These includes are not actually needed, and asm/rheap.h and
sysdev/fsl_soc.h are PPC-specific, hence prevent compiling QE for
other architectures.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Commit e5c5c8d23f (soc/fsl/qe: only apply QE_General4 workaround on
affected SoCs) introduced use of pvr_version_is(), saying
The QE_General4 workaround is only valid for the MPC832x and MPC836x
SoCs. The other SoCs that embed a QUICC engine are not affected by this
hardware bug and thus can use the computed divisors (this was
successfully tested on the T1040).
I'm reading the above as saying that the errata does not apply to the
ARM-based SOCs with QUICC engine. In any case, use of pvr_version_is()
must be guarded by CONFIG_PPC32 before we can remove the PPC32
dependency from CONFIG_QUICC_ENGINE, so introduce qe_general4_errata()
to keep the necessary #ifdeffery localized to a trivial helper.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
In preparation for allowing QE to be built for architectures other
than ppc, use the generic readx_poll_timeout_atomic() helper from
iopoll.h rather than the ppc-only spin_event_timeout().
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Make it clear that these operate on big-endian registers (i.e. use the
iowrite*be primitives) before we introduce more uses of them and allow
the QE drivers to be built for platforms other than ppc32.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The actual io accessors (e.g. in_be32) implicitly add a volatile
qualifier to their address argument. Remove volatile from the struct
definition and the qe_ic_(read/write) helpers, in preparation for
switching from the ppc-specific io accessors to generic ones.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
This is useful information to have when looking through system logs,
so add it to the output.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A set of fixes that we've merged late, but for the most part that have
been sitting in -next for a while through platform maintainer trees.
+ Fixes to suspend/resume on Tegra, caused by the added features
this merge window
+ Cleanups and minor fixes to TI additions this merge window
+ Tee fixes queued up late before the merge window, included here.
+ A handful of other fixlets
There's also a refresh of the shareed config files (multi_v* on 32-bit,
and defconfig on 64-bit), to avoid conflicts when we get new
contributions.
-----BEGIN PGP SIGNATURE-----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=ozla
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that we've merged late, but for the most part that have
been sitting in -next for a while through platform maintainer trees:
- Fixes to suspend/resume on Tegra, caused by the added features this
merge window
- Cleanups and minor fixes to TI additions this merge window
- Tee fixes queued up late before the merge window, included here.
- A handful of other fixlets
There's also a refresh of the shareed config files (multi_v* on
32-bit, and defconfig on 64-bit), to avoid conflicts when we get new
contributions"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: multi_v7_defconfig: Restore debugfs support
ARM: defconfig: re-run savedefconfig on multi_v* configs
arm64: defconfig: re-run savedefconfig
ARM: pxa: Fix resource properties
soc: mediatek: cmdq: fixup wrong input order of write api
soc: aspeed: Fix snoop_file_poll()'s return type
MAINTAINERS: Switch to Marvell addresses
MAINTAINERS: update Cavium ThunderX drivers
Revert "arm64: dts: juno: add dma-ranges property"
MAINTAINERS: Make Nicolas Saenz Julienne the new bcm2835 maintainer
firmware: arm_scmi: Avoid double free in error flow
arm64: dts: juno: Fix UART frequency
ARM: dts: Fix sgx sysconfig register for omap4
arm: socfpga: execute cold reboot by default
ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangs
ARM: dts: dra7: fix cpsw mdio fck clock
ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3v
ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity
soc/tegra: pmc: Add reset sources and levels on Tegra194
soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
...
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting
-----BEGIN PGP SIGNATURE-----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=3cs2
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"Rob pointed out I missed his pull request for msm-next, it's been in
next for a while outside of my tree so shouldn't cause any unexpected
issues, it has some OCMEM support in drivers/soc that is acked by
other maintainers as it's outside my tree.
Otherwise it's a usual fixes pull, i915, amdgpu, the main ones, with
some tegra, omap, mgag200 and one core fix.
Summary:
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting"
* tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm: (100 commits)
drm/dp_mst: Correct the bug in drm_dp_update_payload_part1()
drm/omap: fix dma_addr refcounting
drm/tegra: Run hub cleanup on ->remove()
drm/tegra: sor: Make the +5V HDMI supply optional
drm/tegra: Silence expected errors on IOMMU attach
drm/tegra: vic: Export module device table
drm/tegra: sor: Implement system suspend/resume
drm/tegra: Use proper IOVA address for cursor image
drm/tegra: gem: Remove premature import restrictions
drm/tegra: gem: Properly pin imported buffers
drm/tegra: hub: Remove bogus connection mutex check
ia64: agp: Replace empty define with do while
agp: Add bridge parameter documentation
agp: remove unused variable num_segments
agp: move AGPGART_MINOR to include/linux/miscdevice.h
agp: remove unused variable size in agp_generic_create_gatt_table
drm/dp_mst: Fix build on systems with STACKTRACE_SUPPORT=n
drm/radeon: fix r1xx/r2xx register checker for POT textures
drm/amdgpu: fix GFX10 missing CSIB set(v3)
drm/amdgpu: should stop GFX ring in hw_fini
...
Fixes a regression for wake events on Tegra194 caused by the Tegra210
support that was added in v5.5-rc1 as well as wrong reset sources and
levels on Tegra194.
-----BEGIN PGP SIGNATURE-----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=Klyx
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
soc/tegra: Fixes for v5.5-rc1
Fixes a regression for wake events on Tegra194 caused by the Tegra210
support that was added in v5.5-rc1 as well as wrong reset sources and
levels on Tegra194.
* tag 'tegra-for-5.5-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add reset sources and levels on Tegra194
soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
soc/tegra: pmc: Use lower-case for hexadecimal literals
Link: https://lore.kernel.org/r/20191204130753.3614278-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This brings in the mainline tree right after armsoc contents was merged
this release cycle, so that we can re-run savedefconfig, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Most of these are for MMP (seeing a bunch of cleanups and refactorings
for the first time in a while), and for OMAP (a bunch of cleanups and
added support for voltage controller on OMAP4430).
-----BEGIN PGP SIGNATURE-----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=Tga8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are for MMP (seeing a bunch of cleanups and refactorings
for the first time in a while), and for OMAP (a bunch of cleanups and
added support for voltage controller on OMAP4430)"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: OMAP2+: Add missing put_device() call in omapdss_init_of()
OMAP2: fixup doc comments in omap_device
ARM: OMAP1: drop duplicated dependency on ARCH_OMAP1
ARM: ASPEED: update default ARCH_NR_GPIO for ARCH_ASPEED
ARM: imx: use generic function to exit coherency
ARM: tegra: Use WFE for power-gating on Tegra30
ARM: tegra: Fix FLOW_CTLR_HALT register clobbering by tegra_resume()
ARM: exynos: Enable exynos-asv driver for ARCH_EXYNOS
ARM: s3c: Rename s5p_usb_phy functions
ARM: s3c: Rename s3c64xx_spi_setname() function
ARM: imx: Add serial number support for i.MX6/7 SoCs
ARM: imx: Drop imx_anatop_usb_chrg_detect_disable()
arm64: Introduce config for S32
ARM: hisi: drop useless depend on ARCH_MULTI_V7
arm64: realtek: Select reset controller
ARM: shmobile: rcar-gen2: Drop legacy DT clock support
ARM: OMAP2+: Remove duplicated include from pmic-cpcap.c
ARM: OMAP1: ams-delta FIQ: Fix a typo ("Initiaize")
MAINTAINERS: Add logicpd-som-lv and logicpd-torpedo to OMAP TREE
ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support
...
Fixup a issue was caused by the previous fixup patch.
Fixes: 1a92f98912 ("soc: mediatek: cmdq: reorder the parameter")
Link: https://lore.kernel.org/r/20191127165428.19662-1-matthias.bgg@gmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
snoop_file_poll() is defined as returning 'unsigned int' but the
.poll method is declared as returning '__poll_t', a bitwise type.
Fix this by using the proper return type and using the EPOLL
constants instead of the POLL ones, as required for __poll_t.
Link: https://lore.kernel.org/r/20191121051851.268726-1-joel@jms.id.au
Fixes: 3772e5da44 ("drivers/misc: Aspeed LPC snoop output using misc chardev")
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
+ OCMEM support to enable the couple generations that had shared OCMEM
rather than GMEM exclusively for the GPU (late a3xx and I think basically
all of a4xx). Bjorn and Brian decided to land this through the drm
tree to avoid having to coordinate merge requests.
+ a510 support, and various associated display support
+ the usual misc cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGv-JWswEJRxe5AmnGQO1SZnpxK05kO1E29K6UUzC9GMMw@mail.gmail.com
Tegra194 supports the same reset levels as Tegra186 but extends the set
of reset sources. Provide custom PMC register definitions to account for
the larger field for the reset sources as well as the updated list of
reset sources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v2:
- use the new Tegra194 register definitions
Reuse the IRQ callbacks from Tegra186 on Tegra194. This fixes failures
to request interrupts on Tegra194 due to the missing callbacks.
Cc: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: aba19827fc ("soc/tegra: pmc: Support wake events on more Tegra SoCs")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The remainder of the file uses lower-case for hexadecimal literals, so
change the only odd-one-out occurrence for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
RCPM driver for ARM SoCs
- add RCPM driver to manage the wakeup devices for QorIQ ARM SoCs (HW low
power states are supported in PSCI firmware)
- add API to PM wakeup framework to retrieve wakeup sources
-----BEGIN PGP SIGNATURE-----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=H6+G
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.5
RCPM driver for ARM SoCs
- add RCPM driver to manage the wakeup devices for QorIQ ARM SoCs (HW low
power states are supported in PSCI firmware)
- add API to PM wakeup framework to retrieve wakeup sources
* tag 'soc-fsl-next-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
PM: wakeup: Add routine to help fetch wakeup source object.
Link: https://lore.kernel.org/r/1573599595-31411-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The NXP's QorIQ processors based on ARM Core have RCPM module
(Run Control and Power Management), which performs system level
tasks associated with power management such as wakeup source control.
Note that this driver will not support PowerPC based QorIQ processors,
and it depends on PM wakeup source framework which provide collect
wake information.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
- a new driver exposing the serial number registers through nvmem
- a few documentation and definition changes
-----BEGIN PGP SIGNATURE-----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=BAax
-----END PGP SIGNATURE-----
Merge tag 'at91-5.5-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/drivers
AT91 drivers for 5.5
- a new driver exposing the serial number registers through nvmem
- a few documentation and definition changes
* tag 'at91-5.5-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
ARM: at91: Documentation: update the sama5d3 and armv7m datasheets
Link: https://lore.kernel.org/r/20191107221644.GA201884@piout.net
Signed-off-by: Olof Johansson <olof@lixom.net>
- Extend firmware interface to cover Versal chip
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXcPhCwAKCRDKSWXLKUoM
IUL7AKCJnOr8MgplpSVBz+SvrOrIrlT2eACgmN3dakmthTjv/mzMngYN42VmxmE=
=eILs
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-for-v5.5' of https://github.com/Xilinx/linux-xlnx into arm/drivers
arm64: soc: Xilinx SoC changes for v5.5
- Extend firmware interface to cover Versal chip
* tag 'zynqmp-soc-for-v5.5' of https://github.com/Xilinx/linux-xlnx:
firmware: xilinx: Add support for versal soc
dt-bindings: firmware: Add bindings for Versal firmware
soc: xilinx: Set CAP_UNUSABLE requirement for versal while powering down domain
Link: https://lore.kernel.org/r/6954a53c-6dab-c7a3-7257-58460ca952cb@monstr.eu
Signed-off-by: Olof Johansson <olof@lixom.net>
Put bus protection enable and disable control in separate functions.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Put sram enable and disable control in separate functions.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
[mb: fix coding style of reading register and changing the read value]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Put clock enable and disable control in separate function.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Put regulator enable and disable control in separate functions.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use USEC_PER_SEC to indicate the polling timeout directly.
And add documentation of scp_domain_data.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
* Add thermal IRQ support on MSM8916, SDM845, MSM8996, and QCS404
* Fix thermal HW ids for cpus on MSM8916
* Add blsp1 UART3 and blsp1 BAM on MSM8998
* Add volume buttons and WCNSS for Wifi and BT on MSM8916 LongCheer-l8150
* Fixup load on l21 for SD on apq8096-db820c
* Enable LVS1/2, APSS watchdog, and select UFS reset gpio for SDM845
* Disable coresight by default on MSM8998
* Enable bluetooth and remove retention idle state on MSM8998-clamshell
* Enable adsp, cdsp, and mpss on C630
* Enable bluetooth on MSM8998-mtp
* Delete zap shader on SDM845-cheza
* Add tactile buttons and hall sensor on MSM8916-Samsung-A2015
* Add Interconnect nodes, watchdog, and sleep clk on QCS404
* Override Iris compatible on MSM8916-Samsung-A5U
* Enable WCNSS Wifi and bluetooth on MSM8916-Samsung-A2015
* Fixup cooling states for the aoss warming devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jkQc
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 Updates for v5.5
* Add thermal IRQ support on MSM8916, SDM845, MSM8996, and QCS404
* Fix thermal HW ids for cpus on MSM8916
* Add blsp1 UART3 and blsp1 BAM on MSM8998
* Add volume buttons and WCNSS for Wifi and BT on MSM8916 LongCheer-l8150
* Fixup load on l21 for SD on apq8096-db820c
* Enable LVS1/2, APSS watchdog, and select UFS reset gpio for SDM845
* Disable coresight by default on MSM8998
* Enable bluetooth and remove retention idle state on MSM8998-clamshell
* Enable adsp, cdsp, and mpss on C630
* Enable bluetooth on MSM8998-mtp
* Delete zap shader on SDM845-cheza
* Add tactile buttons and hall sensor on MSM8916-Samsung-A2015
* Add Interconnect nodes, watchdog, and sleep clk on QCS404
* Override Iris compatible on MSM8916-Samsung-A5U
* Enable WCNSS Wifi and bluetooth on MSM8916-Samsung-A2015
* Fixup cooling states for the aoss warming devices
* tag 'qcom-arm64-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (26 commits)
arm64: dts: qcom: db845c: Enable LVS 1 and 2
arm64: dts: qcom: msm8998: Disable coresight by default
arm64: dts: qcom: msm8998-clamshell: Remove retention idle state
arm64: dts: qcom: sdm845-cheza: delete zap-shader
arm64: dts: msm8916: thermal: Fixup HW ids for cpu sensors
arm64: dts: sdm845: thermal: Add interrupt support
arm64: dts: msm8996: thermal: Add interrupt support
arm64: dts: msm8998: thermal: Add interrupt support
arm64: dts: qcs404: thermal: Add interrupt support
arm64: dts: qcom: sdm845: Add APSS watchdog node
arm64: dts: qcom: c630: Enable adsp, cdsp and mpss
arm64: dts: qcom: msm8998-clamshell: Enable bluetooth
arm64: dts: qcom: msm8998-mtp: Enable bluetooth
arm64: dts: qcom: msm8998: Add blsp1_uart3
arm64: dts: qcom: msm8998: Add blsp1 BAM
arm64: dts: msm8916-longcheer-l8150: Add Volume buttons
arm64: dts: msm8916-longcheer-l8150: Enable WCNSS for WiFi and BT
soc: qcom: Invert the cooling states for the aoss warming devices
arm64: dts: apq8096-db820c: Increase load on l21 for SDCARD
arm64: dts: msm8916-samsung-a2015: add tactile buttons and hall sensor
...
