High Quality Video Data Plane is hardware IP dedicated
to video rendering. Compare to GPD (graphic planes) it
have better scaler capabilities.
HQVDP use VID layer to push data into hardware compositor
without going into DDR. From data flow point of view HQVDP
and VID are nested so HQVPD update/disable VID.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
stih407 SoC have a dedicated hardware cursor plane,
this patch enable it.
The hardware have a color look up table, fix it to
be able to use ARGB8888.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
For stih407 SoC enable the second mixer to get two CRTC.
Allow GPD planes and encoders to be connected to this new CRTC.
Cursor plane can only be set on first CRTC.
GPD clocks needed change the parent clock depending on which
CRTC GPD are used.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
The HDMI path introduce a delay of 6 pixels.
This delay should be take into account while programming
VTG for the HDMI. Without this delay, the HDMI active
window area is shift of 6 pixel on the right.
Set also timing for DVO output.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Change some functions prototype to prepare the introduction of
auxiliary crtc. It will also help to have a DVO encoder.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Make sure that vblank is enabled when crtc commit is call.
Replace drm_vblank_off() by drm_crtc_vblank_off()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
The hardware expect to have the infoframe checksum in the first byte.
In consequence shift all infoframe on one byte.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Store the physical address at node creation time
to avoid use of virt_to_dma and dma_to_virt everywhere
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
gpio used for HDMI hot plug detection is useless,
HDMI_STI register contains an hot plug detection status bit.
Fix binding documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Depending of the board configuration i2c for ddc could change,
this patch allow to use a phandle to specify which i2c controller to use.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Merge drm core fixes from Daniel.
* tag 'topic/core-stuff-2014-12-10' of git://anongit.freedesktop.org/drm-intel:
drm: Zero out DRM object memory upon cleanup
drm: fix a typo in a comment
drm: fix a word repetition in a comment
drm: Fix memory leak at error path of drm_read()
drm/Documentation: Fix rowspan value in drm-kms-properties
drm/edid: Restore kerneldoc consistency
drm/edid: new drm_edid_block_checksum helper function V3
drm/edid: shorten log output in case of all zeroes edid block
drm/edid: move drm_edid_is_zero to top, make edid argument const
Pull VFS changes from Al Viro:
"First pile out of several (there _definitely_ will be more). Stuff in
this one:
- unification of d_splice_alias()/d_materialize_unique()
- iov_iter rewrite
- killing a bunch of ->f_path.dentry users (and f_dentry macro).
Getting that completed will make life much simpler for
unionmount/overlayfs, since then we'll be able to limit the places
sensitive to file _dentry_ to reasonably few. Which allows to have
file_inode(file) pointing to inode in a covered layer, with dentry
pointing to (negative) dentry in union one.
Still not complete, but much closer now.
- crapectomy in lustre (dead code removal, mostly)
- "let's make seq_printf return nothing" preparations
- assorted cleanups and fixes
There _definitely_ will be more piles"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
copy_from_iter_nocache()
new helper: iov_iter_kvec()
csum_and_copy_..._iter()
iov_iter.c: handle ITER_KVEC directly
iov_iter.c: convert copy_to_iter() to iterate_and_advance
iov_iter.c: convert copy_from_iter() to iterate_and_advance
iov_iter.c: get rid of bvec_copy_page_{to,from}_iter()
iov_iter.c: convert iov_iter_zero() to iterate_and_advance
iov_iter.c: convert iov_iter_get_pages_alloc() to iterate_all_kinds
iov_iter.c: convert iov_iter_get_pages() to iterate_all_kinds
iov_iter.c: convert iov_iter_npages() to iterate_all_kinds
iov_iter.c: iterate_and_advance
iov_iter.c: macros for iterating over iov_iter
kill f_dentry macro
dcache: fix kmemcheck warning in switch_names
new helper: audit_file()
nfsd_vfs_write(): use file_inode()
ncpfs: use file_inode()
kill f_dentry uses
lockd: get rid of ->f_path.dentry->d_sb
...
