This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN. The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check to make certain mac_table was actually allocated and is not
NULL. If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
Test script:
ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_intr and ixgbe/ixgbevf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit dfaf891dd3 ("ixgbe: Refactor the RSS configuration code")
introduced a few kernel-doc errors:
1) The function name is missing;
2) The format is wrong;
3) The short description is redundant.
Fix all the above for the correct execution of the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete a redundant include of net/vxlan.h.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the new netdev op to trust VF in ixgbe.
The administrator can turn on and off VF trusted by ip command which
supports trust message.
# ip link set dev eth0 vf 1 trust on
or
# ip link set dev eth0 vf 1 trust off
Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch disables LRO by default in favor of GRO.
LRO is incompatible with forwarding and is disabled when forwarding
is turned on which makes the default offloads of the driver
inconsistent. LRO can still be enabled via ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that flow control packets initiated by the VF are
dropped and reported as spoofed.
Flow control packets can be used to limit the throughput or as DOS
attack when generated from a VF. Flow control is not supported per VF
hence any pause frames generated from a VF are considered malicious.
Also cleaned up indentation and some redundant comments.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the addition of X550em_x SFP+ support, the driver is now
functionally equivalent to what will be the 4.2.1 driver when
released, so change the version to match.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal interrupt (IXGBE_EIMS_TS) is not an SDP, so it
doesn't need to be enabled in ixgbe_setup_gpie(). In fact the
value is simply not for the GPIE register at all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.
Thanks to Alex Duyck for this fix.
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device ID for X550EM device with SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the SFP insertion interrupt on X550EM devices with
SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is part of the future enablement of X550 SFP+ support. This
HW uses different SDP so the interrupts need to be set up accordingly.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
After:
212992 65507 60.00 1100413 0 9611.2 10.73 0.549
212992 60.00 974132 8508.3 11.69 0.598
Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways. If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs. The occurs regardless of
whether the VF count was later modified through sysfs. If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe. If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.
>From the comment, commit da36b64736 ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.
This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device. Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: Tal Abudi <talabudi@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: Tom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use kzalloc rather than kcalloc(1..
The semantic patch that makes this change is as follows:
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS could be leveraged by taking account L4 src/dst ports
as ingredients, thus ingress skb Rx hash type should honor
such the real configuration.
Signed-off-by: Fan Du <fan.du@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for another 10baseT X550 device.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
We do this by updating the ixgbe_is_sfp to be aware of the
new X550 devices. This also includes a modified check generating
the EICR mask to be more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for receiving interrupts from a external copper
PHY for the X550 part. This includes enabling, detection as well as
re-enablement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The over heat message is displayed for multiple reasons but the text is
cut-n-pasted for each of these cases. This patch pulls the text from the
same location. I noticed this as I am about to add another case.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This new method will control the PHY power state. You pass in the
state you wish to change to (ether on or off). For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom. This patch enables
these devices this support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values. These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because error codes are negative, it only makes sense to
consistently use signed types when handling them. Also remove
some explicit comparisons with 0 on these variables.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the new netdev op to allow user to enable/disable the ability
of a specific VF to query its RSS Indirection Table and an RSS Hash Key.
This patch limits the new feature support to 82599 and x540 devices only.
Support for other devices will be added later.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added get_rxfh_indir_size, get_rxfh_key_size and get_rxfh ethtool_ops
callbacks implementations.
This enables the ethtool's "-x" and "--show-rxfh[-indir]" options.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a preparation for enablement of ethtool RSS indirection
table and hash key querying. We don't want to read registers every time
the RSS info is queried. Therefore we will store its current content in the
arrays in the adapter struct and will read it from there (instead of from
registers) when requested.
Will change the code that writes the indirection table and hash key into
the HW registers to take its content from these arrays. This will also
simplify the indirection table updating ethtool callback implementation
in the future.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver hasn't used call_rcu to free the rings for some time now.