Link: https://lore.kernel.org/r/1573068840-13098-2-git-send-email-agross@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Chip on the board is S905D3 not S905X3:
[ 0.098998] soc soc0: Amlogic Meson SM1 (S905D3) Revision 2b:c (b0:2) Detected
Change from v1: use 0xf0 mask instead of 0xf2 as advised by Neil Armstrong.
Fixes: 1d7c541b8a ("soc: amlogic: meson-gx-socinfo: Add S905X3 ID for VIM3L")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- Skip return check for those SCU firmware APIs that are defined as
void function in firmware.
- Use established serial_number attribute instead of custom one to show
SoC's unique ID for i.MX8 SoC drivers.
- Read i.MX8MQ SOC revision from TF-A which parses ROM and exposes the
value through a SMC call. This improves the situation that SOC
revision reports 'unknown' on some older revisions.
- Add a check and warn on unexpected SCU RX to avoid potential stack
corruption in imx-scu driver.
- Fix a sparse warning in imx-scu-irq driver by adding missing header.
- Remove an unneeded call to devm_of_platform_populate() from imx-dsp
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwVrCAAoJEFBXWFqHsHzOX8kH/3/YHNwwVBHY9t9UqvtYu3y+
1jMCHRX1WdOo9ntRmREzPzAHGFXH/O06AKtWTVp+I5KK3vNy3zJR/wVaIZ3ET3ZY
LK8YD7sc7/PsSHC2Tw4Lj7QnF/q4X5cvo1iL8WeySDyfZQS0UutfPn3VDAwwQGpf
CCcyEou6QfxGipff597COmhaMra8tIaSYZctHFVCOh2mSz2Zny8BRKOgBSKsmPFs
83O/swSyvKlfRisFU2oUcdGX2VgMSuntTCUW9xlYXJtA8cmuUKlSvQK3KjL+KxK7
rjd+oYoBZEvA2RMgsX518lFwI5cnrIP06k93D4KfA15lePbSJ1DKrpuPbL9RHLc=
=9zkv
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.5:
- Skip return check for those SCU firmware APIs that are defined as
void function in firmware.
- Use established serial_number attribute instead of custom one to show
SoC's unique ID for i.MX8 SoC drivers.
- Read i.MX8MQ SOC revision from TF-A which parses ROM and exposes the
value through a SMC call. This improves the situation that SOC
revision reports 'unknown' on some older revisions.
- Add a check and warn on unexpected SCU RX to avoid potential stack
corruption in imx-scu driver.
- Fix a sparse warning in imx-scu-irq driver by adding missing header.
- Remove an unneeded call to devm_of_platform_populate() from imx-dsp
driver.
* tag 'imx-drivers-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx8mq: Read SOC revision from TF-A
soc: imx-scu: Using existing serial_number instead of UID
soc: imx8: Using existing serial_number instead of UID
firmware: imx: add missing include of <linux/firmware/imx/sci.h>
firmware: imx: Remove call to devm_of_platform_populate
firmware: imx: Skip return value check for some special SCU firmware APIs
firmware: imx: warn on unexpected RX
Link: https://lore.kernel.org/r/20191105150315.15477-1-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Minor fixes to Exynos Chipid driver.
2. Add Exynos Adaptive Supply Voltage driver allowing to adjust voltages
used during CPU frequency scaling based on revision of SoC. This
also pulls dependency from PM/OPP tree - driver uses newly added
dev_pm_opp_adjust_voltage() function.
-----BEGIN PGP SIGNATURE-----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=t01z
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung soc drivers changes for v5.5
1. Minor fixes to Exynos Chipid driver.
2. Add Exynos Adaptive Supply Voltage driver allowing to adjust voltages
used during CPU frequency scaling based on revision of SoC. This
also pulls dependency from PM/OPP tree - driver uses newly added
dev_pm_opp_adjust_voltage() function.
* tag 'samsung-drivers-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: exynos-asv: Potential NULL dereference in exynos_asv_update_opps()
soc: samsung: chipid: Drop "syscon" compatible requirement
soc: samsung: Add Exynos Adaptive Supply Voltage driver
PM / OPP: Support adjusting OPP voltages at runtime
soc: samsung: chipid: Make exynos_chipid_early_init() static
Link: https://lore.kernel.org/r/20191104175902.12224-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
SOC revision on older imx8mq is not available in fuses so on anything
other than B1 current code just reports "unknown".
TF-A already handles this by parsing the ROM and exposes the value
through a SMC call. Call this instead of reimplementing the workaround
in the kernel itself.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds wake event support on Tegra210, implements the NVMEM API for the
Tegra FUSE block and adds coupled regulators support for Tegra20 and
Tegra30.
-----BEGIN PGP SIGNATURE-----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=CwCM
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.5-rc1
Adds wake event support on Tegra210, implements the NVMEM API for the
Tegra FUSE block and adds coupled regulators support for Tegra20 and
Tegra30.
* tag 'tegra-for-5.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Remove unnecessary memory barrier
soc/tegra: pmc: Query PCLK clock rate at probe time
soc/tegra: regulators: Add regulators coupler for Tegra30
soc/tegra: regulators: Add regulators coupler for Tegra20
soc/tegra: pmc: Configure deep sleep control settings
soc/tegra: pmc: Configure core power request polarity
soc/tegra: pmc: Add wake event support on Tegra210
soc/tegra: pmc: Support wake events on more Tegra SoCs
soc/tegra: fuse: Register cell lookups for compatibility
soc/tegra: fuse: Add cell information
soc/tegra: fuse: Implement nvmem device
soc/tegra: fuse: Restore base on sysfs failure
soc/tegra: pmc: Fix crashes for hierarchical interrupts
soc/tegra: fuse: Add FUSE clock check in tegra_fuse_readl()
Link: https://lore.kernel.org/r/20191102144521.3863321-4-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'for_5.5/driver-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
memory: emif: remove set but not used variables 'cs1_used' and 'custom_configs'
soc: ti: omap-prm: fix return value check in omap_prm_probe()
soc: ti: omap-prm: add omap5 PRM data
soc: ti: omap-prm: add am4 PRM data
soc: ti: omap-prm: add dra7 PRM data
soc: ti: omap-prm: add data for am33xx
soc: ti: omap-prm: add omap4 PRM data
soc: ti: omap-prm: add support for denying idle for reset clockdomain
soc: ti: omap-prm: poll for reset complete during de-assert
soc: ti: add initial PRM driver with reset control support
dt-bindings: omap: add new binding for PRM instances
Link: https://lore.kernel.org/r/1572372856-20598-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the power areas in the Renesas R-Car M3-W+ (R8A77961)
SoC to the R-Car System Controller driver.
R-Car M3-W+ (aka R-Car M3-W ES3.0) is very similar to R-Car
M3-W (R8A77960), which allows for both SoCs to share a driver:
- R-Car M3-W+ lacks the A2VC power area, so its area must be
nullified,
- The existing support for the SYSCEXTMASK register added in commit
9bd645af9d2a49ac ("soc: renesas: r8a7796-sysc: Fix power request
conflicts") applies to ES3.0 and later only.
As R-Car M3-W+ uses a different compatible value, differentiate
based on that, instead of on the ES version.
Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023123342.13100-7-geert+renesas@glider.be
Add support for the Reset block in the R-Car M3-W+ (R8A77961) SoC to the
Renesas R-Car RST driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023123342.13100-6-geert+renesas@glider.be
Add support for identifying the R-Car M3-W+ (R8A77961) SoC, which shares
the Product ID Number with R-Car M3-W (R8A77960), but differs in CUT
Number (Ver. 3.0), and uses a different compatible value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023123342.13100-5-geert+renesas@glider.be
Add CONFIG_ARCH_R8A77961 as a configuration symbol for the new Renesas
R-Car M3-W+ (R8A77961) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023123342.13100-4-geert+renesas@glider.be
Add CONFIG_ARCH_R8A77960 as a new config symbol for R-Car M3-W
(R8A77960), to replace CONFIG_ARCH_R8A7796, and avoid confusion with
R-Car M3-W+ (R8A77961), which will use CONFIG_ARCH_R8A77961.
Note that for now, CONFIG_ARCH_R8A7796 is retained, and just selects
CONFIG_ARCH_R8A77960. This relaxes dependencies of other subsystems on
the SoC configuration symbol, and provides a smooth transition path for
config files through "make oldconfig".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023123342.13100-3-geert+renesas@glider.be
Rename CONFIG_SYSC_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_SYSC_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_SYSC_R8A77961.
Rename r8a7796_sysc_info and r8a7796_sysc_init for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023123342.13100-2-geert+renesas@glider.be
If the DTB for a device with an RZ/A2 SoC lacks a device node for the
BSID register, the ID validation code falls back to using a register at
address 0x0, which leads to undefined behavior (e.g. reading back a
random value).
This could be fixed by letting fam_rza2.reg point to the actual BSID
register. However, the hardcoded fallbacks were meant for backwards
compatibility with old DTBs only, not for new SoCs. Hence fix this by
validating renesas_family.reg before using it.
Fixes: 175f435f44 ("soc: renesas: identify RZ/A2")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191016143306.28995-1-geert+renesas@glider.be
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the API required to make sure that the devices that use
the QMan portal are unbound when the portal is unbound.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_pm_opp_get_opp_table() returns error pointers if it's disabled
in the config and it returns NULL if there is an error. This code only
checks for error pointers so it could lead to an Oops inside the
dev_pm_opp_put_opp_table() function.
Fixes: 5ea428595c ("soc: samsung: Add Exynos Adaptive Supply Voltage driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 3e99cb214f ("soc: ti: add initial PRM driver with reset control support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The removed barrier isn't needed because writes/reads are strictly ordered
and even if PMC had separate ports for writes, it wouldn't matter since
the hardware logic takes into effect after triggering CPU's power-gating
and at that point all CPU accesses are guaranteed to be completed. That
barrier was copied from the old arch/ code during transition to the soc/
PMC driver and even that the code structure was different back then, the
barrier didn't have a real useful purpose from the start. Lastly, the
tegra_pmc_writel() naturally inserts wmb() because it uses writel(),
and thus this change doesn't actually make any difference in terms of
interacting with hardware. Hence let's remove the barrier to clean up
code a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It is possible to get a lockup if kernel decides to enter LP2 cpuidle
from some clk-notifier, in that case CCF's "prepare" mutex is kept locked
and thus clk_get_rate(pclk) blocks on the same mutex with interrupts being
disabled, hanging machine.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Turned out that WFI doesn't work reliably on Tegra30 as a trigger for
the power-gating, it causes CPU hang under some circumstances like having
memory controller running of PLLP. The TRM doc states that WFI should be
used for the Big-Little "Cluster Switch", while WFE for the power-gating.
Hence let's use the WFE for CPU0 power-gating, like it is done for the
power-gating of a secondary cores. This fixes CPU hang after entering LP2
with memory running off PLLP.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add regulators coupler for Tegra30 SoCs that performs voltage balancing
of a coupled regulators and thus provides voltage scaling functionality.
There are 2 coupled regulators on all Tegra30 SoCs: CORE and CPU. The
coupled regulator voltages shall be in a range of 300mV from each other
and CORE voltage shall be higher than the CPU by N mV, where N depends
on the CPU voltage.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add regulators coupler for Tegra20 SoCs that performs voltage balancing
of a coupled regulators and thus provides voltage scaling functionality.
There are 3 coupled regulators on all Tegra20 SoCs: CORE, RTC and CPU.
The CORE and RTC voltages shall be in range of 170mV from each other and
they both shall be higher than the CPU voltage by at least 120mV. This
sounds like it could be handle by a generic voltage balancer, but the CORE
voltage scaling isn't implemented in any of the upstream drivers yet.
It will take quite some time and effort to hook up voltage scaling for
all of the drivers, hence we will use a custom coupler that will manage
the CPU voltage scaling for the starter.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 and prior Tegra chips have deep sleep entry and wakeup related
timings which are platform specific that should be configured before
entering into deep sleep.
Below are the timing specific configurations for deep sleep entry and
wakeup.
- Core rail power-on stabilization timer
- OSC clock stabilization timer after SOC rail power is stabilized.
- Core power off time is the minimum wake delay to keep the system
in deep sleep state irrespective of any quick wake event.
These values depends on the discharge time of regulators and turn OFF
time of the PMIC to allow the complete system to finish entering into
deep sleep state.
These values vary based on the platform design and are specified
through the device tree.
This patch has implementation to configure these timings which are must
to have for proper deep sleep and wakeup operations.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch configures polarity of the core power request signal
in PMC control register based on the device tree property.
PMC asserts and de-asserts power request signal based on it polarity
when it need to power-up and power-down the core rail during SC7.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements PMC wakeup sequence for Tegra210 and defines the
commonly used RTC alarm wake event.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch allows to create separate irq_set_wake and irq_set_type
implementations for different Tegra designs PMC that has different
wake models which require difference wake registers and different
programming sequence.
AOWAKE model support is available for Tegra186 and Tegra194 only
and it resides within PMC and supports tiered wake architecture.
