GIC400 has full support for virtualization, and yet the tegra186
DT doesn't expose the GICH/GICV regions (despite exposing the
maintenance interrupt that only makes sense for virtualization).
Add the missing regions, based on the hunch that the HW doesn't
use the CPU build-in interfaces, but instead the external ones
provided by the GIC. KVM's virtual GIC now works with this change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the description of CPU PMUs for both the Denver and A57 clusters,
which enables the perf subsystem.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the device-tree board file was added for the Tegra234 VDK simulator
it incorrectly used the names 'cbb' and 'sdhci' instead of 'bus' and
'mmc', respectively. The names 'bus' and 'mmc' are required by the
device-tree json-schema validation tools. Therefore, fix this by
renaming these nodes accordingly.
Fixes: 639448912b ("arm64: tegra: Initial Tegra234 VDK support")
Reported-by: Ashish Singhal <ashishsingha@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
USB host mode is broken on the OTG port of Jetson TX1 platform because
the USB_VBUS_EN0 regulator (regulator@11) is being overwritten by the
vdd-cam-1v2 regulator. This commit rearranges USB_VBUS_EN0 to be
regulator@14.
Fixes: 257c8047be ("arm64: tegra: jetson-tx1: Add camera supplies")
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Jetson Xavier NX board routes UARTA to the 40-pin header and UARTC
to a 12-pin debug header. The UARTs can be used by either the Tegra
Combined UART (TCU) driver or the Tegra 8250 driver. By default, the
TCU will use UARTC on Jetson Xavier NX. Currently, device-tree for
Xavier NX enables the TCU and the Tegra 8250 node for UARTC. Fix this
by disabling the Tegra 8250 node for UARTC and enabling the Tegra 8250
node for UARTA.
Fixes: 3f9efbbe57 ("arm64: tegra: Add support for Jetson Xavier NX")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit ff4c371d2b ("arm64: defconfig: Build ADMA and ACONNECT driver")
enable the Tegra ADMA and ACONNECT drivers and this is causing resume
from system suspend to fail on Jetson TX2. Resume is failing because the
ACONNECT driver is being resumed before the BPMP driver, and the ACONNECT
driver is attempting to power on a power-domain that is provided by the
BPMP. While a proper fix for the resume sequencing problem is identified,
disable the ACONNECT for Jetson TX2 temporarily to avoid breaking system
suspend.
Please note that ACONNECT driver is used by the Audio Processing Engine
(APE) on Tegra, but because there is no mainline support for APE on
Jetson TX2 currently, disabling the ACONNECT does not disable any useful
feature at the moment.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SDM630/660 SoCs (and variants) have another clock source
for the PHY, which must be set to a rate that's equal or
greater than the CSI PHY timer clock: failing to do this
will produce PHY overflows when trying to get a stream from
a very high bandwidth camera sensor and outputting no frame
or a partial one.
Since I haven't found any usecase in which the csiX_phy
clock needs to be higher than the csiXphy_timer, let's just
set the same rate on both, which seems to work just perfect.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSIPHY on SDM630/660 needs a slightly longer T_HS_CLK_MISS
configuration on lanes CFG4.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the Qualcomm SDM630/636/660 and SDA variants' camera
subsystem. These SoCs are equipped with:
- 3x CSI PHY 3-Phase v1.0 (downstream csiphy-v3.5)
- 4x CSID v5.0
- 2x ISPIF v3.0
- 2x VFE 4.8
As a note, this camera subsystem is very similar to the one that
is found in the MSM8998/APQ8098 SoCs.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add bindings for qcom,sdm660-camss in order to support the camera
subsystem on SDM630/660 and SDA variants.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the support for VFE 4.8 in the camss-vfe-4-7 driver, as this one
really is a minor revision, requiring the very same management and
basically having the same register layout as VFE 4.7, but needing
a different QoS and DS configuration, using a different register to
enable the wm and habing the same UB size for both instances (instead
of a different size between instance 0 and 1).
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation to add support for VFE 4.8, rename these functions
by adding the vfe version that they are referred to (for example,
vfe_get_ub_size -> vfe47_get_ub_size), as these are the only ones
that will be different for the VFE version 4.8.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Resetting the ISPIF VFE0 context is wrong if we are using the VFE1
for dual-camera or simply because a secondary camera is connected
to it: in this case the reset will always happen on the VFE0 ctx
of the ISPIF, which is .. useless.
