* 'fixes-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix deadlock in worker_maybe_bind_and_lock()
workqueue: Document debugging tricks
Fix up trivial spelling conflict in kernel/workqueue.c
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86, nmi: Move LVT un-masking into irq handlers
perf events, x86: Work around the Nehalem AAJ80 erratum
perf, x86: Fix BTS condition
ftrace: Build without frame pointers on Microblaze
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Configure IOAPIC pins for USB and SATA to level type
x86: devicetree: Configure IOAPIC pin only once
x86, setup: When probing memory with e801, use ax/bx as a pair
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (lm85) Fix error paths in probe function
hwmon: (lm85) Add missing list terminators
hwmon: (adm1021) Clarify documentation regarding Xeon processors
hwmon: (lm90) Fix update interval information in driver documentation
hwmon: (lm90) Add support for ADT7461A and NCT1008
If a rescuer and stop_machine() bringing down a CPU race with each
other, they may deadlock on non-preemptive kernel. The CPU won't
accept a new task, so the rescuer can't migrate to the target CPU,
while stop_machine() can't proceed because the rescuer is holding one
of the CPU retrying migration. GCWQ_DISASSOCIATED is never cleared
and worker_maybe_bind_and_lock() retries indefinitely.
This problem can be reproduced semi reliably while the system is
entering suspend.
http://thread.gmane.org/gmane.linux.kernel/1122051
A lot of kudos to Thilo-Alexander for reporting this tricky issue and
painstaking testing.
stable: This affects all kernels with cmwq, so all kernels since and
including v2.6.36 need this fix.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Tested-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Cc: stable@kernel.org
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3+: voltage: remove initial voltage
OMAP4: Intialize IVA Device in addition to DSP device.
omap: rx51: mark reserved memory earlier
OMAP3: l3: fix for "irq 10: nobody cared" message
arm: omap2: enable smc instruction for sleep34xx
OMAP2/3: hwmod: fix gpio-reset timeouts seen during bootup.
OMAP3: PM: Do not rely on ROM code to restore CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL
OMAP2+: PM: Fix the saving of CM_AUTOIDLE_PLL register on scratchpad area
OMAP4: clock data: Change DSS clock aliases
OMAP2+: hwmod data: Fix wrong dma_system end address
We must remove all files we created, even in error cases.
Fixes second part of kernel bug #34072:
https://bugzilla.kernel.org/show_bug.cgi?id=34072
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Recent Xeon processor thermal sensors are supported by the coretemp
driver and not the adm1021 driver. Only one old generation of Xeon
processors (the first Netburst ones) are supported by the adm1021
driver.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The lm90 driver's attribute update interval is configurable.
Reflect this information in the driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Sedat and Bruno reported RCU stalls which turned out to be caused by
the following;
sched_init() calls init_rt_bandwidth() which calls hrtimer_init()
_BEFORE_ hrtimers_init() is called. While not entirely correct this
worked because hrtimer_init() only accessed statically initialized
data (hrtimer_bases.clock_base[CLOCK_MONOTONIC])
Commit e06383db9 (hrtimers: extend hrtimer base code to handle more
then 2 clockids) added an indirection to the hrtimer_bases.clock_base
lookup to avoid gap handling in the hot path. The table which is used
for the translataion from CLOCK_ID to HRTIMER_BASE index is
initialized at runtime in hrtimers_init(). So the early call of the
scheduler code translates CLOCK_MONOTONIC to HRTIMER_BASE_REALTIME.
Thus the rt_bandwith timer ends up on CLOCK_REALTIME. If the timer is
armed and the wall clock time is set (e.g. ntpdate in the early boot
process - which also gives the problem deterministic behaviour
i.e. magic recovery after N hours), then the timer ends up with an
expiry time far into the future. That breaks the RT throttler
mechanism as rt runtime is accumulated and never cleared, so the rt
throttler detects a false cpu hog condition and blocks all RT tasks
until the timer finally expires. That in turn stalls the RCU thread of
TINYRCU which leads to an huge amount of RCU callbacks piling up.