Tegra210 and prior Tegra designs uses PMC directly to receive wake
events and coordinate the wake sequence.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As we dropped the requirement of "syscon" compatible in the chipid
nodes rework code acquiring the regmap to use device_node_to_regmap()
rather than syscon_node_to_regmap().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Adaptive Supply Voltage (ASV) driver adjusts CPU cluster operating
points depending on exact revision of an SoC retrieved from the CHIPID
block or the OTP memory. This allows for some power saving as for some
CPU clock frequencies we can lower CPU cluster's supply voltage comparing
to safe values common to all the SoC revisions.
This patch adds support for Exynos5422/5800 SoC, it is partially based
on code from https://github.com/hardkernel/linux repository,
branch odroidxu4-4.14.y, files: arch/arm/mach-exynos/exynos5422-asv.[ch].
Tested on Odroid XU3, XU4, XU3 Lite.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The soc_device_attribute structure already contains a serial_number
attribute to show SoC's unique ID, just use it to show SoC's unique
ID instead of creating a new file called soc_uid.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The soc_device_attribute structure already contains a serial_number
attribute to show SoC's unique ID, just use it to show SoC's unique
ID instead of creating a new file called soc_uid.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make the initialiers in imx_gpc_domains C99 format to fix the
following sparse warnings:
drivers/soc/imx/gpc.c:252:30: warning: obsolete array initializer, use C99 syntax
drivers/soc/imx/gpc.c:258:29: warning: obsolete array initializer, use C99 syntax
drivers/soc/imx/gpc.c:269:34: warning: obsolete array initializer, use C99 syntax
drivers/soc/imx/gpc.c:278:30: warning: obsolete array initializer, use C99 syntax
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b0682d485f ("soc: imx: gpc: use GPC_PGC_DOMAIN_* indexes")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Typically nvmem cells would be stored in device tree. However, for
compatibility with device trees that don't contain nvmem cell
definitions, register lookups for cells currently used by consumers.
This allows the consumers to use the same API to query cells from the
device tree or using the legacy mechanism.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The nvmem framework provides a generic infrastructure and API to access
the type of information stored in fuses such as the Tegra FUSE block.
Implement an nvmem device that can be used to access the information in
a more generic way to decouple consumers from the custom Tegra API and
to add a more formal way of creating the dependency between the FUSE
device and the consumers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
For "0" requirement which is used to inform firmware that device is
not required currently by master, Versal PLM (Platform Loader and
Manager) which runs on Platform Management Controller and is responsible
platform management of devices that disables clock, power it down
and reset the device. genpd_power_off() is being called during runtime
suspend also. So, if any device goes to runtime suspend state during
resumes it needs to be re-initialized again. It is possible that
drivers do not reinitialize device upon resume from runtime suspend
every time ans so dont want it to be powered down or get reset
during runtime suspend.
In Versal PLM new PM_CAP_UNUSABLE capability is added, which disables
clock only and avoids power down and reset during runtime suspend. Power
and reset will be gated with core suspend.So, this patch sets
CAPABILITY_UNUSABLE requirement during gpd_power_off()
if platform is other than zynqmp.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Thermal framework takes 0 as the lowest/default state for a
cooling/warming device. The current code has the order inverted with 1
corresponding to lowest state in hardware and 0 the highest state.
Invert this for a better fit with the thermal framework.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is now a global variable that we're modifying to fix the name.
That isn't terribly thread safe and it's not necessary to be a global so
let's just move this to a local variable instead. This saves space in
the symtab and actually reduces kernel image size because the regmap
config is large and we can replace the initialization of that structure
with a memset and a few member assignments.
Cc: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We'll end up with debugfs collisions if we don't give names to the
regmaps created by this driver. Change the name of the config before
registering it so we don't collide in debugfs.
Fixes: 7f9c136216 ("soc: qcom: Add broadcast base for Last Level Cache Controller (LLCC)")
Cc: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add PRM instance data for omap5 family of SoCs. Initially this is just
used to provide reset support.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add PRM instance data for am4 family of SoCs. Initially this is just
used to provide reset support.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add PRM instance data for dra7 family of SoCs. Initially this is just
used to provide reset support.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add PRM instance data for AM33xx SoC. Includes some basic register
definitions and reset data for now.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add PRM data for omap4 family of SoCs. Initially this is just used to
provide reset support.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
TI SoCs hardware reset signals require the parent clockdomain to be
in force wakeup mode while de-asserting the reset, otherwise it may
never complete. To support this, add pdata hooks to control the
clockdomain directly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Poll for reset completion status during de-assertion of reset, otherwise
the IP in question might be accessed before it has left reset properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add initial PRM (Power and Reset Management) driver for TI OMAP class
SoCs. Initially this driver only supports reset control, but can be
extended to support rest of the functionality, like powerdomain
control, PRCM irq support etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
commit 99356b03b4 ("soc: qcom: Make llcc-qcom a generic driver") move
these out of llcc-qcom.h, make the building fails:
drivers/edac/qcom_edac.c:86:40: error: array type has incomplete element type struct llcc_edac_reg_data
static const struct llcc_edac_reg_data edac_reg_data[] = {
^~~~~~~~~~~~~
drivers/edac/qcom_edac.c:87:3: error: array index in non-array initializer
[LLCC_DRAM_CE] = {
^~~~~~~~~~~~
drivers/edac/qcom_edac.c:87:3: note: (near initialization for edac_reg_data)
drivers/edac/qcom_edac.c:88:3: error: field name not in record or union initializer
.name = "DRAM Single-bit",
...
drivers/edac/qcom_edac.c:169:51: warning: struct llcc_drv_data declared inside parameter
list will not be visible outside of this definition or declaration
qcom_llcc_clear_error_status(int err_type, struct llcc_drv_data *drv)
^~~~~~~~~~~~~
This patch move the needed definitions back to include.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 99356b03b4 ("soc: qcom: Make llcc-qcom a generic driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
VIM3L appears to use a different ID:
[ 0.086470] soc soc0: Amlogic Meson SM1 (S905X3) Revision 2b:c (b0:2) Detected
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SoC IDs for the A113L Amlogic A1 SoC.
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The OCMEM driver handles allocation and configuration of the On Chip
MEMory that is present on some Snapdragon SoCs. Devices which have
OCMEM do not have GMEM inside the GPU core, so the GPU must instead
use OCMEM to be functional. Since the GPU is currently the only OCMEM
user with an upstream driver, this is just a minimal implementation
sufficient for statically allocating to the GPU it's chunk of OCMEM.
This driver currently does not read the gmu-sram node that is described
in the device tree bindings. The starting memory address of the GPU's
reserved memory region is hardcoded to zero to match what the hardware
expects. The driver can be updated to read the reserved memory regions
from device tree once other users of OCMEM are added upstream.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Co-developed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Gabriel Francisco <frc.gabrielgmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The MSM8956/76 SoCs have two main voltage-level power domains, VDD_CX
and VDD_MX, which also have their own voltage-floor-level (VFL)
corner.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SCU firmware API for getting UID should have response,
otherwise, the message stored in function stack could be
released and then the response data received from SCU will be
stored into that released stack and cause kernel NULL pointer
dump.
Fixes: 73feb4d0f8 ("soc: imx-scu: Add SoC UID(unique identifier) support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a compatible for the RPM on the Qualcomm MSM8976 platform:
this is also valid for MSM8956 and their APQ variants.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Register a platform device to handle the communication of bus bandwidth
requests with the remote processor. The interconnect proxy device is part
of this remote processor (RPM) hardware. Let's create a icc-smd-rpm proxy
child device to represent the bus throughput functionality that is provided
by the RPM.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This makes way for adding future llcc versions.
Also pull out the llcc-qcom specific definitions from includes.
Includes path now contains the only definitions that are
to be exposed to other subsystems.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The cleaning up was done without changing the driver file name
to ensure a cleaner bisect. Change the file name now to facilitate
making the driver generic in subsequent patch.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A single file should suffice the need to program the llcc for
various platforms. Get rid of sdm845 specific driver file to
make way for a more generic driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Interrupts that don't have an associated wake event or GPIO wake events
end up with an associate IRQ chip that is NULL and which causes IRQ code
to crash. This is because we don't implicitly set the parent IRQ chip by
allocating the interrupt at the parent. However, there really isn't a
corresponding interrupt at the parent, so we need to work around this by
setting the special no_irq_chip as the IRQ chip for these interrupts.
Fixes: 19906e6b16 ("soc/tegra: pmc: Add wake event support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
tegra_fuse_readl() can be called from drivers at any time. If this API
is called before tegra_fuse_probe(), we end up enabling the clock before
it is registered. Add a check for the FUSE clock in tegra_fuse_readl()
and propagate any errors.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
No R-Car or RZ/G SYSC driver uses any of the definitions provided by
<linux/bug.h>, hence there is no need to include this header file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190920144705.27394-1-geert+renesas@glider.be
Describe the location and contents of the SYSCEXTMASK register on
RZ/G2E, to prevent conflicts between internal and external power
requests.
Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190920143523.23125-1-geert+renesas@glider.be
Describe the location and contents of the SYSCEXTMASK register on R-Car
E3, to prevent conflicts between internal and external power requests.
Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190828113618.6672-8-geert+renesas@glider.be
Describe the location and contents of the SYSCEXTMASK register on R-Car
V3H, to prevent conflicts between internal and external power requests.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190828113618.6672-7-geert+renesas@glider.be
Describe the location and contents of the SYSCEXTMASK register on R-Car
V3M, to prevent conflicts between internal and external power requests.
Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190828113618.6672-6-geert+renesas@glider.be
Describe the location and contents of the SYSCEXTMASK register on R-Car
M3-N, to prevent conflicts between internal and external power requests.
Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190828113618.6672-5-geert+renesas@glider.be
Describe the location and contents of the SYSCEXTMASK register on R-Car
M3-W, to prevent conflicts between internal and external power requests.
This register does not exist on R-Car M3-W ES1.x.
Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190828113618.6672-4-geert+renesas@glider.be
Describe the location and contents of the SYSCEXTMASK register on R-Car
H3, to prevent conflicts between internal and external power requests.
This register does not exist on R-Car H3 ES1.x and ES2.x.
Based on a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190828113618.6672-3-geert+renesas@glider.be
Recent R-Car Gen3 SoCs added an External Request Mask Register to the
System Controller (SYSC). This register allows to mask external power
requests for CPU or 3DG domains, to prevent conflicts between powering
off CPU cores or the 3D Graphics Engine, and changing the state of
another power domain through SYSC, which could lead to CPG state machine
lock-ups.
Add support for making use of this register. Take into account that the
register is optional, and that its location and contents are
SoC-specific.
Note that the issue fixed by this cannot happen in the upstream kernel,
as upstream has no support for graphics acceleration yet. SoCs lacking
the External Request Mask Register may need a different mitigation in
the future.
Inspired by a patch in the BSP by Dien Pham <dien.pham.ry@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190828113618.6672-2-geert+renesas@glider.be
The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJdf6RZAAoJEJpsee/mABjZDO0QAKGkhoEdUmrar0Yf7/ibTrLK
0naWvQtPEm6dv+u1zNfe2IWchVRbBVm+YSLbyaAZwJQknV5gdxgd/UyQrSG9yywg
xDEUdnj03AksYreWbr1tfcA6kQQJEeqZeysNej0v7MAd6MFz5O4M4CgYfAnCLCc4
5rzSqbtFgv4uNMnMTJGKk8anFWNYLbewoBGVcGIEQ/KQlf1+NrlqBWk7CgvencaF
VLqpK0mllhKxAOJHGz6Q/XXiJnj0u56X9GvfcJoaxDWVrAnC6ii29NOHKeXhxS5W
/EmhIEuqCRoGLAMYmml+NbCv43Z1L7neDJwg6sf9cVqNrB9L1Ldlgpr/uoj++Z+l
wdZ297Ogs4mKYx5CCdK4X1TaFOH3s+/awFr1uEP70p+QsPDMrCTuLSjgeQziylgO
kBGIGkqG4l48V9psQy/9SaalgGSB8w6Ta/ms1+rWc99Qj3ExDFCAMIl4uzOxjxT1
9MZbvhc3ulLT4BBXNGhvNaPJxYGk+ggV/ObsqF9+GkxLcVPR8L1tPIzZMB5dB1YR
0YcwyK2jlZGKIwMjLYDT+axGGPh9G+LV6INjRbW5BGJHgNZF844Bxw/eFYushLAu
KHrbpm3ImzJw9eHlgIRtFRTy8ZKPuvv7fGg3zzKSHT4ZmC3tEM68PnQGuMEvVX8Q
+Oa6OiDb0pkV1zsACSZn
=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
* Add AOSS QMP support
* Various fixups for Qualcomm SCM
* Add socinfo driver
* Add SoC serial number attribute and associated APIs
* Add SM8150 and SC7180 support in Qualcomm SCM
* Fixup max processor count in SMEM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJdZpm4AAoJEFKiBbHx2RXV6UEP/1S0B3yKF+/HBylghMBgYI21
P0qWH0cGSYioCLYEPn1qZjftBGSg9K3e31IoFk/mSDy0rt4wbg53ribkL6tE7M+c
ZLZfOs06stGLg6Nf/oLz2SbN2bQsIZBGJoVgp58N/z4Qymspvf7Vg4y9VCy/dzqe
R5bQZhYNWJNzv2q2vju06ACCkQgkRVfIuQSI+69t3bbeWJrHatVrPRHP8Xi8kaTh
/nI7hkO9ouMC6Uda8/aeGoo5V/xaC+rankp9ttdFeHNVXMgk6c3v5rD4fSYw+CVY
Icw7MCKGF1QPjHkLofTZsqpADHabUwu/NmDV1D5c1A/qu0gBocPSI1o1XbChlceS
E/3oO9DJQoNxJOKPxMzZwtVRAeGGrk7/PflkBY+/55XNXO4zasD0Kbi3/ReUokBJ
G5zyN/Lm/gsSfsyiJBFMN02mxbKixlSd/XDp/gClLf7f1QXV+IFyeiDkyMxWH00b
gM4c8hJalWJ2jKi9JDA7GVJD9N+8Q76+Z4HmGiyJJZXtLrVB+ehQFrSOxt97qvBE
4KeZUTfSON++8LpWeP3zVSB1Kox6+cCGQEK0VmwhEHOjE4gg8iV/YIKznwx7clTn
XepzT4K49xO5NQ9h9g2rXNdzvuXvVrKA/CuCtv6/24aSifHHpFroCIewcKZa++/m
Pv3LzPbX4a8d5Hq/qP0o
=MsUS
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.4
* Add AOSS QMP support
* Various fixups for Qualcomm SCM
* Add socinfo driver
* Add SoC serial number attribute and associated APIs
* Add SM8150 and SC7180 support in Qualcomm SCM
* Fixup max processor count in SMEM
* tag 'qcom-drivers-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: aoss: Add AOSS QMP support
dt-bindings: soc: qcom: aoss: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: re-order compatible list
soc: qcom: smem: Update max processor count
soc: qcom: socinfo: Annotate switch cases with fall through
soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.
soc: qcom: socinfo: Expose image information
soc: qcom: socinfo: Expose custom attributes
soc: qcom: Add socinfo driver
base: soc: Export soc_device_register/unregister APIs
base: soc: Add serial_number attribute to soc
firmware: qcom_scm: Cleanup code in qcom_scm_assign_mem()
firmware: qcom_scm: Fix some typos in docs and printks
firmware: qcom_scm: Use proper types for dma mappings
When booting with ACPI, the Geni Serial Engine is not set as the I2C/SPI
parent and thus, the wrapper (parent device) is unassigned. This causes
the kernel to crash with a null dereference error.
