This patch fixes the following checkpatch errors:
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: space prohibited after that '!' (ctx:BxW)
+ if (! netif_carrier_ok(tp->dev) &&
^
ERROR: space required after that ',' (ctx:VxV)
+#define GET_REG32_LOOP(base,len) \
^
ERROR: "(foo*)" should be "(foo *)"
+ memcpy(data, ((char*)&val) + b_offset, b_count);
ERROR: do not use assignment in if condition
+ if ((err = tg3_do_mem_test(tp, mem_tbl[i].offset,
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 52cdf8526f,
entitled "tg3: Prevent a PCIe tx glitch". The problem does not have
any visible side-effects and happens too early for the driver to do
anything about it. The proper place for this code is within the
device's bootcode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code so that the driver version can be reported
to the firmware in addition to the current use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is coded to refuse to attach to 5717 serdes devices. Now that the
hardware is better supported, we can relax this restriction. This patch
also fixes a recently introduced bug which will cause serdes parallel
detection not to work with 5780 class devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_start_xmit_dma_bug() function was missing code to process IPv6
TSO packets. This patch adds the missing support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt coalescing setup code used the TG3_FLG2_USING_MSIX flag to
determine whether or not to configure the rx coalescing parameters.
This is incorrect for the single MSI-X vector case. This patch changes
the code to look at the TG3_FLG3_ENABLE_RSS instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 2601d8a004. A
spectacular set of coincidences made it look as though the table was
setup incorrectly. The original version was correct.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 72dccb01e8 (bnx2: Update vlan_features)
In order to enable TSO on vlan devices, tg3 needs to update
dev->vlan_features.
Tested on HP NC326m (aka BCM5715S (rev a3))
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now core network is able to handle 64 bit netdevice stats on 32 bit
arches, we can provide them for tg3, since hardware maintains 64 bit
counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.111.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5719 PCI device and phy IDs.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5719 ASIC revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver sometimes needs to know which function number the current
device is. This patch changes the code to use devfn over internal
register values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 serdes phy brings link up via parallel detection without any
additional help from the driver. This patch changes the
tg3_setup_fiber_mii_phy() function to detect and allow the use of this
feature.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code to make it legal to allocate only one MSI-X
vector. It also fixes a bug where the driver was not checking for error
return codes from pci_enable_msix().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was incorrectly programming the indirection table such that
rx traffic intended for the second ring went to the first ring, rx
traffic intended for the third ring went to the second ring, etc. This
patch changes the code so that rx traffic is diverted to the proper
ring.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx resources for MSI-X interrupt vector 0 were not being freed
correctly. This happens because the teardown loop continue's to the
next loop iteration if it detects the tx ring for that vector is not
setup, thus bypassing the rx teardown code. This patch moves the
call to tg3_rx_prodring_free() earlier in the loop.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain edge conditions, internal tx resources can get corrupted.
This patch enables a bit that will fix the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 and later devices relocate the APE mutex registers. This patch
organizes the code so that the driver can use the mutex registers in the
old and new locations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Fix INTx fallback when MSI fails
MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.
In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.
No functional change.
For further information about the background:
http://marc.info/?l=linux-netdev&m=127037540020276&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.110.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the following checkpatch errors:
* return is not a function, parentheses are not required
* space prohibited between function name and open parenthesis '('
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum packet size that gets programmed into the standard producer
ring control block is directly related to the packet size used to
allocate packet buffers. This patch removes the redundant preprocessor
constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver is written so that VLAN tagged packets can be accepted,
even if CONFIG_VLAN_8021Q or CONFIG_VLAN_8021Q_MODULE is not defined.
(Think raw interfaces.) If the device has ASF support enabled, the
firmware requires the driver to enable VLAN tag stripping. If VLAN
tagging is not explicitly supported by the kernel and ASF is enabled,
the driver will have to reinject the VLAN tag back into the packet
stream.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a PCIX bus, the 5701 has a bug which requires the driver to double
copy all rx packets. The rx code uses the rx_offset device member as a
flag to determine if this workaround should take effect. The following
patch will modify the rx_offset member such that this test will become
less clear.