We may be hidding bugs by doing that, so let remove it and have the
actual mask value shine through, for better or worse.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While trying to unify the order of those arguments throughout the
driver, Daniel noticed what we were inverting them in this part of the
code.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Drivers where the DRM objects have a lifetime that extends beyond that
of the DRM device need to zero out the DRM object memory to void stale
data such as properties. The DRM core code expects to operate on newly
allocated and zeroed out objects and will behave unexpectedly, such as
add duplicate properties, otherwise.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):
WA_SET_BIT_MASKED(GEN7_GT_MODE,
GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);
drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
(0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
[-Wshift-overflow]
WA_SET_BIT_MASKED(GEN7_GT_MODE,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
'WA_SET_BIT_MASKED'
WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)
Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.
The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.
To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.
This bug was introduced when reworking the WA emission in:
Commit 7225342ab5
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Oct 7 17:21:26 2014 +0300
drm/i915: Build workaround list in ring initialization
v2: Invert the order of the mask and value arguments (Daniel Vetter)
Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
_MASKED_FIELD() (Jani Nikula)
Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
Add check to ensure the value is within the mask boundaries (Chris Wilson)
v3: Ensure the the value and mask are 16 bits (Dave Gordon)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently stuff works that way on those machines.
I agree with Chris' concern that this is a bit risky but imo worth a
shot in -next just for fun. Afaics all these machines have the pci
resources allocated like that by the BIOS, so I suspect that it's all
ok.
This regression goes back to
commit eaba1b8f33
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Jul 4 12:28:35 2013 +0100
drm/i915: Verify that our stolen memory doesn't conflict
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76983
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71031
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds fbdev/con support for tiled monitors, so that we
only set a mode on the correct half of the monitor, or
span the two halves if needed.
v2: remove unneeded ERROR, fix | vs ||
Signed-off-by: Dave Airlie <airlied@redhat.com>
This takes the tiling info from the connector and
exposes it to userspace, as a blob object in a
connector property.
The contents of the blob is ABI.
v2: add property + function documentation.
v3: move property setup from previous patch.
add boilerplate + fix long line (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This creates a tile group from DisplayID block, and
stores the pieces of parsed info from the DisplayID block
into the connector.
v2: add missing signoff, add new connector bits to docs.
v3: remove some debugging.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logical ports are never going to have EDID changes,
they are used for the internal ports on MST monitors.
We cache the EDIDs from these to save time at MST probe.
v2: drop misplace tile property line, meant for other patch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
A tile group is an identifier shared by a single monitor,
DisplayID topology has 8 bytes we can use for this, just
use those for now until something else comes up in the
future. We assign these to an idr and use the idr to
tell userspace what connectors are in the same tile group.
DisplayID v1.3 says the serial number must be unique for
displays from the same manufacturer.
v2:
destroy idr (dvdhrm)
add docbook (danvet)
airlied:- not sure how to make docbook add fns to tile group section.
v3: fix missing unlock.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we unplug a dp mst branch we unreference the entire tree from
the root towards the leaves. Which is ok, since that's the way the
pointers and so also the refcounts go.
But when we drop the reference we must make sure that we remove the
branches/ports from the lists/pointers before dropping the reference.
Otherwise the get_validated functions will still return it instead
of returning NULL (which indicates a potentially on-going unplug).
The mst branch destroy gets this right for ports: First it deletes
the port from the ports list, then it unrefs. But the ports destroy
function gets it wrong: First it unrefs, then it drops the ref. Which
means a zombie mst branch can still be validate with get_validated_mstb_ref
when it shouldn't.
Fix this.
