Just like with ctrl events, drivers may want to get called back on
listener add / remove for other event types too. Rather then special
casing all of this in subscribe / unsubscribe event it is better to
use ops for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver was severely broken. This patch makes it work again, and updates
it to the latest V4L2 frameworks (except for videobuf2). It passes the
v4l2-compliance tests and it now handles suspend/resume correctly.
Several custom controls are replaced by new standard controls, only the
USB_ALTERNATE control remains.
Tested with the Hanse HVS-CM500PC USB microscope.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The et61x251 has been deprecated for a couple of releases now, as all
devices it supports are also supported by gspca_etoms, and it has not
seen any maintenance in years. So now it is time to remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note like all info on the pac73xx chips, this info was found by trial and
error, so it is not necessarily 100% correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch sometimes the camera would run out of bandwidth when
running at 640x480@30.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can only control the clockdivider to control exposure on the pac7311,
making our expo control coarse, switch to an autogain algorithm optimized for
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the pac7302 and pac7311 drivers are split, they no longer
share there control settings, so there is no need to scale the controls
to register values, instead make them reflect the registers directly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It turns out that the flush to sensor command needs to be done per register
bank. We were missing one such flush in set_exposure, causing exposure changes
to only show up when another setting in the same bank also got changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pac7302 and pac7311 driver still contains some comments from before
they were separated, such as marking certain functions 7302 or 7311 only,
with the new split drivers these make no sense, remove them.
Also removed the empty/unused sd_stop0 function from pac7311.c
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow users of gspca/autogain_functions.h to declare which of the autogain
algoritms they are going to use. This allows us to remove the hacks from
drivers which don't use coarse_grained_expo_autogain.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prior to this patch the stk-webcam driver was enabling the vflip and mirror
bits in the sensor by default. Which only is the right thing to do if the
sensor is actually mounted upside down, which it usually is not.
Actually we've received upside down reports for both usb-ids which this
driver supports, one for an "ASUSTeK Computer Inc." "A3H" laptop with
a build in 174f:a311 webcam, and one for an "To Be Filled By O.E.M."
"Z96FM" laptop with a build in 05e1:0501 webcam.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added hardware seek support based on information gleaned from the
GPLv2 driver available here:
http://sourceforge.net/projects/av-usbradio/
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to an older driver by Faidon Liambotis <paravoid@debian.org> (as noted
in the radio-mr800 comment block at the start) for figuring out how to get the
signal/stereo state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement the control framework and update to the latest V4L2 framework.
The v4l2-compliance tool now runs without errors.
Fixed bad g/s_tuner handling with respect to mono/stereo.
Support control events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If there is an error when creating controls the v4l2_ctrl_handler_free
function must be called.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When creating 64 bit integer controls make sure the max and step
values are 0 (as 64 bit controls do not have ranges).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver now complies with the v4l2-compliance tests and uses the v4l2
frameworks correctly.
It has been tested with the radio-keene FM transmitter as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exposure of Omnivision sensors is defined by the registers 07, 10 and 04.
This patch updates the registers 10 and 04 before using the registers 2d
and 2e (dummy lines).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Telling the bridge to update the sensor when setting the exposure or the gain
is not needed when the image transfer is not started.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c interface speed was set to 400 Kb/s while it is 100 Kb/s
for most sensors.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The table did not contain the sensor mt9vprb.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error messages in stable kernel releases must be output by 'pr_err'.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At the point of the call to video_register_device, both dev->vbi_dev and
dev->vdev have been allocated, and so should be freed on failure. The
error-handling code is moved to the end of the function, to avoid code
duplication.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"stat" is always zero here. The condition used to be needed, but we
shifted stuff around in 0f0b270f90 "[media] ngene: CXD2099AR Common
Interface driver".
This doesn't change how the code works, it's just a bit tidier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The saa7164_vbi_stop_port() changes the SAA_ERR_ALREADY_STOPPED result
code to -EIO before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the warning:
In file included from /home/lyakh/software/project/24/src/linux-2.6/drivers/media/video/v4l2-subdev.c:29:
linux-2.6/include/media/v4l2-ctrls.h:497: warning: 'struct file' declared inside parameter list
linux-2.6/include/media/v4l2-ctrls.h:497: warning: its scope is only this definition or declaration, which is probably not what you want
linux-2.6/include/media/v4l2-ctrls.h:505: warning: 'struct file' declared inside parameter list
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was inadvertently introduced when the integer menu control was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those fields are meaningless for such control types, and the control framework
should zero them. Otherwise v4l2-compliance will complain about non-zero
min/max/step/def fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the vidioc_default implementation doesn't support the ioctl, then drivers
must return -ENOTTY instead of -EINVAL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both radio-keene and dsbr100 did one v4l2_device_get too many. Thus the refcount
never became 0 and that causes a memory leak.
Also updated the V4L2 framework documentation accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
buf[] is a 4 character array. Perhaps this was some debugging code from
back in the day?
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The output of "make versioncheck" told us that the file
drivers/media/dvb/ddbridge/ddbridge-code.c has a incorrect include of
version.h:
linux/drivers/media/dvb/ddbridge/ddbridge-core.c: 34 linux/version.h not
needed.
After take a look in the code, we can agree to remove it.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The output of "make versioncheck" told us that:
drivers/media/radio/radio-keene.c: 31 linux/version.h not needed.
After take a look in the code, we can agree to remove it.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The output of "make versioncheck" told us that:
drivers/media/video/adp1653.c: 37 linux/version.h not needed.
After we take a look at the code, we can afree to remove it.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Marcos:
> The output of "make versioncheck" told us that:
>
> drivers/staging/media/easycap/easycap_ioctl.c: 2442: need linux/version.h
Now that drivers/media/video/v4l2-ioctl.c fills cap->version:
case VIDIOC_QUERYCAP:
{
struct v4l2_capability *cap = (struct v4l2_capability *)arg;
if (!ops->vidioc_querycap)
break;
cap->version = LINUX_VERSION_CODE;
V4L2 drivers that use video_ioctl2() shouldn't initialize it anymore.
Reported-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Marcos:
On 04-18-2012 01:30, Marcos Paulo de Souza wrote:
> The output of "make versioncheck" told us that:
>
> drivers/media/video/tlg2300/pd-video.c: 1669: need linux/version.h
>
> If we take a look at the code, we can see that this file uses the macro
> KERNEL_VERSION.
The V4L2 core now fills it automatically, so drivers shouldn't touch on
cap->version anymore.
Reported by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
