This patch adds the pin configuration for ltdc and spi5 controller
on stm32f429-disco board.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Enable spi5's dma configuration for graphics data output to
ilitek ili9341 panel via mipi dbi interface.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
There are several issues with the bluetooth node - the wrong
compatible was used (because the bcm4329 compatible didn't exist
when the node was added), the max rate was incorrect (due to
limitations in the samsung TTY driver which have now been fixed),
the clocks were not assigned properly so some rates didn't work,
and the some pinctrl settings weren't explicitly set. Fix all
of the above issues.
While we're at it, update from the deprecated host-wakeup-gpios
property to the host-wake interrupt.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a BMA023 accelerometer attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a GP2A light/proximity sensor attached over i2c-gpio.
As the chip outputs a current and the board has no current ADC, a
current shunt resistor and a voltage ADC are used.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Correct the fuelgauge definition because only the fuelgauge on
fascinate4g has interrupt support (and even then it was wrong).
Also, assign the GPIO pinctrl so the interrupt is properly configured
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The GPH3 pins on s5pv210 have interrupt support and had the
interrupt-cells property but was missing the interrupt-controller
property.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for the BCM4354 Bluetooth chip on the serial bus #0 on
the Exynos3250-based Artik5 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On Exynos5422/5800 the regulator supply for the A15 cores ("vdd_arm") is
coupled with the regulator supply for the SoC internal circuits
("vdd_int"), thus all operating points that modify one of those supplies
have to specify a triplet of the min/target/max values to properly work
with regulator coupling.
Fixes: eaffc4de16 ("ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set smbus_en of IO expander to 1 in order to be able to read sensor.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
EFI on ARM only supports short descriptors, and given that it mandates
that the MMU and caches are on, it is implied that booting in HYP mode
is not supported.
However, implementations of EFI exist (i.e., U-Boot) that ignore this
requirement, which is not entirely unreasonable, given that it makes
HYP mode inaccessible to the operating system.
So let's make sure that we can deal with this condition gracefully.
We already tolerate booting the EFI stub with the caches off (even
though this violates the EFI spec as well), and so we should deal
with HYP mode boot with MMU and caches either on or off.
- When the MMU and caches are on, we can ignore the HYP stub altogether,
since we can carry on executing at HYP. We do need to ensure that we
disable the MMU at HYP before entering the kernel proper.
- When the MMU and caches are off, we have to drop to SVC mode so that
we can set up the page tables using short descriptors. In this case,
we need to install the HYP stub as usual, so that we can return to HYP
mode before handing over to the kernel proper.
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Redefine GZIP, BZIP2, LZOP variables as KGZIP, KBZIP2, KLZOP resp.
GZIP, BZIP2, LZOP env variables are reserved by the tools. The original
attempt to redefine them internally doesn't work in makefiles/scripts
intercall scenarios, e.g., "make GZIP=gzip bindeb-pkg" and results in
broken builds. There can be other broken build commands because of this,
so the universal solution is to use non-reserved env variables for the
compression tools.
Fixes: 8dfb61dcba ("kbuild: add variables for compression tools")
Signed-off-by: Denis Efremov <efremov@linux.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox nodes defined in various dts files have been moved to
common dra7-ipu-dsp-common.dtsi and dra74-ipu-dsp-common.dtsi files
in commit a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes
into common files"), but the nodes were erroneously left out in the
dra7-evm-common.dtsi file. Fix this by removing these duplicate nodes.
Fixes: a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries
for IPU/DSP timers") was added to allow the OMAP clocksource timer
driver to use the clock aliases when reconfiguring the parent clock
source for the timer functional clocks after the timer_sys_ck clock
aliases got cleaned up in commit a8202cd517 ("clk: ti: dra7: drop
unnecessary clock aliases").
The above patch however has missed adding the entries for couple of
timers (14, 15 and 16), and also added erroneously in the parent
ti-sysc nodes for couple of clocks (timers 4, 5 and 6). Fix these
properly, so that any of these timers can be used with OMAP remoteproc
IPU and DSP devices. The always-on timers 1 and 12 are not expected
to use this clock source, so they are not modified.
Fixes: 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries for IPU/DSP timers")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Figure 16-23 define sysconfig register and soft_reset
are in first position corresponding to SYSC_OMAP4_SOFTRESET defined
in ti-sysc.h.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Table 2-1 defines USBSS - USB Queue Manager in memory region
0x4740 0000 to 0x4740 7FFF.
Looks like the older TRM revisions list the range from 0x5000 to 0x8000
as reserved.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
