Validate the VPD checksum with pci_vpd_check_csum() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
str_id_reg and str_id_cap hold the same string and are used in the same
comparison. This doesn't make sense, use one string str_id instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same as 37838aa437 "sfc: Search VPD with
pci_vpd_find_ro_info_keyword()", just for the falcon chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same as 5119e20fac "sfc: Read VPD with pci_vpd_alloc()",
just for the falcon chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Refactor parsing configuration
The Spectrum ASIC has a configurable limit on how deep into the packet
it parses. By default, the limit is 96 bytes.
There are several cases where this parsing depth is not enough and there
is a need to increase it: Decapsulation of VxLAN packets and
timestamping of PTP packets.
Currently, parsing depth API is maintained as part of VxLAN module,
because the MPRS register which configures parsing depth also configures
UDP destination port number used for VxLAN encapsulation and
decapsulation.
However, in addition to two above mentioned users of this API, the
multipath hash code also needs to invoke it in order to correctly hash
based on inner fields of IPv6-in-IPv6 packets.
Upcoming support for IPv6-in-IPv6 tunneling will add another user, as
without increasing the parsing depth such packets cannot be properly
decapsulated.
Therefore, this patchset refactors the parsing configuration API and
moves it out of the VxLAN module to the main driver code.
Tested using existing selftests.
Patch set overview:
Patch #1 adds the new parsing configuration infrastructure.
Patch #2 converts existing users to the new infrastructure.
Patch #3 deletes the old infrastructure.
Patch #4 calls the new infrastructure from the multipath hash code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 01848e05f8 ("mlxsw: spectrum_router: Add support for inner
layer 3 multipath hash policy") and commit daeabf89eb ("mlxsw:
spectrum_router: Add support for custom multipath hash policy") added
support for multipath hash policies where the hash is calculated based
on inner packet fields.
For IPv6-in-IPv6 packets, the default parsing depth (96 bytes) is not
enough when these policies are used.
Therefore, for such cases, call the new API to increase / decrease the
parsing depth as necessary. Care is taken to ensure the API is not
called multiple times.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches added new API to handle parsing depth and converted
the existing code to use it.
Remove the old infrastructure which is not needed anymore.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert VxLAN and PTP modules to increase parsing depth using new API
that was added in the previous patch.
Separate MPRS register's configuration to VxLAN related configuration
and parsing depth configuration. Handle each one using the appropriate
API.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum ASICs have a configurable limit on how deep into the packet
they parse. By default, the limit is 96 bytes.
There are several cases where this parsing depth is not enough and there
is a need to increase it. Currently, increasing parsing depth is
maintained as part of VxLAN module, because the MPRS register which
configures parsing depth also configures UDP destination port number
used for VxLAN encapsulation and decapsulation.
Add an API for increasing parsing depth as part of spectrum.c code, so
that it will be possible to use it from other modules. In addition, add
an API for setting UDP destination port and protect it using a dedicated
lock for saving parsing configurations. The lock is needed as not all
the callers hold RTNL lock.
Maintain a counter for increased parsing depth consumers. For first
consumer subscription, increase the parsing depth and for last consumer
unsubscription, set parsing depth to default value.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham says:
====================
octeontx2: Miscellaneous fixes
This patch series contains a bunch of miscellaneous fixes
for various issues like
- Free unallocated memory during driver unload
- HW reading transmit descriptor from wrong address
- VF VLAN strip offload MCAM entry installation failure
- Pkts not being distributed across queues in RSS context
- Wrong interface backpressure configuration for NIX1 block on 98xx
- etc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RVU SMMU widget stores the final translated PA at
RVU_AF_SMMU_TLN_FLIT0<57:18> instead of FLIT1 register. This patch
fixes the address translation logic to use the correct register.
Fixes: 893ae97214 ("octeontx2-af: cn10k: Support configurable LMTST regions")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherthan setting action as RSS in NPC MCAM entry, RSS flowkey
algorithm index also needs to be set. Otherwise whatever algorithm
is defined at flowkey index '0' will be considered by HW and pkt
flows will be distributed as such.
Fix this by saving the flowkey index sent by admin function while
initializing RSS and then use it when framing MCAM rules.
Fixes: 81a4362016 ("octeontx2-pf: Add RSS multi group support")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever user changes interface MAC address both default DMAC based
MCAM rule and VLAN offload (for strip) rules are updated with new
MAC address. To update or install VLAN offload rule PF driver needs
interface's receive channel info, which is retrieved from admin
function at the time of NIXLF initialization.
If user changes MAC address before interface is UP, VLAN offload rule
installation will fail and throw error as receive channel is not valid.
To avoid this, skip VLAN offload rule installation if netdev is not UP.
This rule will anyway be reinslatted as part of open() call.
