The current probe function calls v4l2_ctrl_handler_setup() before
initializing the format info. This triggers call paths such as:
imx274_probe -> v4l2_ctrl_handler_setup -> imx274_s_ctrl ->
imx274_set_exposure, where priv->mode_index is accessed before being
assigned.
This is wrong but does not trigger a visible bug because priv is
zero-initialized and 0 is the default value for priv->mode_index. But
this would become a crash in follow-up commits when mode_index is
replaced by a pointer that must always be valid.
Fix the bug before it shows up by initializing struct members early.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the ak7375 lens voice coil.
This is a voice coil module using the i2c bus to control the
focus position.
ak7375 can write multiple bytes of data at a time. If more
data is received instead of the stop condition after receiving
one byte of data, the address inside the chip is automatically
incremented and the data is written into the next address.
The ak7375 can control the position with 12 bits value and
consists of two 8 bit registers show as below:
register 0x00(AK7375_REG_POSITION):
+---+---+---+---+---+---+---+---+
|D11|D10|D09|D08|D07|D06|D05|D04|
+---+---+---+---+---+---+---+---+
register 0x01:
+---+---+---+---+---+---+---+---+
|D03|D02|D01|D00|---|---|---|---|
+---+---+---+---+---+---+---+---+
This driver support :
- set ak7375 to standby mode once suspend and
turn it back to active if resume
- set the position via V4L2_CID_FOCUS_ABSOLUTE ctrl
[Sakari Ailus: Rename val as ret in probe, drop redundant error message]
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add device tree bindings for AKM ak7375 voice coil lens
driver. This chip is used to drive a lens in a camera module.
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Driver must reject frame interval enumeration of unsupported resolution.
This was detected by v4l2-compliance format ioctl test:
v4l2-compliance Format ioctls:
info: found 2 frameintervals for pixel format 4745504a and size 176x144
fail: v4l2-test-formats.cpp(123):
found frame intervals for invalid size 177x144
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This sparse warning is emitted by using v4l2_find_nearest_size in some
cases. Fix it in the framework.
>> drivers/media/i2c/ov5640.c:1394:14: sparse: incorrect type in assignment
+(different base types) @@ expected struct ov5640_mode_info const *mode @@
+got ststruct ov5640_mode_info const *mode @@
drivers/media/i2c/ov5640.c:1394:14: expected struct ov5640_mode_info const
+*mode
drivers/media/i2c/ov5640.c:1394:14: got struct ov5640_mode_info const ( *<
+noident> )[9]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to ov5640 datasheet xvclk is allowed to be between 6 and 54 MHz.
I run a successful test with 27 MHz.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
The same fix was already applied to non-soc_camera version of ov772x
driver in the commit commit a024ee14cd ("media: ov772x: correct setting
of banding filter")
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the subdevice doesn't provide s_power core ops callback, the
v4l2_subdev_call for s_power returns -ENOIOCTLCMD. If the subdevice
doesn't have the special handling for its power saving mode, the s_power
isn't required. So -ENOIOCTLCMD from the v4l2_subdev_call should be
ignored.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The struct clk_init_data init variable is declared in the isp_xclk_init()
function so is an automatic variable allocated in the stack. But it's not
explicitly zero-initialized, so some init fields are left uninitialized.
This causes the data structure to have undefined values that may confuse
the common clock framework when the clock is registered.
For example, the uninitialized .flags field could have the CLK_IS_CRITICAL
bit set, causing the framework to wrongly prepare the clk on registration.
This leads to the isp_xclk_prepare() callback being called, which in turn
calls to the omap3isp_get() function that increments the isp dev refcount.
Since this omap3isp_get() call is unexpected, this leads to an unbalanced
omap3isp_get() call that prevents the requested IRQ to be later enabled,
due the refcount not being 0 when the correct omap3isp_get() call happens.