Make the translation table statically initialized, so we are back to
the status of <= 2.6.39.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: John stultz <johnstul@us.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1104282353140.3005%40ionos%3E
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: restore only the mode of this driver on lastclose (v2)
drm/radeon/kms: add info query for tile pipes
drm/radeon/kms: add missing safe regs for 6xx/7xx
drm: select FRAMEBUFFER_CONSOLE_PRIMARY if we have FRAMEBUFFER_CONSOLE
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
nfs: don't lose MS_SYNCHRONOUS on remount of noac mount
NFS: Return meaningful status from decode_secinfo()
NFSv4: Ensure we request the ordinary fileid when doing readdirplus
NFSv4: Ensure that clientid and session establishment can time out
SUNRPC: Allow RPC calls to return ETIMEDOUT instead of EIO
NFSv4.1: Don't loop forever in nfs4_proc_create_session
NFSv4: Handle NFS4ERR_WRONGSEC outside of nfs4_handle_exception()
NFSv4.1: Don't update sequence number if rpc_task is not sent
NFSv4.1: Ensure state manager thread dies on last umount
SUNRPC: Fix the SUNRPC Kerberos V RPCSEC_GSS module dependencies
NFS: Use correct variable for page bounds checking
NFS: don't negotiate when user specifies sec flavor
NFS: Attempt mount with default sec flavor first
NFS: flav_array honors NFS_MAX_SECFLAVORS
NFS: Fix infinite loop in gss_create_upcall()
Don't mark_inode_dirty_sync() while holding lock
NFS: Get rid of pointless test in nfs_commit_done
NFS: Remove unused argument from nfs_find_best_sec()
NFS: Eliminate duplicate call to nfs_mark_request_dirty
NFS: Remove dead code from nfs_fs_mount()
With transparent hugepage support, handle_mm_fault() has to be careful
that a normal PMD has been established before handling a PTE fault. To
achieve this, it used __pte_alloc() directly instead of pte_alloc_map as
pte_alloc_map is unsafe to run against a huge PMD. pte_offset_map() is
called once it is known the PMD is safe.
pte_alloc_map() is smart enough to check if a PTE is already present
before calling __pte_alloc but this check was lost. As a consequence,
PTEs may be allocated unnecessarily and the page table lock taken. Thi
useless PTE does get cleaned up but it's a performance hit which is
visible in page_test from aim9.
This patch simply re-adds the check normally done by pte_alloc_map to
check if the PTE needs to be allocated before taking the page table lock.
The effect is noticable in page_test from aim9.
AIM9
2.6.38-vanilla 2.6.38-checkptenone
creat-clo 446.10 ( 0.00%) 424.47 (-5.10%)
page_test 38.10 ( 0.00%) 42.04 ( 9.37%)
brk_test 52.45 ( 0.00%) 51.57 (-1.71%)
exec_test 382.00 ( 0.00%) 456.90 (16.39%)
fork_test 60.11 ( 0.00%) 67.79 (11.34%)
MMTests Statistics: duration
Total Elapsed Time (seconds) 611.90 612.22
(While this affects 2.6.38, it is a performance rather than a functional
bug and normally outside the rules -stable. While the big performance
differences are to a microbench, the difference in fork and exec
performance may be significant enough that -stable wants to consider the
patch)
Reported-by: Raz Ben Yehuda <raziebe@gmail.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@kernel.org> [2.6.38.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In corner cases where softlockup watchdog is not setup successfully, the
relevant nmi perf event for hardlockup watchdog could be disabled, then
the status of the underlying hardware remains unchanged.
Also, if the kthread doesn't start then the hrtimer won't run and the
hardlockup detector will falsely fire.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases gcc >= 4.5.2 will optimize away current_thread_info(). To
prevent gcc from doing so the stack address has to be obtained via inline
asm.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make HoneyPot ProcFS depend on CONFIG_PROC_FS so that it will build.
Recommended by Christoph Hellwig.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=33692
Reported-by: Simon Danner <danner.simon@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for 64 bit atomic operations on 32 bit UML systems. XFS
needs them since 2.6.38.
$ make ARCH=um SUBARCH=i386
...