Since that is the case the call to rcu_barrier can be dropped since calls
to kfree_rcu don't require it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the HW_VLAN_CTAG_FILTER bit is not falsely
advertised as being a feature that can be toggled on ixgbe parts. The
driver was setting the bit in features and letting it be inherited by
hw_features, however the driver was actually ignoring the value of the bit
and just assuming it was always set. As a result VLAN filtering was always
enabled which is a requirement for SR-IOV, VMDq, DCB, FCoE, and possibly
other features within the adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will enable X550 Source Address Prunning for VEPA
bridge mode. This requires that we also have replication enabled
as well, while in this mode.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch gathers together all the logic needed to configure bridge
modes. Currently that it is rather simple but this is really laying
the ground work for future X550 feature enhancement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently storing our BRIDGE_MODE as a bit in our adapter flags.
This patch will store the actual mode instead which minimizes obfuscation
and makes following patches for X550 simpler.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some dead code from the cleanup path for ixgbe.
Setting and clearing the flag doesn't do anything since all we are
doing is setting the flag, scheduling NAPI, clearing the flag and
then letting netpoll do the polling cleanup. As such it doesn't
make much sense to have it there.
This patch also removes one minor white-space error.
CC: <kernel-team@fb.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the X550 mac type we have to do additional steps around
enabling/disabling Rx. This patch will add a layer of indirection
around these support functions to enable this.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that dma_rmb is used when reading the Rx
descriptor. The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.
In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit. This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.
There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has logic to free up used data in case any of the checks in
ixgbe_probe() fail, however there is a similar set of cleanups that can
occur on driver unload in ixgbe_remove() which can cause the rmmod command
to crash.
This patch aims to fix the logic by moving pci_set_drvdata() after all error
checks and then adds a check in ixgbe_remove() to skip it altogether if
adapter comes up empty.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now support X550 mac's bump the version number to reflect this.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the function pointer structure to include the new
X550 class MAC types. This creates a new file ixgbe_x550.c that contains
all of the new methods. Because of similarities to the X540 part in
some cases we just use it's methods where they can be used without any
modification. These exported functions are now defined in the new
ixgbe_x540.h file.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new X550 family of MAC's will have a larger RSS hash (16 -> 64).
It will also support individual VF to have their own independent RSS
hash key. This patch will enable this functionality
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accessing the CIAA/D register can block access to the PCI config space.
This patch removes the read/write operations to the CIAA/D registers
and makes use of standard kernel functions for accessing the PCI config
space.
In addition it moves ixgbevf_check_for_bad_vf() into the watchdog subtask
which reduces the frequency of the checks.
CC: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to look up the MAC address in Open Firmware on systems that
support it. On SPARC resort to using the IDPROM if no OF address is
found.
Signed-off-by: Martin K Petersen <martin.petersen@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the tail writes for the ixgbe descriptor queues. The
current implementation had me confused as I wasn't sure if it was still
making use of the surprise remove logic or not.
It also adds the mmiowb which is needed on ia64, mips, and a couple other
architectures in order to synchronize the MMIO writes with the Tx queue
_xmit_lock spinlock.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To allow brport device to return current brport flags set on port. Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink() is currently only called on the slave if
IFLA_AF_SPEC is set but this is a very fragile assumption and may
change in the future.
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: a77dcb8c8 ("be2net: set and query VEB/VEPA mode of the PF interface")
Fixes: 815cccbf1 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on a different issue, I noticed an annoying use
after free bug on my machine when unloading the ixgbe driver:
[ 8642.318797] ixgbe 0000:02:00.1: removed PHC on p2p2
[ 8642.742716] ixgbe 0000:02:00.1: complete
[ 8642.743784] BUG: unable to handle kernel paging request at ffff8807d3740a90
[ 8642.744828] IP: [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[ 8642.745886] PGD 20c6067 PUD 81c1f6067 PMD 81c15a067 PTE 80000007d3740060
[ 8642.746956] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[ 8642.748039] Modules linked in: [...]
