_I2C_MOT
bit to fix this issue.
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217082224.1823916-1-hsinyi@chromium.org
Remove redundant error message (since now it is very similar to what
we do in drm_sched_init) and centralize all error handling in a
unique place, as we follow the same steps in any case of failure.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228181647.3794298-1-mwen@igalia.com
The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".
Switch to the new function and reduce boilerplate.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221074224.12920-1-jose.exposito89@gmail.com
The size of read_buf is READ_BUFFER_SIZE (200), so we can't access it
with read_buf + PAGE_SIZE (4096). Extend the READ_BUFFER_SIZE to 400 and
set the end position to read_buf + READ_BUFFER_SIZE.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228081421.1504213-1-hsinyi@chromium.org
Initialize bpc while creating panel_desc structure for RK101II01D-CT
Below warning is triggered since bpc is not being initialized
WARNING: CPU: 2 PID: 47 at drivers/gpu/drm/panel/panel-simple.c:614
panel_simple_probe+0x1b0/0x3c8
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210140300.11900-1-r-ravikumar@ti.com
Add MODULE_DEVICE_TABLE to the device tree table to create required
aliases needed for module to be loaded with device tree based platform.
Fixes: e19233955d ("drm/bridge: Add Cadence DSI driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921174059.17946-1-nm@ti.com