Fix this usecase by adding the ISPIF_RST_CMD_1 address and choose
where to do the (or what to) reset based on the VFE line id.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The enum rc_proto value RC_PROTO_MAX has no documentation, this is causing
a warning while building the documentation.
Fixes: 72e637fec5 ("media: rc: validate that "rc_proto" is reasonable")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This allows the timeout to be set with the LIRC_SET_REC_TIMEOUT ioctl.
The timeout was hardcoded at just over 20ms, but returned 120ms when
queried with the LIRC_GET_REC_TIMEOUT ioctl.
This also ensures the idle threshold is set correctly with a base clock
other than 8Mhz.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If a user holds a button down on a remote, then no ir idle interrupt will
be generated until the user releases the button, depending on how quickly
the remote repeats. No IR is processed until that point, which means that
holding down a button may not do anything.
This also resolves an issue on a Cubieboard 1 where the IR receiver is
picking up ambient infrared as IR and spews out endless
"rc rc0: IR event FIFO is full!" messages unless you choose to live in
the dark.
Cc: stable@vger.kernel.org
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The flag V4L2_SUBDEV_FL_HAS_EVENTS is required if the subdev can
generate events. It can create events from the ctrl handler, therefore
this is required.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Comment has 'the' repeated twice. Let's clean it up.
This patch reduces checkpatch warnings for this file to nil.
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OTP data access of ov2740 need enable the streaming mode to load
and it could be done in any time, so driver need allow the OTP
data access during streaming instead of return EBUSY, this patch
try to read the OTP data out in STREAMON if OTP data is not ready
before first time streaming start.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OTP data access of ov2740 in probe need power up, it may cause
the camera flash LED blink during probe if the LED use same power
rail with camera, this patch move the OTP data access out of
probe, it will only occur on demand from user by nvmem sysfs.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support of BT656 embedded synchronization bus.
This mode allows to save hardware synchro lines hsync & vsync by replacing
them with synchro codes embedded in data stream.
This bus type is only compatible with 8 bits width data bus.
Due to reserved values 0x00 & 0xff used for synchro codes, valid data vary
from 0x1 to 0xfe, this is up to sensor to clip accordingly pixel data. As
a consequence of this clipping, JPEG is not supported with this bus type.
DCMI crop feature is also not available with this bus type.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mayflash/Dragonrise seems to have yet another device ID for one of their
Gamecube controller adapters. Previous to this commit, the adapter
registered only one /dev/input/js* device, and all controller inputs (from
any controller) were mapped to this device. This patch defines the 1846
USB device ID and enables the HID_QUIRK_MULTI_INPUT quirk for it, which
fixes that (with the patch, four /dev/input/js* devices are created, one
for each of the four controller ports).
Signed-off-by: Ethan Warth <redyoshi49q@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support of BT656 embedded synchronization bus mode in DCMI driver.
Add "bus-type" property and make it required so that there is no
ambiguity between parallel mode (bus-type=5) and BT656 mode (bus-type=6).
BT656 mode allows to save hardware synchro lines hsync & vsync by replacing
them with synchro codes embedded in data stream, hence hsync-active &
vsync-active properties are useless in this mode.
With DCMI, BT656 bus mode is only compatible with 8 bits width data bus.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the OminiVision ov9734 image sensor
which can deliver maximum 720p image frames at 30 fps. This driver
also add vertical blanking, exposure, test pattern, digital and analog
gain control for the image sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enables three buttons (Fn1, Fn2, and Fn3) on the ELECOM M-XGL20DLBK
wireless mouse.
While this mouse is EX-G brand, report descriptor is a bit different
from EX-G trackball mouse. To enable extra buttons, report should be
rewritten in a similar way to trackballs, but with different position
parameters.
Signed-off-by: YOSHIOKA Takuma <lo48576@hard-wi.red>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The report descriptor for EX-G wireless mouse (M-XGL20DLBK) is a bit
different from that for trackball mice such as DEFT. For such mouse, the
current `mouse_button_fixup` cannot be used as is, because it uses
hard-coded indices for a report descriptor.
Add parameters to `mouse_button_fixup` function, in order to support
fixing report descriptors for more models.