This should address a backtrace Dave dug out somewhere on unplug:
[<ffffffffa00cc262>] drm_dp_mst_get_validated_mstb_ref_locked+0x92/0xa0 [drm_kms_helper]
[<ffffffffa00cc211>] drm_dp_mst_get_validated_mstb_ref_locked+0x41/0xa0 [drm_kms_helper]
[<ffffffffa00cc2aa>] drm_dp_get_validated_mstb_ref+0x3a/0x60 [drm_kms_helper]
[<ffffffffa00cc2fb>] drm_dp_payload_send_msg.isra.14+0x2b/0x100 [drm_kms_helper]
[<ffffffffa00cc547>] drm_dp_update_payload_part1+0x177/0x360 [drm_kms_helper]
[<ffffffffa015c52e>] intel_mst_disable_dp+0x3e/0x80 [i915]
[<ffffffffa013d60b>] haswell_crtc_disable+0x1cb/0x340 [i915]
[<ffffffffa0136739>] intel_crtc_control+0x49/0x100 [i915]
[<ffffffffa0136857>] intel_crtc_update_dpms+0x67/0x80 [i915]
[<ffffffffa013fa59>] intel_connector_dpms+0x59/0x70 [i915]
[<ffffffffa015c752>] intel_dp_destroy_mst_connector+0x32/0xc0 [i915]
[<ffffffffa00cb44b>] drm_dp_destroy_port+0x6b/0xa0 [drm_kms_helper]
[<ffffffffa00cb588>] drm_dp_destroy_mst_branch_device+0x108/0x130 [drm_kms_helper]
[<ffffffffa00cb3cd>] drm_dp_port_teardown_pdt+0x3d/0x50 [drm_kms_helper]
[<ffffffffa00cdb79>] drm_dp_mst_handle_up_req+0x499/0x540 [drm_kms_helper]
[<ffffffff810d9ead>] ? trace_hardirqs_on_caller+0x15d/0x200 [<ffffffffa00cdc73>]
drm_dp_mst_hpd_irq+0x53/0xa00 [drm_kms_helper] [<ffffffffa00c7dfb>]
? drm_dp_dpcd_read+0x1b/0x20 [drm_kms_helper] [<ffffffffa0153ed8>]
? intel_dp_dpcd_read_wake+0x38/0x70 [i915] [<ffffffffa015a225>]
intel_dp_check_mst_status+0xb5/0x250 [i915] [<ffffffffa015ac71>]
intel_dp_hpd_pulse+0x181/0x210 [i915] [<ffffffffa01104f6>]
i915_digport_work_func+0x96/0x120 [i915]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
On MST systems the monitors don't appear when we set the fb up,
but plymouth opens the drm device and holds it open while they
come up, when plymouth finishes and lastclose gets called we
don't do the delayed fb probe, so the monitor never appears on the
console.
Fix this by moving the delayed checking into the mode restore.
v2: Daniel suggested that ->delayed_hotplug is set under
the mode_config mutex, so we should check it under that as
well, while we are in the area.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least on two MST devices I've tested with, when
they are link training downstream, they are totally
unable to handle aux ch msgs, so they defer like nuts.
I tried 16, it wasn't enough, 32 seems better.
This fixes one Dell 4k monitor and one of the
MST hubs.
v1.1: fixup comment (Tom).
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise the MST resume paths can hit DPMS paths
which hit state checker paths, which hit WARN_ON,
because the state checker is inconsistent with the
hw.
This fixes a bunch of WARN_ON's on resume after
undocking.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Merge rockchip GPU support.
This has a branch in common with the iommu tree, hopefully the
process works.
* 'drm_iommu_v15' of https://github.com/markyzq/kernel-drm-rockchip:
dt-bindings: video: Add documentation for rockchip vop
dt-bindings: video: Add for rockchip display subsytem
drm: rockchip: Add basic drm driver
dt-bindings: iommu: Add documentation for rockchip iommu
iommu/rockchip: rk3288 iommu driver
As discussed on irc, I'm sending a pull request with one important change:
- Disable support for 32-bit user processes. This is done due to AMD's decision
to remove support for 32-bit user processes on Linux for its HSA stack.
* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
amdkfd: Disable support for 32-bit user processes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhNLZAAoJEHm+PkMAQRiGAEcH/iclYDW7k2GKemMqboy+Ohmh
+ELbQothNhlGZlS1wWdD69LBiiXkkQ+ufVYFh/hC0oy0gUdfPMt5t+bOHy6cjn6w
9zOcACtpDKnqbOwRqXZjZgNmIabk7lRjbn7GK4GQqpIaW4oO0FWcT91FFhtGSPDa
tjtmGRqDmbNsqfzr18h0WPEpUZmT6MxIdv17AYDliPB1MaaRuAv1Kss05TJrXdfL
Oucv+C0uwnybD9UWAz6pLJ3H/HR9VJFdkaJ4Y0pbCHAuxdd1+swoTpicluHlsJA1
EkK5iWQRMpcmGwKvB0unCAQljNpaJiq4/Tlmmv8JlYpMlmIiVLT0D8BZx5q05QQ=
=oGNw
-----END PGP SIGNATURE-----
Merge tag 'v3.18' into drm-next
Linux 3.18
Backmerge Linus tree into -next as we had conflicts in i915/radeon/nouveau,
and everyone was solving them individually.
