Allow to compile it if AT91 is enable.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make the ECHI depends on ARCH_AT91
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: devicetree-discuss@lists.ozlabs.org
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
Add PID 0x6015, corresponding to the new series of FT-X chips
(FT220XD, FT201X, FT220X, FT221X, FT230X, FT231X, FT240X). They all
appear as serial devices, and seem indistinguishable except for the
default product string stored in their EEPROM. The baudrate
generation matches FT232RL devices.
Tested with a FT201X and FT230X at various baudrates (100 - 3000000).
Sample dmesg:
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
usb 2-1: new full-speed USB device number 6 using ohci_hcd
usb 2-1: New USB device found, idVendor=0403, idProduct=6015
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: Product: FT230X USB Half UART
usb 2-1: Manufacturer: FTDI
usb 2-1: SerialNumber: DC001WI6
ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected
drivers/usb/serial/ftdi_sio.c: ftdi_sio_port_probe
drivers/usb/serial/ftdi_sio.c: ftdi_determine_type: bcdDevice = 0x1000, bNumInterfaces = 1
usb 2-1: Detected FT-X
usb 2-1: Number of endpoints 2
usb 2-1: Endpoint 1 MaxPacketSize 64
usb 2-1: Endpoint 2 MaxPacketSize 64
usb 2-1: Setting MaxPacketSize 64
drivers/usb/serial/ftdi_sio.c: read_latency_timer
drivers/usb/serial/ftdi_sio.c: write_latency_timer: setting latency timer = 1
drivers/usb/serial/ftdi_sio.c: create_sysfs_attrs
drivers/usb/serial/ftdi_sio.c: sysfs attributes for FT-X
usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0
Signed-off-by: Jim Paris <jim@jtan.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A MCS7820 device supports two serial ports and a MCS7840 device supports
four serial ports. Both devices use the same driver, but the attach function
in driver was unable to correctly handle the port numbers for MCS7820
device. This problem has been fixed in this patch and this fix has been
verified on x86 Linux kernel 3.2.9 with both MCS7820 and MCS7840 devices.
Signed-off-by: Donald Lee <donald@asix.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fact that an architecture/board has XHCI, OHCI or EHCI does not
depend on the fact that the kernel is configured with USB_SUPPORT.
Make the Kconfig reflect this fact thus avoiding ugly messages like:
warning: (MIPS_ALCHEMY && CAVIUM_OCTEON_REFERENCE_BOARD && SOC_AR71XX && SOC_AR724X && SOC_AR913X && SOC_AR933X) selects USB_ARCH_HAS_EHCI which has unmet direct dependencies (USB_SUPPORT)
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28824b18ac:
|Author: Michal Nazarewicz <m.nazarewicz@samsung.com>
|Date: Wed May 5 12:53:13 2010 +0200
|
| USB: gadget: __init and __exit tags removed
|
| __init, __initdata and __exit tags have have been removed from
| various files to make it possible for gadgets that do not use
| the __init/__exit tags to use those.
obviously missed (at least) this case leading to a section mismatch in
g_ffs.c when compiling with CONFIG_USB_FUNCTIONFS_ETH enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the re-coded i2c_write function from the ohci-nxp driver
in favour of using just smbus functions.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the LPC32xx to ohci-nxp
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this driver is compatible with several NXP devices, the driver was renamed
accordingly. This patch also changes the respective symbol names.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this driver is compatible with several NXP devices, the driver is renamed
accordingly. Please combine with the following patch which also changes the
respective symbol names.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When applying commit 7d26b58 (fix failure path in
dwc3_pci_probe()), I mistakenly left out one of the
possible failures where we would return success even
on the error case.
This patch fixes that mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Non-hub device has no child, and even a real USB hub has ports far
less than USB_MAXCHILDREN, so there is no need using a fix array for
child devices, just allocate it dynamically according real port
number.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Update sg tablesize as we can expand the ring now.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
When a urb is submitted to xHCI driver, check if queueing the urb will make
the enqueue pointer advance into dequeue seg and expand the ring if it
occurs. This is to guarantee the safety of ring expansion.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Allocate 2 segments for transfer ring by default, so we can expand the ring
when the enqueue pointer and dequeue pointer are in different segments.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
If room_on_ring() check fails, try to expand the ring and check again.