[ 8642.752929] CPU: 1 PID: 1225 Comm: rmmod Not tainted 3.18.0-rc2+ #49
[ 8642.754203] Hardware name: Supermicro X10SLM-F/X10SLM-F, BIOS 1.1b 11/01/2013
[ 8642.755505] task: ffff8807e34d3fe0 ti: ffff8807b7204000 task.ti: ffff8807b7204000
[ 8642.756831] RIP: 0010:[<ffffffffa01c77dc>] [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[...]
[ 8642.774335] Stack:
[ 8642.775805] ffff8807ee824098 ffff8807ee824098 ffffffffa01f3000 ffff8807ee824000
[ 8642.777326] ffff8807b7207e18 ffffffff8137720f ffff8807ee824098 ffff8807ee824098
[ 8642.778848] ffffffffa01f3068 ffff8807ee8240f8 ffff8807b7207e38 ffffffff8144180f
[ 8642.780365] Call Trace:
[ 8642.781869] [<ffffffff8137720f>] pci_device_remove+0x3f/0xc0
[ 8642.783395] [<ffffffff8144180f>] __device_release_driver+0x7f/0xf0
[ 8642.784876] [<ffffffff814421f8>] driver_detach+0xb8/0xc0
[ 8642.786352] [<ffffffff814414a9>] bus_remove_driver+0x59/0xe0
[ 8642.787783] [<ffffffff814429d0>] driver_unregister+0x30/0x70
[ 8642.789202] [<ffffffff81375c65>] pci_unregister_driver+0x25/0xa0
[ 8642.790657] [<ffffffffa01eb38e>] ixgbe_exit_module+0x1c/0xc8e [ixgbe]
[ 8642.792064] [<ffffffff810f93a2>] SyS_delete_module+0x132/0x1c0
[ 8642.793450] [<ffffffff81012c61>] ? do_notify_resume+0x61/0xa0
[ 8642.794837] [<ffffffff816d2029>] system_call_fastpath+0x12/0x17
The issue is that test_and_set_bit() done on adapter->state is being
performed *after* the netdevice has been freed via free_netdev().
When netdev is being allocated on initialization time, it allocates
a private area, here struct ixgbe_adapter, that resides after the
net_device structure. In ixgbe_probe(), the device init routine,
we set up the adapter after alloc_etherdev_mq() on the private area
and add a reference for the pci_dev as well via pci_set_drvdata().
Both in the error path of ixgbe_probe(), but also on module unload
when ixgbe_remove() is being called, commit 41c62843eb ("ixgbe:
Fix rcu warnings induced by LER") accesses adapter after free_netdev().
The patch stores the result in a bool and thus fixes above oops on my
side.
Fixes: 41c62843eb ("ixgbe: Fix rcu warnings induced by LER")
Cc: stable <stable@vger.kernel.org>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IXGBE adapter seems to require that VLAN filtering be enabled if
VMDQ or SRIOV are enabled. When those functions are disabled,
VLAN filtering may be disabled in promiscuous mode.
Prior to commit a9b8943ee1 ("ixgbe: remove vlan_filter_disable
and enable functions")
The logic was correct. However, after the commit the logic
got reversed and VLAN filtered in now turned on when VMDQ/SRIOV
is disabled.
This patch changes the condition to enable hw vlan filtered
when VMDQ or SRIOV is enabled.
Fixes: a9b8943ee1 ("ixgbe: remove vlan_filter_disable and enable functions")
Cc: stable <stable@vger.kernel.org>
CC: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel drivers were pretty much just using the plain vanilla GFP flags
in their calls to __skb_alloc_page so this change makes it so that they use
dev_alloc_page which just uses GFP_ATOMIC for the gfp_flags value.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split off the setting of the RSS key into its own function. This
will help when we add support for X550 which can have different
RSS keys per pool.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will add in the new MAC defines and fit it into the switch
cases throughout the driver. New functionality and enablement support will
be added in following patches.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the logic behind dynamically setting TXDCTL.WTHRESH
depending on interrupt throttle rate (ITR) setting regardless of BQL.
Previously TXDCTL.WTHRESH was dynamically being set only with BQL being
enabled, but we have to set it regardless of BQL when ITR is low to avoid
Tx stalls/hangs.