* tag 'v3.18': (57 commits)
Linux 3.18
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
uapi: fix to export linux/vm_sockets.h
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
ahci: disable MSI on SAMSUNG 0xa800 SSD
context_tracking: Restore previous state in schedule_user
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/nouveau/nouveau_drm.c
drivers/gpu/drm/radeon/radeon_cs.c
This patch checks if the process that opens the /dev/kfd device is 32-bit
process. If so, it returns -EPERM and prints a warning message in dmesg.
This is done to prevent 32-bit user processes from using amdkfd, and hence, HSA
features.
AMD's HSA userspace stack will also support only 64-bit processes on Linux.
Reviewed-by: Alexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
So apparently jiffies<->nsec<->ktime isn't accurate or something. At
elast if we timeout there's occasionally still a few hundred us left
(in a 2 second timeout).
Stuff I've tried and thrown out again:
- Sampling the before timestamp before jiffies. Doesn't improve test
path rate at all.
- Using jiffies. Way to inaccurate, which means way too much drift
with signals plus automatic ioctl restarting in userspace. In
hindsight we should have used an absolute timeout, but hey we need
something for v3 of the i915 gem wait interfaces ;-)
- Trying to figure out where accuracy gets lost. gl testcase really
don't care all that much about this (as long as isn't not massively
off), it's just that the testcase gets a bit upset if it receives an
EITME with timeout > 0.
So as long as we're in the ballbark it's good enough. So patch
everything up if we're at most one jiffies off. I get's me a solid
test again.
This regression is probably introduced in
commit 5ed0bdf21a
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Wed Jul 16 21:05:06 2014 +0000
drm: i915: Use nsec based interfaces
Use ktime_get_raw_ns() and get rid of the back and forth timespec
conversions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Probably because I'm too lazy to confirm myself and still waiting for
QA ;-)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We've lost the +1 required for correct timeouts in
commit 5ed0bdf21a
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Wed Jul 16 21:05:06 2014 +0000
drm: i915: Use nsec based interfaces
Use ktime_get_raw_ns() and get rid of the back and forth timespec
conversions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: John Stultz <john.stultz@linaro.org>
So fix this up by reinstating our handrolled _timeout function. While
at it bother with handling MAX_JIFFIES.
v2: Convert to usecs (we don't care about the accuracy anyway) first
to avoid overflow issues Dave Gordon spotted.
v3: Drop the explicit MAX_JIFFY_OFFSET check, usecs_to_jiffies should
take care of that already. It might be a bit too enthusiastic about it
though.
v4: Chris has a much nicer color, so use his implementation.
This requires to export nsec_to_jiffies from time.c.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.
* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Fixes for 3.20. I did stick the gen3/4 reset work from Ville in because we
have an awful lot of gen4 mesa hangs, and with this reset should also work
on vintage i965g/gm (we already have reset for g4x/gen4.5). So should help
to appease users suffering from these hangs. Otherwise all over.
This is the last 3.20 pull from me, from here on Jani will take over. By Ville Syrjälä (8) and others
* tag 'drm-intel-next-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Reject modeset when the same digital port is used more than once
drm/i915: mask RPS IRQs properly when disabling RPS
drm/i915: Tune down spurious CRC interrupt warning
drm/i915: Fix context object leak for legacy contexts
drm/i915/skl: Update in Gen9 multi-engine forcewake range
drm/i915/eDP: When enabling panel VDD cancel pending disable worker
drm/i915: Handle runtime pm in the CRC setup code
drm/i915: Disable crtcs gracefully before GPU reset on gen3/4
drm/i915: Grab modeset locks for GPU rest on pre-ctg
drm/i915: Implement GPU reset for g33
drm/i915: Implement GPU reset for 915/945
drm/i915: Restore the display config after a GPU reset on gen4
drm/i915: Fix gen4 GPU reset
drm/i915: Stop gathering error states for CS error interrupts
drm/i915: Disallow pin ioctl completely for kms drivers
drm/i915: Only warn the first time we attempt to mmio whilst suspended
drm/i915/chv: Enable AVI, SPD and HDMI infoframes for CHV.
drm/i915: Don't clobber crtc->new_config when nothing changes
Just three more fixes for 3.19.