When expand a ring, use a cached ring or allocate new segments, link
the original ring and the new ring or segments, update the original ring's
segment numbers and the last segment pointer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
In the past all the rings were allocated with cycle state equal to 1.
Now the driver may expand an existing ring, and the new segments shall be
allocated with the same cycle state as the old one.
This affects ring allocation and cached ring re-initialization.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Factor out the segments allocation and free part from ring allocation
and free routines since driver may call them directly when try to expand
a ring.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
In the past, the room_on_ring() check was implemented by walking all over
the ring, which is wasteful and complicated.
Count the number of free TRBs instead. The free TRBs number should be
updated when enqueue/dequeue pointer is updated, or upon the completion
of a set dequeue pointer command.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Store the ring's last segment pointer and number of segments for ring
expansion usage.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
When allocate a ring, store its type - four transfer types for endpoint,
TYPE_STREAM for stream transfer, and TYPE_COMMAND/TYPE_EVENT for xHCI host.
This helps to get rid of three bool function parameters: link_trbs, isoc
and consumer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
__ffs() can tell us which is the SEGMENT_SHIFT value
to be used. This will prevent problems when users are
too fast and don't pay attention to the need of fixing
the Shift after changing TRBS_PER_SEGMENT.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The latest released errata for USB2.0 ECN LPM adds new fields to USB2.0
extension descriptor, defines two BESL values for device: baseline BESL
and deep BESL. Baseline BESL value communicates a nominal power savings
design point and the deep BESL value communicates a significant power
savings design point.
If device indicates BESL value, driver will use a value count in both
host BESL and device BESL. Use baseline BESL value as default.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Tested-by: Jason Fan <jcfan@qca.qualcomm.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This properly ties the driver into the dynamic debug system and provides
the needed device identification when the messages are printed out.
It also removes a ton of checkpatch warnings as well, which is always a
nice validation that it's the correct thing to do.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should use kzalloc() instead of kmalloc() and memset(), and remove an
unneeded void * cast as well.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They aren't needed, make the checkpatch tool unhappy, and in some
places, aren't even correct. So just remove them, they get in the way
and are messy.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By rearranging the functions a bit, we can remove all function
prototypes.
Note, this also deleted the _close function, as it wasn't needed, it was
doing the same thing the cleanup function did, so just call that
instead.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up all of the coding style errors, and removes the initial,
unneeded comments on how to load the module and the old changelog which
are no longer needed.
There are still a number of coding style warnings left, I'll get to them
later.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A driver doesn't need a .h file just for simple things like vendor ids
and a private structure. So move it into the .c file instead, saving
some overall lines.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we aren't doing anything special in the init function, move to
use the easier module_usb_serial_driver() call instead, saving a lot of
lines of unnecessary code.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All new usb serial drivers should be using the dynamic id function, not
having module parameters for this type of thing. So remove them before
anyone gets used to them being there.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the metro-usb driver to the build system properly.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb serial core has changed how the driver is to be registered and
unregistered recently. Make these changes to the driver so that it will
properly build and work.
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HID devices should specify this in their interface descriptors, not in the
device descriptor. This fixes a "missing hardware id" bug under Windows 7 with
a VIA VL800 (3.0) controller.
Signed-off-by: Orjan Friberg <of@flatfrog.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver can be used as a subdriver of another USB driver, allowing
it to export a Device Managment interface consisting of a single interrupt
endpoint with no dedicated USB interface.
Some devices provide a Device Management function combined with a wwan
function in a single USB interface having three endpoints (bulk in/out
+ interrupt). If the interrupt endpoint is used exclusively for DM
notifications, then this driver can support that as a subdriver
provided that the wwan driver calls the appropriate entry points on
probe, suspend, resume, pre_reset, post_reset and disconnect.
The main driver must have full control over all interface related
settings, including the needs_remote_wakeup flag. A manage_power
function must be provided by the main driver.
A manage_power stub doing direct flag manipulation is used in normal
driver mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register all interfaces handled by this driver in a list, getting
rid of the dependency on usb_set_intfdata. This allows further
generalization and simplification of the probe/create functions.
