Avoid problems with BIOS implementations which don't report all used
resources to the OS by only allocating a 256GB window directly below the
hardware limit (from the BKDG, sec 2.4.6).
Fixes a silent reboot loop reported by Aaro Koskinen <aaro.koskinen@iki.fi>
on an AMD-based MSI MS-7699/760GA-P43(FX) system. This was apparently
caused by RAM or other unreported hardware that conflicted with the new
window.
Link: https://support.amd.com/TechDocs/49125_15h_Models_30h-3Fh_BKDG.pdf
Link: https://lkml.kernel.org/r/20180105220412.fzpwqe4zljdawr36@darkstar.musicnaut.iki.fi
Fixes: fa564ad963 ("x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: changelog, comment, Fixes:]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
This seems to be a copy&paste error. With the fix the uvc gadget now can
be created by following the instrucitons.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a GPIO which is high by default, and initialize the
driver in USB Hub mode, initialization fails with:
[ 111.757794] usb3503 0-0008: SP_ILOCK failed (-5)
The reason seems to be that the chip is not properly reset.
Probe does initialize reset low, however some lines later the
code already set it back high, which is not long enouth.
Make sure reset is asserted for at least 100us by inserting a
delay after initializing the reset pin during probe.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only try to enable a 64-bit window on AMD CPUs when "pci=big_root_window"
is specified.
This taints the kernel because the new 64-bit window uses address space we
don't know anything about, and it may contain unreported devices or memory
that would conflict with the window.
The pci_amd_enable_64bit_bar() quirk that enables the window is specific to
AMD CPUs. The generic solution would be to have the firmware enable the
window and describe it in the host bridge's _CRS method, or at least
describe it in the _PRS method so the OS would have the option of enabling
it.
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: changelog, extend doc, mention taint in dmesg]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
This adds a memory barrier when performing a lookup into
the vmcs_field_to_offset_table. This is related to
CVE-2017-5753.
Signed-off-by: Andrew Honig <ahonig@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Here are a couple of new device ids for cp210x.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LzG1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.15-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.15-rc8
Here are a couple of new device ids for cp210x.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commits ae1f576707
and ac9b305caa.
If the hardware doesn't support MOVBE, but L0 sets CPUID.01H:ECX.MOVBE
in L1's emulated CPUID information, then L1 is likely to pass that
CPUID bit through to L2. L2 will expect MOVBE to work, but if L1
doesn't intercept #UD, then any MOVBE instruction executed in L2 will
raise #UD, and the exception will be delivered in L2.
Commit ac9b305caa is a better and more
complete version of ae1f576707 ("KVM: nVMX: Do not emulate #UD while
in guest mode"); however, neither considers the above case.
Suggested-by: Jim Mattson <jmattson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Patch "mm,vmscan: mark register_shrinker() as __must_check" is
queued for 4.16 in linux-mm and adds a warning about the unchecked
call to register_shrinker:
arch/x86/kvm/mmu.c:5485:2: warning: ignoring return value of 'register_shrinker', declared with attribute warn_unused_result [-Wunused-result]
This changes the kvm_mmu_module_init() function to fail itself
when the call to register_shrinker fails.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have a hole in our busy-stat accounting if the pmu is enabled during
a long running batch, the pmu will not start accumulating busy-time
until the next context switch. This then fails tests that are only
sampling a single batch.
v2: Count each active port just once (context in/out events are only on
the first and last assignment to a port).
v3: Avoid hardcoding knowledge of 2 submission ports
Fixes: 30e17b7847 ("drm/i915: Engine busy time tracking")
Testcase: igt/perf_pmu/busy-start
Testcase: igt/perf_pmu/busy-double-start
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111073031.14614-1-chris@chris-wilson.co.uk
As we kmalloc our dynamic sysfs attributes, we have to give them an
external static lock_class_key for them to use with lockdep.
Fixes: 109ec55837 ("drm/i915/pmu: Only enumerate available counters in sysfs")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111140402.3984-1-chris@chris-wilson.co.uk
Four commits here, including two that were tagged but never merged.
