The driver is tegra-i2s not just i2s. Rename the clocks to match, so that
clk_get_sys can look up by driver name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The following commit makes the Tegra APB DMA engine fail to initialize
correctly: 0cf6230af9
ARM: tegra: Move tegra_common_init to tegra_init_early
The reason is that tegra_init_early_ calls tegra_dma_init which calls
request_threaded_irq, which fails since the IRQ hasn't yet been marked
valid; that only happens in tegra_init_irq, which gets called after
tegra_init_early.
This used to work OK, since tegra_init_early was tegra_common_init, which
got called after tegra_init_irq, basically from the beginning of
tegra_harmony_init.
Solve this by converting tegra_dma_init to a postcore_initcall. This makes
it execute late enough that IRQs are marked valid, and avoids having to
add it back to every machine's init function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
This adds board support for the Seaboard eval platform and some of the
derivatives that are very similar. Since they only differ in some very
minor ways, most of the code is shared.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Turns out MMC2 (the bayonet 4-lane port) wasn't enabled in the
original pinmux. Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add the 3 sdhci devices that are available on Harmony as
platform devices. Two go to slots (one 4-lane, one 8-lane),
and one goes to onboard wifi.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add a common location to register resources for used on-chip devices
that are commonly configured on boards. Devices will be added to this file
as more drivers are added that can make use of them.
This is based on work contributed by several people, most of it from
Colin Cross and Erik Gilling.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Move harmony over to use the new gpio config table instead of having
separate settings in various parts of the code.
(The tegra sdhci driver should have the tegra_gpio_* ops removed, but
that will be done separately from this change.)
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
To give one place to setup the pins that are used as GPIOs instead
of as their pinmuxed functions. Specifying enabled as false explicitly
disables the gpio mode of that pin (if left on by firmware).
This should remove the need for calling these from specific drivers and
thus reduce tegra-specific code from them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
The option isn't terribly useful on other ARM platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Enable the cpu, emc (memory controller) and csite (debug and
trace controller) clocks during init to prevent them from
being disabled by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Enable the timer and rtc clocks to prevent them being
turned off by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Move tegra_common_init to tegra_init_early, and set it
as the init_early entry in the machine struct.
Initializes the clocks earlier so that timers can enable
their clocks.
Also reorders the members in the Harmony and Trimslice
boards' machine structs to match the order they are
called in.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Peripheral clocks that have no clock enable bit in the
enable registers have their clk_num set to 0. Bit 0
in the clock enable registers is the CPU clock.
Prevent disables on these peripheral clocks from
accidentally disabling the CPU clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Call the clock's round_rate op, if it exists, before calling
the set_rate op. This will help later when dvfs is added,
dvfs needs to know what the final rate will be before the
frequency changes.
Also requires fixes to the round rate functions to ensure
calling round rate and then set rate will not cause the
frequency to be rounded down twice. When picking clock
divider values, the clock framework picks the closest
frequency that is lower than the requested frequency. If
the new frequency calculated from the divider value is
rounded down, and then passed to set_rate, it will get
rounded down again, possibly resulting in a frequency two
steps lower than the original requested frequency.
Fix the problem by rounding up when calculating the frequency
coming out of a clock divider, so if that frequency is
requested again, the same divider value will be picked.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Some peripheral clocks share enable bits. Refcount the enables so
that calling clk_disable on one clock will not turn off another
clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Correct max rates for pclk and sclk (Originally fixed by
Dima Zavin <dima@android.com>)
Correct max rate for plla (Originally fixed by
Stephen Warren <swarren@nvidia.com>)
Remove unnecessary no-op set_rate on audio clocks
Add clock lookup entries for grhost, bsea, and vde clocks
Update clock clookup entries for vcp, bsea, and vde clocks
Add shared clock entries for sclk and emc
Add a virtual cop clock to provide a reset op (Originally fixed by
Dima Zavin <dima@android.com>)
Pass set_rate on super clocks through to parent
Fix pllx frequency table entry for 608 MHz
Remove incorrect plla frequency table entries
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The PLLP registers are now being restored by the low-level resume code,
and the CPU may be running off PLLP, so don't touch them during clock
resume.
Save plld, plls, pllu, and audio clock during suspend (originally
fixed by Mayuresh Kulkarni <mkulkarni@nvidia.com>)
The lock time for plld is 1000 us, so increase the delay after
setting the PLLs.