LD .tmp_vmlinux1
fs/built-in.o: In function `xlog_regrant_reserve_log_space':
xfs_log.c:(.text+0xd8584): undefined reference to `atomic64_read_386'
xfs_log.c:(.text+0xd85ac): undefined reference to `cmpxchg8b_emu'
...
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=32812
Reported-by: Martin Walch <walch.martin@web.de>
Tested-by: Martin Walch <walch.martin@web.de>
Cc: Martin Walch <walch.martin@web.de>
Cc: <stable@kernel.org> [2.6.38.x 084189a: um: disable CONFIG_CMPXCHG_LOCAL]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PTE pages eat up memory just like anything else, but we do not account for
them in any way in the OOM scores. They are also _guaranteed_ to get
freed up when a process is OOM killed, while RSS is not.
Reported-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org> [2.6.36+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 569b846d ("memcg: coalesce uncharge during unmap/truncate"), we do
batched (delayed) uncharge at truncation/unmap. And since cdec2e42(memcg:
coalesce charging via percpu storage), we have percpu cache for
res_counter.
These changes improved performance of memory cgroup very much, but made
res_counter->usage usually have a bigger value than the actual value of
memory usage. So, *.usage_in_bytes, which show res_counter->usage, are
not desirable for precise values of memory(and swap) usage anymore.
Instead of removing these files completely(because we cannot know
res_counter->usage without them), this patch updates the meaning of those
files.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The huge_memory.c THP page fault was allowed to run if vm_ops was null
(which would succeed for /dev/zero MAP_PRIVATE, as the f_op->mmap wouldn't
setup a special vma->vm_ops and it would fallback to regular anonymous
memory) but other THP logics weren't fully activated for vmas with vm_file
not NULL (/dev/zero has a not NULL vma->vm_file).
So this removes the vm_file checks so that /dev/zero also can safely use
THP (the other albeit safer approach to fix this bug would have been to
prevent the THP initial page fault to run if vm_file was set).
After removing the vm_file checks, this also makes huge_memory.c stricter
in khugepaged for the DEBUG_VM=y case. It doesn't replace the vm_file
check with a is_pfn_mapping check (but it keeps checking for VM_PFNMAP
under VM_BUG_ON) because for a is_cow_mapping() mapping VM_PFNMAP should
only be allowed to exist before the first page fault, and in turn when
vma->anon_vma is null (so preventing khugepaged registration). So I tend
to think the previous comment saying if vm_file was set, VM_PFNMAP might
have been set and we could still be registered in khugepaged (despite
anon_vma was not NULL to be registered in khugepaged) was too paranoid.
The is_linear_pfn_mapping check is also I think superfluous (as described
by comment) but under DEBUG_VM it is safe to stay.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=33682
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Caspar Zhang <bugs@casparzhang.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: <stable@kernel.org> [2.6.38.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Azurit reports large increases in system time after 2.6.36 when running
Apache. It was bisected down to a892e2d7dc ("vfs: use kmalloc()
to allocate fdmem if possible").
That patch caused the vfs to use kmalloc() for very large allocations and
this is causing excessive work (and presumably excessive reclaim) within
the page allocator.
Fix it by falling back to vmalloc() earlier - when the allocation attempt
would have been considered "costly" by reclaim.
Reported-by: azurIt <azurit@pobox.sk>
Tested-by: azurIt <azurit@pobox.sk>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use io_apic_setup_irq_pin() in order to configure pin's interrupt
number polarity and type. This is done on every irq_create_of_mapping()
which happens for instance during pci enable calls. Level typed
interrupts are masked by default, edge are unmasked.
On the first ->xlate() call the level interrupt is configured and
masked. The driver calls request_irq() and the line is unmasked. Lets
assume the interrupt line is shared with another device and we call
pci_enable_device() for this device. The ->xlate() configures the pin
again and it is masked. request_irq() does not unmask the line because
it _is_ already unmasked according to its internal state. So the
interrupt will never be unmasked again.
This patch is based on an earlier work by Torben Hohn and solves the
problem by configuring the pin only once. Since all devices must agree
on the same type and polarity there is no point in configuring the pin
more than once.
