In routine rtl92de_hw_init(), there are two places where a failure is
not handled correctly.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a number of loops to implement delays. These are replaced with
single calls to mdelay().
The need for a fix was noted by Andrew Morton <akpm@linux-foundation.org>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tests of a boolean against "true" are not needed as non-zero is sufficient..
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should be unnecessary if synchronize_irq is used.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare rtl8192de for the removal of irq_enaqbled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ERROR: "__bad_udelay" [drivers/net/wireless/rtlwifi/rtl8192de/rtl8192de.ko] undefined!
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch imports all shared header changes
from carl9170fw.git.
* update copyright boilerplate
* add some more strategic __aligned(4).
* WoWLAN
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the 'driver_initiated' function argument to
__cfg80211_stop_sched_scan() is not 0 then we'll return an
uninitialized 'err' from the function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on inputs from Johannes Berg <johannes@sipsolutions.net>
from http://article.gmane.org/gmane.linux.kernel.wireless.general/68193
and http://article.gmane.org/gmane.linux.kernel.wireless.general/71702
In xmit path, devices that do full hardware crypto (including
MMIC and ICV) need no tailroom. For such devices, tailroom
reservation can be skipped if all the keys are programmed into
the hardware (i.e software crypto is not used for any of the
keys) and none of the keys wants software to generate Michael
MIC and IV.
v2: Added check for IV along with MMIC.
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Tested-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Cc: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
v3: Fixing races to avoid WARNING: at net/mac80211/wpa.c:397
ccmp_encrypt_skb+0xc4/0x1f0
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
v4: Added links with message ID
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions allocate all the Tx context. Only the simple tx_init is exported as API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The transport layer ness to release all rx ressources. This function is an API for it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The transport layer is responsible for all the queues, DMA rings etc...
This is the beginning of the separation of all the code that is tighly
related to HW design to the aforementioned transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Add the parameter to disable stuck queue watchdog timer, different platforms
might have different timing. Provide the option to disable the timer to prevent
un-necessary firmware reload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
To make sure not having issues when adding new testmode commands or attributes
in the future, re-define the enum. no functional changes
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Emmanuel noticed that there's no explicit checking
that prevents the driver from attempting to issue
multiple synchronous commands at the same time and
wrote a patch to check. However, his patch warns
only if a collision actually happened, an unlikely
thing since the driver mutex should be held for
synchronous command submissions.
So instead of checking that a collision happened
add a check that the mutex is held which ensures
that collisions can't happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
"i" should be an int here because we are trying to use it to count
to 10000. The original code looks like it could hang in a forever
loop.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After adding rtl8192de to linux-next, making the rtlwifi drivers be built-in
results in the following warnings:
LD drivers/net/wireless/rtlwifi/built-in.o
drivers/net/wireless/rtlwifi/rtl8192de/built-in.o: In function `rtl92ce_sw_led_on':
(.text+0x11fb6): multiple definition of `rtl92ce_sw_led_on'
drivers/net/wireless/rtlwifi/rtl8192ce/built-in.o:(.text+0xa326): first defined here
drivers/net/wireless/rtlwifi/rtl8192de/built-in.o:(.bss+0x0): multiple definition of `dm_digtable'
drivers/net/wireless/rtlwifi/rtl8192c/built-in.o:(.bss+0x0): first defined here
ld: Warning: size of symbol `dm_digtable' changed from 40 in drivers/net/wireless/rtlwifi/rtl8192c/built-in.o to 48 in drivers/net/wireless/rtlwifi/rtl8192de/built-in.o
drivers/net/wireless/rtlwifi/rtl8192de/built-in.o: In function `rtl92ce_sw_led_off':
(.text+0x11cfe): multiple definition of `rtl92ce_sw_led_off'
drivers/net/wireless/rtlwifi/rtl8192ce/built-in.o:(.text+0xa06e): first defined here
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes additional steps are performed while initializing 2059 radio.
We did not find the condition yet, so make it always true for now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They were written from observing MMIO writes to registers 0x72 0x74 and
0x73 right after phy_write(0x017e) <- 0x3830 which finishes chennel
switching. RegExps were used to translate writes to arrays.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a station, use the information given in the mac80211
populated ieee80211_sta structure to determine if it supports WME.
Provide this information to the FW.
This patch depends on "mac80211: propagate information about
STA WME support down".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a memeber to the ieee80211_sta structure to indicate whether the STA
supports WME.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use PCI_VENDOR_ID_* from pci_ids.h instead of creating #define locally.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Also, remove unnecessary and unused #defines for PCI.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tables were taken from observing writes in MMIO dumps.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Starring at MMIO dumps around PHY channel switching has led to finding
serie of 3 similar ops this patch implements.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After calibrating radio you can find few PHY writes in MMIO dumps:
phy_read(0x0009) -> 0x0000
phy_write(0x01ce) <- 0x03dd
phy_write(0x01cf) <- 0x03d9
phy_write(0x01d0) <- 0x03d5
phy_write(0x01d1) <- 0x0424
phy_write(0x01d2) <- 0x0429
phy_write(0x01d3) <- 0x042d
By comparing to N-PHY code we found out that they are PHY tables for
channel switching plus band info read at the beginning.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are big arrays uploaded to the hardware on init, calibration, etc.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlagn: map command buffers BIDI" uses the DMA_* enumerations for DMA
directions, even though the pci_* DMA API is still in use. That patch
was undoubtedly developed on top of "iwlagn: don't use the PCI wrappers
for DMA operation", which is due in the next release.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the tx_frames_pending() driver callback to determine if Tx frames are
pending for its internal queues. If so postpone the dynamic PS timeout
to avoid interrupting Tx traffic.
The commit e8306f9894 enabled this
behavior for drivers with IEEE80211_HW_PS_NULLFUNC_STACK. We enable this
for all drivers supporting dynamic PS.
This patch helps improve performance in noisy environments.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit ff938e43d3 (net: use pci_dev->revision,
again) already converted this driver to using the 'revision' field of 'struct
pci_dev' but commit 084dd79172 (iwlagn: move PCI
related operations from probe and remove to PCI layer) has again added the code
to read the PCI revision ID register...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prior to a5ffddb70c "mwifiex: remove casts of void pointers" the
code assumed that the data_buf parameter could be a NULL pointer.
The patch preserved some NULL checks but not consistently, so there
was a potential for NULL dereferences and it changed the behavior.
This patch restores the original behavior.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The received tx status of aggregated frame without BlockAck may
cause deaf state in AR5416 cards. So the driver does a reset to
recover. When this happens, we release the pcu_lock before doing
a reset as ath_rest acquires pcu_lock. This is ugly and also not
atomic. Fixing this addresses the TX DMA failure also.
ath_tx_complete_aggr can be called from different paths which
takes different variants of spin_lock. This patch also addresses
the following warning.
WARNING: at kernel/timer.c:1011 del_timer_sync+0x4e/0x50()
Call Trace:
<IRQ> [<ffffffff8104be3a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104be85>] warn_slowpath_null+0x15/0x20
[<ffffffff8105915e>] del_timer_sync+0x4e/0x50
[<ffffffffa03726be>] ath_reset+0x3e/0x210 [ath9k]
[<ffffffff8135cdaf>] ? _raw_spin_unlock_bh+0x1f/0x30
[<ffffffffa037760a>] ath_tx_complete_aggr.isra.26+0x54a/0xa40 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