Add a BUG_ON to ensure the size of the suspend context area is
correct.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The SDMMC controllers have extra bits in the clock source
register that adjust the delay between the clock and data
to compenstate for delays on the PCB. The values need to
be set from the clock code so the clock can be locked
during the read-modify-write on the clock source register.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Adjusts the minimum memory frequency when the cpu frequency
changes. The values are currently hardcoded to a reasonable
default. If memory frequency scaling is not enabled this
patch will have no effect.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add clock ops on the emc peripheral clock that call into the
emc driver to update the memory controller registers for the
new frequency. Tegra has an interlock between the clock
controller and the memory controller that prevents the new
register values from taking effect until the clock frequency
update occurs.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The frequency memory bus on Tegra can be adjusted without
disabling accesses to memory by updating the memory
configuration registers from a per-board table, and then
changing the clock frequency. The clock controller and
memory controller have an interlock that prevents the
new memory registers from taking effect until the
clock frequency change.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Remove unnecessary uses of #ifdef CONFIG_DEBUG_FS
Convert bool assignments from 1 to true
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Some clocks may have multiple downstream users that need to request a
higher clock rate. Shared bus clocks provide a unique shared_bus_user
clock to each user. The frequency of the bus is set to the highest
enabled shared_bus_user clock, with a minimum value set by the
shared bus. Drivers can use clk_enable and clk_disable to enable
or disable their requirement, and clk_set_rate to set the minimum rate.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
During cpu frequency changes, take an extra reference to pllx so
that it doesn't turn off and on while the cpu is temporarily on
pllp. If the cpu is moved to pllp permanently, pllx will be
turned off.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Give each clock its own lock, and remove all lock traversals from
parent to child clocks to prevent AB-BA deadlocks.
This brings the locking in line with the common struct clk
patches and should make conversion simple.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Creates a union of a struct for each type of clock to reduce memory
usage and clarify which members are used by all clocks and which are
used by a single type.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Make the static clocks look more like the array of clocks
so they can all be initalized with the same helper function.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The existing version did not extend well to core dvfs, drop it
for now until the new clk api with clk_prepare and clk_unprepare
is ready and non-atomic clocks are possible.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The PLL lock bits are not reliable, use per-PLL timeouts instead.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Drop the unnecessary pr_debug calls to avoid having to maintain them.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
When updating the CPU PLL frequency, keeping the PLL enabled avoids
ramping the PLL all the way down and back up again. Remove the BUG_ON
in tegra2_pll_clk_set_rate to allow the rate to change while the PLL
is enabled.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add a new 'reset' clk op. This can be provided for any clock,
not just peripherals.
Signed-off-by: Dima Zavin <dima@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
This seems to be a regression in 2.6.37.
We cannot use writel() here since the resulting wmb() calls l2x0_cache_sync()
which uses a spinlock and L1 cache may be off at this point.
http://lists.infradead.org/pipermail/linux-arm-kernel/2011-February/041909.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Colin Cross <ccross@android.com>
If a request already in the queue is passed to tegra_dma_enqueue_req,
tegra_dma_req.node->{next,prev} will end up pointing to itself instead
of at tegra_dma_channel.list, which is the way a the end-of-list
should be set up. When the DMA request completes and is list_del'd,
the list head will still point at it, yet the node's next/prev will
contain the list poison values. When the next DMA request completes,
a kernel panic will occur when those poison values are dereferenced.
This makes the DMA driver more robust in the face of buggy clients.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Adding one single defconfig for the tegra family of boards, to over time
cover the superset of supported platform and drivers.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Sometimes, due to high interrupt latency in the continuous mode
of DMA transfer, the half buffer complete interrupt is handled
after DMA has transferred the full buffer. When this is detected,
stop DMA immediately and restart with the next buffer if the next
buffer is ready.
originally fixed by Victor(Weiguo) Pan <wpan@nvidia.com>
In place of using the simple spin_lock()/spi_unlock() in the
interrupt thread, using the spin_lock_irqsave() and
spin_unlock_irqrestore(). The lock is shared between the normal
process context and interrupt context.
originally fixed by Laxman Dewangan (ldewangan@nvidia.com)
The use of shadow registers caused memory corruption at physical
address 0 because the enable bit was not shadowed, and assuming it
needed to be set would enable an unconfigured dma block. Most of the
register accesses don't need to know the previous state of the
registers, and the few places that do need to modify only a few bits
in the registers are the same ones that were sometimes incorrectly
setting the enable bit. This patch convert tegra_dma_update_hardware
to set the entire register, and the other users to read-modify-write,
and drops the shadow registers completely.
Also fixes missing locking in tegra_dma_allocate_channel
Signed-off-by: Colin Cross <ccross@android.com>
On Tegra, calling clk_set_rate on the CPU clock may call into the
regulator API. If the regulator driver that controls the CPU
voltage rail has been suspended, this can lead to attempted
communication with a hardware block that has already been turned
off.
Adds a SUSPEND_PREPARE notification hook to drop the frequency to
the lowest possible during suspend.
Also adds 216MHz (off of PLLP) as the lowest CPU frequency, which
allows PLLX to be turned off.
Signed-off-by: Colin Cross <ccross@android.com>
Adds gart, hdmi, avp, host1x, and pwm controllers to mach/iomap.h
Signed-off-by: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Implement read_persistent_clock by reading the Tegra RTC
registers that stay running during suspend.
Save and restore the timer configuration register in
suspend.
Signed-off-by: Colin Cross <ccross@android.com>
