Fix the following sparse warning:
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:1425:70:
warning: Using plain integer as NULL pointer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Clean up the flow of per-rate txpower limit setting to get rid of
duplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable to limit per-rate max txpower from DT.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Scan abort should be required for the uncompleted hardware scan
interrupted by wifi reset. Otherwise, it is possible that the scan
request after wifi reset gets error code -EBUSY from mac80211 and
then blocks the reconnectting to the access point.
Fixes: 0c1ce98846 ("mt76: mt7921: add wifi reset support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce chip_reset knob in mt7921 debugfs to export a way to users
able to trigger wifi reset, and group the similar operations
previously defined in chip_config in the same knob.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Wake the chip before configuring the mcu log level
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dump mcu command code in hex and related prefix to help debugging
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of init work since firmware loading is already performed in
mt7921_init_hardware
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.
Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For MT7663, the availability of the patch files is used to detect, which
corresponding firmware is going to be used (AP firmware or STA offload
firmware). If the ROM patch was already applied, it could attempt to
load the wrong firmware (without considering the alternative).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7663 uses different bits for communicating reset commands/status between MCU
and host. Also add an extra initial reset command.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dump the tx power table saved in offload firmware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for rate-txpower compensation for mt7663/mt7921 chipsets.
Rate-txpower limit is specified through dts
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7663 mcu relies on different APIs to configure APIs per-rate power limit
respect to mt7615 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Limits are used to update the channel max_power settings and also passed
to the firmware on channel changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This subnode can be used to set per-rate tx power limits either per
country code / regdomain or globally.
These limits are typically provided by the device manufacturers and are
used to limit sideband emissions and stay within regulatory limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce power-limits node in mt76 binding in order to specify
per-rate power limit values for each 802.11n/802.11ac rate
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
After DMA reset, tx status information for queued frames will never arrive.
Flush the queue to free skbs immediately instead of waiting for a timeout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid memory leaks, clean the dma engine unloading the
module
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We should use ieee80211_free_txskb() to report skb status avoid wrong
aql accounting after reset.
Cc: stable@vger.kernel.org
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt7615_mac_reset_work(), make sure freeing skbs after mt7615_dma_reset().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt7915_mac_reset_work(), make sure freeing skbs after mt7915_dma_reset().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915_tx_token_put() should get call before mt76_free_pending_txwi().
Fixes: f285dfb985 ("mt76: mt7915: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_tx_token_put() should get call before mt76_free_pending_txwi().
Fixes: a6275e9346 ("mt76: mt7615: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix ofdm rate index and ldpc setting in rate setting field of tx
descriptor.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rework mt7915_tm_set_tx_len() with mt76_testmode_alloc_skb() to support
larger packet based on a longer tx_time.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support to send larger packet in testmode to meet requirements
of some test cases.
The limit of max packet size is determined based on tx rate mode setting.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Once beacon content is changed, we update the content to wifi card by
send_beacon_frame(). Then, STA with PS can wake up properly to receive its
packets.
Since we update beacon content to PCI wifi devices every beacon interval,
the only one usb device, 8192CU, needs to update beacon content when
mac80211 calling set_tim.
Reported-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419065956.6085-1-pkshih@realtek.com
We used to stop napi before disabling irqs. And it turns out
to cause some problem when we try to stop device while interrupt arrives.
To safely stop pci, we do three steps:
1. disable interrupt
2. synchronize_irq
3. stop_napi
Since step 2 and 3 may not finish as expected when interrupt is enabled,
use rtwpci->running to decide whether interrupt should be re-enabled at
the time.
Fixes: 9e2fd29864 ("rtw88: add napi support")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210415084703.27255-4-pkshih@realtek.com
If there are lots of packets to be transmitted, the driver would check
whether the available descriptors are sufficient according the read/write
point of tx queue. Once the available descriptor is not enough,
ieee80211_stop_queue is called.
TX ISR, meanwhile, is releasing the tx resources after the packets are
transmitted. This routine may call ieee80211_wake_queue by checking the
available descriptor.
The potential queue stop problem would occur when the tx queue is
stopped due to the heavy traffic. Then thare is no chance to wake the
queue up because the read point is not updated immediately, as a result,
no more packets coulde be transmitted in this queue.
This patch makes sure the ieee80211_wake_queue could be called properly
and avoids the race condition when ring->r.rp, ring->queue_stopped are
updated.
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210415084703.27255-3-pkshih@realtek.com
The value of GET_RX_DESC_SWDEC() indicates that if this RX
packet requires software decryption or not. And software
decryption is required when the packet was encrypted and the
hardware failed to decrypt it.
So, GET_RX_DESC_SWDEC() is negative does not mean that this
packet is decrypted, it might just have no encryption at all.
To actually see if the packet is decrypted, driver needs to
further check if the hardware has successfully decrypted it,
with a specific type of encryption algorithm.
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210415084703.27255-2-pkshih@realtek.com
gap-k is a calibration mechanism to eliminate power gaps between
two nearly rate groups.
This mechanism improves performance in long range test by applying
proper power value to those rate groups which have nonlinear power gap.