This is needed to decouple wdm_open from the driver owning the
interface, and it also allows us to share all the code in
wdm_create with drivers unable to do usb_set_intfdata.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparing for the addition of subdriver registering as an alternative
to probe for interface-less usage. This should not change anything
apart from minor code reordering.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Microchip VID (0x04d8) was mislabeled as Hornby VID according to USB-IDs.
A Full Speed USB Demo Board PID (0x000a) was mislabeled as
Hornby Elite (an Digital Command Controller Console for model railways).
Most likely the Hornby based their design on
PIC18F87J50 Full Speed USB Demo Board.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA burst support is added to improve performance in EHCI data
transfer. The USB EHCI controller on Exynos SoCs can use INCR16,
INCR8, and INCR4 mode. These modes of INSNREG00 register should
be set in order to enable DMA burst transfer. This feature is
also related to AHB spec.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking if tty->index is in bounds is not needed. The tty has the
index set in the initial open. This is done in get_tty_driver. And it
can be only in interval <0,driver->num).
So remove the tests which check exactly this interval. Some are
left untouched as they check against the current backing device count.
(Leaving apart that the check is racy in most of the cases.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a piece I missed the last time.
Do not copy the functionality all over the tree. Instead, use the
helper the tty layer provides us with.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe() function will always fail because we're testing the wrong
variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A read from GadgetFS endpoint 0 during the data stage of a control
request would always return 0 on success (as returned by
wait_event_interruptible) despite having written data into the user
buffer.
This patch makes it correctly set the return value to the number of
bytes read.
Signed-off-by: Thomas Faber <thfabba@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel doc entry for usb_unlink_urb() contains the phrase "This
request is always asynchronous.". The "always" leads to the assumption
that the ->complete() callback is not called from within
usb_unlink_urb(). This is not true. The HCD is allowed to call the
->complete() from within ->urb_dequeue() if it is appropriate for the
hardware.
This patch updates the kernel doc so usb-device driver authors make sure
to drop all locks (and make sure it is okay to drop them) which are
acquired by the complete callback before calling usb_unlink_urb().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the coverity checker puts it:
"Passing argument "sizeof (midi_function) /*8*/" to function "kcalloc"
and then casting the return value to "struct usb_descriptor_header **"
is suspicious. ... In this particular case sizeof(struct
usb_descriptor_header **) happens to be equal to sizeof(struct
usb_descriptor_header *), but this is not a portable assumption."
I believe we really do intend to use 'sizeof(*midi_function)' here, so
this patch makes that change.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"len" is unsigned so it's never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the cp210x driver to support CP210x multiple
interface devices devices from Silicon Labs. The existing driver
always sends control requests to interface 0, which is hardcoded in
the usb_control_msg function calls. This only allows for single
interface devices to be used, and causes a bug when using ports on an
interface other than 0 in the multiple interface devices.
Here are the changes included in this patch:
- Updated the device list to contain the Silicon Labs factory default
VID/PID for multiple interface CP210x devices
- Created a cp210x_port_private struct created for each port on
startup, this struct holds the interface number
- Added a cp210x_release function to clean up the cp210x_port_private
memory created on startup
- Modified usb_get_config and usb_set_config to get a pointer to the
cp210x_port_private struct, and use the interface number there in the
usb_control_message wIndex param
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 529febeee6.
To quote Dirk:
This commit introduces a check for the USB PHY clock.
Problem is that CTRL_PHY_CLK_VALID bit seems not to be present
on all Freescale ehci implementations, at least P1022 does not
have it. So this check always fails and the driver never gets
loaded.
So we need to revert this patch.
Reported-by: Dirk Eibach <Eibach@gdsys.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Z2+
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: changes for v3.4 merge window
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
Conflicts:
drivers/usb/dwc3/gadget.c
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
ARM: at91/tclib: take iomem size from resource
ARM: at91/pit: add traces in case of error
ARM: at91: pit add DT support
ARM: at91: AIC and GPIO IRQ device tree initialization
ARM: at91/board-dt: remove AIC irq domain from board file
ARM: at91/gpio: remove the static specification of gpio_chip.base
ARM: at91/gpio: add .to_irq gpio_chip handler
ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node field
ARM: at91/gpio: add irqdomain and DT support
ARM: at91/gpio: change comments and one variable name
ARM/USB: at91/ohci-at91: remove the use of irq_to_gpio
...