Fixes: fd9d7859db ("octeontx2-pf: Implement ingress/egress VLAN offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bandwidth profiles (ipolicer structure)is implemented only on CN10K
platform. But current code try to free the ipolicer memory without
checking the capibility flag leading to driver crash on OCTEONTX2
platform. This patch fixes the issue by add capability flag check.
Fixes: e8e095b3b3 ("octeontx2-af: cn10k: Bandwidth profiles config support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K platform requires physically contiguous memory for LMTST
operations which goes beyond a single page. Not having physically
contiguous memory will result in HW fetching transmit descriptors from
a wrong memory location.
Hence use DMA_ATTR_FORCE_CONTIGUOUS attribute while allocating
LMTST regions.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the erroneous vlan priority mask field that was
send to npc_install_flow_req.
Fixes: 1d4d9e42c2 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported link modes are updated by firmware in shared
structure per interface. Kernel uses this value to display
supported link modes via ethtool.
Currently there is extra validation that firmware updated
modes are validated against internal list of supported modes.
As intenal list of supported modes are not updated frequently
new modes supported by firmware are not updated to ethtool.
Hence remove extra validation and report all firmware updated
modes.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print debug message if any of the RVU hardware blocks
reset fails.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per hardware the base channel number configured
for programmable channels of a block must be multiple
of number of channels of that block. This condition
is not met for SDP base channel currently. Hence this
patch ensures all the base channel numbers of all
blocks are multiple of number of channels present in
the blocks. Also instead of hardcoding SDP number
of channels the same is read from the NIX_AF_CONST1
register.
Fixes: 242da43921 ("octeontx2-af: cn10k: Add support for programmable")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'bp_ena' in Aura context is NIX block index, setting it
zero will always backpressure NIX0 block, even if NIXLF
belongs to NIX1. Hence fix this by setting it appropriately
based on NIX block address.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
DSA documentation updates for v5.15
There were some documentation-visible changes made to DSA in the
net-next tree for v5.15. There may be more, but these are the ones I am
aware of.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new methods have been introduced, add some verbiage about what they do.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has disappeared in commit edac6f6332 ("Revert "net: dsa:
Allow drivers to filter packets they can decode source port from"").
Also, since commit 4e50025129 ("net: dsa: generalize overhead for
taggers that use both headers and trailers"), the next paragraph is no
longer true (it is still discouraged to do that, but it is now
supported, so no point in mentioning it). Delete.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the paragraphs that talk about the various modes of traffic
support, bridging with foreign interfaces, etc etc. There is nothing
that the user needs to know now, it should all work out of the box as
expected.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has removed its devlink params, so there is nothing
to see here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: enable automatic suspend
At long last, the first patch in this series enables automatic
suspend managed by the power management core. The remaining two
just rename things to be "power" oriented rather than "clock"
oriented.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, rename "ipa_clock.c" to be "ipa_power.c" and "ipa_clock.h"
to be "ipa_power.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename a number of functions to clarify that there is no longer a
notion of an "IPA clock," but rather that the functions are more
generally related to IPA power management.
ipa_clock_enable() -> ipa_power_enable()
ipa_clock_disable() -> ipa_power_disable()
ipa_clock_rate() -> ipa_core_clock_rate()
ipa_clock_init() -> ipa_power_init()
ipa_clock_exit() -> ipa_power_exit()
Rename the ipa_clock structure to be ipa_power. Rename all
variables and fields using that structure type "power" rather
than "clock".
Rename the ipa_clock_data structure to be ipa_power_data, and more
broadly, just substitute "power" for "clock" in places that
previously represented things related to the "IPA clock".
Update comments throughout.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use runtime power management autosuspend.
Up until this point, we only suspended the IPA hardware for system
suspend; now we'll suspend it aggressively using runtime power
management, setting the initial autosuspend delay to half a second
of inactivity.
Replace pm_runtime_put() calls with pm_runtime_put_autosuspend(),
call pm_runtime_mark_last_busy() before each of those. In places
where we're shutting things down, or decrementing power references
for errors, use pm_runtime_put_noidle() instead.
Finally, remove ipa_runtime_idle(), so the ->runtime_suspend
callback will occur if idle.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* BSS coloring support
* MEI commands for Intel platforms
* various fixes/cleanups
-----BEGIN PGP SIGNATURE-----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=q8bL
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-08-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Minor updates:
* BSS coloring support
* MEI commands for Intel platforms
* various fixes/cleanups
* tag 'mac80211-next-for-net-next-2021-08-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
cfg80211: fix BSS color notify trace enum confusion
mac80211: Fix insufficient headroom issue for AMSDU
mac80211: add support for BSS color change
nl80211: add support for BSS coloring
mac80211: Use flex-array for radiotap header bitmap
mac80211: radiotap: Use BIT() instead of shifts
mac80211: Remove unnecessary variable and label
mac80211: include <linux/rbtree.h>
mac80211: Fix monitor MTU limit so that A-MSDUs get through
mac80211: remove unnecessary NULL check in ieee80211_register_hw()
mac80211: Reject zero MAC address in sta_info_insert_check()
nl80211: vendor-cmd: add Intel vendor commands for iwlmei usage
====================
Link: https://lore.kernel.org/r/20210820105329.48674-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov says:
====================
net: bridge: mcast: add support for port/vlan router control
This small set adds control over port/vlan mcast router config.