This is the last request until -rc1. I will have our QA team run a full
HSA stack test on 3.19-rc1 and if we find problems, I will send a fixes pull
request.
* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
amdkfd: Set *buffer_ptr to NULL in case of error
amdkfd: use atomic allocations within srcu callbacks
amdkfd: use sizeof(long) granularity for the pasid bitmask
Note that the read manpages explicitly states that the read position
is undefined on error. Since EFAULT is just a userspace bug we are
therefore fine with just dropping the event on the floor.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[danvet: Add note that just dropping the event is ok.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In function acquire_packet_buffer() we may return -ENOMEM. In that case, we
should set the *buffer_ptr to NULL, so that calling functions which check the
*buffer_ptr value as a criteria for success, will know that
acquire_packet_buffer() failed.
Reviewed-by: Alexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
This seems to work well on CI boards after fixing the
last few bugs noticed by Chernovsky Oleg.
On boards with a high default fan speed this should
reduce fan noise. Manual fan control is not enabled
yet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in 4 files under
gpu/drm/exynos/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Nobody is interested at which index the chunk is. What's needed is
a pointer to the chunk. Remove unused chunk_id field as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Completely unnecessary since the ww_mutex used to reserve a buffer
can detect double reservations from the same thread anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds an optional list_head parameter to ttm_eu_reserve_buffers.
If specified duplicates in the execbuf list are no longer reported as errors,
but moved to this list instead.
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the that ring we are using for copies is functional
rather than the GFX ring. On newer asics we use the DMA
ring for bo moves.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Since we are now preserving the cursor across modesets, the cursor could
be left over in console if e.g. X crashed.
v2: add comment about universal plane support
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stop using the VM mutex for this
v2: fix typo in comment
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The BO_VA contains everything necessary.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Better match what it is actually doing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only used for duplicate check and that
can be done on the original as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only used once after initializing and that
ptr can be calculated from the BO as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only needed in radeon_crtc_cursor_set2.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Setting a mode seems to clear the cursor registers, so we need to
re-program them to make sure the cursor is visible.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 18df89fef2 ("drm: Decouple EDID parsing from I2C adapter")
renamed the adapter parameter of the drm_do_probe_ddc_edid function
to data but didn't update the kerneldoc accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
srcu callbacks are running in atomic context, we can't allocate using
__GFP_WAIT.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
All the bit operations (such as find_first_zero_bit()) read sizeof(long) bytes
at a time. If we allocated less than sizeof(long) bytes for the bitmask we
would be accessing invalid memory when working with the bitmask.
Change the allocator to allocate sizeof(long) multiples for the bitmask.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
This codepath is mostly hit when rebinding after a backup buffer swapout. It's
amazing that this error hasn't been more obvious but probably the shaders are
not reread from guest memory that often..
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The commit "vmwgfx: Rework fence event action" introduced a number of bugs
that are fixed with this commit:
a) A forgotten return stateemnt.
b) An if statement with identical branches.
Cc: <stable@vger.kernel.org>
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Kernel side fence objects are used when unbinding resources and may thus be
created as part of a memory reclaim operation. This might trigger recursive
memory reclaims and result in the kernel running out of stack space.
So a simple way out is to avoid accounting of these fence objects.
In principle this is OK since while user-space can trigger the creation of
such objects, it can't really hold on to them. However, their lifetime is
quite long, so some form of accounting should perhaps be implemented in the
future.
Fixes kernel crashes when running, for example viewperf11 ensight-04 test 3
with low system memory settings.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The function vmw_master_check() might return -ERESTARTSYS if there is a
signal pending, indicating that the IOCTL should be rerun, potentially from
user-space. At that point we shouldn't print out an error message since that
is not an error condition. In short, avoid bloating the kernel log when a
process refuses to die on SIGTERM.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
On pre-HSW we have two encoders per digital port: one HDMI, one DP.