Link: https://lore.kernel.org/r/20190905082555.15020-1-lee.jones@linaro.org
Fixes: 8bc529b253 ("soc: qcom: geni: Add support for ACPI")
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
TISCI protocol supports for enabling the device either with exclusive
permissions for the requesting host or with sharing across the hosts.
There are certain devices which are exclusive to Linux context and
there are certain devices that are shared across different host contexts.
So add support for getting this information from DT by increasing
the power-domain cells to 2.
For keeping the DT backward compatibility intact, defaulting the
device permissions to set the exclusive flag set. In this case the
power-domain-cells is 1.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from Anson Huang to add UID support for i.MX8 SoC and SCU
drivers.
- A series from Daniel Baluta to add DSP IPC driver for communication
between host AP (Linux) and the firmware running on DSP embedded in
i.MX8 SoCs.
- A small fix for GPCv2 error code printing.
- Switch from module_platform_driver_probe() to module_platform_driver()
for imx-weim driver, as we need the driver to probe again when device
is present later.
- Add optional burst clock mode support for imx-weim driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYoCEAAoJEFBXWFqHsHzOkDgH/jWNgp3QR3omPQGX80oM6/ga
3x78GDJyQfzZKWyOJbWz12tzXWlD1fmGIZy7SeuvXlYUbNnE1WU6ARFGDoBpjbew
DOYoPT9x7eJemSdnEE43g2vtspEzb6Afvb7dr78OPaik24eY0dFx90U0tzptmuVY
gXxkAHo2ez6txXTu5Id9Z5Deitukb8NoK/9yyzTeD0oYn2hCooAp5fAl1rKgfLnf
MpG29TCK8dxr/j7tzsbt2nutJJYy1Ybh/0WpOMXnBwdAz20JT7MU87DMil0//Q02
0Es/P2xH7K4r3ca9mupDtXZps2DbnmYJorvxpfHuMXcyq0uxGhl1/zyhTv+LW4c=
=5mGq
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.4:
- A series from Anson Huang to add UID support for i.MX8 SoC and SCU
drivers.
- A series from Daniel Baluta to add DSP IPC driver for communication
between host AP (Linux) and the firmware running on DSP embedded in
i.MX8 SoCs.
- A small fix for GPCv2 error code printing.
- Switch from module_platform_driver_probe() to module_platform_driver()
for imx-weim driver, as we need the driver to probe again when device
is present later.
- Add optional burst clock mode support for imx-weim driver.
* tag 'imx-drivers-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: gpcv2: Print the correct error code
bus: imx-weim: use module_platform_driver()
firmware: imx: Add DSP IPC protocol interface
soc: imx-scu: Add SoC UID(unique identifier) support
bus: imx-weim: optionally enable burst clock mode
firmware: imx: scu-pd: Add IRQSTR_DSP PD range
firmware: imx: scu-pd: Add mu13 b side PD range
firmware: imx: scu-pd: Rename mu PD range to mu_a
soc: imx8: Add i.MX8MM UID(unique identifier) support
soc: imx8: Add i.MX8MQ UID(unique identifier) support
Link: https://lore.kernel.org/r/20190825153237.28829-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
reoder function parameter and change size of the parameters
-----BEGIN PGP SIGNATURE-----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=WH2P
-----END PGP SIGNATURE-----
Merge tag 'v5.3-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
cmdq helper:
reoder function parameter and change size of the parameters
* tag 'v5.3-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: cmdq: change the type of input parameter
soc: mediatek: cmdq: reorder the parameter
Link: https://lore.kernel.org/r/8c860e37-3816-d75f-fc37-ce496905ba73@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights
- clk-measure: support new S905X3 and A311D SoCs
- socinfo: support new S905X3 and A311D SoCs
-----BEGIN PGP SIGNATURE-----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=txyO
-----END PGP SIGNATURE-----
Merge tag 'amlogic-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/drivers
soc: amlogic: driver updates for v5.4
Highlights
- clk-measure: support new S905X3 and A311D SoCs
- socinfo: support new S905X3 and A311D SoCs
* tag 'amlogic-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
soc: amlogic: meson-gx-socinfo: Add of_node_put() before return
soc: amlogic: clk-measure: Add support for SM1
dt-bindings: soc: amlogic: clk-measure: Add SM1 compatible
soc: amlogic: meson-gx-socinfo: Add SM1 and S905X3 IDs
soc: amlogic: meson-gx-socinfo: add A311D id
soc: amlogic: meson-clk-measure: add G12B second cluster cpu clk
soc: amlogic: meson-clk-measure: protect measure with a mutex
Link: https://lore.kernel.org/r/7h7e77cwv5.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add Exynos Chipid driver for identification of product IDs and SoC
revisions. The driver also exposes chipid regmap, later to be used by
Exynos Adaptive Supply Voltage driver (adjusting voltages to different
revisions of same SoC).
-----BEGIN PGP SIGNATURE-----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=7pIf
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung soc drivers changes for v5.4
Add Exynos Chipid driver for identification of product IDs and SoC
revisions. The driver also exposes chipid regmap, later to be used by
Exynos Adaptive Supply Voltage driver (adjusting voltages to different
revisions of same SoC).
* tag 'samsung-drivers-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: chipid: Convert exynos-chipid driver to use the regmap API
soc: samsung: Add exynos chipid driver support
Link: https://lore.kernel.org/r/20190816163042.6604-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The move of the IXP4xx SoC drivers exposed their config options on all
platforms.
Fix this by wrapping them inside an ARCH_IXP4XX or COMPILE_TEST block.
Link: https://lore.kernel.org/r/20190823090352.12243-1-linus.walleij@linaro.org
Fixes: fcf2d8978c ("ARM: ixp4xx: Move NPE and QMGR to drivers/soc")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the General Purpose Amlogic Everything-Else Power controller,
with the first support for G12A and SM1 SoCs dedicated to the VPU, PCIe,
USB, NNA, GE2D and Ethernet Power Domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The current code prints 'ret' (thus 0) while it should use 'err'.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the cmdq hardware design, the subsys is u8,
the offset is u16 and the event id is u16.
This patch changes the type of subsys, offset and event id
to the correct type.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The order of gce instructions is [subsys offset value]
so reorder the parameter of cmdq_pkt_write_mask
and cmdq_pkt_write function.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
ARM Erratum 754322 affects Cortex-A9 revisions r2p* and r3p*.
Automatically enable support code to mitigate the erratum when compiling
a kernel for any of the affected Renesas SoCs:
- RZ/A1: r3p0,
- R-Mobile A1: r2p4,
- R-Car M1A: r2p2-00rel0,
- R-Car H1: r3p0,
- SH-Mobile AG5: r2p2.
EMMA Mobile EV2 (r1p3) and RZ/A2 (r4p1) are not affected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
ARM Erratum 814220 affects Cortex-A7 revisions r0p2-r0p5.
Automatically enable support code to mitigate the erratum when compiling
a kernel for any of the affected Renesas SoCs:
- R-Mobile APE6: r0p2,
- RZ/G1E: r0p5,
- RZ/G1C: r0p5,
- R-Car H2: r0p3,
- R-Car E2: r0p5,
- RZ/N1: r0p5.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Currently the R-Mobile "always-on" PM Domain is implemented by returning
-EBUSY from the generic_pm_domain.power_off() callback, and doing
nothing in the generic_pm_domain.power_on() callback. However, this
means the PM Domain core code is not aware of the semantics of this
special domain, leading to boot warnings like the following on
SH/R-Mobile SoCs:
sh_cmt e6130000.timer: PM domain c5 will not be powered off
Fix this by making the always-on nature of the domain explicit instead,
by setting the GENPD_FLAG_ALWAYS_ON flag. This removes the need for the
domain to provide power control callbacks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The chipid driver uses the MFD syscon API but it was not covered
properly in Kconfig.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In commit 40d8aff614 ("soc: samsung: chipid: Convert exynos-chipid
driver to use the regmap API") of_find_compatible_node() call was
substituted with syscon_regmap_lookup_by_compatible() but also an error
log was added for case where lookup fails. On multiplatform the lookup
will always fail on any non-samsung device so the log is incorrect.
Remove the error log and just return an error code from
syscon_regmap_lookup_by_compatible() which internally calls
of_find_compatible_node().
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Update max processor count to reflect the number of
co-processors on SC7180 SoCs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The variable np in function meson_gx_socinfo_init takes the return value
of of_find_compatible_node, which gets a node but does not put it. If
this node is not put it may cause a memory leak. Hence put np after its
usefulness has been exhausted.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: a9daaba296 ("soc: Add Amlogic SoC Information driver")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the clk-measurer clocks IDs for the Amlogic SM1 SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SoC IDs for the S905X3 Amlogic SM1 SoC.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently when the call to product_id_to_soc_id fails there
is a memory leak of soc_dev_attr->revision and soc_dev_attr
on the error return path. Fix this by adding a common error
return path that frees there obects and use this for two
error return paths.
Addresses-Coverity: ("Resource leak")
Fixes: 3253b7b7cd ("soc: samsung: Add exynos chipid driver support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As of commit 980532a5dd ("soc: renesas: rcar-sysc: Use
GENPD_FLAG_ALWAYS_ON"), the local variable "gov" is assigned just once,
so it can be eliminated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The local variable np in function rcar_sysc_pd_init takes the return
value of of_find_matching_node_and_match(), which gets a node but does
not put it. If np is not put before the function returns, it may cause
a memory leak.
Hence, remove the return statement that does not immediately follow a
putting of np. Replace it with a goto pointing to a pre-existing label
that first puts np and then returns the required value.
Issue found with Coccinelle.
Fixes: afa6f53df6 ("soc: renesas: rcar-sysc: Add support for fixing up power area tables")
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Starting with commit 72175d4ea4 ("driver core: Make driver core
own stateful device links") stateful device links are owned by the
driver core and should not be explicitly removed on device unbind.
Delete all device_link_remove appearances from the dpio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Adding compatible string "ls1028a-dcfg" to initialize guts driver
for ls1028 and SoC die attribute definition for LS1028A
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When using the reserved memory node in the device tree there are
two options - dynamic or static. If a dynamic allocation was
selected (where the kernel selects the address for the allocation)
convert it to a static allocation by inserting the reg property.
This will ensure the same memory is reused after a kexec()
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When shutting down a FQ on a dedicated channel only the
SW portal associated with that channel can dequeue from it.
Make sure the correct portal is use.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The drain_mr_fqni() function may be called fron uninterruptable
context so convert the msleep() to an mdelay(). Also ensure that
the valid bit is updated while polling.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
If the QMan device was previously initialized make sure all the
frame queues are out of service once all the portals are probed.
This handles the case where the kernel is restarted without the
SoC being reset (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Clean the BMan buffer pools if the device had been initialized
previously. This will ensure a consistent state if the kernel
was soft restarted (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Rework QBMan private memory setup so that the areas are not
zeroed if the device was previously initialized
If the QMan private memory was already initialized skip the PFDR
initialization.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thierry Reding <treding@nvidia.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Convert the driver to use regmap API in order to allow other
drivers, like ASV, to access the CHIPID registers.
Add definition of selected CHIPID register offsets and register bit
fields for Exynos5422 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos SoCs have Chipid, for identification of product IDs and SoC
revisions. This patch intends to provide initialization code for all
these functionalities, at the same time it provides some sysfs entries
for accessing these information to user-space.
This driver uses existing binding for exynos-chipid.
Changes by Bartlomiej:
- fixed return values on errors
- removed bogus kfree_const()
- added missing Exynos4210 EVT0 id
- converted code to use EXYNOS_MASK define
- fixed np use after of_node_put()
- fixed too early use of dev_info()
- made driver fail for unknown SoC-s
- added SPDX tag
- updated Copyrights
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
[m.szyprowski: for suggestion and code snippet of product_id_to_soc_id]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[s.nawrocki: updated copyright date, removed uneeded headers inclusion]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We have another fix to disable voltage switching for am57xx SDIO as
the bootrom cannot handle all the voltages after a reset that thought
I had already sent a pull request for earlier but forgot. And we also
update dra74x iodelay configuration for mmc3 to use the recommended
values.
Then I noticed we had introduced few new boot warnings with the various
recent ti-sysc changes and wanted to fix those. I also noticed we still
have too many warnings to be able to spot the real ones easily and fixed
up few of those. Sure some of the warnings have been around for a long
time and few of the fixes could have waited for the merge window, but
having more usable dmesg log level output is a valuable.
Other fixes are IO size correction for am335x UARTs that cause issues
for at least FreeBSD using the same device tree file that checks that
the child IO range is not larger than the parent has.
For omap1 ams-delta keyboard we need to fix a irq ack that broke with
all the recent gpio changes.
And there are also few static checker warning fixes for recent am335x
PM changes and ti-sysc driver and one switch fall-though update.