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.
Conflicts:
drivers/rtc/rtc-at91sam9.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Transfer resource index is cleared in hardware when XFERCOMPLETE
event is generated, so clear the driver's res_trans_idx variable
immediately after that event is received. The upcoming hibernation
patches depend on this change.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep_set_wedge() and dwc3_gadget_set_selfpowered() were
modifying dwc->flags/dwc->is_selfpowered without taking the lock.
Since those modifications are non-atomic, that could cause other
flags to be corrupted. Fix them both to take the lock.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The loop in dwc3_gadget_set_link_state() was using a udelay(500),
which is a long time to delay in interrupt context. Change it to
udelay(5) and increase the loop count to match.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_pci_probe() would return success even if the calls to
dwc3_get_device_id() or platform_device_alloc() fail, fix that.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Define DWC3_GCTL_SCALEDOWN_MASK and use it in place of
DWC3_GCTL_SCALEDOWN(3).
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Zero is a valid value for a microframe number. So remove the bogus
test for non-zero in dwc3_gadget_start_isoc().
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's wrong to use the size of array as an argument for strncat.
Memory corruption is possible. strlcat is exactly what we need here.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we have a non-ISOC endpoint, we will not have a Link TRB
pointing to the beginning of the TRB pool. On such endpoints,
we don't want to let the driver wrap around the TRB pool
otherwise controller will hang waiting for a valid TRB.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We always return zero instead of the id we found.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/dwc3/core.c and drivers/usb/dwc3/dwc3-omap.c
included 'linux/module.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch enables to use devm_xxx functions during probing driver.
The devm_xxx series functions are able to release resource when the
driver is detatched. We can remove several codes to release resources
in the probe function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds Exynos Specific Glue layer to support USB peripherals
on Samsung Exynos5 chips.
[ balbi@ti.com : prevent compilation of Exynos glue layer
on platforms which don't provide clk API implementation ]
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BeagleBone changed to the default FTDI 0403:6010 id in rev A5 to make life
easier for Windows users, so we need a similar workaround as the Calao
board to support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RR+f
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: Gadget: changes for 3.4
This merge is rather big. Here's what it contains:
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
Conflicts:
drivers/usb/dwc3/gadget.c
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
a patch making modules behave better, there's a fix on debugfs'
error path, a small change removing an unnecessary pm_runtime
call on musb_shutdown() and a fix to relesect the endpoint in
Interrupt context.
This last patch is needed because we must drop musb's lock when
calling request->complete() and that could cause problems if another
thread queues a request and ends up changing MUSB_INDEX register.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2VXE
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: MUSB changes for 3.4
Here are a set of changes to the MUSB driver. In summary we have
a patch making modules behave better, there's a fix on debugfs'
error path, a small change removing an unnecessary pm_runtime
call on musb_shutdown() and a fix to relesect the endpoint in
Interrupt context.
This last patch is needed because we must drop musb's lock when
calling request->complete() and that could cause problems if another
thread queues a request and ends up changing MUSB_INDEX register.
irq_to_gpio() macro will be removed from AT91 GPIO interrupt
controller. So we replace it with the use of gpio_to_irq()
and a reworked test.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-usb@vger.kernel.org
This reverts commit 79857e8e7b.
To quote Shengzhou Liu:
I'm sorry, please don't apply this patch.
It appears not only on P1022 platform.
There will be more breaks on other platforms regarding
CTRL_PHY_CLK_VALID bit.
I will post a new patch with well compatibility on all
platforms as soon as I get necessary confirmations.
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the first cut at a driver for the Fintek F81232 USB to serial
single port converter. This provides the initial framework for the
device, and some data can move through it, but no line settings are
handled, so it's not that useful yet. It does give people a starting
place to work from.
Thank to Fintek for providing samples and specifications, without which,
this driver would have never been able to be written.
Cc: Amanda Ying <Amanda_Ying@fintek.com.tw>
Cc: Tom Tsai <Tom_Tsai@fintek.com.tw>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the zio.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the whiteheat.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the vivopay-serial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the usb_debug.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the symbolserial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the ssu100.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the spcp8x5.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
