As a step towards consolidating code, consistently set the
number of ports in the private state structure, and make use of it in
loops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will let us use the switch product IDs in the common source code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common initialization functions will be needed to enable
HW bridging support.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up the common code for setting up hardware bridging
and access to the forwarding database.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 has support for EEE. Check for the product ID and call
the common code if applicable.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable by using defines for the switch IDs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the switch id and save it away in the private mv88x6xxx structure
in a centralised piece of code, rather than each driver doing it itself.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for manipulating switch fdb entries by pointing to the
ndo_fdb functions implemented for mv88e6xxxx.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No vlan support at this time.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge support is similar for all chips supported by the mv88e6xxx code,
so add the code there.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will simplify adding offloaded bridge support later on.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prepares the driver for hardware bridging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split mv88e6xxx_reg_read and mv88e6xxx_reg_write into two functions each,
one to acquire smi_mutex and one to get struct mii_bus *bus from
struct dsa_switch *ds and to call the actual read/write function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datasheet says that the Message Port bit should not be set for the CPU port.
Having it set causes DSA tagged packets to be sent to the CPU port roughly
every 30 seconds. Those packets are the same as real packets forwarded between
switch ports if the switch is configured for switching between multiple ports.
The packets are then bridged by the software bridge, resulting in duplicated
packets on the network.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide mv88e6xxx_setup_port_common() for common port initialization.
Currently only write Port 1 Control and VLAN configuration since
this will be needed for hardware bridging. More can be added later
if desired/needed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code used and needed in mv886xxx.c should be initialized there as well,
so factor it out from the individual initialization files.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This would fix randconfig compile error:
net/built-in.o: In function `netdev_switch_fib_ipv4_abort':
(.text+0xf7811): undefined reference to `fib_flush_external'
Also it fixes following warnings:
warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET)
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE configuration is similar for the various MV88E6xxx chips.
Add generic support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading 64-bits register was not working because we inverted the steps
between reading the lower 32-bits of the register and reading the upper
32-bits. Swapping these operations is how the HW guarantees that 64-bits
reads are latched correctly. We only have a handful of 64-bits registers
for now, mostly MIB counters, so the imapct is low.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is configured to use single chip addressing mode, the
phy devices of the port are not accessible on the host MDIO
bus. Instead the switch internal MDIO bus must be used. For this to
work, the phy polling unit must be enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the power on/off recommended procedure for the Single GPHY we
have on our Starfighter 2 switch. In order to make sure we get proper
LED link/activity signaling during suspend, switch the link indication
from the Switch/MAC to the PHY.
Finally, since the GPHY needs to be reset to be put in low power mode,
we will loose any context applied to it: workarounds, EEE etc.. so we
need to call phy_init_hw() to get our fixups re-applied successfully.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code that touches the single GPHY register from
bcm_sf2_sw_resume() to a separate function since we will have to
enable/disable the GPHY from different locations, and we want the code
to be self-contained.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where there is only one switch, no routing table will have
been allocated, so do not dereference it in this case.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some busy bits are available in the global register 1, such as the ATU
Busy bit. We may want to use this function to wait for them to change,
so add a new parameter to mv88e6352_wait() instead of hard-coding
REG_GLOBAL2.
In the meantime, since the REG_READ() macro already checks for error,
remove the redundant check for ret < 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds debug messages for the generic mv88e6xxx read and write
routines. The output is similar to this:
mdio-gpio mdio-gpio.0: <- addr: 0x1b reg: 0x05 val: 0x4000
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x07 val: 0x3113
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x08 val: 0x0330
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x09 val: 0x0000
This is convenient to dynamically debug operations through debugfs with:
echo file mv88e6xxx.c +p > <debugfs>/dynamic_debug/control
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the interrupt disabling in a function: bcm_sf2_intr_disable()
since we are doing the same thing in the setup and suspend paths.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do the following:
select FIXED_PHY if NET_DSA_BCM_SF2=y, as this implies that we will not be
able to build and/or run the driver correctly when built as a module,
which is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()").