-----BEGIN PGP SIGNATURE-----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=TsdN
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.3/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omap variants for v5.3-rc cycle
We have another fix to disable voltage switching for am57xx SDIO as
the bootrom cannot handle all the voltages after a reset that thought
I had already sent a pull request for earlier but forgot. And we also
update dra74x iodelay configuration for mmc3 to use the recommended
values.
Then I noticed we had introduced few new boot warnings with the various
recent ti-sysc changes and wanted to fix those. I also noticed we still
have too many warnings to be able to spot the real ones easily and fixed
up few of those. Sure some of the warnings have been around for a long
time and few of the fixes could have waited for the merge window, but
having more usable dmesg log level output is a valuable.
Other fixes are IO size correction for am335x UARTs that cause issues
for at least FreeBSD using the same device tree file that checks that
the child IO range is not larger than the parent has.
For omap1 ams-delta keyboard we need to fix a irq ack that broke with
all the recent gpio changes.
And there are also few static checker warning fixes for recent am335x
PM changes and ti-sysc driver and one switch fall-though update.
* tag 'omap-for-v5.3/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: pm33xx: Make two symbols static
soc: ti: pm33xx: Fix static checker warnings
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: dts: Fix incomplete dts data for am3 and am4 mmc
bus: ti-sysc: Simplify cleanup upon failures in sysc_probe()
ARM: OMAP1: ams-delta-fiq: Fix missing irq_ack
ARM: dts: dra74x: Fix iodelay configuration for mmc3
ARM: dts: am335x: Fix UARTs length
ARM: OMAP2+: Fix omap4 errata warning on other SoCs
ARM: dts: Fix incorrect dcan register mapping for am3, am4 and dra7
ARM: dts: Fix flags for gpio7
bus: ti-sysc: Fix using configured sysc mask value
bus: ti-sysc: Fix handling of forced idle
ARM: OMAP2+: Fix missing SYSC_HAS_RESET_STATUS for dra7 epwmss
ARM: dts: am57xx: Disable voltage switching for SD card
Link: https://lore.kernel.org/r/pull-1565844391-332885@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a slew of Ux500 updates for the v5.4 kernel cycle:
- Stop populating the PRCMU devices from the core CPU
file, it works just fine at device_initcall() level.
- Add a missing of_node_put() in the core file.
- Simplify the debug UART code.
- Add myself to MAINTAINERS
* tag 'ux500-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
MAINTAINERS: add soc/ux500
ARM: ux500: simplify and move debug UART
ARM: ux500: add missing of_node_put()
ARM: ux500: Stop populating the PRCMU devices early
Link: https://lore.kernel.org/r/CACRpkdbH-h5fRwuidcpeOp8mtRoKUW65SAk8a4A==BCDzn3QMA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix a flexible array member definition in the R-Car SYSC driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXUQczwAKCRCKwlD9ZEnx
cKN7AQCqies8aPvDBHhx4TmGi3rAutEcYtvJGpYfEqON2neKIwD8C3/iPd+NUQdH
Q4ulQIhTFkrIXyobb5BrMD3QENygtgA=
=LULc
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/drivers
Renesas driver updates for v5.4
- Fix a flexible array member definition in the R-Car SYSC driver.
* tag 'renesas-drivers-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: rcar-sysc: Use [] to denote a flexible array member
Link: https://lore.kernel.org/r/20190802120355.1430-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix sparse warnings:
drivers/soc/ti/pm33xx.c:144:27: warning: symbol 'rtc_wake_src' was not declared. Should it be static?
drivers/soc/ti/pm33xx.c:160:5: warning: symbol 'am33xx_rtc_only_idle' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch fixes a bunch of static checker warnings.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce fall through annotations in the switch statements of
socinfo_debugfs_init() to silence compiler warnings.
Acked-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Fixes: 9c84c1e786 ("soc: qcom: socinfo: Expose custom attributes")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The AOSS QMP driver is extended to communicate with the additional
resources. These resources are then registered as cooling devices
with the thermal framework.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The socinfo driver provides information about version of the various
images loaded in the system. Expose this to user space for debugging
purpose.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Qualcomm socinfo provides a number of additional attributes,
add these to the socinfo driver and expose them via debugfs
functionality.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Qualcomm socinfo driver exposes information about the SoC, its
version and its serial number to user space.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Imran Khan <kimran@codeaurora.org>
[Bjorn: Extract code to platform_driver, split patch in multiple]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[Vaishali: Simplify declarations, introduce qcom_socinfo struct, Fix
memory leak, Remove extra code and Misc code refactoring]
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the SoC ID for the A311D Amlogic SoC.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the G12B second CPU cluster CPU and SYS_PLL measure IDs.
These IDs returns 0Hz on G12A.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In order to protect clock measuring when multiple process asks for
a measure, protect the main measure function with mutexes.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Flexible array members should be denoted using [] instead of [0], else
gcc will not warn when they are no longer at the end of the structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
of_find_compatible_node() returns a pointer with refcount incremented
so both in the error path as well as after usage in soc_info_populate()
respectively actually b8500_read_soc_id() an explicit of_node_put is
needed to release backupram.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit 18a9927878 ("ARM: ux500: move soc_id driver to drivers/soc")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
QUICC Engine
- Add support for importing qe-snums through device tree
- Some cleanups and foot print optimzation
-----BEGIN PGP SIGNATURE-----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=zaF/
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.3 (take 2)
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
QUICC Engine
- Add support for importing qe-snums through device tree
- Some cleanups and foot print optimzation
* tag 'soc-fsl-next-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: fold qe_get_num_of_snums into qe_snums_init
soc: fsl: qe: support fsl,qe-snums property
dt-bindings: soc: fsl: qe: document new fsl,qe-snums binding
soc: fsl: qe: introduce qe_get_device_node helper
soc: fsl: qe: reduce static memory footprint by 1.7K
soc: fsl: qe: drop useless static qualifier
soc: fsl: fix spelling mistake "Firmaware" -> "Firmware"
Link: https://lore.kernel.org/r/20190605194511.12127-1-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM Mali
GPU devices added to device trees, since the DRM drivers have now been
merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Polish and fixes for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now at
feature parity with TX1
-----BEGIN PGP SIGNATURE-----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=sHZs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Devicetree updates from Olof Johansson:
"We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM
Mali GPU devices added to device trees, since the DRM drivers have now
been merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Fixes and polish for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now
at feature parity with TX1"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (586 commits)
ARM: dts: gemini: Set DIR-685 SPI CS as active low
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family
ARM: dts: exynos: Move Mali400 GPU node to "/soc"
ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210
arm64: dts: qcom: qcs404: Add missing space for cooling-cells property
arm64: dts: rockchip: Fix USB3 Type-C on rk3399-sapphire
arm64: dts: rockchip: Update DWC3 modules on RK3399 SoCs
arm64: dts: rockchip: enable rk3328 watchdog clock
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
arm64: dts: rockchip: Add support for Hugsun X99 TV Box
arm64: dts: rockchip: Define values for the IPA governor for rock960
arm64: dts: rockchip: Fix multiple thermal zones conflict in rk3399.dtsi
arm64: dts: rockchip: add core dtsi file for RK3399Pro SoCs
arm64: dts: rockchip: improve rk3328-roc-cc rgmii performance.
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
arm64: dts: qcom: sdm845-cheza: add initial cheza dt
ARM: dts: msm8974-FP2: Add vibration motor
...
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus Walleij--
the SoC doesn't have active maintainers with hardware, and in
discussions with the vendor the agreement was that it's OK to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support.
-----BEGIN PGP SIGNATURE-----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=FX6e
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
This adds support for the STM32 remoteproc, additional i.MX platforms
with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP. Initial
support for vendor specific resource table entries and support for
unprocessed Qualcomm firmware files.
-----BEGIN PGP SIGNATURE-----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=iqXq
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.3' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for the STM32 remoteproc, additional i.MX platforms
with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP.
Also initial support for vendor specific resource table entries and
support for unprocessed Qualcomm firmware files"
* tag 'rproc-v5.3' of git://github.com/andersson/remoteproc:
remoteproc: stm32: fix building without ARM SMCC
remoteproc: qcom: q6v5-mss: Fix build error without QCOM_MDT_LOADER
remoteproc: copy parent dma_pfn_offset for vdev
remoteproc: qcom: q6v5-mss: Support loading non-split images
soc: qcom: mdt_loader: Support loading non-split images
remoteproc: stm32: add an ST stm32_rproc driver
dt-bindings: remoteproc: add bindings for stm32 remote processor driver
dt-bindings: stm32: add bindings for ML-AHB interconnect
remoteproc: Use struct_size() helper
remoteproc: add vendor resources handling
remoteproc: imx: Fix typo in "failed"
remoteproc: imx: Broaden the Kconfig selection logic
remoteproc,rpmsg: add missing MAINTAINERS file entries
remoteproc: qcom: qdsp6-adsp: Add support for QCS404 CDSP
dt-bindings: remoteproc: Rename and amend Hexagon v56 binding
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
Convert docs to ReST and add them to the arch-specific
book.
The conversion here was trivial, as almost every file there
was already using an elegant format close to ReST standard.
The changes were mostly to mark literal blocks and add a few
missing section title identifiers.
One note with regards to "--": on Sphinx, this can't be used
to identify a list, as it will format it badly. This can be
used, however, to identify a long hyphen - and "---" is an
even longer one.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while with
no reported issues. Nothing is earth-shattering, just constant forward
progress for more devices supported and cleanups and small fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed in.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXjYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynMYACgnSRP3GylwMywrkc9paVmDeiIgNwAn0N2sika
JEW7C3lkBJZJ7R6V/Ynm
=drla
-----END PGP SIGNATURE-----
Merge tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
- Improve the handling of shared ACPI power resources in the PCI
bus type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec
into account as appropriate and avoid polling devices in D3cold
for PME (Mika Westerberg).
- Fix some corner case issues in ACPI device power management and
in the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210,
and armada-37xx cpufreq drivers (David Arcari, Florian Fainelli,
Paweł Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black).
-----BEGIN PGP SIGNATURE-----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=aBN3
-----END PGP SIGNATURE-----
Merge tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update PCI and ACPI power management (improved handling of ACPI
power resources and PCIe link delays, fixes related to corner cases,
hibernation handling rework), fix and extend the operating performance
points (OPP) framework, add new cpufreq drivers for Raspberry Pi and
imx8m chips, update some other cpufreq drivers, clean up assorted
pieces of PM code and documentation and update tools.
Specifics:
- Improve the handling of shared ACPI power resources in the PCI bus
type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec into
account as appropriate and avoid polling devices in D3cold for PME
(Mika Westerberg).
- Fix some corner case issues in ACPI device power management and in
the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210, and
armada-37xx cpufreq drivers (David Arcari, Florian Fainelli, Paweł
Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black)"
* tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (57 commits)
ACPI: PM: Make acpi_sleep_state_supported() non-static
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Unexport acpi_device_get_power()
Documentation: ABI: power: Add missing newline at end of file
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
cpufreq: Don't skip frequency validation for has_target() drivers
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
cpufreq: Use has_target() instead of !setpolicy
...
* pm-cpufreq:
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
cpufreq: Don't skip frequency validation for has_target() drivers
cpufreq: Use has_target() instead of !setpolicy
cpufreq: Remove redundant !setpolicy check
cpufreq: Move the IS_ENABLED(CPU_THERMAL) macro into a stub
cpufreq: s5pv210: Don't flood kernel log after cpufreq change
cpufreq: pcc-cpufreq: Fail initialization if driver cannot be registered
cpufreq: add driver for Raspberry Pi
cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading
cpufreq: imx-cpufreq-dt: Remove global platform match list
cpufreq: brcmstb-avs-cpufreq: Fix types for voltage/frequency
cpufreq: brcmstb-avs-cpufreq: Fix initial command check
cpufreq: armada-37xx: Remove set but not used variable 'freq'
cpufreq: imx-cpufreq-dt: Fix no OPPs available on unfused parts
dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage
cpufreq: Add imx-cpufreq-dt driver
clang emits a warning about a negative shift count for an
unused part of a conditional constant expression:
drivers/soc/rockchip/pm_domains.c:795:21: error: shift count is negative [-Werror,-Wshift-count-negative]
[RK3328_PD_VIO] = DOMAIN_RK3328(-1, 8, 8, false),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/soc/rockchip/pm_domains.c:129:2: note: expanded from macro 'DOMAIN_RK3328'
DOMAIN_M(pwr, pwr, req, (req) + 10, req, wakeup)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/soc/rockchip/pm_domains.c:105:33: note: expanded from macro 'DOMAIN_M'
.status_mask = (status >= 0) ? BIT(status) : 0, \
^~~~~~~~~~~
include/linux/bits.h:6:24: note: expanded from macro 'BIT'
This is a bug in clang that will be fixed in the future, but in order
to build cleanly with clang-8, it would be helpful to shut up this
warning. This file is the only instance reported by kernelci at the
moment.
The best solution I could come up with is to move the BIT() usage
out of the macro into the instantiation, so we can avoid using
BIT(-1).
Link: https://lore.kernel.org/r/20190703153112.2767411-1-arnd@arndb.de
Link: https://bugs.llvm.org/show_bug.cgi?id=38789
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
OHCI driver was converted over to use GPIO regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vwpF
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
This set of patches fixes regressions introduced in v5.2 kernel when DA8xx
OHCI driver was converted over to use GPIO regulators.
* tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da830-evm: fix GPIO lookup for OHCI
ARM: davinci: omapl138-hawk: add missing regulator constraints for OHCI
ARM: davinci: da830-evm: add missing regulator constraints for OHCI
+ Linux 5.2-rc7
Signed-off-by: Olof Johansson <olof@lixom.net>
In some software releases the firmware images are not split up with each
loadable segment in it's own file. Check the size of the loaded firmware
to see if it still contains each segment to be loaded, before falling
back to the split-out segments.
Acked-by: Andy Gross <agross@kernel.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The irqchip driver depends on the SoC specific driver, but we want
to be able to compile-test it elsewhere:
WARNING: unmet direct dependencies detected for TI_SCI_INTA_MSI_DOMAIN
Depends on [n]: SOC_TI [=n]
Selected by [y]:
- TI_SCI_INTA_IRQCHIP [=y] && TI_SCI_PROTOCOL [=y]
drivers/irqchip/irq-ti-sci-inta.o: In function `ti_sci_inta_irq_domain_probe':
irq-ti-sci-inta.c:(.text+0x204): undefined reference to `ti_sci_inta_msi_create_irq_domain'
Rearrange the Kconfig and Makefile so we build the soc driver whenever
its users are there, regardless of the SOC_TI option.