Three of them are for the HPT resizing code; two of those fix a
user-triggerable use-after-free in the host, and one that fixes
stale TLB entries in the guest. The remaining commit fixes a bug
causing PR KVM guests under PowerVM to fail to start.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVfPgAAoJEJ2a6ncsY3GfA10IANZMkwtIpqxGlsAeXKr5bWdl
iXYD9ymb2/FOHBbg6v8Eh6Gb1ycjzXpXqn74/Y9TE4Ort7mdiH+W6kXYEsMqL8yg
7Uwnj8DuWFuFxX0x0V4SJQzgdCnOefVcfoo/RnLUzmLsW0Vqtr3A1djM5iHlxFvv
ntkNtGYPOoaHl6rjtfHTDfLWN/DzEJbaIU/0O1LIkBxPG4STzSXErAucLL46Pa/X
NuPO2HfpxQiacHVG62iy89eJeAcraEAXnH5e6eVPRQQqh3DSIERMU6n6jXyZeMU5
NWX8Qme3VGBpiJOiCGMvMrnJmQmMTSWTtkGljyaFy+vZWMqGZ6xJ3wIP+5t9d+Q=
=dw6K
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
PPC KVM fixes for 4.15
Four commits here, including two that were tagged but never merged.
Three of them are for the HPT resizing code; two of those fix a
user-triggerable use-after-free in the host, and one that fixes
stale TLB entries in the guest. The remaining commit fixes a bug
causing PR KVM guests under PowerVM to fail to start.
For example, when two APF's for page ready happen after one exit and
the first one becomes pending, the second one will result in #DF.
Instead, just handle the second page fault synchronously.
Reported-by: Ross Zwisler <zwisler@gmail.com>
Message-ID: <CAOxpaSUBf8QoOZQ1p4KfUp0jq76OKfGY4Uxs-Gg8ngReD99xww@mail.gmail.com>
Reported-by: Alec Blayne <ab@tevsa.net>
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Switch over to dynamically creating device attributes, which are in turn
used by the perf core to expose available counters in sysfs.
This way we do not expose counters which are not avaiable on the current
platform, and are so more consistent between what we reply to open
attempts via the perf_event_open(2), and what is discoverable in sysfs.
v2:
* Simplify attribute pointer freeing loop.
* Changed attr init from macro to function.
* More common error unwind. (Chris Wilson)
* Rename some locals. (Chris Wilson)
v3:
* Fixed double semi-colon. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111083525.32394-1-tvrtko.ursulin@linux.intel.com
With firmware 1.07 having fixed the state corruption issue, we can enable
the headless GT performance workaround for CNL as well. (Equivalent to
b68763741a ("drm/i915: Restore GT performance in headless mode with DMC
loaded") on other affected platforms.)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111082417.795-1-tvrtko.ursulin@linux.intel.com
Geminilake requires the 3D driver to select whether barriers are
intended for compute shaders, or tessellation control shaders, by
whacking a "Barrier Mode" bit in SLICE_COMMON_ECO_CHICKEN1 when
switching pipelines. Failure to do this properly can result in GPU
hangs.
Unfortunately, this means it needs to switch mid-batch, so only
userspace can properly set it. To facilitate this, the kernel needs
to whitelist the register.
The workarounds page currently tags this as applying to Broxton only,
but that doesn't make sense. The documentation for the register it
references says the bit userspace is supposed to toggle only exists on
Geminilake. Empirically, the Mesa patch to toggle this bit appears to
fix intermittent GPU hangs in tessellation control shader barrier tests
on Geminilake; we haven't seen those hangs on Broxton.
v2: Mention WA #0862 in the comment (it doesn't have a name).
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180105085905.9298-1-kenneth@whitecape.org
(cherry picked from commit ab062639ed)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pull vfs regression fix from Al Viro/
Fix a leak in socket() introduced by commit 8e1611e235 ("make
sock_alloc_file() do sock_release() on failures").
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix a leak in socket(2) when we fail to allocate a file descriptor.
Pull networking fixes from David Miller:
1) BPF speculation prevention and BPF_JIT_ALWAYS_ON, from Alexei
Starovoitov.
2) Revert dev_get_random_name() changes as adjust the error code
returns seen by userspace definitely breaks stuff.