CC: John Greene <jogreene@redhat.com>
Reported by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the normal packet completion path to dev_consume_skb_any() so
packet drop profiling via dropwatch or perf top -G -e skb_kfree_skb
is not cluttered with false hits.
Compile tested only. There is a dev_kfree_skb_any() in the routine
ixgbe_ptp_tx_hwtstamp() in ixgbe_ptp.c that looks like a conversion
candidate but I wasn't familiar enough with the code to pull the
trigger.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a hardware Tx timestamp is requested, an uninitialized
workqueue entry may be scheduled, especially on an 82598 adapter.
Add a check for a PTP clock to avoid that. Also only apply the
unlikely to the first term of the conditional. That will make the
rest of the checks be in the cold path.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because bd_number is not useful anymore, so remove it from adapter struct, or
if keep it, we have to fix the boards driven counter bug in ixgbe_remove() and
ixgbe_probe() only for trivial debug purpose -- other output is enough.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq.
The reason for removing this is to avoid the extra latency introduced by the
MMIO write. This can amount to somewhere around an extra 100ns of latency and
one extra message worth of PCIe bus overhead.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves warnings produced by ixgbe in W=2 kernel
builds. There are missing-field-initializers warnings and shadow
warnings. None of these point to any deeper problem, so just
resolve them so any new warnings get analyzed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbe to drop the ixgbe_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.
This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases. The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When xmit_more mode is being used and the ring is about to
become full or the stack has stopped the ring, enforce a tail
pointer write to the hw. Otherwise, we could risk a TX hang.
Code suggested by Alexander Duyck.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the deferred tail pointer flush API for the ixgbe
driver. Similar version also proposed longer time ago by Alexander Duyck.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the display of the minimum link qualification check
if we might be in a virtual machine. This check is incorrect and
misleading in this case, since we actually don't really know what the
available bandwidth is. To do so, we simply check whether each function
on the bus matches our device id. If it doesn't the most likely scenario
is that we're directly assigned to a virtual machine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug in the misuse of the list_for_each macro to loop over every
entry in the bus_list. Instead of attempting to loop over the list from
a random entry point, go up to the bus and use the real list_head entry
point. This prevents the possible read or write of unallocated or
incorrectly addressed memory.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change some uses of strncpy to use the more appropriate strlcpy
when clearing is not needed to prevent information leakage. Also
change some length arguments to use the preferred sizeof form.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_probe, the code at label err_dma can dereference adapter
when it has a NULL value. The check is there to avoid disabling a
disabled device. When adapter is NULL, treat it as if the device
is enabled, because it is enabled in that case.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
In cases where the driver is loaded while there are no SFP+ modules in
the cage the interface was not being detected as SFP capable. To account
for this the driver called identify_sfp in ixgbe_get_settings to make
sure the data is correct. However when there is no SFP+ module in the cage
the driver waits for the I2C reads to time out which can take more than a
second and will cause issues with tools (like net-snmp) that may poll
for that information.
This patch resolves the issue by identifying interfaces with no PHY
type set as SFP capable which allows the driver to detect the SFP module
when the interface is brought up. As result of this we can also remove the
identify_sfp call from ixgbe_get_settings.
v2: remove the 82599 specific check since we have 82598 devices that are SFP
capable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resume path calls .open but suspend path cannot call .stop because
fdirs should not be freed and control over hardware should not be
released until WoL is configured. To avoid having to duplicate all
changes made in .stop on suspend path split out part of .stop that
is relevant during suspend and call it from .stop and during suspend.
This fix also ensures that ixgbe_ptp_suspend is called during the
suspend path, and helps avoid similar errors. We can't call
ixgbe_ptp_stop, since it will free the PTP clock device, which we
shouldn't be doing during a suspend path.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was calling setup_link to make sure that fiber interfaces with MNG FW
enabled will get link on probe because the laser was most likely turned off.
This prevented non-fiber devices with MNG FW from linking at 100Mbps.
This patch adds a check to only call setup_link for fiber devices.