The patch starts by integrating the workaround check into the packet
length check. It rounds out the implementation by relaxing the
workaround restrictions if the platform has efficient unaligned
accesses.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the core clock to 6.25MHz when operating at 10Mbps
link speed. This is needed to prevent a bug that will ultimately cause
transmits to cease.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the Maximum Read Request Size for the card reader
function to 1024 bytes to prevent an SD controller lockup.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables CLKREQ in L2 to workaround a chipset bug.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.109.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_dump_state() function is commented out and doesn't get used much
when debugging efforts are underway. The chip architecture has also
changed enough that any debugging effort that might use it would have to
tailor it to the capabilities of the hardware. This patch just removes
the function entirely.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the code style as it pertains to if statements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes checkpatch errors related to switch statements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes whitespace errors, preprocessor definition placement
oddities and updates comments.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extracts the firmware version from the VPD area and changes
the code to prefer that version version over the manually extracted
version.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that extracts the firmware version from the device's NVRAM
assumes the firmware version member is a clean slate. The following
patch will add code to extract the firmware version from the VPD area
of NVRAM, so this assumption will no longer be true. This patch adjusts
the versioning code to respect the VPD version if it exists.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05dbe00538, "Use (pr|netdev)_<level>
macro helpers" extended some of the message lines longer than 80 chars.
This patch reels the line lengths back in.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some uses of netdev_err() happen before the device has been registered.
This will cause the messages to be prepended with "(unregistered
net_device)" strings. We can clean up the message by using dev_err()
instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the instances of pr_err() in the tg3 driver have better
alternatives. This patch replaces all pr_err() calls.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating the new tg3_poll_msix() function, the likely() compiler
hint was dropped. This patch reintroduces it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The constant TG3_FLAG_10_100_ONLY should be used with the tg3_flags field,
not the tg3_flags2 field, as done elsewhere in the same file.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 09943a1819
Author: Matt Carlson <mcarlson@broadcom.com>
Date: Fri Aug 28 14:01:57 2009 +0000
tg3: Convert ISR parameter to tnapi
forgot to update tg3_poll_controller(), leading to intermittent crashes with
netpoll.
Fix this.
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD
information field header size and an inline function to extract the
size of the information field itself.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces more VPD preprocessor definitions to identify some
small and large resource data type item names. The patch then continues
to correct how the tg3 and bnx2 drivers search for the "read-only data"
large resource data type.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD large
resource data type tag size and an inline function to extract the large
resource section size from the large resource data type tag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Remove periods from most formats
Coalesce long formats
Use printk_once
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.108.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pushes phylib definitions out to phylib headers. For phy
IDs, this removes some code duplication.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylib presents the phy ID in a different format than the one tg3
has traditionally used. To highlight the distinction, this patch
prepends the tg3 native phy ID format with TG3.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reformats the SSID to phy ID table, replacing constants with
preprocessor definitions. This patch is also prep work for the
following patch, which will push line lengths beyond 80 chars.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy address will not change after it has been identified. Move the
discovery code to a location that only gets executed once.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an inverted "jumbo ring enable" test and jumps to the exit
if it succeeds. The change reduces the indent level of the remaining
code making it more readable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STD part of this preprocessor definition is a bit of a misnomer.
This flag is a coarse control of the RGMII inband status facilities.
This patch renames the definition to be more accurate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 57765 asic partno entries for the path executed if VPD
is not present in NVRAM.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch loosens the restriction that the phylib interface must be up
and running to change the flow control parameters.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new offsets to the bootcode version extraction code to
support NVRAM format versions 4 and 5.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 57791 and 57795 to the list of devices that only
support 10 and 100 Mbps speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan noted that there is nothing in the code that would prevent
the compiler from delaying the access of the "mapping" member of the
newly arrived packet until much later. If this happened after the
skb = NULL assignment, it is possible for the driver to pass a bad
dma_addr value to pci_unmap_single(). To enforce this ordering, we need
a write memory barrier. The pairing read memory barrier already exists
in tg3_rx_prodring_xfer() under the comments starting with
"Ensure that updates to the...".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AC131 does not enable the forced transmit clock settings
immediately. The workaround is to read the register again to get the
setting to take effect.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57765 lacks TSS support. This renders the napi assignments
incorrect in the loopback test function. This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver puts the phy into low-power mode when it releases the device.
If the device were to be reacquired, the phy needs a reset to bring it
back to full powered operation. This patch allows phylib-enabled
devices to reset the phy.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717's DMA read engine has a bug when initiating multiple DMA reads
across the PCIe bus. This patch disables the feature.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On A0 revision of 57765 asic rev devices, the bootcode will perform some
hardware operations, after the magic signature is presented, that will
collide with setup operations performed by the driver. The best way to
avoid the contention is to have the driver delay an additional 10
milliseconds. B0 revisions of the chip will make this workaround
unnecessary.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch changed the code so that new rx buffer submissions to
the hardware stall if a new submission would overwrite data needed by an
unserviced rx packet. On very busy 5717 and 57765 asic rev devices,
there is a corner case where the hardware will fail to assert an MSI-X
interrupt for rx traffic. If that vector's interrupt never has another
reason to assert, any rx buffers held will never be serviced. If the
buffers are never serviced and the hardware consumes all the available
rx packets for other rx rings, deadlock will result.