3) Fix TX DMA map/unmap on older iwlwifi devices, from Emmanuel
Grumbach.
4) From wrong AF family when requesting sock diag modules, from Andrii
Vladyka.
5) Don't add new ipv6 routes attached to the null_entry, from Wei Wang.
6) Some SCTP sockopt length fixes from Marcelo Ricardo Leitner.
7) Don't leak when removing VLAN ID 0, from Cong Wang.
8) Hey there's a potential leak in ipv6_make_skb() too, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
ipv6: sr: fix TLVs not being copied using setsockopt
ipv6: fix possible mem leaks in ipv6_make_skb()
mlxsw: spectrum_qdisc: Don't use variable array in mlxsw_sp_tclass_congestion_enable
mlxsw: pci: Wait after reset before accessing HW
nfp: always unmask aux interrupts at init
8021q: fix a memory leak for VLAN 0 device
of_mdio: avoid MDIO bus removal when a PHY is missing
caif_usb: use strlcpy() instead of strncpy()
doc: clarification about setting SO_ZEROCOPY
net: gianfar_ptp: move set_fipers() to spinlock protecting area
sctp: make use of pre-calculated len
sctp: add a ceiling to optlen in some sockopts
sctp: GFP_ATOMIC is not needed in sctp_setsockopt_events
bpf: introduce BPF_JIT_ALWAYS_ON config
bpf: avoid false sharing of map refcount with max_entries
ipv6: remove null_entry before adding default route
SolutionEngine771x: add Ether TSU resource
SolutionEngine771x: fix Ether platform data
docs-rst: networking: wire up msg_zerocopy
net: ipv4: emulate READ_ONCE() on ->hdrincl bit-field in raw_sendmsg()
...
Got broken by "make sock_alloc_file() do sock_release() on failures" -
cleanup after sock_map_fd() failure got pulled all the way into
sock_alloc_file(), but it used to serve the case when sock_map_fd()
failed *before* getting to sock_alloc_file() as well, and that got
lost. Trivial to fix, fortunately.
Fixes: 8e1611e235 (make sock_alloc_file() do sock_release() on failures)
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In case kfd_get_process_device_data returns null, there are some
null pointer dereferences in functions kfd_bind_processes_to_device
and kfd_unbind_processes_from_device.
Fix this by printing a WARN_ON for PDDs that aren't found and skip
them with continue statements.
Addresses-Coverity-ID: 1463794 ("Dereference null return value")
Addresses-Coverity-ID: 1463772 ("Dereference null return value")
Suggested-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Function ipv6_push_rthdr4 allows to add an IPv6 Segment Routing Header
to a socket through setsockopt, but the current implementation doesn't
copy possible TLVs at the end of the SRH received from userspace.
Therefore, the execution of the following branch if (sr_has_hmac(sr_phdr))
{ ... } will never complete since the len and type fields of a possible
HMAC TLV are not copied, hence seg6_get_tlv_hmac will return an error,
and the HMAC will not be computed.
This commit adds a memcpy in case TLVs have been appended to the SRH.
Fixes: a149e7c7ce ("ipv6: sr: add support for SRH injection through setsockopt")
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_setup_cork() might return an error, while memory allocations have
been done and must be rolled back.
Fixes: 6422398c2a ("ipv6: introduce ipv6_make_skb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Reported-by: Mike Maloney <maloney@google.com>
Acked-by: Mike Maloney <maloney@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of small fixes for mlxsw driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve the sparse warning:
"sparse: Variable length array is used."
Use 2 arrays for 2 PRM register accesses.
Fixes: 96f17e0776 ("mlxsw: spectrum: Support RED qdisc offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After performing reset driver polls on HW indication until learning
that the reset is done, but immediately after reset the device becomes
unresponsive which might lead to completion timeout on the first read.
Wait for 100ms before starting the polling.
Fixes: 233fa44bd6 ("mlxsw: pci: Implement reset done check")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link state and exception interrupts may be masked when we probe.
The firmware should in theory prevent sending (and automasking) those
interrupts if the device is disabled, but if my reading of the FW code
is correct there are firmwares out there with race conditions in this
area. The interrupt may also be masked if previous driver which used
the device was malfunctioning and we didn't load the FW (there is no
other good way to comprehensively reset the PF).