Reported-and-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, igbvf, ixgbe, i40e and i40evf.
Jacob provides eight patches to cleanup the ixgbe driver to resolve various
checkpatch.pl warnings/errors as well as minor coding style issues.
Stephen Hemminger and I provide simple cleanups of void functions which
had useless return statements at the end of the function which are not
needed.
v2: Dropped Emil's patch "ixgbe: fix the detection of SFP+ capable interfaces"
while I wait for his updated patch to be validated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The contents of this patch were originally generated by
"scripts/checkpatch.pl --fix-inplace --types CODE_INDENT,LEADING_SPACE
drivers/net/ethernet/ixgbe/*.[ch]", and then hand verified for
consistency.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mac_table API based on work done for igb, which includes functions
to add and delete mac filters. This simplifies code for various entities
that use MAC filters such as VMDQ, SR-IOV, MACVLAN, and such.
Reported-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In line with changes done by Alex Duyck regarding unicast filters, we
now only set multicast filters when the interface is not in promiscuous
mode for multicast packets. This also has an impact on the RAR usage
such that SR-IOV has some RARs reserved for its own usage.
Reported-by: Alex Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously these functions handled stripping setup as well, but this has
already been removed from these functions. Rather than encapsulating
this into a function, we can just do the work directly in set_rx_mode.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register reads are slow, so don't inline them.
Size before:
text data bss dec hex filename
226337 8280 552 235169 396a1 ixgbe.ko
Size after:
text data bss dec hex filename
194578 8280 552 203410 31a92 ixgbe.ko
for about a 14% reduction in text size.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since fc.high_water is an array, we should treat low_water as an array
also. This allows the algorithm to output different values for different
TCs, and then we can distinguish between them. In addition, this patch
changes one path that didn't honor the return value from ixgbe_setup_fc.
Reported-by: Aaron Salter <aaron.k.salter@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Time stamping resources are per-interface so there is no need
to keep separate last_rx_timestamp for each Rx ring, move
last_rx_timestamp to the adapter structure.
With last_rx_timestamp inside adapter, ixgbe_ptp_rx_hwtstamp()
inline function is reduced to a single if statement so it is
no longer necessary. If statement is placed directly in
ixgbe_process_skb_fields() fixing likely/unlikely marking.
Checks for q_vector or adapter to be NULL are superfluous.
Comment about taking I/O hit is a leftover from previous design.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There needs to be an indication when the service task has been
initialized. This is because register access prior to that time
can detect a removal and attempt to schedule the service task.
Adding the __IXGBE_SERVICE_INITED bit allows this to be checked
and if not set prevent the service task scheduling. By checking
for a removal right after initialization, the probe can be failed
at that point without getting the service task involved.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve some rcu warnings produced when LER actions take place.
This appears to be due to not holding the rtnl lock when calling
ixgbe_down, so hold the lock. Also avoid disabling the device
when it is already disabled. This check is necessary because the
callback can be called more than once in some cases.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.
In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We use to cache whether the MNG FW was enabled, how since this isn't
static we really need to verify with each check. This patch makes that
change.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inline with the current use for ixgbe_read_pci_cfg_word, create a
similar function for writing PCI config, which checks whether the
adapter has been removed first, if Live Error Recovery has been enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the contact information on the ixgbe driver files so
that every file includes the Linux NICS address, as it is still used,
but only a few of the files mentioned it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the new SIOCGHWTSTAMP ioctl, which enables a
process to determine the current timestamp configuration. In order to
implement this, store a copy of the timestamp configuration. In
addition, we can remove the 'int cmd' parameter as the new set_ts_config
function doesn't use it. I also fixed a typo in the function
description.