However they are the same physical port in hardware and we can't enable
both at the same time. Reject the modeset if the user attempts this.
So far we've been saved by the fact that we never see both HDMI and DP
connectors as connected. But if the user decides to force a mode anyway,
all kinds of funny stuff might happen.
Unfortunately we don't seem to have any way to inform userspace that
such configurations are invalid except by returning an error from
setcrtc. possible_clones only covers real cloning situations, and
looking at the connector names doesn't work either since we don't
always register both connectors for the same port. I suppose the
only way to fix that would be to expose only a single encoder per
digital port like we do on HSW+ but that would be a fairly large
undertaking for little gain.
kms_setmode hits this since it forces modes on non-connected VGA and
HDMI connectors. Previosuly it just resulted in weirdness such as
failed link training. With this patch it will now get an error back
from the kernel and will die with an assert since it thinks that the
configuration should be fine.
v2: Deal with INTEL_OUTPUT_UNKNOWN (Paulo)
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, igt/gem_reset_stats can trigger the recently added WARN on
left-over PM_IIR bits in gen6_enable_rps_interrupts(). There are two
reasons for this:
1. we call intel_enable_gt_powersave() without a preceeding
intel_disable_gt_powersave()
2. gen6_disable_rps_interrupts() doesn't mask interrupts in PM_IMR
1. means RPS interrupts will remain enabled and can be serviced during
the HW initialization after a GPU reset. 2. means even if we called
gen6_disable_rps_interrupts() any new RPS interrupt during RPS
initialization would still propagate to PM_IIR too early (though
wouldn't be serviced).
This patch solves the 2. issue by also masking interrupts in PM_IMR, the
following patch fixes 1. getting rid of the WARN. This also makes
intel_enable_gt_powersave() and intel_disable_gt_powersave() more
symmetric.
Since gen6_disable_rps_interrupts() is called during driver loading with
i915 interrupts disabled add a new version of gen6_disable_pm_irq() that
doesn't WARN for this.
Also while at it, get the irq_lock around the whole PM_IMR/IER/IIR
programming sequence and make sure that any queued PM_IIR bit is also
cleared.
The WARN was caught by PRTS after I sent my previous RPS sanitizing
patchset and I could easily reproduce it on HSW. To actually fix it we
also need the next patch.
Reported-by: He, Shuang <shuang.he@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't really synchronously turn them off from debugfs. We try to
avoid hitting them too badly by waiting one vblank, but apparently the
irq handler can still race through that gap.
Since this isn't really all that important for testcases, only for
debugging CRC issues let's tune it down to a debug message.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82602
Cc: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Dynamic context pinning for LRCs introduced a leak in legacy mode.
Reinstate context unreference in i915_gem_free_request for legacy contexts.
Leak reported by i-g-t/drv_module_reload fixed by this patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86507
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: John Harrison<John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updates in forcewake range for Render/Media/Common
power wells for Gen9.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before testing if the panel VDD is enabled on eDP cancel any pending
disable worker. This makes sure the worker will be triggered with a
delay from the last time edp_panel_vdd_schedule_off() is called, not
the first time. This avoids unnecessary overhead.
https://bugs.freedesktop.org/show_bug.cgi?id=86201
v2: use cancel_delayed_work() instead of cancel_delayed_work_sync()
as the pps_mutexes will provide the required serialization with
edp_panel_vdd_work() while the sync variant may deadlock. Suggested
by Ville Syrjälä <ville.syrjala@linux.intel.com>.
Made commit message a bit clearer.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The crc code doesn't handle anything really that could drop the
register state (by design so that we have less complexity). Which
means userspace may only start crc capture once the pipe is fully set
up.
With an i-g-t patch this will be the case, but there's still the
problem that this results in obscure unclaimed register write
failures. Which is a pain to debug.
So instead make sure we don't have the basic unclaimed register write
failure by grabbing runtime pm references. And reject completely
invalid requests with -EIO. This is still racy of course, but for a
test library we don't really care - if userspace shuts down the pipe
right afterwards the entire setup will be lost anyway.
v2: Put instead of get, spotted by Damien. Also explain the runtime pm
dance.
v3: There's really no need for rpm get/put since power_is_enabled only
checks software state (Damien).