Initially I had added host vlan entry router control via vlan's global
options but that is really unnecessary and we can use a single per-vlan
option to control it both for port/vlan and host/vlan entries. Since
it's all still in net-next we can convert BRIDGE_VLANDB_GOPTS_MCAST_ROUTER
to BRIDGE_VLANDB_ENTRY_MCAST_ROUTER and use it for both. That makes much
more sense and is easier for user-space. Patch 01 prepares the port
router function to be used with port mcast context instead of port and
then patch 02 converts the global vlan mcast router option to per-vlan
mcast router option which directly gives us both host/vlan and port/vlan
mcast router control without any additional changes.
This way we get the following coherent syntax:
[ port/vlan mcast router]
$ bridge vlan set vid 100 dev ens20 mcast_router 2
[ bridge/vlan mcast router ]
$ bridge vlan set vid 100 dev bridge mcast_router 2
instead of:
$ bridge vlan set vid 100 dev bridge mcast_router 1 global
The mcast_router should not be regarded as a global option, it controls
the port/vlan and bridge/vlan mcast router behaviour.
This is the last set needed for the initial per-vlan mcast support.
Next patch-sets:
- iproute2 support
- selftests
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-vlan router option controls the port/vlan and host vlan entries'
mcast router config. The global option controlled only the host vlan
config, but that is unnecessary and incosistent as it's not really a
global vlan option, but rather bridge option to control host router
config, so convert BRIDGE_VLANDB_GOPTS_MCAST_ROUTER to
BRIDGE_VLANDB_ENTRY_MCAST_ROUTER which can be used to control both host
vlan and port vlan mcast router config.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change br_multicast_set_port_router to take port multicast context as
its first argument so we can later use it to control port/vlan mcast
router option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that mcam flows are allocated
before adding or destroying the flows.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This silences the following coccinelle warning:
"WARNING: sum of probable bitmasks, consider |"
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: jing yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: kill off ipa_clock_get()
This series replaces the remaining uses of ipa_clock_get() with
calls to pm_runtime_get_sync() instead. It replaces all calls to
ipa_clock_put() with calls to pm_runtime_put().
This completes the preparation for enabling automated suspend under
the control of the power management core code. The next patch (in
an upcoming series) enables that. Then the "ipa_clock" files and
symbols will switch to using an "ipa_power" naming convention instead.
Additional info
It is possible for pm_runtime_get_sync() to return an error. There
are really three cases, identified by return value:
- 1, meaning power was already active
- 0, meaning power was not previously active, but is now
- EACCES, meaning runtime PM is disabled
One additional case is EINVAL, meaning a previous suspend or resume
(or idle) call returned an error. But we have always assumed this
won't happen (we previously didn't even check for an error).
But because we use pm_runtime_force_suspend() to implement system
suspend, there's a chance we'd get an EACCES error (the first thing
that function does is disable runtime suspend). Individual patches
explain what happens in that case, but generally we just accept that
it could be an unlikely problem (occurring only at startup time).
Similarly, pm_runtime_put() could return an error. There too, we
ignore EINVAL, assuming the IPA suspend and resume operations won't
produce an error. EBUSY and EPERM are not applicable, EAGAIN is not
expected (and harmless). We should never get EACCES (runtime
suspend disabled), because pm_runtime_put() calls match prior
pm_runtime_get_sync() calls, and a system suspend will not be
started while a runtime suspend or resume is underway. In summary,
the value returned from pm_runtime_put() is not meaningful, so we
explicitly ignore it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining user of the ipa_clock_{get,put}() interface is
ipa_isr_thread(). Replace calls to ipa_clock_get() there calling
pm_runtime_get_sync() instead. And call pm_runtime_put() there
rather than ipa_clock_put(). Warn if we ever get an error.
With that, we can get rid of ipa_clock_get() and ipa_clock_put().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we open or close the modem network device we need to ensure the
hardware is powered. Replace the callers of ipa_clock_get() found
in ipa_open() and ipa_stop() with calls to pm_runtime_get_sync().
If an error is returned, simply return that error to the caller
(without any error or warning message). This could conceivably
occur if the function was called while the system was suspended,
but that really shouldn't happen. Replace corresponding calls to
ipa_clock_put() with pm_runtime_put() also.