-v2
* Only save the settings after validating them
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration space reads should also be checked for removal. So
add some checks related to config space accesses.
v2:
* Fixed indent
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hw_addr needs to be restored in the pcie recovery path or
else the device will be perpetually removed. Also restore the
value in the resume path.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add WoL support for port 0 of a new 82599-based device.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when we noticed a HW ECC error we would request the use reload
the driver to force a reset of the part. This was done due to the mistaken
believe that a normal reset would not be sufficient. Well it turns out it
would be so now we just schedule a reset upon seeing the ECC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version number to better match functionality provided with out
of tree driver of the same version.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 43dc4e01 Limit number of reported VFs to device
specific value It doesn't work and always returns -EBUSY because VFs are
already enabled.
ixgbe_enable_sriov()
pci_enable_sriov()
sriov_enable()
{
... ..
iov->ctrl |= PCI_SRIOV_CTRL_VFE | PCI_SRIOV_CTRL_MSE;
pci_cfg_access_lock(dev);
... ...
}
pci_sriov_set_totalvfs()
{
... ...
if (dev->sriov->ctrl & PCI_SRIOV_CTRL_VFE)
return -EBUSY;
...
}
So should set driver_max_VFs with pci_sriov_set_totalvfs() before
enable VFs with ixgbe_enable_sriov().
V2: revised for net-next tree.
Signed-off-by: Ethan Zhao <ethan.kernel@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because ixgbe driver limit the max number of VF
functions could be enabled to 63, so define one macro IXGBE_MAX_VFS_DRV_LIMIT
and cleanup the const 63 in code.
v3: revised for net-next tree.
Signed-off-by: Ethan Zhao <ethan.kernel@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_service_task() is calling ixgbe_reinit_locked() without
the rtnl_lock being held. This is because it is being called
from a worker thread and not a rtnl netlink or dcbnl path.
Add rtnl_{un}lock() semantics. I found this during code review.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional checks are needed for a detected removal not to cause
problems. Some involve simply avoiding a lot of stuff that can't
do anything good, and also cases where the phony return value can
cause problems. In addition, down the adapter when the removal is
sensed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check all register reads for adapter removal by checking the status
register after any register read that returns 0xFFFFFFFF. Since the
status register will never return 0xFFFFFFFF unless the adapter is
removed, such a value from a status register read confirms the
removal.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel coding standard prefers static inline functions instead
of macros, so use them for register accessors. This is to prepare
for adding LER, Live Error Recovery, checks to those accessors.
Temporarily provide macros for calling the new static inline
accessors until all references are changed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBE_DOWN. This did not work before
introduction of the __IXGBE_REMOVING bit, because of overloading
of __IXGBE_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBE_DOWN bit.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bit, __IXGBE_REMOVING, to indicate that the module is being
removed. The __IXGBE_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBE_DOWN
and __IXGBE_REMOVE. Notably, setting either bit will prevent service
task execution.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_L2FW_DOFFLOAD allows upper layer net devices such
as macvlan to use queues in the hardware to directly submit and
receive skbs.
This creates a subtle change in the datapath though. One change
being the skb may no longer use the root devices qdisc.
Because users may not expect this we can't enable the feature
by default unless the hardware can offload all the software
functionality above it. So for now disable it by default and
let users opt in.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When compiling with -Wstrict-prototypes gcc catches a static
I missed.
./ixgbe_main.c:4254: warning: no previous prototype for 'ixgbe_fwd_ring_down'
Reported-by: Phillip Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
The max_vfs parameter has a limit of 63 and silently fails (adding 0 vfs) when
it is out of range. This patch adds a warning so that the user knows something
went wrong. Also, this patch moves the warning in ixgbe_enable_sriov() to where
max_vfs is checked, so that even an out of range value will show the deprecated
warning. Previously, an out of range parameter didn't even warn the user to use
the new sysfs interface instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of stations in use is kept in the num_rx_pools counter
in the ixgbe_adapter structure. This is in turn used by the queue
allocation scheme to determine how many queues are needed to support
the number of pools in use with the current feature set.
This works as long as the pools are added and destroyed in order
because (num_rx_pools * queues_per_pool) is equal to the last
queue in use by a pool. But as soon as you delete a pool out of
order this is no longer the case. So the above multiplication
allocates to few queues and a pool may reference a ring that has
not been allocated/initialized.