Fixes: 49b323157b ("soc: ti: Add MSI domain bus support for Interrupt Aggregator")
Fixes: f011df6179 ("irqchip/ti-sci-inta: Add msi domain support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
-----BEGIN PGP SIGNATURE-----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=3HLl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v5.3 merge window
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
* tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (30 commits)
usb: dwc3: remove unused @lock member of dwc3_ep struct
usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices
usb: Replace snprintf with scnprintf in gether_get_ifname
usb: gadget: ether: Fix race between gether_disconnect and rx_submit
usb: gadget: storage: Remove warning message
usb: dwc3: gadget: Add support for disabling U1 and U2 entries
usb: gadget: send usb_gadget as an argument in get_config_params
doc: dt: bindings: usb: dwc3: Update entries for disabling U1 and U2
usb: dwc3: qcom: Use of_clk_get_parent_count()
usb: dwc3: Fix core validation in probe, move after clocks are enabled
usb: dwc3: qcom: Improve error handling
usb: dwc3: qcom: Start USB in 'host mode' on the SDM845
usb: dwc3: qcom: Add support for booting with ACPI
soc: qcom: geni: Add support for ACPI
Revert "usb: dwc2: host: Setting qtd to NULL after freeing it"
usb: gadget: net2272: remove redundant assignments to pointer 's'
usb: gadget: Zero ffs_io_data
USB: omap_udc: Remove unneeded variable
fotg210-udc: Remove unneeded variable
usb: gadget: at91_udc: Remove unneeded variable
...
Pull ARM cpufreq changes for v5.3 from Viresh Kumar:
"This pull request contains:
- Minor fixes for brcmstb driver (Florian).
- New imx-cpufreq driver, its bindings and code around it (Leonard).
- New Raspberry Pi driver (Nicolas).
- Minor fix for s5pv210 driver (Pawel).
- Minor cleanup for armada driver (YueHaibing)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: s5pv210: Don't flood kernel log after cpufreq change
cpufreq: add driver for Raspberry Pi
cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading
cpufreq: imx-cpufreq-dt: Remove global platform match list
cpufreq: brcmstb-avs-cpufreq: Fix types for voltage/frequency
cpufreq: brcmstb-avs-cpufreq: Fix initial command check
cpufreq: armada-37xx: Remove set but not used variable 'freq'
cpufreq: imx-cpufreq-dt: Fix no OPPs available on unfused parts
dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage
cpufreq: Add imx-cpufreq-dt driver
* Auto-enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
* Don't init CNTVOFF/counter if PSCI is available
-----BEGIN PGP SIGNATURE-----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=dMJy
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-soc-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/soc
Renesas ARM Based SoC Updates for v5.3
* Auto-enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
* Don't init CNTVOFF/counter if PSCI is available
* tag 'renesas-arm-soc-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
ARM: mach-shmobile: Don't init CNTVOFF/counter if PSCI is available
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add i.MX SCU based SoC bus driver for i.MX8QXP SoC support, which
talks to SCU firmware for getting SoC ID and revision.
- Update soc-imx8 bus driver to read imx8mm soc revision from anatop.
- Add i.MX8MN SoC bus support into soc-imx8 driver.
- Various small improvements on soc-imx8 bus driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdEX9EAAoJEFBXWFqHsHzOixgIAJ5FXbnVlJdoFkfFTOqQpzM5
w0/dPoJLyZOPd42SU4zTAlj7ooPCN+ux+AvOpf4BOMMZjJ3SnKRccpA7yPrhAAyb
pjYEGJAB1bLX1B4bnGJy2lHZzZFkGEMo2rK6jUl7agLV0T5HnV0/bRtBePCei8as
AXO5VhsXqxczG0EwqkwxdLWrvlFNwTtxi9XY90h/Af/tLUwRS4/V0/btE17r/v+2
FgoCZkHiGt+zfTzDdBSc+sV1MMcSgIGHDVTIRD1x2BfMC3VBng1HZy8aVZL2f5YP
FvDeP4W91bGSlfztKxZtZI7LLQ5oAJujgJFOvtqaaRQxV8Fk7DsNeSN58c9nRf4=
=qYcp
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX driver changes for 5.3:
- Add i.MX SCU based SoC bus driver for i.MX8QXP SoC support, which
talks to SCU firmware for getting SoC ID and revision.
- Update soc-imx8 bus driver to read imx8mm soc revision from anatop.
- Add i.MX8MN SoC bus support into soc-imx8 driver.
- Various small improvements on soc-imx8 bus driver.
* tag 'imx-drivers-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: Add i.MX8MN SoC driver support
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
soc: imx: soc-imx8: Correct return value of error handle
soc: imx: soc-imx8: Avoid unnecessary of_node_put() in error handling
soc: imx: Add SCU SoC info driver support
soc: imx: Read imx8mm soc revision from anatop
Signed-off-by: Olof Johansson <olof@lixom.net>
LPC control driver changes and a fix.
-----BEGIN PGP SIGNATURE-----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=N3Jm
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/drivers
ASPEED SoC updates for 5.3
LPC control driver changes and a fix.
* tag 'aspeed-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: aspeed: lpc-ctrl: make parameter optional
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains a set of minor fixes and cleanups for core Tegra drivers.
-----BEGIN PGP SIGNATURE-----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=bqwE
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc: tegra: Changes for v5.3-rc1
This contains a set of minor fixes and cleanups for core Tegra drivers.
* tag 'tegra-for-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: Select pinctrl for Tegra194
soc/tegra: fuse: Do not log error message on deferred probe
soc/tegra: pmc: Add comments clarifying wake events
soc/tegra: pmc: Avoid crash for non-wake IRQs
soc/tegra: pmc: Fail to allocate more than one wake IRQ
Signed-off-by: Olof Johansson <olof@lixom.net>
- canvas: add support for Meson8*
-----BEGIN PGP SIGNATURE-----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=NrZO
-----END PGP SIGNATURE-----
Merge tag 'amlogic-drivers' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/drivers
soc: Amlogic driver updates for v5.3
- canvas: add support for Meson8*
* tag 'amlogic-drivers' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
soc: amlogic: canvas: add support for Meson8, Meson8b and Meson8m2
dt-bindings: soc: amlogic: canvas: document support for Meson8/8b/8m2
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add ACPI support to Qualcomm GENI SE
* Update Qualcomm Maintainers entry to remove David Brown as maintainer and
fixup typos and incorrect DT file entry
* Fixup APR domain id usage and making callbacks in non-atomic context
* Add AOSS QMP driver and bindings
* Add power domains for MSM8998 and QCS404 in QCOM RPMPD
* Add corner macros, max state support, and fixups for setting performance state
for Qcom RPMPD
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JunO
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.3
* Add ACPI support to Qualcomm GENI SE
* Update Qualcomm Maintainers entry to remove David Brown as maintainer and
fixup typos and incorrect DT file entry
* Fixup APR domain id usage and making callbacks in non-atomic context
* Add AOSS QMP driver and bindings
* Add power domains for MSM8998 and QCS404 in QCOM RPMPD
* Add corner macros, max state support, and fixups for setting performance state
for Qcom RPMPD
* tag 'qcom-drivers-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: geni: Add support for ACPI
MAINTAINERS: Remove myself as qcom maintainer
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
soc: qcom: Add AOSS QMP driver
dt-bindings: soc: qcom: Add AOSS QMP binding
qcom: apr: Make apr callbacks in non-atomic context
soc: qcom: rpmpd: Add MSM8998 power-domains
dt-bindings: power: Add rpm power domain bindings for msm8998
soc: qcom: rpmpd: Add QCS404 power-domains
dt-bindings: power: Add rpm power domain bindings for qcs404
soc: qcom: rpmpd: Modify corner defining macros
soc: qcom: rpmpd: Add support to set rpmpd state to max
soc: qcom: rpmpd: fixup rpmpd set performance state
MAINTAINER: Fix Qualcomm ETHQOS ethernet DT file
MAINTAINERS: fix typo in file name
Signed-off-by: Olof Johansson <olof@lixom.net>
gcc warns that a mising "flash" phandle node leads to undefined
behavior later:
drivers/soc/aspeed/aspeed-lpc-ctrl.c: In function 'aspeed_lpc_ctrl_probe':
drivers/soc/aspeed/aspeed-lpc-ctrl.c:201:18: error: '*((void *)&resm+8)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Only set the flash base and size if we find a phandle in the device
tree.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
tegra_powergate_sequence_power_up() powers up partition and also enables
clock & reset. However, if a controller like PCIe have multiple clocks
& resets and they need to be enabled in a sequence, driver must use
standalone function tegra_powergate_power_on() to power up partition.
Export tegra_powergate_power_on() to allow Tegra controller drivers to
unpower gate partition independent to clock & reset.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting with ACPI as the active set of configuration tables,
all; clocks, regulators, pin functions ect are expected to be at
their ideal values/levels/rates, thus the associated frameworks
are unavailable. Ensure calls to these APIs are shielded when
ACPI is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
There is common of_root for reference, no need to find it
from DT again, use of_root directly to make driver simple.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When booting with ACPI as the active set of configuration tables,
all; clocks, regulators, pin functions ect are expected to be at
their ideal values/levels/rates, thus the associated frameworks
are unavailable. Ensure calls to these APIs are shielded when
ACPI is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just two changes to make few platform data functions static, and to
call dev_info() if am437x is suspending to RTC-only mode. We want to
see this in case of issues as it depends on the board wiring for things
like DDR memory.
-----BEGIN PGP SIGNATURE-----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=+Fzf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.3/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
ti-sysc soc changes for v5.3
Just two changes to make few platform data functions static, and to
call dev_info() if am437x is suspending to RTC-only mode. We want to
see this in case of issues as it depends on the board wiring for things
like DDR memory.
* tag 'omap-for-v5.3/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
Signed-off-by: Olof Johansson <olof@lixom.net>
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
-----BEGIN PGP SIGNATURE-----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=C+f6
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.3
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
* tag 'soc-fsl-next-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qbman_portals: add APIs to retrieve the probing status
soc: fsl: qman: fixup liodns only on ppc targets
soc: fsl: dpio: Add support for memory backed QBMan portals
bus: mc-bus: Add support for mapping shareable portals
soc: fsl: dpio: Increase timeout for QBMan Management Commands
soc: fsl: add DPAA2 console support
Documentation: DT: Add entry for DPAA2 console
soc: fsl: guts: Add definition for LX2160A
Signed-off-by: Olof Johansson <olof@lixom.net>
Making memory-region and flash as optional parameter in device
tree if user needs to use these parameter through ioctl then
need to define in devicetree.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
fixes for 5.2-rc1, please pull the following:
- Florian fixes the biuctrl driver not to create an error condition/path
upon unsupported CPU and also fixes the biuctrl driver writes to used
a data barrier which is necessary given the HW block design
-----BEGIN PGP SIGNATURE-----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=VOdD
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.2/drivers-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM/ARM64/MIPS SoCs device drivers
fixes for 5.2-rc1, please pull the following:
- Florian fixes the biuctrl driver not to create an error condition/path
upon unsupported CPU and also fixes the biuctrl driver writes to used
a data barrier which is necessary given the HW block design
* tag 'arm-soc/for-5.2/drivers-fixes' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: biuctrl: Register writes require a barrier
soc: brcmstb: Fix error path for unsupported CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
The reg property represents the address and size on the bus that a
device lives, but for APR the parent is a rpmsg bus, which does not have
numerical addresses. Simply defining #address/#size-cells to 1 and 0,
respectively, to silence the compiler is not an appropriate solution.
Replace the use of "reg" with an APR specific property.
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix Kconfig warning and subsequent build errors that are caused
when PM_GENERIC_DOMAINS=y but CONFIG_PM is not set/enabled.
WARNING: unmet direct dependencies detected for PM_GENERIC_DOMAINS
Depends on [n]: PM [=n]
Selected by [m]:
- QCOM_AOSS_QMP [=m] && (ARCH_QCOM || COMPILE_TEST [=y]) && MAILBOX [=y] && COMMON_CLK [=y]
Fixes these build errors:
../drivers/base/power/domain.c: In function ‘genpd_queue_power_off_work’:
../drivers/base/power/domain.c:485:13: error: ‘pm_wq’ undeclared (first use in this function)
queue_work(pm_wq, &genpd->power_off_work);
../drivers/base/power/domain.c:485:13: note: each undeclared identifier is reported only once for each function it appears in
../drivers/base/power/domain.c: In function ‘genpd_dev_pm_qos_notifier’:
../drivers/base/power/domain.c:675:25: error: ‘struct dev_pm_info’ has no member named ‘ignore_children’
if (!dev || dev->power.ignore_children)
../drivers/base/power/domain.c: In function ‘rtpm_status_str’:
../drivers/base/power/domain.c:2754:16: error: ‘struct dev_pm_info’ has no member named ‘runtime_error’
if (dev->power.runtime_error)
../drivers/base/power/domain.c:2756:21: error: ‘struct dev_pm_info’ has no member named ‘disable_depth’
else if (dev->power.disable_depth)
../drivers/base/power/domain.c:2758:21: error: ‘struct dev_pm_info’ has no member named ‘runtime_status’
else if (dev->power.runtime_status < ARRAY_SIZE(status_lookup))
../drivers/base/power/domain.c:2759:31: error: ‘struct dev_pm_info’ has no member named ‘runtime_status’
p = status_lookup[dev->power.runtime_status];
../drivers/base/power/domain_governor.c: In function ‘default_suspend_ok’:
../drivers/base/power/domain_governor.c:82:17: error: ‘struct dev_pm_info’ has no member named ‘ignore_children’
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Always On Subsystem (AOSS) Qualcomm Messaging Protocol (QMP) driver
is used to communicate with the AOSS for certain side-channel requests,
that are not available through the RPMh interface.
The communication is a very simple synchronous mechanism of messages
being written in message RAM and a doorbell in the AOSS is rung. As the
AOSS has processed the message length is cleared and an interrupt is
fired by the AOSS as acknowledgment.