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ports of the switch that we define as "fixed PHYs" such as MoCA, we
would have our Port 7 special handling that would allow us to assert the
link status indication.
For other ports, such as e.g: RGMII_1 connected to a cable modem, we
would rely on whatever the bootloader has left configured, which is a
bad assumption to make, we really need to force the link status
indication here.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our boot agent may have left the switch in an certain configuration
state, make sure we issue a software reset prior to configuring the
switch in order to ensure the HW is in a consistent state, in particular
transmit queues and internal buffers.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we fail to ioremap() one of our registers, we would be leaking
existing mappings, unwind those accordingly on errors.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6171 driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip also has a temperature sensor which can be read using the
common code. In order to use it, add the needed mutex protection for
accessing registers via the shared code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method to read the temperature used in the mve6123_61_65 driver
can also be used for other chips. Move the code into the shared code
base of mv88e6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 is very similar to the mv88e6171. So extend the
mv88e6171 driver to support it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display sw_in_discards, sw_in_filtered, and sw_out_filtered for chips
supported by mv88e6123_61_65 and mv88e6352 drivers.
The variables are provided in port registers, not the normal status registers.
Mark by adding 0x100 to the register offset and add special handling code
to mv88e6xxx_get_ethtool_stats.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6123_61_65 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6352 supports read and write access to its configuration eeprom.
There is no means to detect if an EEPROM is connected to the switch.
Also, the switch supports EEPROMs with different sizes, but can not detect
or report the type or size of connected EEPROMs. Therefore, do not implement
the get_eeprom_len callback but depend on platform or devicetree data to
provide information about EEPROM presence and size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6123 and compatible chips support reading the chip temperature
from PHY register 6:26.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6352 supports reading the chip temperature from two PHY registers,
6:26 and 6:27. Report it using the more accurate register 6:27.
Also report temperature limit and alarm.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6176 is mostly compatible to MV88E6352 and is documented
in the same functional specification. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report known silicon revisions when probing Marvell 88E6131 switches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report known silicon revisions when probing Marvell 88E6060 switches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6171 can support two different tagging protocols, DSA and
EDSA. The switch driver structure only allows one protocol to be
enumerated, and DSA was chosen. However the Kconfig entry ensures the
EDSA tagging code is built. With a minimal configuration, we then end
up with a mismatch. The probe is successful, EDSA tagging is used, but
the switch is configured for DSA, resulting in mangled packets.
Change the switch driver structure to enumerate EDSA, fixing the
mismatch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 42f2725394 ("net: DSA: Marvell mv88e6171 switch driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD 406783067 PUD 406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<ffffffff81781de3>] mutex_lock+0x23/0x37
[<ffffffff81533244>] mdiobus_read+0x34/0x60
[<ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0
Fixes: b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tag_protocol is now an enum, so drivers have to check against it.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_DSA_BCM_SF2 need HAS_IOMEM, so depend on it, the related error (with
allmodconfig under um):
CC [M] drivers/net/dsa/bcm_sf2.o
drivers/net/dsa/bcm_sf2.c: In function ‘bcm_sf2_sw_setup’:
drivers/net/dsa/bcm_sf2.c:487:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(*base);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When EEE is enabled, negotiate this feature with the PHY and make sure
that the capability checking, local EEE advertisement, link partner EEE
advertisement and auto-negotiation resolution returned by phy_init_eee()
is positive, and enable EEE at the switch level.
While querying the current EEE settings, verify the low-power indication
and indicate its status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SF2 switch driver is already architected around per-port
enable/disable callbacks, so we just need a slight update to our
existing bcm_sf2_port_setup() resp. bcm_sf2_port_disable() functions to
be suitable as callbacks for port_enable/port_disable.
We need to shuffle a little the code that does the per-port VLAN
configuration/isolation since ports can now be brought up/down
separately, so we need to make sure that IMP (CPU, management) port is
always included in that specific port setup.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link is down, disable the RGMII interface to conserve as much
power as possible. We re-enable the RGMII interface whenever the link is
detected.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for Wake-on-LAN to work properly, we query the parent network
device Wake-on-LAN features and advertise those. Similarly, when
configuring Wake-on-LAN on a per-port network interface, we make sure
that we do not accept something the master network devices does not
support.