To resolve use the bit mask of in use pools to determine the final
pool being used and allocate enough queues so that we don't
inadvertently remove its queues.
# ip link add link eth2 \
numtxqueues 4 numrxqueues 4 txqueuelen 50 type macvlan
# ip link set dev macvlan0 up
# ip link add link eth2 \
numtxqueues 4 numrxqueues 4 txqueuelen 50 type macvlan
# ip link set dev macvlan1 up
# for i in {0..100}; do
ip link set dev macvlan0 down; ip link set dev macvlan0 up;
done;
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the recent support for layer 2 hardware acceleration, I added a
few references to real_num_rx_queues and num_rx_queues which are
only available with CONFIG_RPS.
The fix is first to remove unnecessary references to num_rx_queues.
Because the hardware offload case is limited to cases where RX queues
and TX queues are equal we only need a single check. Then wrap the
single case in an ifdef.
The patch that introduce this is here,
commit a6cc0cfa72
Author: John Fastabend <john.r.fastabend@intel.com>
Date: Wed Nov 6 09:54:46 2013 -0800
net: Add layer 2 hardware acceleration operations for macvlan devices
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that l2 acceleration ops are in place from the prior patch,
enable ixgbe to take advantage of these operations. Allow it to
allocate queues for a macvlan so that when we transmit a frame,
we can do the switching in hardware inside the ixgbe card, rather
than in software.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch resolves an issue where the MTA table can be cleared when the
interface is reset while in promisc mode. As result IPv6 traffic between
VFs will be interrupted.
This patch makes the update of the MTA table unconditional to avoid the
inconsistent clearing on reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the unnecessary display of PCIe bandwidth twice. Since the
ixgbe_check_minimum_link does a better job, and ensures accurate detection on
even complex chains, this older check is no longer necessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the ixgbe_check_minimum_link function to correctly show that
there is some minor loss of encoding, even though we don't calculate it in the
max GT/s equation. It is small enough to not bother, but is better to report it
than not.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_napi_disable_all calls napi_disable on each queue, however the busy
polling code introduced a local_bh_disable()d context around the napi_disable.
The original author did not realize that napi_disable might sleep, which would
cause a sleep while atomic BUG. In addition, on a single processor system, the
ixgbe_qv_lock_napi loop shouldn't have to mdelay. This patch adds an
ixgbe_qv_disable along with a new IXGBE_QV_STATE_DISABLED bit, which it uses to
indicate to the poll and napi routines that the q_vector has been disabled. Now
the ixgbe_napi_disable_all function will wait until all pending work has been
finished and prevent any future work from being started.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: Alexander Duyck <alexander.duyck@intel.com>
Cc: Hyong-Youb Kim <hykim@myri.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
use pcie_capability_read_word() to simplify code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function previously had the same check as used by the
ixgbe_pcie_from_parent. As the hardcode is due to the device having an internal
switch, this function should simply use the call from ixgbe_pcie_from_parent.
This reduces code complexity and makes it less likely a developer will forget
to update the list in the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames the LL_EXTENDED_STATS and some of the functions required to
implement busy polling in the ixgbe driver, in order to remove the marketing
"low latency" blurb which hides what the code actually does.
This furthers work which was requested by Linus Torvalds when the initial busy
poll code was included in the kernel. The code in the ixgbe driver itself was
never properly renamed to reflect the change to busy polling as the title.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
pci_using_dac = 0;
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
QSFP+ modules do not support auto negotiation and should advertise only
one speed at a time.
This patch adds logic in ethtool to allow setting and reporting the
advertised speed at either 1Gbps or 10Gbps, but not both. Also limits
the speed set in ixgbe_sfp_link_config_subtask() to highest supported.