The driver exposes the QDSS clock as a clock and the low-power state
associated with the remoteprocs in the system as a set of power-domains.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
APR communication with DSP is not atomic in nature.
Its request-response type. Trying to pretend that these are atomic
and invoking apr client callbacks directly under atomic/irq context has
endless issues with soundcard. It makes more sense to convert these
to nonatomic calls. This also coverts all the dais to be nonatomic.
All the callbacks are now invoked as part of rx work queue.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently there is no way to distinguish if the SoC entered DS0
mode or the RTC only mode. Hence add a print before entering
the RTC only mode.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Auto-enable support for the RZ/A1 Interrupt Controller when configuring
a kernel which supports RZ/A1H or RZ/A2M SoCs.
Keep selects sorted while at it.
This is similar to how interrupt controllers for other Renesas SoCs are
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The comment "No QE ever has fewer than 28 SNUMs" is false; e.g. the
MPC8309 has 14. The code path returning -EINVAL is also a recipe for
instant disaster, since the caller (qe_snums_init) uncritically
assigns the return value to the unsigned qe_num_of_snum, and would
thus proceed to attempt to copy 4GB from snum_init_46[] to the snum[]
array.
So fold the handling of the legacy fsl,qe-num-snums into
qe_snums_init, and make sure we do not end up using the snum_init_46
array in cases other than the two where we know it makes sense.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add driver support for the newly introduced fsl,qe-snums property.
Conveniently, of_property_read_variable_u8_array does exactly what we
need: If the property fsl,qe-snums is found (and has an allowed size),
the array of values get copied to snums, and the return value is the
number of snums - we cannot assign directly to num_of_snums, since we
need to check whether the return value is negative.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The 'try of_find_compatible_node(NULL, NULL, "fsl,qe"), fall back to
of_find_node_by_type(NULL, "qe")' pattern is repeated five
times. Factor it into a common helper.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The current array of struct qe_snum use 256*4 bytes for just keeping
track of the free/used state of each index, and the struct layout
means there's another 768 bytes of padding. If we just unzip that
structure, the array of snum values just use 256 bytes, while the
free/inuse state can be tracked in a 32 byte bitmap.
So this reduces the .data footprint by 1760 bytes. It also serves as
preparation for introducing another DT binding for specifying the snum
values.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The local variable snum_init has no reason to have static storage duration.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license rev 2 and only
rev 2 as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.583753585@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.745679586@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent changes have made it much more probable that clocks are not
available yet when the FUSE driver is first probed. However, that is a
situation that the driver can cope with just fine.
To avoid confusion, don't output an error when this happens.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add some comments to clarify the purpose of the wake event support
implemented in the PMC driver.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For interrupts that are not wakeup sources but that may end up getting
mapped through the PMC as interrupt parent (this can happen for GPIOs),
return early in order to avoid a subsequent crash from an out-of-bounds
access to the register region.
Reported-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code currently doesn't support allocating more than one wake IRQ at
a time. Detect this situation and error out. Also make sure to output a
warning when that happens to help track down callers.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current implementation of i.MX8 SoC driver returns -ENODEV
for all cases of error during initialization, this is incorrect.
This patch fixes them using correct return value according
to different errors.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
of_node_put() is called after of_match_node() successfully called,
then in the following error handling, of_node_put() is called again
which is unnecessary, this patch adjusts the location of of_node_put()
to avoid such scenario.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add i.MX SCU SoC info driver to support i.MX8QXP SoC, introduce
driver dependency into Kconfig as CONFIG_IMX_SCU must be
selected to support i.MX SCU SoC driver, also need to use
platform driver model to make sure IMX_SCU driver is probed
before i.MX SCU SoC driver.
With this patch, SoC info can be read from sysfs:
i.mx8qxp-mek# cat /sys/devices/soc0/family
Freescale i.MX
i.mx8qxp-mek# cat /sys/devices/soc0/soc_id
0x2
i.mx8qxp-mek# cat /sys/devices/soc0/machine
Freescale i.MX8QXP MEK
i.mx8qxp-mek# cat /sys/devices/soc0/revision
1.1
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.709316650@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 107 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.615055994@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the shared cx/mx and sensor sub-system's cx and mx
power-domains found on MSM8998.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the shared cx/mx and the low-power-island's cx and mx power-domains
found on QCS404.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibi: Fixup corner/vfc with vlfl/vfl]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
QCS404 uses individual resource type magic for each power-domain, so
adjust the macros slightly to make them reusable for this.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibi: Extend rpmpd corner pair to a generic rpmpd pair]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
rpmpd max state varies across SoCs and SoC families, add support
in the driver to make it SoC/SoC family specific
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Remoteproc q6v5-mss calls set_performance_state with INT_MAX on
rpmpd. This is currently ignored since it is greater than the
max supported state. Fixup rpmpd state to max if the required
state is greater than all the supported states.
Fixes: 075d3db8d1 ("soc: qcom: rpmpd: Add support for get/set performance state")
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
There is a spelling mistake in a pr_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The __dma_request_channel() prototype has been changed to help to do
device node validation, thus we can use dma_request_channel() instead
of __dma_request_channel() to keep kernel bisectable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The canvas IP on Meson8, Meson8b and Meson8m2 is mostly identical to the
one on GXBB and newer. The only known difference so far is that that the
"endianness" bits are not supported on Meson8m2 and earlier.
Add new compatible strings and a check in meson_canvas_config() to
validate that the endianness bits cannot be configured on the 32-bit
SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a couple of new APIs to check the probing status of the required
cpu bound qman and bman portals:
'int bman_portals_probed()' and 'int qman_portals_probed()'.
They return the following values.
* 1 if qman/bman portals were all probed correctly
* 0 if qman/bman portals were not yet probed
* -1 if probing of qman/bman portals failed
Portals are considered successful probed if no error occurred during
the probing of any of the portals and if enough portals were probed
to have one available for each cpu.
The error handling paths were slightly rearranged in order to fit this
new functionality without being too intrusive.
Drivers that use qman/bman portal driver services are required to use
these APIs before calling any functions exported by these drivers or
otherwise they will crash the kernel.
First user will be the dpaa1 ethernet driver, coming in a subsequent
patch.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
ARM SoCs use SMMU so the liodn fixup done in the qman driver is no
longer making sense and it also breaks the ICID settings inherited
from u-boot. Do the fixups only for PPC targets.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
NXP devices with QBMan version 5 and above can enable software
portals that are memory backed. This allows the portal to be
mapped as cacheable/sharable (same as all normal memory) so
that portals can freely migrate between cores and clusters
in the SoC. The driver will enable this mode by default when
appropriate HW support is detected.
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The timeout for QBMan Management Commands can falsely trigger on a
busy system. This patch doubles the timeout to avoid the
false error reports
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
This patch adds DPAA2 MC and AIOP console log support.
The platform driver probes on the "fsl,dpaa2-console" device tree node
which describes the base firmware address needed in order to infer the
start address of both firmware logs: MC and AIOP.
It then exports two misc char devices which can be used to dump
the needed logs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Adding compatible string "lx2160a-dcfg" to
initialize guts driver for lx2160 and SoC die
attribute definition for LX2160A
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The BIUCTRL register writes require that a data barrier be inserted
after comitting the write to the register for the block to latch in the
recently written values. Reads have no such requirement and are not
changed.
Fixes: 34642650e5 ("soc: Move brcmstb to bcm/brcmstb")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In case setup_hifcpubiuctrl_regs() returns an error, because of e.g:
an unsupported CPU type, just catch that error and return instead of
blindly continuing with the initialization. This fixes a NULL pointer
de-reference with the code continuing without having a proper array of
registers to use.
Fixes: 22f7a9116e ("soc: brcmstb: Correct CPU_CREDIT_REG offset for Brahma-B53 CPUs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Like on imx6/7 we can read version information from a register in
anatop, and in the same format.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.
Add a small driver which checks speed grading from nvmem cells before
registering cpufreq-dt.
This driver allows unlocking all frequencies for imx8mm and imx8mq and
could be applied to other chips like imx7d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
NXP/FSL soc driver fixes for v5.1
QE drivers
- Fix an error path in qe_pin_request()
* tag 'soc-fsl-fix-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc/fsl/qe: Fix an error code in qe_pin_request()
Signed-off-by: Olof Johansson <olof@lixom.net>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers
-----BEGIN PGP SIGNATURE-----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=YSfu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----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=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
- Fix recent regression causing kernels built with CONFIG_PM
unset to crash on systems that support the Performance and
Energy Bias Hint (EPB) by avoiding to compile the EPB-related
code depending on CONFIG_PM when it is unset (Rafael Wysocki).
- Clean up the transition notifier invocation code in the cpufreq
core and change some users of cpufreq transition notifiers
accordingly (Viresh Kumar).
- Change MAINTAINERS to cover the schedutil governor as part of
cpufreq (Viresh Kumar).
- Simplify cpufreq_init_policy() to avoid redundant computations
(Yue Hu).
- Add explanatory comment to the cpufreq core (Rafael Wysocki).
- Introduce a new flag, GENPD_FLAG_RPM_ALWAYS_ON, to the generic
power domains (genpd) framework along with the first user of it
(Leonard Crestez).
-----BEGIN PGP SIGNATURE-----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=LqTN
-----END PGP SIGNATURE-----
Merge tag 'pm-5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These fix a recent regression causing kernels built with CONFIG_PM
unset to crash on systems that support the Performance and Energy Bias
Hint (EPB), clean up the cpufreq core and some users of transition
notifiers and introduce a new power domain flag into the generic power
domains framework (genpd).
Specifics:
- Fix recent regression causing kernels built with CONFIG_PM unset to
crash on systems that support the Performance and Energy Bias Hint
(EPB) by avoiding to compile the EPB-related code depending on
CONFIG_PM when it is unset (Rafael Wysocki).
- Clean up the transition notifier invocation code in the cpufreq
core and change some users of cpufreq transition notifiers
accordingly (Viresh Kumar).
- Change MAINTAINERS to cover the schedutil governor as part of
cpufreq (Viresh Kumar).
- Simplify cpufreq_init_policy() to avoid redundant computations (Yue
Hu).
- Add explanatory comment to the cpufreq core (Rafael Wysocki).
- Introduce a new flag, GENPD_FLAG_RPM_ALWAYS_ON, to the generic
power domains (genpd) framework along with the first user of it
(Leonard Crestez)"
* tag 'pm-5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
soc: imx: gpc: Use GENPD_FLAG_RPM_ALWAYS_ON for ERR009619
PM / Domains: Add GENPD_FLAG_RPM_ALWAYS_ON flag
cpufreq: Update MAINTAINERS to include schedutil governor
cpufreq: Don't find governor for setpolicy drivers in cpufreq_init_policy()
cpufreq: Explain the kobject_put() in cpufreq_policy_alloc()
cpufreq: Call transition notifier only once for each policy
x86: intel_epb: Take CONFIG_PM into account
This allows PU domain to be turned off in suspend and save power.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the system coprocessor managing the range allocation of the
inputs to Interrupt Aggregator, it is difficult to represent
the device IRQs from DT.
The suggestion is to use MSI in such cases where devices wants
to allocate and group interrupts dynamically.
Create a MSI domain bus layer that allocates and frees MSIs for
a device.
APIs that are implemented:
- ti_sci_inta_msi_create_irq_domain() that creates a MSI domain
- ti_sci_inta_msi_domain_alloc_irqs() that creates MSIs for the
specified device and resource.
- ti_sci_inta_msi_domain_free_irqs() frees the irqs attached to the device.
- ti_sci_inta_msi_get_virq() for getting the virq attached to a specific event.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When enabling ARCH_SUNXI from allnoconfig, SUNXI_SRAM is enabled, but
not REGMAP_MMIO, so the kernel fails to link with an undefined reference
to __devm_regmap_init_mmio_clk. Select REGMAP_MMIO, as suggested in
drivers/base/regmap/Kconfig.
This creates the following dependency loop:
drivers/of/Kconfig:68: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:63: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by SUNXI_SRAM
drivers/soc/sunxi/Kconfig:4: symbol SUNXI_SRAM is selected by USB_MUSB_SUNXI
drivers/usb/musb/Kconfig:63: symbol USB_MUSB_SUNXI depends on GENERIC_PHY
drivers/phy/Kconfig:7: symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
drivers/phy/broadcom/Kconfig:29: symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
drivers/net/phy/Kconfig:12: symbol MDIO_BUS default is visible depending on PHYLIB
drivers/net/phy/Kconfig:181: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:18: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:24: symbol ARC_EMAC depends on OF_IRQ
To fix the circular dependency, make USB_MUSB_SUNXI select GENERIC_PHY
instead of depending on it. This matches the use of GENERIC_PHY by all
but two other drivers.
Cc: <stable@vger.kernel.org> # 4.19
Fixes: 5828729beb ("soc: sunxi: export a regmap for EMAC clock reg on A64")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes build break:
scripts/kconfig/conf --allnoconfig Kconfig
drivers/soc/Kconfig:24: 'menu' in different file than 'menu'
drivers/soc/aspeed/Kconfig:1: location of the 'menu'
drivers/Kconfig:233: 'menu' in different file than 'menu'
drivers/soc/aspeed/Kconfig:1: location of the 'menu'
<none>:34: syntax error
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAly/dWgQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgdfoB/4irvAihmabor/KyjEeBZMO7NDb4Z+WDOhQ
3dsIsqotPwza4m81ERlKOVdXEYqd+692Jat8fLHF4DgL9NjKPLARDpTg6MeWXB8L
z4BaSwrA5WC9VqbnbxbjWMdk2uJPo52YngLQeznsDFcGJdqHux1XGU/kICV0Tkqt
DXdCbRzVIC+9GHHSG8VVPyVIDkFsFxFSb6ENOESh/W9SqKg1uHZBuZy+WCoojrKK
C4IU4XxUeZCLJGu63F5VpzVaqcw7pMvff0qig3PDr426mLS146wdQVtXMsdH2cf3
Sz+mqXkuA2ORyD3CRhRRVnckALrw5aFtLGkOEWlUKNY59zElvoyU
=4KwL
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rockchip-drivers-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/drivers
Select correct pwm solution by default.