References: https://bugs.freedesktop.org/show_bug.cgi?id=86092
Cc: Damien Lespiau <damien.lespiau@intel.com> (v2)
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The GPU reset also resets the display on gen3/4. The g33 docs say we
should disable all planes before flipping the reset switch. Just
disable all the crtcs instead. That seems a nicer thing to do anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen4 and earlier the GPU reset also resets the display, so we should
protect against concurrent modeset operations. Grab all the modeset locks
around the entire GPU reset dance, remebering first ti dislogde any
pending page flip to make sure we don't deadlock. Any pageflip coming
in between these two steps should fail anyway due to reset_in_progress,
so this should be safe.
This fixes a lot of failed asserts in the modeset code when there's a
modeset racing with the reset. Naturally the asserts aren't happy when
the expected state has disappeared.
v2: Drop UMS checks, complete pending flips after the reset (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
g33 seems to sit somewhere between the 915/945/965 style and the
g4x style. The bits look like g4x, but we still need to do a full
reset including display.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg GPU reset also resets the display hardware. Force a mode
restore after the GPU reset, and also re-init clock gating.
v2: Use intel_modeset_init_hw() instead of intel_init_clock_gating()
in case more relevant stuff gets added there at some point
Restore interrupts after the reset as well
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg the reset bit directly controls the reset signal. We must
assert it for >=20usec and then deassert it. Bit 1 is a RO status bit
which should also go down when the reset is no longer asserted.
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's quite a few bug reports with error states where the error
reasons makes just about no sense at all. Like dying on tlbs for a
display plane that's not even there. Also users don't really report a
lot of bad side effects generally, just the error states.
Furthermore we don't even enable these interrupts any more on gen5+
(though the handling code is still there). So this mostly concerns old
platforms.
Given all that lets make our lives a bit easier and stop capturing
error states, in the hopes that we can just ignore them. In case
that's not true and the gpu indeed dies the hangcheck should
eventually kick in. And I've left some debug log in to make this case
noticeble. Referenced bug is just an example.
v2: Fix missing \n Jani spotted.
References: https://bugs.freedesktop.org/show_bug.cgi?id=82095
References: https://bugs.freedesktop.org/show_bug.cgi?id=85944
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The problem here is that SNA pins batchbuffers to etch out a bit more
performance. Iirc it started out as a w/a for i830M (which we've
implemented in the kernel since a long time already). The problem is
that the pin ioctl wasn't added in
commit d23db88c3a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri May 23 08:48:08 2014 +0200
drm/i915: Prevent negative relocation deltas from wrapping
Fix this by simply disallowing pinning from userspace so that the
kernel is in full control of batch placement again. Especially since
distros are moving towards running X as non-root, so most users won't
even be able to see any benefits.
UMS support is dead now, but we need this minimal patch for
backporting. Follow-up patch will remove the pin ioctl code
completely.
Note to backporters: You must have both
commit b45305fce5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Dec 17 16:21:27 2012 +0100
drm/i915: Implement workaround for broken CS tlb on i830/845
which laned in 3.8 and
commit c4d69da167
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Sep 8 14:25:41 2014 +0100
drm/i915: Evict CS TLBs between batches
which is also marked cc: stable. Otherwise this could introduce a
regression by disabling the userspace w/a without the kernel w/a being
fully functional on i830/45.
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554#c116
Cc: stable@vger.kernel.org # requires c4d69da167 and v3.8
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In all likelihood we will do a few hundred errnoneous register
operations if we do a single invalid register access whilst the device
is suspended. As each instance causes a WARN, this floods the system
logs and can make the system unresponsive.
The warning was first introduced in
commit b2ec142cb0
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Feb 21 13:52:25 2014 -0300
drm/i915: call assert_device_not_suspended at gen6_force_wake_work
and despite the claims the WARN is still encountered in the wild today.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV infoframes were not being enabled.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When doing a nop modeset we currently leave crtc->new_config point at
the already freed temporary pipe_config. That will anger the sanity
checks in intel_modeset_update_state() when the nop modeset gets
followed by a GPU reset on gen3/4 where the display block gets fully
reinitialized during the reset.
