This patch brings no functional change.
There are still duplicate macros across the rtlwifi directory, for example
IQK_DELAY_TIME is defined multiple times, sometimes with different values,
this patch only removes duplicates within the same header file.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast antenna diversity is required only for single chain
chips and the diversity initialization is done in the
per-family board setup routines. Enabling of diversity
should be done based on the calibrated EEPROM/OTP data,
doing it for all chips is incorrect.
Remove the code that sets the fast_div bit for all cards, since
the documentation for the AR_PHY_CCK_DETECT register says:
reg 642: sig_detect_cck
enable_ant_fast_div : Only used for single chain chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a FATAL interrupt is received, a full chip reset is
required, which is done in the main tasklet. But since
the reset routine is scheduled as a work item, make sure
that interrupts are not enabled in the tasklet before the
reset is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than using the chip ID to read only chain-0 CCA
registers and avoid reading chain-1, use the RX chainmask
instead. There are some 1-stream PCI devices based on AR9287
such as TL-WN751ND. Improper NF calibration might result in
DMA errors/timeouts.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove routine _rtl92c_process_phyinfo() by using the equivalent routine
in driver rtlwifi.
This change also allows the removal of 5 additional routines from rtl8192cu.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The other structures in wmi.h are already marked this way.
Without this marking, we get an unaliged access panic in the tilegx kernel:
Starting stack dump of tid 0, pid 0 (swapper) on cpu 35 at cycle 198675113844
frame 0: 0xfffffff7103ada90 ath9k_htc_swba+0x120/0x618 [ath9k_htc]
frame 1: 0xfffffff7103a4b10 ath9k_wmi_event_tasklet+0x1b0/0x270 [ath9k_htc]
frame 2: 0xfffffff700326570 tasklet_action+0x148/0x298
[...]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The band selection and PE control code for the
RT3593 chipsets only handles USB based devices
currently. Due to this limitation RT3593 based
PCIe cards are not working correctly.
On PCIe cards band selection is controlled via
GPIO #8 which is identical to the USB devices.
The LNA PE control is slightly different, all
LNA PEs are controlled by GPIO #4.
Update the code to configure the GPIO_CTRL register
correctly on PCIe devices.
Cc: Steven Liu <steven.liu@mediatek.com>
Cc: JasonYS Cheng <jasonys.cheng@mediatek.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:
* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.
To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.
[1] : http://msujith.org/ath9k/cfp/Malformed-CF-Param.png
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX IQ calibration is disabled by default for AR9462, this
is done using the initvals (reg 0xa644).
But, to compensate for this, the AR_PHY_RX_DELAY register
should be set to the max allowed value when performing
calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function returns a pointer. Hence return NULL instead of false.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Albert Pool <albertpool@solcon.nl>
Reported-by: Michael Landrum <landrummd@gmail.com>
Acked-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.
Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Remove duplicate array mappings.
* Fix ETSI CCA compliance.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust the CCA values based on the regulatory domain
present in the EEPROM.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are 2 types of WB335 cards, 1-antenna and 2-antenna.
Identify them based on PCI subsystem IDs, this will be used
for MCI/BTCOEX tweaks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These cards are based on WB335/AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program the HW registers (AR_PHY_CCK_DETECT, AR_PHY_MC_GAIN_CTRL)
with the correct values for AR9565 to allow LNA combining.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a default antenna diversity value for AR9565 instead
of relying on the EEPROM/OTP programmed value.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking fixes from David Miller:
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