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419003748.3224-3-pkshih@realtek.com
This patch doesn't change logic at all, just a refactor patch.
1. Move BIT MASK and BIT definition along with the register definition
2. Remove redundant definition
3. Align macros with Tab key
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419003748.3224-2-pkshih@realtek.com
The mhi_wwan_rx_budget_dec function is supposed to return true if
RX buffer budget has been successfully decremented, allowing to queue
a new RX buffer for transfer. However the current implementation is
broken when RX budget is '1', in which case budget is decremented but
false is returned, preventing to requeue one buffer, and leading to
RX buffer starvation.
Fixes: fa588eba63 ("net: Add Qcom WWAN control driver")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c329e5afb4 ("net: phy: at803x: select correct page on
config init") selects the copper page during probe. This fails if the
copper page was already selected. In this case, the value of the copper
page (which is 1) is propagated through phy_restore_page() and is
finally returned for at803x_probe(). Fix it, by just using the
at803x_page_write() directly.
Also in case of an error, the regulator is not disabled and leads to a
WARN_ON() when the probe fails. This couldn't happen before, because
at803x_parse_dt() was the last call in at803x_probe(). It is hard to
see, that the parse_dt() actually enables the regulator. Thus move the
regulator_enable() to the probe function and undo it in case of an
error.
Fixes: c329e5afb4 ("net: phy: at803x: select correct page on config init")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix phase offset calculation.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that enetc supports flow control we have to make sure the settings in
the IERB are correct. Therefore, we actually depend on the enetc-ierb
module. Previously it was possible that this module was disabled while the
enetc was enabled. Fix it by automatically select the enetc-ierb module.
Fixes: e7d48e5fbf ("net: enetc: add a mini driver for the Integrated Endpoint Register Block")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() is supposed to be followed by
skb_reserve(skb, NET_IP_ALIGN), so that IP headers are word-aligned.
(Best practice is to reserve NET_IP_ALIGN+NET_SKB_PAD, but the NET_SKB_PAD
part is only a performance optimization if tunnel encaps are added.)
Unfortunately virtio_net has not provisioned this reserve.
We can only use build_skb() for arches where NET_IP_ALIGN == 0
We might refine this later, with enough testing.
Fixes: fb32856b16 ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
bit operation helpers such as test_bit, clear_bit, etc take bit
position as parameter and not value. Current usage causes double
shift => BIT(BIT(0)). Fix that in wwan_core and mhi_wwan_ctrl.
Fixes: 9a44c1cc63 ("net: Add a WWAN subsystem")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Waldekranz says:
====================
net: dsa: Allow default tag protocol to be overridden from DT
This is a continuation of the work started in this patch:
https://lore.kernel.org/netdev/20210323102326.3677940-1-tobias@waldekranz.com/
In addition to the mv88e6xxx support to dynamically change the
protocol, it is now possible to override the protocol from the device
tree. This means that when a board vendor finds an incompatibility,
they can specify a working protocol in the DT, and users will not have
to worry about it.
Some background information:
In a system using an NXP T1023 SoC connected to a 6390X switch, we
noticed that TO_CPU frames where not reaching the CPU. This only
happened on hardware port 8. Looking at the DSA master interface
(dpaa-ethernet) we could see that an Rx error counter was bumped at
the same rate. The logs indicated a parser error.
It just so happens that a TO_CPU coming in on device 0, port 8, will
result in the first two bytes of the DSA tag being one of:
00 40
00 44
00 46
My guess was that since these values looked like 802.3 length fields,
the controller's parser would signal an error if the frame length did
not match what was in the header.
This was later confirmed using two different workarounds provided by
Vladimir. Unfortunately these either bypass or ignore the hardware
parser and thus robs working combinations of the ability to do RSS and
other nifty things. It was therefore decided to go with the option of
a DT override.
v1 -> v2:
- Fail if the device does not support changing protocols instead of
falling back to the default. (Andrew)
- Only call change_tag_protocol on CPU ports. (Andrew/Vladimir)
- Only allow changing the protocol on chips that have at least
"undocumented" level of support for EDSA. (Andrew).
- List the supported protocols in the binding documentation. I opted
for only listing the protocols that I have tested. As more people
test their drivers, they can add them. (Rob)
v2 -> v3:
- Rename "dsa,tag-protocol" -> "dsa-tag-protocol". (Rob)
- Some cleanups to 4/5. (Vladimir)
- Add a comment detailing how tree/driver agreement on the tag
protocol is enforced. (Vladimir).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'dsa-tag-protocol' is used to force a switch tree to use a
particular tag protocol, typically because the Ethernet controller
that it is connected to is not compatible with the default one.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some combinations of tag protocols and Ethernet controllers are
incompatible, and it is hard for the driver to keep track of these.
Therefore, allow the device tree author (typically the board vendor)
to inform the driver of this fact by selecting an alternate protocol
that is known to work.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously DSA ports were also included, on the assumption that the
protocol used by the CPU port had to the matched throughout the entire
tree.
As there is not yet any consumer in need of this, drop the call.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