Finally, we need to maintain a bitmask of the ports enabled for
Wake-on-LAN to prevent the suspend() callback from disabling a port that
is used for waking up the system.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the suspend/resume callbacks for the Broadcom Starfighter 2
switch driver. Suspending the switch requires masking interrupts and
shutting down ports. Resuming the switch requires a software reset since
we do not know which power-sate we might be coming from, and re-enabling
the physical ports that are used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated BCM7xxx PHY contains no useful revision information
in its MII_PHYSID2 bits 3:0, that information is instead contained in
the SWITCH_REG_PHY_REVISION register.
Read this register, store its value, and return it by implementing the
dsa_switch::get_phy_flags() callback accordingly. The register layout is
already matching what the BCM7xxx PHY driver is expecting to find.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Marvell driver with some cleanups by Claudio Leite
and myself.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Claudio Leite <leitec@staticky.com>
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1da ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.
Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:
- configuration of the external switch port interface: MII, RevMII,
RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
unused
Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the helper function to retrieve the driver private context instead of
using (void *)(ds + 1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix DSA whitespace issues reported by checkpatch.pl
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DSA printk calls to netdev_info calls as recommended by
checkpatch.pl.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DSA msleep calls to timeout/usleep_range calls
as reported by checkpatch.pl.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DSA driver comments to network-style comments as reported by
checkpatch.pl. Fix spelling error.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 82167cb8c6 ('net: dsa/slave: Fix
compilation warnings') fixed one possible invalid configuration
(NET_DSA enabled with no trailer formats) but added others: drivers
can select NET_DSA without its dependencies being met.
It's not very useful to make either the DSA core or the tagging
formats manually selectable without a driver to use them, so:
1. Define a hidden HAVE_NET_DSA option and move the dependencies of
NET_DSA to that. While we're at it, drop the deprecated
EXPERIMENTAL dependency.
2. Make NET_DSA and the drivers dependent on HAVE_NET_DSA.
3. Hide the tagging format options again.
4. Make drivers select both NET_DSA and the appropriate tagging format
option.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when none of CONFIG_NET_DSA_TAG_DSA, CONFIG_NET_DSA_TAG_EDSA and
CONFIG_NET_DSA_TAG_TRAILER is defined, we get following compilation warnings:
net/dsa/slave.c:51:12: warning: 'dsa_slave_init' defined but not used [-Wunused-function]
net/dsa/slave.c:60:12: warning: 'dsa_slave_open' defined but not used [-Wunused-function]
net/dsa/slave.c:98:12: warning: 'dsa_slave_close' defined but not used [-Wunused-function]
net/dsa/slave.c:116:13: warning: 'dsa_slave_change_rx_flags' defined but not used [-Wunused-function]
net/dsa/slave.c:127:13: warning: 'dsa_slave_set_rx_mode' defined but not used [-Wunused-function]
net/dsa/slave.c:136:12: warning: 'dsa_slave_set_mac_address' defined but not used [-Wunused-function]
net/dsa/slave.c:164:12: warning: 'dsa_slave_ioctl' defined but not used [-Wunused-function]
Earlier approach to fix this was discussed here:
lkml.org/lkml/2012/10/29/549
This is another approach to fix it. This is done by some changes in config
options, which make more sense than the earlier approach. As, atleast one
tagging option must always be selected for using net/dsa/ infrastructure, this
patch selects NET_DSA from tagging configs instead of having it as an selectable
config.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An implicit instance of module.h leaked back into existence
and was masking the fact that these drivers weren't calling
out the include for itself. Fix the drivers before we remove
the implicit include path via net/netprio_cgroup.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reporting of silicon revision during the probe function for Marvell 88E6123/88E6161/88E6165 switches.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for specific hardware belongs under drivers/net/ not net/.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