So leave crtc->new_config alone until we know a modeset is actually
required.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DRM connector's encoder pointer is managed internally by the DRM
core and set to NULL when the DRM connector is disconnected from the
CRTC it was attached to. This results in a NULL pointer dereference in
the HDMI connector functions when trying to call the associated slave
encoder's operations.
Fix this by retrieving the slave encoder pointer from the R-Car
connector structure instead of the DRM connector structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm-intel-next-2014-11-21:
- infoframe tracking (for fastboot) from Jesse
- start of the dri1/ums support removal
- vlv forcewake timeout fixes (Imre)
- bunch of patches to polish the rps code (Imre) and improve it on bdw (Tom
O'Rourke)
- on-demand pinning for execlist contexts
- vlv/chv backlight improvements (Ville)
- gen8+ render ctx w/a work from various people
- skl edp programming (Satheeshakrishna et al.)
- psr docbook (Rodrigo)
- piles of little fixes and improvements all over, as usual
* tag 'drm-intel-next-2014-11-21-fixed' of git://anongit.freedesktop.org/drm-intel: (117 commits)
drm/i915: Don't pin LRC in GGTT when dumping in debugfs
drm/i915: Update DRIVER_DATE to 20141121
drm/i915/g4x: fix g4x infoframe readout
drm/i915: Only call mod_timer() if not already pending
drm/i915: Don't rely upon encoder->type for infoframe hw state readout
drm/i915: remove the IRQs enabled WARN from intel_disable_gt_powersave
drm/i915: Use ggtt error obj capture helper for gen8 semaphores
drm/i915: vlv: increase timeout when setting idle GPU freq
drm/i915: vlv: fix cdclk setting during modeset while suspended
drm/i915: Dump hdmi pipe_config state
drm/i915: Gen9 shadowed registers
drm/i915/skl: Gen9 multi-engine forcewake
drm/i915: Read power well status before other registers for drpc info
drm/i915: Pin tiled objects for L-shaped configs
drm/i915: Update ring freq for full gpu freq range
drm/i915: change initial rps frequency for gen8
drm/i915: Keep min freq above floor on HSW/BDW
drm/i915: Use efficient frequency for HSW/BDW
drm/i915: Can i915_gem_init_ioctl
drm/i915: Sanitize ->lastclose
...
Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.
v2: rebased on Alex current drm-fixes-3.18
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Original code sent always 0 as the index number of the node. This patch fixes
this bug by sending a variable which is incremented per node.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
This patch fixes a device QCM bug, where the number of queues were not
counted correctly for the operation of update queue. The count was incorrect
as there was no regard to the previous state of the queue.
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
LRC object does not need to be mapped into the GGTT when dumping. A side-effect
of this patch is that a compiler warning goes away (not checking return value
of i915_gem_obj_ggtt_pin).
v2: Broke out individual context dumping into a new function as the indentation
was getting a bit crazy. Added notification of contexts with no gem object for
debugging purposes. Removed unnecessary pin_pages and unpin_pages, replaced
with explicit get_pages for the context object as there may be no backing store
allocated at this time (Comment for get_pages says "Ensure that the associated
pages are gathered from the backing storage and pinned into our object").
Improved error checking - get_pages and get_page are checked for failure.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Align paramter continuation lines properly. Also add some
braces to the nested loops again for readability.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in
commit c31407a367
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Oct 18 21:07:01 2012 +0100
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch adds the basic structure of a DRM Driver for Rockchip Socs.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Apparently PCH fifo underruns are tricky, we have plenty reports that
we see the occasional underrun (especially at boot-up).
So for a change let's see what happens when we don't re-enable pch
fifo underrun reporting when the pipe is disabled. This means that the
kernel can't catch pch fifo underruns when they happen (except when
all pipes are on on the pch). But we'll still catch underruns when
disabling the pipe again. So not a terrible reduction in test
coverage.
Since the DRM_ERROR is new and hence a regression plan B would be to
revert it back to a debug output. Which would be a lot worse than this
hack for underrun test coverage in the wild. See the referenced
discussions for more.
References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=86233
References: https://bugs.freedesktop.org/show_bug.cgi?id=86478
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