Signed-off-by: YOSHIOKA Takuma <lo48576@hard-wi.red>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These are never modified, so make them const to allow the compiler to put
them in read-only memory. It also allows the compiler to shrink the
resulting module with ~900 bytes, test-built with gcc 10.2 on x86_64.
text data bss dec hex filename
204377 42832 576 247785 3c7e9 drivers/hid/wacom_old.ko
204240 42064 576 246880 3c460 drivers/hid/wacom_new.ko
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge in support for the new DOMAIN_ATTR_IO_PGTABLE_CFG domain attribute
and its associated IO_PGTABLE_QUIRK_ARM_OUTER_WBWA io-pgtable quirk,
as these are needed to enable support for Qualcomm's System Cache in
conjunction with their GPU SMMU.
* for-next/iommu/io-pgtable-domain-attr:
iommu/io-pgtable-arm: Add support to use system cache
iommu/io-pgtable: Add a domain attribute for pagetable configuration
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a goto statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a couple
of warnings by explicitly adding a couple of break statements instead
of letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech V470 bluetooth mouse supports HID++-1.0 over bluetooth,
add its id to the hidpp driver so that it handles it.
This enables battery monitoring support.
Note this mouse does not support hi-resolution scroll-wheel events.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This assignment to rv is unused in an error path. So remove it.
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
fixed the coccicheck:
drivers/spi/spi-dw-bt1.c:220:27-30: ERROR: Missing
resource_size with mem.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/1606114975-31362-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When SPI DW memory ops support was introduced, there was a check for
excluding controllers which supplied their own CS function. Even so,
the mem_ops pointer is *always* presented to the SPI core.
This causes the SPI core sanity check in spi_controller_check_ops() to
refuse registration, since a mem_ops pointer is being supplied without
an exec_op member function.
The end result is failure of the SPI DW driver on sparx5 and similar
platforms.
The fix in the core SPI DW driver is to avoid presenting the mem_ops
pointer if the exec_op function is not set.
Fixes: 6423207e57 (spi: dw: Add memory operations support)
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201120213414.339701-1-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return a negative error code from the error handling case
instead of 0 in function wm_adsp_load(), as done elsewhere in this
function.
Fixes: 170b1e123f ("ASoC: wm_adsp: Add support for new Halo core DSPs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Luo Meng <luomeng12@huawei.com>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201123133839.4073787-1-luomeng12@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The hid-sony driver has custom DS4 connect/disconnect logic for the
DS4 dongle, which is a USB dongle acting as a proxy to Bluetooth
connected DS4.
The connect/disconnect logic works fine generally, however not in
conjunction with Steam. Steam implements its own DS4 driver using
hidraw. Both hid-sony and Steam are issuing their own HID requests
and are racing each other during DS4 dongle connect/disconnect
resulting in a kernel crash in hid-sony.
The problem is that upon a DS4 connect to the dongle, hid-sony kicks
of 'ds4_get_calibration_data' from within its dongle hotplug code.
The calibration code issues raw HID feature report for reportID 0x02.
When Steam is running, it issues a feature report for reportID 0x12
typically just prior to hid-sony requesting feature reportID 0x02.
The result is that 'ds4_get_calibration_data' receives the data Steam
requested as that's the HID report returing first. Currently this
results in it processing invalid data, which ultimately results in a
divide by zero upon a future 'dualshock4_parse_report'.
The solution for now is to check within 'ds4_get_calibration_data' to
check if we received data for the feature report we issued and if not
retry. This fixes bug 206785.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS4 dongle reports fw_version and hw_version as 0 when no actual
DS4 is connected to it. This prevents cleaning up sysfs nodes upon
device remove.
This patch decouples sysfs cleanup from the fw_version and hw_version
values by introducing boolean values.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch moves the power supply status logic to DS3/DS4 parse_report,
to allow for more accurate DS4 status reporting.
The DS4 power status code was actually incorrect, but reported okay'ish
data in most cases. There was a different interpretation of the battery_info
values 0-10 or 0-9 depending on cable state. It added +1 to extend the range
to 0-10. This is actually incorrect, there is no different range. Values
higher than 11 actually indicates 'full' and 14/15 'error' for which we
reported 100% and a valid power state.
Moving the status logic to parse_report avoids having to pass more state
to the generic sony_battery_get_property and simplifies the code.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new iommu domain attribute DOMAIN_ATTR_IO_PGTABLE_CFG
for pagetable configuration which initially will be used to
set quirks like for system cache aka last level cache to be
used by client drivers like GPU to set right attributes for
caching the hardware pagetables into the system cache and
later can be extended to include other page table configuration
data.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/9190aa16f378fc0a7f8e57b2b9f60b033e7eeb4f.1606287059.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