* tag 'v5.2-rockchip-drivers-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: Set the proper PWM for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
* Update MAINTAINERS for Andy Gross's new email address
* Add support for mmap in RMTFS
* Fixup for QMI to change txn wait to non-interruptible
* Fixup for error code in probe of cmd-db
* Fixup for slot number check in RMPH-RSC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nsKB
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.2
* Update MAINTAINERS for Andy Gross's new email address
* Add support for mmap in RMTFS
* Fixup for QMI to change txn wait to non-interruptible
* Fixup for error code in probe of cmd-db
* Fixup for slot number check in RMPH-RSC
* tag 'qcom-drivers-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
MAINTAINERS: Update email for Qualcomm SoC maintainer
drivers: soc: qcom: rpmh-rsc: Correct check for slot number
soc: qcom: cmd-db: Fix an error code in cmd_db_dev_probe()
soc: qcom: qmi: Change txn wait to non-interruptible
soc: qcom: rmtfs: Add support for mmap functionality
Signed-off-by: Olof Johansson <olof@lixom.net>
Create a SoC folder for the ASPEED parts and place the misc drivers
currently present into this folder. These drivers are not generic part
drivers, but rather only apply to the ASPEED SoCs.
Signed-off-by: Patrick Venture <venture@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
- A series from Aisheng to generalize the SCU powerdomain driver
for easier adding new SCU based platforms like imx8qm.
- Add a generic i.MX8 SoC driver for reporting SoC and platform
information.
- Replace explicit polling loop with a call to regmap_read_poll_timeout()
for gpcv2 driver to avoid code repetition.
- Use devm_platform_ioremap_resource() to simplify gpc/gpcv2 driver
code a bit.
- Add general IRQ support for imx-scu driver, so that interrupt of
device like RTC, thermal and watchdog can be handled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvWKIAAoJEFBXWFqHsHzOeCQH/j/lgujJU9RnyY2CFTelMyad
uTKEUgk2vvbswBdFMaS7xAvbni24GOxUdKUYJul0oz5jBnK4wKmf6VY7TYMQ8Qht
hsdp0dsHHgI1qysOiOSxidhIN/2aXFl/hSoF8FT/9m0qXqnmvoHGFQT0YoMGwznS
+7tHuUt5cjUG/r5DMM6GOzI/w6K1of6RGGsLWvYeuy7OeoDhI2Gl5gtK+qxik98J
qC9UM64jO93rmXebJuG+9ZNJ0FFATrBMboMB3a7rA3t9RvkAFKEuVRp3USPuj1ek
TxNusTtkQwCeujy9QZu/eB/oUrScEbzJuw+sp0l69C9T2D44ucZLFbHixnwbigM=
=1wlN
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers change for 5.2:
- A series from Aisheng to generalize the SCU powerdomain driver
for easier adding new SCU based platforms like imx8qm.
- Add a generic i.MX8 SoC driver for reporting SoC and platform
information.
- Replace explicit polling loop with a call to regmap_read_poll_timeout()
for gpcv2 driver to avoid code repetition.
- Use devm_platform_ioremap_resource() to simplify gpc/gpcv2 driver
code a bit.
- Add general IRQ support for imx-scu driver, so that interrupt of
device like RTC, thermal and watchdog can be handled.
* tag 'imx-drivers-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: Add generic i.MX8 SoC driver
firmware: imx: enable imx scu general irq function
soc: imx: gpcv2: use devm_platform_ioremap_resource() to simplify code
soc: imx: gpc: use devm_platform_ioremap_resource() to simplify code
firmware: imx: scu-pd: decouple the SS information from domain names
firmware: imx: scu-pd: add specifying the base of domain name index support
firmware: imx: scu-pd: use bool to set postfix
soc: imx: gpcv2: Make use of regmap_read_poll_timeout()
Signed-off-by: Olof Johansson <olof@lixom.net>
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
-----BEGIN PGP SIGNATURE-----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=0U95
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/soc
This modernizes the IXP4xx platform and adds initial Device Tree
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
* tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: (31 commits)
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
ARM: ixp4xx: Move IXP4xx QMGR and NPE headers
ARM: ixp4xx: Move NPE and QMGR to drivers/soc
ARM: dts: Add some initial IXP4xx device trees
ARM: ixp4xx: Add device tree boot support
ARM: ixp4xx: Add DT bindings
gpio: ixp4xx: Add OF probing support
gpio: ixp4xx: Add DT bindings
clocksource/drivers/ixp4xx: Add OF initialization support
clocksource/drivers/ixp4xx: Add DT bindings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Besides a couple of fixes to better cope with deferred probing, this set
of patches also implements the acquire/release protocol for resets used
during powergate operations. This is necessary to allow these resets to
be temporarily shared with other devices that may also need to control
these resets.
-----BEGIN PGP SIGNATURE-----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=27G2
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.2-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.2-rc1
Besides a couple of fixes to better cope with deferred probing, this set
of patches also implements the acquire/release protocol for resets used
during powergate operations. This is necessary to allow these resets to
be temporarily shared with other devices that may also need to control
these resets.
* tag 'tegra-for-5.2-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc/tegra: pmc: Implement acquire/release for resets
reset: Add acquire/release support for arrays
reset: Add acquired flag to of_reset_control_array_get()
reset: add acquired/released state for exclusive reset controls
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add support for ZynqMP fpga manager
- Defer some probes which depends on firmware driver to be ready
- Debugfs fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly0QlMACgkQykllyylKDCFYngCfZOByHuyiliPv+PSa6KCtCics
ccgAn3YC1zEfvh8pmj2t0cvO/EpV2pXC
=HBAL
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-for-v5.2' of https://github.com/Xilinx/linux-xlnx into arm/drivers
arm64: zynqmp: SoC changes for v5.2
- Add support for ZynqMP fpga manager
- Defer some probes which depends on firmware driver to be ready
- Debugfs fix
* tag 'zynqmp-soc-for-v5.2' of https://github.com/Xilinx/linux-xlnx:
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
drivers: Defer probe if firmware is not ready
firmware: xilinx: fix debugfs write handler
Signed-off-by: Olof Johansson <olof@lixom.net>
This series adds support for am437x RTC-only mode in suspend. In the
RTC-only mode suspend, everything is shut down except the RTC. This
makes the power consumption very low for suspend mode.
To support RTC-only mode, we need to export omap_rtc_power_off_program()
from the rtc driver and improve PM code to save and restore the wkup
domain context. As RTC-only mode depends on the device being wired
properly for things like memory, we need to also check for the machine
type before we allow it. We also need to run DDR3 hardware leveling on
resume.
Note that there is a trivial merge conflict between the RTC branch
and these changes where the RTC branch makes tm2bcd() a void function
and the error handling parts can be just dropped.
-----BEGIN PGP SIGNATURE-----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=yNbG
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/am4-pm-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
PM changes for am335x and am437x
This series adds support for am437x RTC-only mode in suspend. In the
RTC-only mode suspend, everything is shut down except the RTC. This
makes the power consumption very low for suspend mode.
To support RTC-only mode, we need to export omap_rtc_power_off_program()
from the rtc driver and improve PM code to save and restore the wkup
domain context. As RTC-only mode depends on the device being wired
properly for things like memory, we need to also check for the machine
type before we allow it. We also need to run DDR3 hardware leveling on
resume.
Note that there is a trivial merge conflict between the RTC branch
and these changes where the RTC branch makes tm2bcd() a void function
and the error handling parts can be just dropped.
* tag 'omap-for-v5.2/am4-pm-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: sleep43xx: Run EMIF HW leveling on resume path
memory: ti-emif-sram: Add ti_emif_run_hw_leveling for DDR3 hardware leveling
soc: ti: pm33xx: AM437X: Add rtc_only with ddr in self-refresh support
soc: ti: pm33xx: Move the am33xx_push_sram_idle to the top
ARM: OMAP2+: pm33xx: Add support for rtc+ddr in self refresh mode
rtc: OMAP: Add support for rtc-only mode
Signed-off-by: Olof Johansson <olof@lixom.net>
- socinfo: support new SoCs / packages
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEe4dGDhaSf6n1v/EMWTcYmtP7xmUFAlyei14ACgkQWTcYmtP7
xmWvfg/+P+s9EJF9w9iSMWc6DCfwvufJRfPBO6T8MGoTSHzR8vPoCRDnwFtIhzh5
ZOMbGWeutXv7cQynbbqWsSTi+qY9ye7JjEW142Abxa2bMc51hxWsR9Y3Sxt/tUam
KbikqYuyv7svSPoxpucLi30ykcti2BFdHMrfuNhM+Ml6IuFVvOJ1bJA5scQXVB7l
49blLz9VTtAkoPRD8XBd+otDntb/8XZxfUyD2FANZhauXNiriQxAzOaauru7iMz0
V1Nd5MzwW3q+SQ4Qn1iohCfAVmPdgqFmq1DItJXm0iaaYF/fxPRj7Sql5NVx+M2O
iL6bozt/aAJRVcleGiS78jTawQh2FTE1h8NuVGDmGU2bg43E75DhbBeU1M95zZyM
uMH96ofjejF2SKPFT5jl67qDCrOj0QwInM5Nivoa0lYDNhS+2ZXN/S7Bw8XF3KfO
Igxub9/TKzSAVdB04V6CvT+v0YZW/f2exB0/KnIcmQC0tFiEf/CEfZb5QM4W5l5b
BGGH+VyJaHNXobmzhaVOCapy2TlEIjOk5aVKu52B7Q7XsPuRs7guVWuIdqAt1tH8
lclXq3tju9shqfXJPtZiTvZzQbhElQZdNlcyDl1kSCMjCdqSR5lW8hfmEF//lU2F
qPI5W3w73xkNCSFwCgbC1DYw8/N5aum8dIe28bz6ZKvsNyY+jV4=
=rHNh
-----END PGP SIGNATURE-----
Merge tag 'amlogic-drivers' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/drivers
soc: Amlogic updates for v5.2
- socinfo: support new SoCs / packages
* tag 'amlogic-drivers' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
meson-gx-socinfo: add missing of_node_put after of_device_is_available
soc: amlogic: gx-socinfo: Add new SoC IDs and Packages IDs
soc: amlogic: gx-socinfo: Add mask for each SoC packages
Signed-off-by: Olof Johansson <olof@lixom.net>
This makes the queue manager driver able to probe from the device
tree. It only needs to get a memory resource and two interrupts
and the platform device provides these as resources, so all is
pretty simple.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the NPE driver able to probe from the device tree.
It only needs to get three memory resources and the plaform
device provide these, so all is pretty simple.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using hardcoded base address implicitly
obtained through <linux/io.h>, pass the physical base
for the QMGR block as a memory resource and remap
it in the driver.
Also pass the two IRQs as resources and obtain them
in the driver.
Use devm_* accessors and simplify the error path in the
process. Drop memory region request as this is done by
the devm_ioremap* functions.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These former inlines turn out to be unused in the kernel.
If they are needed in the future, they can be resurrected
by reverting or studying this commit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These inline functions immediately exploit the static ioremaps
for the queue manager memory region. This does not work with
multiplatform where everything need to be dynamically remapped,
so get rid of these inlines and create new exports for those
used by other drivers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using hardcoded base addresses implicitly
obtained through <linux/io.h>, pass the physical base
for the three NPE blocks as memory resources and remap
these in the driver.
Drop the memory request region business, this will
anyways be done by devm_* remapping functions.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of registering everything related to the QMGR
unconditionally in the module_init() call (which will
never work with multiplatform) create a platform device
and probe the QMGR like any other device.
Put the device second in the list of devices added for
the platform so it is there when the dependent network
and crypto drivers probe later on.
This probe() path will not be taken unconditionally on
device tree boots, so remove the DT guard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of registering everything related to the NPE
unconditionally in the module_init() call (which will
never work with multiplatform) create a platform device
and probe the NPE like any other device.
Put the device first in the list of devices added for
the platform so it is there when the dependent network
and crypto drivers probe later on.
This probe() path will not be taken unconditionally on
device tree boots, so remove the DT guard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the IXP4xx Queue Manager and Network Processing
Engine headers out of the <mack/*> include path as that is
incompatible with multiplatform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Network Processing Engine and Queue Manager are
versatile firmware components used by several IXP4xx
drivers.
Drivers are relying on getting access to these components
using <mach/*> headers which does not work with
multiplatform. We need to find a better place for the
drivers to live.
Let's first move them to drivers/soc and the start to
refactor a bit by passing resources and moving headers.
This patch introduce static IRQ assignments but that
will be fixed by later patches in this series.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add generic i.MX8 SoC driver along with the i.MX8MQ SoC specific code.
For now, only i.MX8MQ revision B1 is supported. For any other, i.MX8MQ
revision it will print 'unknown'.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 8df127456f ("soc/tegra: pmc: Enable XUSB partitions on boot")
was added as a workaround to ensure that the XUSB powergates or domains
were turned on early during boot because as this time the Tegra XHCI
driver did not handle the power domains at all. Now that the Tegra XHCI
driver has been updated to properly managed the power domains, the
workaround to enable the XUSB power domain early has been removed. This
also means that we can now move the initialisation of the powergates
into the PMC driver probe. Therefore, move the powergate initialisation
into the PMC driver probe and return any errors detected. To handle any
errors, functions to cleanup and remove any power-domains registered
with the generic power-domain framework have been added.
Finally the initialisation of the 'powergates_available' bitmask is kept
in the PMC early init function to allow the legacy PMC powergate APIs to
be called during early boot for enabling secondary CPUs on 32-bit Tegra
devices.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 5f84bb1a40 ("soc/tegra: pmc: Add sysfs entries for reset info")
added sysfs entries for Tegra reset source and level. However, these
sysfs are not removed on error and so if the registering of PMC device
is probe deferred, then the next time we attempt to probe the PMC device
warnings such as the following will be displayed on boot ...
sysfs: cannot create duplicate filename '/devices/platform/7000e400.pmc/reset_reason'
Fix this by calling device_remove_file() for each sysfs entry added on
failure. Note that we call device_remove_file() unconditionally without
checking if the sysfs entry was created in the first place, but this
should be OK because kernfs_remove_by_name_ns() will fail silently.
Fixes: 5f84bb1a40 ("soc/tegra: pmc: Add sysfs entries for reset info")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
