The driver was using its struct usb_interface pointer as an inverted
disconnected flag and was setting it to NULL before making sure all
completion handlers had run. This could lead to NULL-pointer
dereferences in the dev_err() statements in the completion handlers
which relies on said pointer.
Fix this by using a dedicated disconnected flag.
Note that this is also addresses a NULL-pointer dereference at release()
and a struct usb_interface reference leak introduced by a recent runtime
PM fix, which depends on and should have been submitted together with
this patch.
Fixes: 4212cd74ca ("USB: usb-skeleton.c: remove err() usage")
Fixes: 5c290a5e42 ("USB: usb-skeleton: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fixes issue with Halt Endnpoint Test observed during using g_zero
driver as DUT. Bug occurred only on some testing board.
Endpoint can defer transition to Halted state if endpoint has pending
requests.
Patch add additional condition that allows to return correct endpoint
status during Get Endpoint Status request even if the halting endpoint
is in progress.
Reported-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Tested-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/1570430355-26118-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial fixes for 5.4-rc2
Here's a fix for a long-standing issue in the keyspan driver which could
lead to NULL-pointer dereferences when a device had unexpected endpoint
descriptors.
Included are also some new device IDs.
All but the last two commits have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.4-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: keyspan: fix NULL-derefs on open() and write()
USB: serial: option: add support for Cinterion CLS8 devices
USB: serial: option: add Telit FN980 compositions
USB: serial: ftdi_sio: add device IDs for Sienna and Echelon PL-20
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Note that runtime PM has never actually been enabled for this driver
since the support_autosuspend flag in its usb_driver struct is not set.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the original bindings that were superseeded by the YAML schemas
didn't mention that phy-names was needed, it turns out that phy-names is
required if phys is set according to phy/phy-bindings.txt.
Let's add back those properties.
Fixes: 14ec072a19 ("dt-bindings: usb: Convert USB HCD generic binding to YAML")
Fixes: c93bcace10 ("dt-bindings: usb: Convert the generic OHCI binding to YAML")
Fixes: c3e2485d5f ("dt-bindings: usb: Convert the generic EHCI binding to YAML")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-2-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc points out a suspicious cast from a pointer to an 'int' when
compile-testing on 64-bit architectures.
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_pop_fifo’:
drivers/usb/gadget/udc/lpc32xx_udc.c:1156:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_stuff_fifo’:
drivers/usb/gadget/udc/lpc32xx_udc.c:1257:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
The code works find, but it's easy enough to change the cast to
a uintptr_t to shut up that warning.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190918200201.2292008-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system can hit a deadlock if an xhci adapter breaks while initializing.
The deadlock is between two threads: thread 1 is tearing down the
adapter and is stuck in usb_unlocked_disable_lpm waiting to lock the
hcd->handwidth_mutex. Thread 2 is holding this mutex (while still trying
to add a usb device), but is stuck in xhci_endpoint_reset waiting for a
stop or config command to complete. A reboot is required to resolve.
It turns out when calling xhci_queue_stop_endpoint and
xhci_queue_configure_endpoint in xhci_endpoint_reset, the return code is
not checked for errors. If the timing is right and the adapter dies just
before either of these commands get issued, we hang indefinitely waiting
for a completion on a command that didn't get issued.
This wasn't a problem before the following fix because we didn't send
commands in xhci_endpoint_reset:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
With the patch I am submitting, a duration test which breaks adapters
during initialization (and which deadlocks with the standard kernel) runs
without issue.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Torez Smith <torez@redhat.com>
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Signed-off-by: Torez Smith <torez@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-7-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.
The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.
The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg and dev_err statements in the
completion handlers which relies on said pointer.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes: 9d974b2a06 ("USB: legousbtower.c: remove err() usage")
Fixes: fef526cae7 ("USB: legousbtower: remove custom debug macro")
Fixes: 4dae996380 ("USB: legotower: remove custom debug macro and module parameter")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "run_isr" flag is used for preventing the driver from
calling the interrupt service routine in its runtime resume
callback when the driver is expecting completion to a
command, but what that basically does is that it hides the
real problem. The real problem is that the controller is
allowed to suspend in the middle of command execution.
As a more appropriate fix for the problem, using autosuspend
delay time that matches UCSI_TIMEOUT_MS (5s). That prevents
the controller from suspending while still in the middle of
executing a command.
This fixes a potential deadlock. Both ccg_read() and
ccg_write() are called with the mutex already taken at least
from ccg_send_command(). In ccg_read() and ccg_write, the
mutex is only acquired so that run_isr flag can be set.
Fixes: f0e4cd948b ("usb: typec: ucsi: ccg: add runtime pm workaround")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191004100219.71152-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the redundant disconnect mutex which was introduced after the
open-disconnect race had been addressed generally in USB core by commit
d4ead16f50 ("USB: prevent char device open/deregister race").
Specifically, the rw-semaphore in core guarantees that all calls to
open() will have completed and that no new calls to open() will occur
after usb_deregister_dev() returns. Hence there is no need use the
driver data as an inverted disconnected flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190926091228.24634-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Greg KH, it has been generally agreed that when a USB
driver encounters an unknown error (or one it can't handle directly),
it should just give up instead of going into a potentially infinite
retry loop.
The three codes -EPROTO, -EILSEQ, and -ETIME fall into this category.
They can be caused by bus errors such as packet loss or corruption,
attempting to communicate with a disconnected device, or by malicious
firmware. Nowadays the extent of packet loss or corruption is
negligible, so it should be safe for a driver to give up whenever one
of these errors occurs.
Although the yurex driver handles -EILSEQ errors in this way, it
doesn't do the same for -EPROTO (as discovered by the syzbot fuzzer)
or other unrecognized errors. This patch adjusts the driver so that
it doesn't log an error message for -EPROTO or -ETIME, and it doesn't
retry after any errors.
Reported-and-tested-by: syzbot+b24d736f18a1541ad550@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909171245410.1590-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg statements in the completion handlers
which relies on said pointer.
The pointer was also dereferenced unconditionally in a dev_dbg statement
release() something which would lead to a NULL-deref whenever a device
was disconnected before the final character-device close if debugging
was enabled.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes: 1ef37c6047 ("USB: adutux: remove custom debug macro and module parameter")
Fixes: 66d4bc30d1 ("USB: adutux: remove custom debug macro")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190925092913.8608-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix NULL-pointer dereferences on open() and write() which can be
triggered by a malicious USB device.
The current URB allocation helper would fail to initialise the newly
allocated URB if the device has unexpected endpoint descriptors,
something which could lead NULL-pointer dereferences in a number of
open() and write() paths when accessing the URB. For example:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:usb_clear_halt+0x11/0xc0
...
Call Trace:
? tty_port_open+0x4d/0xd0
keyspan_open+0x70/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:keyspan_write+0x14e/0x1f3 [keyspan]
...
Call Trace:
serial_write+0x43/0xa0 [usbserial]
n_tty_write+0x1af/0x4f0
? do_wait_intr_irq+0x80/0x80
? process_echoes+0x60/0x60
tty_write+0x13f/0x2f0
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:keyspan_usa26_send_setup+0x298/0x305 [keyspan]
...
Call Trace:
keyspan_open+0x10f/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
Fixes: fdcba53e2d ("fix for bugzilla #7544 (keyspan USB-to-serial converter)")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