Fixes: 9b28ee3c91 ("[media] omap3isp: Use the common clock framework")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
DW9807 is a 10 bit DAC from Dongwoon, designed for linear
control of voice coil motor.
This driver creates a V4L2 subdevice and
provides control to set the desired focus.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Dongwoon DW9807 is a voice coil lens driver.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds Bingbu as additional maintainer, and both Tian Shu and Jian Xu
as reviewers for IPU3 CIO2 driver.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The final version of the COMPILE_TEST patch for this driver missed
one warning about suspend/resume functions that can now appear
on platforms that don't always set CONFIG_PM:
drivers/media/platform/omap3isp/isp.c:1008:13: error: 'isp_resume_modules' defined but not used [-Werror=unused-function]
static void isp_resume_modules(struct isp_device *isp)
^~~~~~~~~~~~~~~~~~
drivers/media/platform/omap3isp/isp.c:974:12: error: 'isp_suspend_modules' defined but not used [-Werror=unused-function]
static int isp_suspend_modules(struct isp_device *isp)
This marks the respective functions as __maybe_unused as an easy
workaround.
Fixes: 243131134b ("media: omap3isp: Allow it to build with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so that the
subdevice device node is created.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver is going to offer a V4L2 sub-device interface, so
changing the output data format and the frame interval on this sub-device
can be made anytime. However, these requests are preferred to fail while
the video stream on the device is active.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt() in subdev pad ops, the s_ctrl() for subdev control handler,
and the s_frame_interval() in subdev video ops could be called when the
device is under power saving mode. These callbacks for ov772x driver
cause updating H/W registers that will fail under power saving mode.
This avoids it by not apply any changes to H/W if the device is not powered
up. Instead the changes will be restored right after power-up.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver provides three V4L2 controls and the current value of
each control is saved as a variable in the private data structure.
We don't need to keep track of the current value by ourself, if we use
v4l2_ctrl returned from v4l2_ctrl_new_std() instead.
This is a preparatory change to avoid accessing registers under power
saving mode. This simplifies s_ctrl() by making it just return without
saving the current control value in private area when it is called under
power saving mode.
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This splits the s_frame_interval() in subdev video ops into selecting the
frame interval and setting up the registers.
This is a preparatory change to avoid accessing registers under power
saving mode.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on the v4l2 driver, calling s_power() could be nested. So the
actual transitions between power saving mode and normal operation mode
should only happen at the first power on and the last power off.
This adds an s_power() nesting counter and updates the power state if the
counter is modified from 0 to != 0 or from != 0 to 0.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver currently only supports legacy platform data probe.
This change enables device tree probing.
Note that the platform data probe can select auto or manual edge control
mode, but the device tree probling can only select auto edge control mode
for now.
[Sakari Ailus: Remove direct OF dependencies from device ID table]
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the ov772x driver obtains a clock with a specific consumer ID.
As there's a single clock for this driver, we could omit clock-names
property in device tree by passing NULL as a consumer ID to clk_get().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver uses "rstb-gpios" and "pwdn-gpios" for reset and
powerdown pins. However, using generic names for these gpios is
preferred. ("reset-gpios" and "powerdown-gpios" respectively)
There is only one mainline user for these gpios, so rename to generic
names.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Create a source pad and set the media controller type to the sensor.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver only works when the i2c controller have
I2C_FUNC_PROTOCOL_MANGLING. However, many i2c controller drivers don't
support it.
The reason that the ov772x requires I2C_FUNC_PROTOCOL_MANGLING is that
it doesn't support repeated starts.
This changes the reading ov772x register method so that it doesn't
require I2C_FUNC_PROTOCOL_MANGLING by calling two separated i2c messages.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of module being physically mounted upside down.
In this case, mirror and flip are enabled to fix captured images
orientation.
[Sakari Ailus: Use dev_fwnode() instead of accessing device's of_node]
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the rotation property to the list of optional properties
for the OV5640 camera sensor.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add HFLIP/VFLIP controls support by setting registers REG21/REG20.