Previously the link was set to whatever the supported speeds were.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the configure_rx path in order to properly disable RSC
hardware logic when the user disables it. Previously we only disabled RSC in the
queue settings, but this does not fully disable hardware RSC logic which can
lead to some unexpected performance issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that QSFP+ modules use the SFP+ code path for
setting up link.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some minor log messages cleanup, changing the level one message is logged,
adding a bit of detail to another and put all the text on one line.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue with the 82599 adapter where it can potentially keep
link lights up when the adapter has gone down. The patch adds a function which
ensures link is disabled, and calls this function when the adapter transitions
to a down state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a x520 based quad-port (4x10Gbps) NIC with a single QSFP+
connector. Changes were required to our identify functions due to
different eeprom address which is also included here.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a lockdep issue created due to ixgbe_ptp_stop always running
cancel_work_sync even if the work item had not been created properly with
INIT_WORK. This is caused because ixgbe_ptp_stop did not check to actually
ensure PTP was running first. The new implementation introduces a state in the
&adapter->state field which is used to indicate that PTP is running. (This
replaces the IXGBE_FLAG2_PTP_ENABLED field). This state will use the atomic
set_bit, test_bit, and test_and_clear_bit functions. ixgbe_ptp_stop will check
to ensure that PTP was enabled, (and if not, it will not attempt to do any
cleanup work from ixgbe_ptp_init). This resolves the lockdep annotation warning
found by Stephen Hemminger
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch uses the new pcie_get_minimum_link function to perform a check to
ensure that the adapter is hooked into a slot which is capable of providing the
necessary bandwidth. This check supersedes the original method which only
checked the current pci device. The new method is capable of determining the
minimum speed and link of an entire PCI chain.
-v2-
* update the error message to include encoding loss
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes several issues with the previous implementation of the
SFF data dump of SFP+ modules:
- removed the __IXGBE_READ_I2C flag - I2C access locking is handled in the
HW specific routines
- fixed the read loop to read data from ee->offset to ee->len
- the reads fail if __IXGBE_IN_SFP_INIT is set in the process - this is
needed because on some HW I2C operations can take long time and disrupt
the SFP and link detection process
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the version number to better match with a similar version of the
out of tree driver.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally ixgbe_device_supports_autoneg_fc() was only expected to
be called by copper devices. This would lead to false information
to be displayed via ethtool.
v2: changed ixgbe_device_supports_autoneg_fc() to a bool function,
it returns bool. Based on feedback from David Miller
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using the new bridge FDB interface to allow SR-IOV virtual function
network devices to communicate with SW bridged network devices the
physical function is placed into promiscuous mode and hardware VLAN
filtering is disabled. This defeats the ability to use VLAN tagging
to isolate user networks. When the device is in promiscuous mode and
VT mode simultaneously ensure that VLAN hardware filtering remains
enabled.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename ndo_ll_poll to ndo_busy_poll.
Rename sk_mark_ll to sk_mark_napi_id.
Rename skb_mark_ll to skb_mark_napi_id.
Correct all useres of these functions.
Update comments and defines in include/net/busy_poll.h
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional statistics to the ixgbe driver for ndo_ll_poll
Defined under LL_EXTENDED_STATS
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ixgbe driver code implementing ndo_ll_poll.
Adds ndo_ll_poll method and locking between it and the napi poll.
When receiving a packet we use skb_mark_ll to record the napi it came from.
Add each napi to the napi_hash right after netif_napi_add().
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the ixgbe_msix_other was writing the full 32bits of the set
interrupts, instead of only the ones which the ixgbe_msix_other is
handling. This resulted in a loss of performance when the X540's PPS feature is
enabled due to sometimes clearing queue interrupts which resulted in the driver
not getting the interrupt for cleaning the q_vector rings often enough. The fix
is to simply mask the lower 16bits off so that this handler does not write them
in the EICR, which causes them to remain high and be properly handled by the
clean_rings interrupt routine as normal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a define and WOL support for a new subdevice ID.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable wol_supported really is just checking whether it is enabled, rather
than whether it is supported. If it is enabled it will be supported, but this
does not necessarily hold true the other way around. This patch renames the
variable to avoid confusion.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the new OCP x520 adapter. This support
includes WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Protect the code by bailing out of ixgbe_update_itr() when this occurs.
The next call to ixgbe_update_itr will continue to dynamically update ITR.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