If the modem crashes we also need to ensure the hardware is powered
to recover. If getting power returns an error there's not much we
can do, but at least report the error. (Ideally the remoteproc SSR
code would ensure the AP was not suspended when it sends the
notification, but that is not (yet) the case.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the ipa_clock_get() call in ipa_uc_clock() when taking the
"proxy" clock reference for the microcontroller with a call to
pm_runtime_get_sync(). Replace calls of ipa_clock_put() for the
microcontroller with pm_runtime_put() calls instead.
There is a chance we get an error when taking the microcontroller
power reference. This is an unlikely scenario, where system suspend
is initiated just before we learn the modem is booting. For now
we'll just accept that this could occur, and report it if it does.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the "modem-init" Device Tree property is present for a platform,
the modem performs early IPA hardware initialization, and signals
this is complete with an "ipa-setup-ready" SMP2P interrupt. This
triggers a call to ipa_setup(), which requires the hardware to be
powered.
Replace the call to ipa_clock_get() in this case with a call to
pm_runtime_get_sync(). And replace the corresponding calls to
ipa_clock_put() with calls to pm_runtime_put() instead.
There is a chance we get an error when taking this power reference.
This is an unlikely scenario, where system suspend is initiated just
before the modem signals it has finished initializing the IPA
hardware. For now we'll just accept that this could occur, and
report it if it does.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the hardware to be powered starting at the config stage of
initialization when the IPA driver probes. And we need it powered
when the driver is removed, at least until the deconfig stage has
completed.
Replace callers of ipa_clock_get() in ipa_probe() and ipa_exit(),
calling pm_runtime_get_sync() instead. Replace the corresponding
callers of ipa_clock_put(), calling pm_runtime_put() instead.
The only error we expect when getting power would occur when the
system is suspended. The ->probe and ->remove driver callbacks
won't be called when suspended, so issue a WARN() call if an error
is seen getting power.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski pointed out a race condition in ipa_start_xmit() in a
recently-accepted series of patches:
https://lore.kernel.org/netdev/20210812195035.2816276-1-elder@linaro.org/
We are stopping the modem TX queue in that function if the power
state is not active. We restart the TX queue again once hardware
resume is complete.
TX path Power Management
------- ----------------
pm_runtime_get(); no power Start resume
Stop TX queue ...
pm_runtime_put() Resume complete
return NETDEV_TX_BUSY Start TX queue
pm_runtime_get()
Power present, transmit
pm_runtime_put() (auto-suspend)
The issue is that the power management (resume) activity and the
network transmit activity can occur concurrently, and there's a
chance the queue will be stopped *after* it has been started again.
TX path Power Management
------- ----------------
Resume underway
pm_runtime_get(); no power ...
Resume complete
Start TX queue
Stop TX queue <-- No more transmits after this
pm_runtime_put()
return NETDEV_TX_BUSY
We address this using a STARTED flag to indicate when the TX queue
has been started from the resume path, and a spinlock to make the
flag and queue updates happen atomically.
TX path Power Management
------- ----------------
Resume underway
pm_runtime_get(); no power Resume complete
start TX queue \
If STARTED flag is *not* set: > atomic
Stop TX queue set STARTED flag /
pm_runtime_put()
return NETDEV_TX_BUSY
A second flag is used to address a different race that involves
another path requesting power.
TX path Other path Power Management
------- ---------- ----------------
pm_runtime_get_sync() Resume
Start TX queue \ atomic
Set STARTED flag /
(do its thing)
pm_runtime_put()
(auto-suspend)
pm_runtime_get() Mark delayed resume
STARTED *is* set, so
do *not* stop TX queue <-- Queue should be stopped here
pm_runtime_put()
return NETDEV_TX_BUSY Suspend done, resume
Resume complete
pm_runtime_get()
Stop TX queue
(STARTED is *not* set) Start TX queue \ atomic
pm_runtime_put() Set STARTED flag /
return NETDEV_TX_BUSY
So a STOPPED flag is set in the transmit path when it has stopped
the TX queue, and this pair of operations is also protected by the
spinlock. The resume path only restarts the TX queue if the STOPPED
flag is set. This case isn't a major problem, but it avoids the
"non-trivial amount of useless work" done by the networking stack
when NETDEV_TX_BUSY is returned.
Fixes: 6b51f802d6 ("net: ipa: ensure hardware has power in ipa_start_xmit()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Small ocelot VLAN improvements
This small series propagates some VLAN restrictions via netlink extack
and creates some helper functions instead of open-coding VLAN table
manipulations from multiple places.
This is split from the larger "DSA FDB isolation" series, hence the v2
tag:
https://patchwork.kernel.org/project/netdevbpf/cover/20210818120150.892647-1-vladimir.oltean@nxp.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