Useless values in hardcoded mode sequences are removed and
remaining binning values are now set after mode sequence being set.
Note that due to BSI (Back Side Illuminated) technology, image capture
is physically mirrored, mirror logic is so inversed in REG21 register
to cancel this effect.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the "rotation" property to tell that the sensor is mounted upside
down. This reverses the behaviour of the VFLIP and HFLIP controls as well
as the pixel order.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the rotation property to list of optional properties for the smia
sensors.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sensors are occasionally mounted upside down to systems such as mobile
phones or tablets. In order to use such a sensor without having to turn
every image upside down, most camera sensors support reversing the readout
order by setting both horizontal and vertical flipping.
This patch documents the "rotation" property for camera sensors, mirroring
what is defined for displays in
Documentation/devicetree/bindings/display/panel/panel.txt .
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The __NEED_MEDIA_LEGACY_API define is 1) ugly and 2) dangerous
since it is all too easy for drivers to define it to get hold of
legacy defines. Instead just define what we need in media-device.c
which is the only place where we need the legacy define
(MEDIA_ENT_T_DEVNODE_UNKNOWN).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ycbcr_enc, quantization and xfer_func fields are __u16 and not enums.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Drop the '- .. row 1' lines to make it easier to add new rows to
the tables in the future without having to renumber these lines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 0866df8dff.
The v4l uAPI documentation [0] makes clear that in the case of interlaced
video (i.e: field is V4L2_FIELD_ALTERNATE) the height refers to the number
of lines in the field and not the number of lines in the full frame (which
is twice the field height for interlaced formats).
So the original height calculation was correct, and it shouldn't had been
changed by the mentioned commit.
[0]:https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/subdev-formats.html
Fixes: 0866df8dff ("[media] tvp5150: fix pad format frame height")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not required to implement job_ready().
Since this one is dummy, we can drop it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit f1a81afc98 ("[media] m2m: fix bad unlock balance")
removed the last use of v4l2_m2m_ops.lock and
v4l2_m2m_ops.unlock hooks. They are not actually
used anymore. Remove them.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As per the documentation, job_abort is not required
to wait until the current job finishes. It is redundant
to do so, as the core will perform the wait operation.
Remove the wait infrastructure completely.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, rga_buf_start_streaming() is expecting
pm_runtime_get_sync to return zero on success, which
is wrong.
As per the documentation, pm_runtime_get_sync increments
the device's usage counter and return its result.
This means it will typically return a positive integer
on success and a negative error code.
Therefore, rockchip-rga driver is currently unusable
failing to start_streaming in most cases. Fix it and
while here, cleanup the buffer return-to-core logic.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacob Chen <jacob-chen@iotwrt.com>
[hans.verkuil@cisco.com: fix line over 80 cols warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When checking a format for validity, the resolution is reset to 1280x720
whenever the pixel format is not supported. This behavior can mislead
user-space into believing that this is the only resolution supported,
and looks strange considering that if we try/set the same format with
just the pixel format changed to a valid one, the call will this time
succeed without altering the resolution.
Resolution is managed independently of the pixel format, so remove this
reset.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When dvb_register_adapter fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling dvb_register_adapter.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
[hans.verkuil@cisco.com: use pr_err and fix typo: adater -> adapter]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When snd_ctl_add fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling snd_ctl_add.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The check for a zero retval is redundant as all paths that lead to
this point have set retval to an error return value that is non-zero.
Remove the redundant check.
Detected by CoverityScan, CID#102589 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there is a schedulable job, v4l2_m2m_try_schedule() calls
v4l2_m2m_try_run(). This makes the unconditional v4l2_m2m_try_run()
called by v4l2_m2m_job_finish superfluous. Remove it.
Fixes: 7f98639def ("V4L/DVB: add memory-to-memory device helper framework for videobuf")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from rga_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from deinterlace_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from emmaprp_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from g2d_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from vpe_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from vim2m_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