The most reliable and least intrusive way to work around the problem is
to detect the case where new submissions would overwrite existing data
and force all rx interrupt vectors to fire.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When operating in RSS mode, it is possible for one rx return ring to
submit enough rx buffers back to the hardware such that it inadvertently
overwrites data needed by another rx return ring. This patch addresses
the problem by looking for non-NULL skb pointers in the
rx_[std|jmb]_buffers rings that parallel the rx producer rings.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS ring 1 is responsible for submitting new rx buffers to the
hardware on behalf of all the other RSS rx return rings. Up until now
this ring submitted its new rx buffers to the producer ring directly.
The following patch will require that this ring have a place to put
backlogged rx packets. As a consequence, it can no longer submit new
buffers to the producer ring.
This patch adds code to allocate an extra shadow producer ring for this
RSS ring and adds RSS ring 1 to the list of rings needing buffer
transfers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rounds out the 57765 asic rev support by adding the 57765 phy
ID and entering the 57765 device IDs in the pci table.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57765 repurposes all the GPIOs normally used to switch power sources
when configured as a NIC device. This patch changes the code to avoid
touching the GPIOs for this asic rev.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the debug UART is left enabled, the LEDs will not work properly.
This patch disables the debug UART.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device supports MSI-X interrupts, the driver assumes TSS will be
available. This is not true for the 57765. This patch changes the code
so that only the default tx mailbox is initialized if TSS is not
available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57765 needs the driver to supply a nic address to the jumbo RCB,
just like all other devices except the 5717. This patch changes the
test to single out the 5717 rather than maintain a lengthy whitelist of
asic revs.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the 5717 and the 57765 will fail 'ethtool -t' selftests at the
memory selftest portion. The memory map for these two devices differs
from the rest of the asic revs and each other. This patch adds a new
memory map to use for memory selftests.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 serdes devices have a different phy register layout than all
other previous serdes devices. This patch aborts the phy init sequence
in tg3_phy_reset() if the device is a 5717 serdes. It also aborts the
tg3_phy_toggle_apd() operation. Most other operations in the MII_SERDES
path are O.K.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serdes and copper phys of the 5717 asic rev have different phy IDs.
This patch adds the serdes phy ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 and the 57765 have more resources at their disposal internally.
This patch tunes the driver to get better performance. The adjustments
made here only apply to the 57765 and 5717 asic revs.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIe PLL power down cannot be used if CLKREQ is enabled because data
corruption will occur. If CLKREQ is disabled though, enabling PCIE P1
PLL power-down saves some power.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the copyright notice for 2010 and updates the version
number to 3.106.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The B0 revision of the 5717 will not get enough testing by the time
2.6.33 ships. Since the kernel is already at RC3, serdes support
will require too many patches to fix. For these reasons, this patch
disables 5717 serdes support and will refuse to attach to all 5717
devices that are later than an A0 revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serdes status bit does not work as intended for the 5717 A0.
This patch implements an alternative detection scheme that will only be
valid for A0 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some tg3 devices that require the driver to post new rx
buffers in smaller increments. Commit
4361935afe, "tg3: Consider
rx_std_prod_idx a hw mailbox" changed how the driver tracks the rx
producer ring updates, but it does not make any special considerations
for the above-mentioned devices. For those devices, it is possible for
the driver to hit the special case path, which updates the hardware
mailbox register but skips updating the shadow software mailbox member.
If the special case path represents the final mailbox update for this
ISR iteration, the hardware and software mailbox values will be out of
sync. Ultimately, this will cause the driver to use a stale mailbox
value on the next iteration, which will appear to the hardware as a
large rx buffer update. Bad things ensue.
The fix is to update the software shadow mailbox member when the special
case path is taken.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 87668d352a, titled "tg3: Don't
touch RCB nic addresses", tried to avoid assigning the nic address of
the standard producer ring. Unfortunately, the default nic address is
not correct for the 5787, the 5755M, or the 57765. This patch
reenables the old behavior and opts out of the assignment only
for the 5717.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Tested-by: Chow Loong Jin <hyperair@ubuntu.com>
Tested-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.105.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3's firmware is no longer loaded from tg3_init_one(). Remove the
error path that releases the firmware back to the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver needs to use PCI configuration space to read the VPD data,
the accesses could collide with the pci_read_vpd() function. This patch
converts the driver to use pci_read_vpd() to avoid any potential
collisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the VPD code by creating preprocessor definitions
and using them in the place of hardcoded constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 57765 asic revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57765 asic rev has MSI-X capability, but does not support TSS. This
patch changes the tx paths so that TSS is explicitly mentioned, rather
than implied through the ENABLE_MSIX flag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