[ tglx: Split out the ce4100 part into a separate patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We call rtc_read_alarm from rtc_device_register, so it is important
that the rtc device is fully initialized prior to registration.
rtc-max8925 sets drvdata after register, so the rtc_read_alarm code
dereferences a NULL pointer.
Call dev_set_drvdata before rtc_device_register.
[ jstultz/tglx: Massaged commit message ]
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Link: http://lkml.kernel.org/r/%3C1303929869-25249-1-git-send-email-john.stultz%40linaro.org%3E
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] slub: fix panic with DISCONTIGMEM
[PARISC] set memory ranges in N_NORMAL_MEMORY when onlined
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
On a remount, the VFS layer will clear the MS_SYNCHRONOUS bit on the
assumption that the flags on the mount syscall will have it set if the
remounted fs is supposed to keep it.
In the case of "noac" though, MS_SYNCHRONOUS is implied. A remount of
such a mount will lose the MS_SYNCHRONOUS flag since "sync" isn't part
of the mount options.
Reported-by: Max Matveev <makc@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When compiling, I was getting this warning:
fs/nfs/nfs4xdr.c: In function ‘decode_secinfo’:
fs/nfs/nfs4xdr.c:4839:6: warning: variable ‘status’ set but not used
[-Wunused-but-set-variable]
We were unconditionally returning 0 as long as there wasn't an error
coming out of xdr_inline_decode(). We probably want to check the error
status coming out of decode_op_hdr() and decode_secinfo_gss(), rather
than assuming that everything is OK all the time.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When readdir() returns a directory entry for the root of a mounted
filesystem, Linux follows the old convention of returning the inode
number of the covered directory (despite newer versions of POSIX declaring
that this is a bug).
To ensure this continues to work, the NFSv4 readdir implementation requests
the 'mounted-on-fileid' from the server.
However, readdirplus also needs to instantiate an inode for this entry, and
for that, we also need to request the real fileid as per this patch.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
It was noticed that P4 machines were generating double NMIs for
each perf event. These extra NMIs lead to 'Dazed and confused'
messages on the screen.
I tracked this down to a P4 quirk that said the overflow bit had
to be cleared before re-enabling the apic LVT mask. My first
attempt was to move the un-masking inside the perf nmi handler
from before the chipset NMI handler to after.
This broke Nehalem boxes that seem to like the unmasking before
the counters themselves are re-enabled.
In order to keep this change simple for 2.6.39, I decided to
just simply move the apic LVT un-masking to the beginning of all
the chipset NMI handlers, with the exception of Pentium4's to
fix the double NMI issue.
Later on we can move the un-masking to later in the handlers to
save a number of 'extra' NMIs on those particular chipsets.
I tested this change on a P4 machine, an AMD machine, a Nehalem
box, and a core2quad box. 'perf top' worked correctly along
with various other small 'perf record' runs. Anything high
stress breaks all the machines but that is a different problem.
Thanks to various people for testing different versions of this
patch.
Reported-and-tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303900353-10242-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Cyrill Gorcunov <gorcunov@gmail.com>
For m68k, N_NORMAL_MEMORY represents all nodes that have present memory
since it does not support HIGHMEM. This patch sets the bit at the time
node_present_pages has been set by free_area_init_node.
At the time the node is brought online, the node state would have to be
done unconditionally since information about present memory has not yet
been recorded.
If N_NORMAL_MEMORY is not accurate, slub may encounter errors since it
uses this nodemask to setup per-cache kmem_cache_node data structures.
This pach is an alternative to the one proposed by David Rientjes
<rientjes@google.com> attempting to set node state immediately when
bringing the node online.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Tested-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: stable@kernel.org
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Multi-gpu/switcheroo relies on this option to get the console on the
correct GPU at bootup, some distros enable it but it seems some get
it wrong.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The EXPERT menu list was recently broken by the insertion of a
kconfig symbol (EMBEDDED) at the beginning of the EXPERT list of
kconfig items. Broken by:
commit 6a108a14fa
Author: David Rientjes <rientjes@google.com>
Date: Thu Jan 20 14:44:16 2011 -0800
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
Restore the EXPERT menu list -- don't inject a symbol (EMBEDDED)
that does not depend on EXPERT into the list.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