Note that FW unmasks the data interrupts by itself when vNIC is
enabled, such helpful operation is not performed for LSC/EXN interrupts.
Always unmask the auxiliary interrupts after request_irq(). On the
remove path add missing PCI write flush before free_irq().
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add table length check.
DC component expect PP to give max engine clock and
memory clock through pp_get_display_mode_validation_clocks
on DGPU as well.
This patch can fix MultiGPU-Display blank
out with 1 IGPU-4k display and 2 DGPU-two 4K
displays.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just another contact for the amdgpu driver.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Windows added by the BIOS are not marked as 64bit because they are
usually not changeable anyway.
This fixes large BAR support on my new Ryzen build system.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we would completely circumvent that debugging feature.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the PDEs after resetting the huge flag.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Necessary for the next patch.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Try to lock moved BOs if it's successful we can update the
PTEs directly to the new location.
v2: rebase
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can actually handle invalid huge pages perfectly fine now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Suppress warning messages when allocating huge pages fails since we can
always fall back to normal pages.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No one will use this function except ttm_bo_io_mem_pfn() now, so move
the calculation of ttm_bo_default_io_mem_pfn() into ttm_bo_io_mem_pfn()
and do some cleanup.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The default interface situation has been taken into the framework, so
remove the default set of each module.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add smu_free_memory when smu fini to prevent memory leakage
v2: squash in typo fix (Yintian) and warning (Harry)
Signed-off-by: Yintian Tao <yttao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use adev->vm_manager.id_mgr[0].num_ids rather than hardcoded 16.
v2: use AMDGPU_GFXHUB rather than hardcoded 0 (Christian)
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Noticed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add quirks for handling PX/HG systems. In this case, add
a quirk for a weston dGPU that only seems to properly power
down using ATPX power control rather than HG (_PR3).
v2: append a new weston XT
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com> (v2)
Reviewed-and-Tested-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
A vlan device with vid 0 is allow to creat by not able to be fully
cleaned up by unregister_vlan_dev() which checks for vlan_id!=0.
Also, VLAN 0 is probably not a valid number and it is kinda
"reserved" for HW accelerating devices, but it is probably too
late to reject it from creation even if makes sense. Instead,
just remove the check in unregister_vlan_dev().
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: ad1afb0039 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully the last set of fixes for 4.15.
iwlwifi
* fix DMA mapping regression since v4.14
wcn36xx
* fix dynamic power save which has been broken since the driver was commited
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVLeaAAoJEG4XJFUm622bYBUH/2NhQwUJbKIrbxYhYpo0d++8
GK3TjxpzTByCe0nXGUT5iuDaY72i9C2UoLhFQ5smVg04pE0IXQQjZus6vSGx4biz
GUave/SkzL0EruUXjXLBYWiYDND4iynk82gWX2/Lh7qGoT2SQfD5cKz0cMdE5NrW
E7Q1CMiaoB0i9jcksaU2uWA0XPwISxl61kU2dXuKHQOJ1CW1goI/YIHsBajshHmi
ZEfMqxZFE+jz2Kkp4tKhvG/Xva0ylJv8bwK8CMK6MqA8oa3xdgOhv67E9mm7IGpD
ETrRLJNnWGJlnod5u7QOZWcS01gAgT5whCqDl/lTEty0823kvjMQdwckQaIU+AE=
=me16
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Hopefully the last set of fixes for 4.15.
iwlwifi
* fix DMA mapping regression since v4.14
wcn36xx
* fix dynamic power save which has been broken since the driver was commited
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If one of the child devices is missing the of_mdiobus_register_phy()
call will return -ENODEV. When a missing device is encountered the
registration of the remaining PHYs is stopped and the MDIO bus will
fail to register. Propagate all errors except ENODEV to avoid it.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-8 reports
net/caif/caif_usb.c: In function 'cfusbl_device_notify':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]
The compiler require that the input param 'len' of strncpy() should be
greater than the length of the src string, so that '\0' is copied as
well. We can just use strlcpy() to avoid this warning.
Signed-off-by: Xiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kornilios Kourtis <kou@zurich.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
